# AmITX-CF-G User’s Manual

Mini-ITX Embedded Motherboard with 8th and 9th Gen. Intel® Core™ i7/i5/i3 Processors and Intel® Q370/H310 Chipset

![Close-up of a green printed circuit board with various electronic components and connectors (no readable text or symbols)](.amitx-cf-g-50m-00093-1000-20/4d6b91bce4fe06c32af68f15625219790423f9ebd8da1eccda8110a98ccbcdb0.jpg)

Manual Rev.: 2.0

Revision Date: September 23, 2022

Part Number: 50M-00093-1000

# Preface

# Copyright

Copyright 2022 ADLINK Technology, Inc. This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer.

# Disclaimer

The information in this document is subject to change without prior notice in order to improve reliability, design, and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.

# Environmental Responsibility

ADLINK is committed to fulfill its social responsibility to global environmental preservation through compliance with the European Union's Restriction of Hazardous Substances (RoHS) directive and Waste Electrical and Electronic Equipment (WEEE) directive. Environmental protection is a top priority for ADLINK. We have enforced measures to ensure that our products, manufacturing processes, components, and raw materials have as little impact on the environment as possible. When products are at their end of life, our customers are encouraged to dispose of them in accordance with the product disposal and/or recovery programs prescribed by their nation or company.

![Symbol of a trash bin crossed with a diagonal line and a horizontal bar below (no text or labels)](.amitx-cf-g-50m-00093-1000-20/535d7dcd11da924b5b350ff02134011b766b8333aca21239c32d3385e1b3af8b.jpg)

Battery Labels (for products with battery)

![Simple line drawing of a trash bin with two crossed lines indicating no waste or prohibition (no text or symbols)](.amitx-cf-g-50m-00093-1000-20/d6937de786a0d11d57e08776c33f1d448502232aa4f084d3d8bf2dde8857f74f.jpg)

![Li-ion](.amitx-cf-g-50m-00093-1000-20/62255eba179ec8f5f32a57426aabe2dfdbb703e283e38121369fe2182c409a83.jpg)

![RECYCLE\nRBRC\nLi-ion\n7.800.822.8837](.amitx-cf-g-50m-00093-1000-20/5e9f3b761093b665666b7f14756a0bf248294c0bd551ee7212a03001d89a2af9.jpg)

![廢電池請回收](.amitx-cf-g-50m-00093-1000-20/84ab32a4d14748dd8f4a603da7b1a9cfa5455b2a4acafb43d77cb79412dac272.jpg)

# California Proposition 65 Warning

![The image displays a yellow equilateral triangle with a thick black border. Inside the triangle is a large black exclamation point (!).](.amitx-cf-g-50m-00093-1000-20/6ec73b327ceb68bfed1094761efd033daeda9988fc3ad23db1f9d30fece9e82b.jpg)

WARNING: This product can expose you to chemicals including acrylamide, arsenic, benzene, cadmium, Tris(1,3-dichloro-2-propyl)phosphate (TDCPP), 1,4-Dioxane, formaldehyde, lead, DEHP, styrene, DINP, BBP, PVC, and vinyl materials, which are known to the State of California to cause cancer, and acrylamide, benzene, cadmium, lead, mercury, phthalates, toluene, DEHP, DIDP, DnHP,

DBP, BBP, PVC, and vinyl materials, which are known to the State of California to cause birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

# Trademarks

Product names mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks of their respective companies.

Revision History

<table><tr><td>Revision</td><td>Description</td><td>Date</td></tr><tr><td>1.0</td><td>Initial release</td><td>February 26, 2021</td></tr><tr><td>2.0</td><td>General update, changed LAN chip and SER1 pinout</td><td>September 23, 2022</td></tr></table>

# Table of Contents

# Preface ...

# Table of Contents....

# List of Figures ....

# List of Tables .............. .vi

# 1. Introduction...

1.1. Packing List..
1.2. Optional Accessories .

# 2. Specifications ...

2.1. Core System . .3
2.2. Rear I/O Connectors .. .3
2.3. Debug Connector.. .3
2.4. Internal Headers and Connectors . 4
2.5. Form Factor.. 4
2.6. SEMA Board Controller.. 4
2.7. Video.. .5
2.8. Audio.. .5
2.9. LAN . .5
2.10. Trusted Platform Module (TPM).. .5
2.11. Power Specification.. .5
2.12. Temperatures.. ..10
2.13. Environmental . ..10
2.14. Operating Systems.. ..10
2.15. Functional Block Diagram . .11

# 3. Mechanical Layout .. .13

3.1. Connector Locations .. ..13
3.2. Mechanical Dimensions . ..14
3.3. Thermal Solutions .. .. 15

# 4. Connectors and Jumpers ....... .17

4.1. Rear IO Connectors . .17
4.2. Internal Connectors.. ..19
4.3. Jumper and Switch Settings.. ..29
4.4. Onboard Connector Information.. .32

# 5. Driver Installation .... .33

# 6. Smart Embedded Management Agent (SEMA) .............. .35

6.1. Board Specific SEMA Functions . .35

# 7. System Resources .... .39

7.1. System Memory Map . ..39
7.2. I/O Map . .. 39
7.3. Interrupt Request (IRQ) Lines .. ..40
7.4. PCI Configuration Space Map.. ..42

7.5. PCI Interrupt Routing Map . .. 43
7.6. SMBus Slave Address .. .. 43

# 8. BIOS Setup.... ..45

8.1. BIOS Setup Menu .. .. 45
8.2. Menu Structure.. .. 46
8.3. Main Menu . ..47
8.4. Advanced .. ..47
8.5. Chipset.. .. 56
8.6. Security ... ..59
8.7. Boot.. .. 59
8.8. Save & Exit . .. 61

# Safety Instructions... .62

# Getting Service.... .63

# List of Figures

Figure 1: AmITX-CF-G Functional Block Diagram .. ...11
Figure 2: AmITX-CF-G Rear I/O. ..13
Figure 3: AmITX-CF-G Component-Side Connectors.. ...13
Figure 4: AmITX-CF-G Mechanical Dimensions .. ...14
Figure 5: Jumper and Switch Locations . ..29

# List of Tables

Table 1: AmITX-CF-G Model Numbers ..

Table 2: AmITX-CF-G Onboard Connector Information.. ..32

Table 3: SEMA Onboard Voltage Monitor.. ...35

Table 4: SEMA BMC Status .. ...36

Table 5: SEMA Exception Codes .. ..36

Table 6: SEMA BMC Flags.. ...37

Table 7: System Memory Map . ...39

Table 8: I/O Map.. ...39

Table 9: IRQ Lines PIC Mode.. ...40

Table 10: IRQ Lines APIC Mode . ..41

Table 11: PCI Configuration Space Map. ..42

Table 12: PCI Interrupt Routing Map.. ...43

Table 13: SMBus Slave Address......... ...43

# 1. Introduction

The AmITX-CF-G is a Mini-ITX motherboard supporting the Desktop $8 ^ { \mathrm { t h } }$ and ${ \mathfrak { g m } }$ Generation Intel® Core™ i7/i5/i3 and Pentium®/Celeron® Processors with Intel® Q370/H310 Chipsets. The AmITX-CF-G is specifically designed for customers who need high-level processing and graphics performance with a long product life solution.

The AmITX-CF-G features three DisplayPorts, dual Gigabit Ethernet ports, USB 3.0 ports, USB 2.0 ports, SATA 6 Gb/s ports, and High Definition Audio with 7.1 channels. Expansion is provided by one PCIe x16, one PCIe x1, one M.2 and one mini-PCIe slot. The onboard feature connector provides GPIO, SMBus, and I2C support. The board is equipped with SPI AMI EFI BIOS, supporting embedded features such as hardware monitor and watchdog timer.

Table 1: AmITX-CF-G Model Numbers

<table><tr><td>Model Number</td><td>Chipset Implemented</td></tr><tr><td>AmITX-CF-G-Q370</td><td>Intel® Q370</td></tr><tr><td>AmITX-CF-G-H310</td><td>Intel® H310</td></tr></table>

Latest revision of the datasheet, user’s manual, BIOS, drivers, and board support packages, can be downloaded from the product webpage on the ADLINK web site: www.adlinktech.com.

# 1.1. Packing List

• AmITX-CF-G Mini-ITX motherboard
ATX/AT power cable (P/N: 30-20872-1000)
SATA dual power cable (P/N: 30-20875-0000)
SATA cable (P/N: 30-10057-0600)
• Rear I/O shield (P/N: 34-25314-0000)

# 1.2. Optional Accessories

COM port cable, 1 port (P/N: 30-20876-0000)
• USB 2.0 cable, 2 ports for AmITX-CF-G-H310 (P/N: 30-20874-1000)
• USB 3.0 cable, 2 ports for AmITX-CF-G-Q370 (P/N: 30-20963-0000)
• ADi-SCOT (Software Chain of Trust) for gaming customization BIOS requirement (RSA-2048 private key)

This page intentionally left blank.

# 2. Specifications

# 2.1. Core System

<table><tr><td rowspan="3">CPU</td><td>Embedded 9thGen. Intel® CoreTM i7/i5/i3 and Pentium®/Celeron® Processor, LGA1151 socketIntel® CoreTM i7-9700TE Processor, 8C, 1.8/3.8GHz, 12M, 35WIntel® CoreTM i7-9700E Processor, 8C, 2.6/4.4GHz, 12M, 65WIntel® CoreTM i5-9500TE Processor, 6C, 2.2/3.6GHz, 9M, 35WIntel® CoreTM i5-9500E Processor, 6C, 3.0/4.2GHz, 9M, 65WIntel® CoreTM i3-9100E Processor, 4C, 3.1/3.7GHz, 6M, 65WIntel® CoreTM i3-9100TE Processor, 4C, 2.2/3.2GHz, 6M, 35W</td></tr><tr><td>Embedded 8thGen. Intel® CoreTM i7/i5/i3 and Pentium®/Celeron® Processor, LGA1151 socketIntel® CoreTM i7-8700 Processor, 6C, 3.2/4.6GHz, 12M, 65WIntel® CoreTM i7-8700T Processor, 6C, 2.4/4.0GHz, 12M, 35WIntel® CoreTM i5-8500 Processor, 6C, 3.0/4.1GHz, 9M, 65WIntel® CoreTM i5-8500T Processor, 6C, 2.1/3.5GHz, 9M, 35WIntel® CoreTM i3-8100 Processor, 4C, 3.6GHz, 6M, 65WIntel® CoreTM i3-8100T Processor, 4C, 3.1GHz, 6M, 35WIntel® Pentium® Gold G5400 Processor, 2C, 3.7GHz, 4M, 58WIntel® Pentium® Gold G5400T Processor, 2C, 3.1GHz, 4M, 35WIntel® Celeron® G4900 Processor, 2C, 3.1GHz, 2M, 54WIntel® Celeron® G4900T Processor, 2C, 2.9GHz, 2M, 35W</td></tr><tr><td>Note:The availability of features may vary between processor SKUs and operating systems.</td></tr><tr><td>Chipset</td><td>Intel® Q370/H310 Chipset</td></tr><tr><td>Memory</td><td>Dual-channel non-ECC 2400 MHz DDR4 memory up to 32GB in dual SODIMM sockets</td></tr><tr><td>Embedded BIOS</td><td>AMI EFI in 16MB SPI BIOS</td></tr></table>

# 2.2. Rear I/O Connectors

<table><tr><td>Display</td><td>3x DisplayPort (Q370), 2x DisplayPort (H310)</td></tr><tr><td>LAN</td><td>Dual GbE RJ-45</td></tr><tr><td>USB</td><td>4x USB 3.0; 4x USB 2.0</td></tr><tr><td>Audio</td><td>7.1 channel audio via 5 jacks and S/PDIF output on rear I/O</td></tr></table>

# 2.3. Debug Connector

40-pin Multipurpose Flat Cable Connector: used in combination with DB-40 debug module providing BIOS POST code LED, BMC access, SPI BIOS flashing, Power Testpoints, Debug LEDs

2.4. Internal Headers and Connectors

<table><tr><td>PCI Express Slots</td><td>PCIe x16 (Gen3)PCIe x1 (Gen2)1x full-size Mini-PCIe slot (Q370: PCIe x1, mSATA and USB 2.0 / H310: PCIe x1)1x M.2 (M key, 2242, NVMe support; H310: PCIe x1 Gen2 signal)</td></tr><tr><td>USB</td><td>2x USB 3.0 onboard header (Q370)1x USB 2.0 onboard header (H310)1x USB 3.0 vertical connector (H310 only supports USB2.0)</td></tr><tr><td>SATA</td><td>3x SATA 6 Gbps ports (Jumper select NA/3.3V/5V for SATA1 and SATA2 to deliver power by SATA pin7; Default is NA)2x SATA power connectors</td></tr><tr><td>Serial</td><td>3x RS-232 headers, 1x RS-232/422/485 header (supports NC/5V/12V power by jumper selection)1x CCTALK x2 on internal header</td></tr><tr><td>Other</td><td>Front Panel HeaderAudio HeaderFeature Connector HeaderSPI HeaderATX Power Connector (14-pin)</td></tr></table>

# 2.5. Form Factor

Mini-ITX: 170mm x 170mm

# 2.6. SEMA Board Controller

ADLINK Smart Embedded Management Agent (SEMA)

• Voltage/Current monitoring
• Logistics and Forensic information
• Flat Panel Control
• General Purpose I2C
• Failsafe BIOS (dual BIOS)
• Watchdog Timer and Fan Control

# 2.7. Video

<table><tr><td>GPU Feature Support</td><td>Intel® 9th generation LP graphics core architecture with up to 18 execution units supporting DirectX 11/12, OGL4.3/4.4, and up to three independent, simultaneous displays</td></tr><tr><td>Display Interface Support</td><td>3x DisplayPort v1.2 with resolution up to 4096 x 2304 @ 60Hz (3x DisplayPort (Q370), 2x DisplayPort (H310))</td></tr></table>

# 2.8. Audio

<table><tr><td>Integrated</td><td>Intel® HD Audio on chipset</td></tr><tr><td>Audio Codec</td><td>Realtek ALC888</td></tr><tr><td>Interfaces</td><td>7.1 channel audio via 5 jacks and S/PDIF output on rear I/O7.1 channel audio signals and S/PDIF output via internal header</td></tr></table>

# 2.9. LAN

<table><tr><td>Realtek</td><td>2x Realtek RTL8119-CG Ethernet controller</td></tr><tr><td>Interface</td><td>10/100/1000 GbE connection</td></tr></table>

# 2.10. Trusted Platform Module (TPM)

<table><tr><td>Chipset</td><td>Infineon SLB9665XT</td></tr><tr><td>Type</td><td>TPM2.0</td></tr></table>

# 2.11. Power Specification

<table><tr><td>Power Modes</td><td>AT and ATX mode</td></tr><tr><td>Standard Voltage Input</td><td>ATX = 12VDC ±5%, 5Vsb ±5% or AT = 12V ±5%</td></tr><tr><td>Power Management</td><td>ACPI 4.0 compliant</td></tr><tr><td>Power States</td><td>Supports C1-C6, S0, S1, S4, S3, S5, (Wake-on-USB S3/S4, WoL S3/S4/S5)</td></tr></table>

# 2.11.1. Power Consumption

ATX mode (with standard power supply 24-pin)

<table><tr><td>Processor</td><td>i3-8100T 3.1 35W</td><td>i5-8500T 2.10 35W</td><td>i7-9700TE 1.8 35W</td><td>i5-9500E 3.0 65W</td><td>i7-8700 3.2 65W</td></tr><tr><td>Chipset</td><td>Q370</td><td>Q370</td><td>Q370</td><td>Q370</td><td>Q370</td></tr><tr><td>Memory</td><td>16G 2400MHz</td><td>16G 2400MHz</td><td>16G 2400MHz</td><td>16G 2400MHz</td><td>16G 2400MHz</td></tr><tr><td>Graphics</td><td>Q370</td><td>Q370</td><td>Q370</td><td>Q370</td><td>Q370</td></tr><tr><td>HDD</td><td>M.2 (S42) 3TG6-P</td><td>M.2 (S42) 3TG6-P</td><td>M.2 (S42) 3TG6-P</td><td>M.2 (S42) 3TG6-P</td><td>M.2 (S42) 3TG6-P</td></tr><tr><td>OS</td><td>Win 10 Enterprise</td><td>Win 10 Enterprise</td><td>Win 10 Enterprise</td><td>Win 10 Enterprise</td><td>Win 10 Enterprise</td></tr><tr><td colspan="6">Windows Idle mode/Enable EIST/Enable Turbo boost</td></tr><tr><td>3.3A(A)orange</td><td>0.1</td><td>0.11</td><td>0.11</td><td>0.12</td><td>0.1</td></tr><tr><td>5V(A)red</td><td>0.13</td><td>0.13</td><td>0.13</td><td>0.13</td><td>0.13</td></tr><tr><td>+12V(A)yellow</td><td>1.08</td><td>1.18</td><td>1.1</td><td>1.37</td><td>1.21</td></tr><tr><td>5VSB(A)purple</td><td>0.01</td><td>0.01</td><td>0.01</td><td>0.01</td><td>0.01</td></tr><tr><td>Power Consumption(W)</td><td>13.99</td><td>15.223</td><td>14.263</td><td>17.536</td><td>15.55</td></tr><tr><td colspan="6">Windows Idle mode/Disable EIST/Disable Turbo boost</td></tr><tr><td>3.3A(A)orange</td><td>0.11</td><td>0.1</td><td>0.1</td><td>0.12</td><td>0.1</td></tr><tr><td>5V(A)red</td><td>0.15</td><td>0.14</td><td>0.13</td><td>0.13</td><td>0.13</td></tr><tr><td>+12V(A)yellow</td><td>1.47</td><td>1.49</td><td>1.5</td><td>1.64</td><td>1.87</td></tr><tr><td>5VSB(A)purple</td><td>0.01</td><td>0.01</td><td>0.01</td><td>0.02</td><td>0.01</td></tr><tr><td>Power Consumption(W)</td><td>18.803</td><td>18.96</td><td>19.03</td><td>20.826</td><td>23.47</td></tr><tr><td colspan="6">Windows Typical mode/Enable EIST/Enable Turbo boost</td></tr><tr><td>3.3A(A)orange</td><td>0.1</td><td>0.11</td><td>0.11</td><td>0.11</td><td>0.11</td></tr><tr><td>5V(A)red</td><td>0.17</td><td>0.16</td><td>0.17</td><td>0.16</td><td>0.17</td></tr><tr><td>+12V(A)yellow</td><td>13.34</td><td>14.54</td><td>16.67</td><td>20.1</td><td>21.43</td></tr><tr><td>5VSB(A)purple</td><td>0.01</td><td>0.01</td><td>0.02</td><td>0.01</td><td>0.01</td></tr><tr><td>Power Consumption(W)</td><td>161.31</td><td>175.693</td><td>201.353</td><td>242.413</td><td>258.423</td></tr><tr><td colspan="6">Windows Typical mode/Disable EIST/Disable Turbo boost</td></tr><tr><td>3.3A(A)orange</td><td>0.1</td><td>0.11</td><td>0.11</td><td>0.1</td><td>0.1</td></tr><tr><td>5V(A)red</td><td>0.17</td><td>0.16</td><td>0.17</td><td>0.16</td><td>0.17</td></tr><tr><td>+12V(A)yellow</td><td>13.66</td><td>13.39</td><td>13.82</td><td>15.65</td><td>16.5</td></tr><tr><td>5VSB(A)purple</td><td>0.01</td><td>0.01</td><td>0.01</td><td>0.01</td><td>0.01</td></tr><tr><td>Power Consumption(W)</td><td>165.15</td><td>161.893</td><td>167.103</td><td>188.98</td><td>199.23</td></tr></table>

ATX mode (with standard power supply 24-pin)

<table><tr><td colspan="6">Windows Max mode/Enable EIST/Enable Turbo boost</td></tr><tr><td>3.3A(A)orange</td><td>0.1</td><td>0.1</td><td>0.12</td><td>0.09</td><td>0.11</td></tr><tr><td>5V(A)red</td><td>0.17</td><td>0.16</td><td>0.18</td><td>0.16</td><td>0.17</td></tr><tr><td>+12V(A)yellow</td><td>13.65</td><td>16.31</td><td>16.86</td><td>22.33</td><td>24.13</td></tr><tr><td>5VSB(A)purple</td><td>0.01</td><td>0.01</td><td>0.02</td><td>0.01</td><td>0.01</td></tr><tr><td>Power Consumption(W)</td><td>165.03</td><td>196.9</td><td>203.716</td><td>269.107</td><td>290.823</td></tr><tr><td colspan="6">Windows Max mode/Disable EIST/Disable Turbo boost</td></tr><tr><td>3.3A(A)orange</td><td>0.1</td><td>0.1</td><td>0.11</td><td>0.1</td><td>0.11</td></tr><tr><td>5V(A)red</td><td>0.17</td><td>0.16</td><td>0.17</td><td>0.16</td><td>0.16</td></tr><tr><td>+12V(A)yellow</td><td>14.09</td><td>14.49</td><td>14.07</td><td>16.52</td><td>19.58</td></tr><tr><td>5VSB(A)purple</td><td>0.01</td><td>0.01</td><td>0.01</td><td>0.01</td><td>0.01</td></tr><tr><td>Power Consumption(W)</td><td>170.31</td><td>175.06</td><td>170.103</td><td>199.42</td><td>236.173</td></tr><tr><td colspan="6">System S3 mode</td></tr><tr><td>3.3A(A)orange</td><td>0.01</td><td>0.01</td><td>0.01</td><td>0.01</td><td>0.02</td></tr><tr><td>5V(A)red</td><td>0.01</td><td>0</td><td>0.01</td><td>0.02</td><td>0.01</td></tr><tr><td>+12V(A)yellow</td><td>0.01</td><td>0.01</td><td>0.02</td><td>0.01</td><td>0.01</td></tr><tr><td>5VSB(A)purple</td><td>0.21</td><td>0.22</td><td>0.22</td><td>0.24</td><td>0.21</td></tr><tr><td>Power Consumption(W)</td><td>1.253</td><td>1.253</td><td>1.423</td><td>1.453</td><td>1.286</td></tr><tr><td colspan="6">System S4 mode</td></tr><tr><td>3.3A(A)orange</td><td>0.01</td><td>0.01</td><td>0.01</td><td>0.01</td><td>0.01</td></tr><tr><td>5V(A)red</td><td>0.01</td><td>0.01</td><td>0</td><td>0.01</td><td>0.01</td></tr><tr><td>+12V(A)yellow</td><td>0.01</td><td>0.01</td><td>0.01</td><td>0.02</td><td>0.01</td></tr><tr><td>5VSB(A)purple</td><td>0.16</td><td>0.17</td><td>0.18</td><td>0.19</td><td>0.18</td></tr><tr><td>Power Consumption(W)</td><td>1.003</td><td>1.053</td><td>1.053</td><td>1.273</td><td>1.103</td></tr><tr><td colspan="6">System S5 mode with ECO disabled</td></tr><tr><td>3.3A(A)orange</td><td>0.01</td><td>0.01</td><td>0.01</td><td>0.01</td><td>0.02</td></tr><tr><td>5V(A)red</td><td>0.01</td><td>0.01</td><td>0.01</td><td>0.01</td><td>0.01</td></tr><tr><td>+12V(A)yellow</td><td>0.01</td><td>0.01</td><td>0.01</td><td>0.02</td><td>0.01</td></tr><tr><td>5VSB(A)purple</td><td>0.17</td><td>0.17</td><td>0.18</td><td>0.2</td><td>0.16</td></tr><tr><td>Power Consumption (W)</td><td>1.053</td><td>1.053</td><td>1.103</td><td>1.323</td><td>1.036</td></tr></table>

ATX mode (with standard power supply 24-pin)

<table><tr><td colspan="6">System S5 mode with ECO enabled</td></tr><tr><td>3.3A(A)orange</td><td>0.01</td><td>0.01</td><td>0.01</td><td>0.01</td><td>0.02</td></tr><tr><td>5V(A)red</td><td>0.01</td><td>0.01</td><td>0.01</td><td>0.01</td><td>0.02</td></tr><tr><td>+12V(A)yellow</td><td>0.01</td><td>0.01</td><td>0.01</td><td>0.01</td><td>0</td></tr><tr><td>5VSB(A)purple</td><td>0.02</td><td>0.02</td><td>0.03</td><td>0.04</td><td>0.01</td></tr><tr><td>Power Consumption(W)</td><td>0.303</td><td>0.303</td><td>0.353</td><td>0.403</td><td>0.216</td></tr></table>

ATX mode (with 12V adapter)

<table><tr><td>Processor</td><td>i3-8100T 3.1 35W</td><td>i5-8500T 2.10 35W</td><td>i7-9700TE 1.8 35W</td><td>i5-9500E 3.0 65W</td><td>i7-8700 3.2 65W</td></tr><tr><td>Chipset</td><td>Q370</td><td>Q370</td><td>Q370</td><td>Q370</td><td>Q370</td></tr><tr><td>Memory</td><td>16G 2400MHz</td><td>16G 2400MHz</td><td>16G 2400MHz</td><td>16G 2400MHz</td><td>16G 2400MHz</td></tr><tr><td>Graphics</td><td>Q370</td><td>Q370</td><td>Q370</td><td>Q370</td><td>Q370</td></tr><tr><td>HDD</td><td>M.2 (S42) 3TG6-P</td><td>M.2 (S42) 3TG6-P</td><td>M.2 (S42) 3TG6-P</td><td>M.2 (S42) 3TG6-P</td><td>M.2 (S42) 3TG6-P</td></tr><tr><td>OS</td><td>Win 10 Enterprise</td><td>Win 10 Enterprise</td><td>Win 10 Enterprise</td><td>Win 10 Enterprise</td><td>Win 10 Enterprise</td></tr><tr><td colspan="6">Windows Idle mode/Enable EIST/Enable Turbo boost</td></tr><tr><td>3.3A(A)</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td></tr><tr><td>5V(A)</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td></tr><tr><td>12V(A)</td><td>1.32</td><td>1.19</td><td>1.1</td><td>1.49</td><td>1.51</td></tr><tr><td>5VSB(A)</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td></tr><tr><td>Power Consumption(W)</td><td>15.84</td><td>14.28</td><td>13.2</td><td>17.88</td><td>18.12</td></tr><tr><td colspan="6">Windows Idle mode/Disable EIST/Disable Turbo boost</td></tr><tr><td>3.3A(A)</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td></tr><tr><td>5V(A)</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td></tr><tr><td>12V(A)</td><td>1.55</td><td>1.48</td><td>1.35</td><td>1.73</td><td>1.88</td></tr><tr><td>5VSB(A)</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td></tr><tr><td>Power Consumption(W)</td><td>18.6</td><td>17.76</td><td>16.2</td><td>20.76</td><td>22.56</td></tr><tr><td colspan="6">Windows Typical mode/Enable EIST/Enable Turbo boost</td></tr><tr><td>3.3A(A)</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td></tr><tr><td>5V(A)</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td></tr><tr><td>12V(A)</td><td>13.77</td><td>14.41</td><td>16.35</td><td>19.35</td><td>21.66</td></tr><tr><td>5VSB(A)</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td></tr><tr><td>Power Consumption(W)</td><td>165.24</td><td>172.92</td><td>196.2</td><td>232.2</td><td>259.92</td></tr></table>

ATX mode (with 12V adapter)

<table><tr><td colspan="6">Windows Typical mode/Disable EIST/Disable Turbo boost</td></tr><tr><td>3.3A(A)</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td></tr><tr><td>5V(A)</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td></tr><tr><td>12V(A)</td><td>12.71</td><td>13.03</td><td>13.48</td><td>15.6</td><td>15.99</td></tr><tr><td>5VSB(A)</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td></tr><tr><td>Power Consumption(W)</td><td>152.52</td><td>156.36</td><td>161.76</td><td>187.2</td><td>191.88</td></tr><tr><td colspan="6">Windows Max mode/Enable EIST/Enable Turbo boost</td></tr><tr><td>3.3A(A)</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td></tr><tr><td>5V(A)</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td></tr><tr><td>12V(A)</td><td>14.21</td><td>16.12</td><td>18.31</td><td>21.6</td><td>22.5</td></tr><tr><td>5VSB(A)</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td></tr><tr><td>Power Consumption(W)</td><td>170.52</td><td>193.44</td><td>219.72</td><td>259.2</td><td>270</td></tr><tr><td colspan="6">Windows Max mode/Disable EIST/Disable Turbo boost</td></tr><tr><td>3.3A(A)</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td></tr><tr><td>5V(A)</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td></tr><tr><td>12V(A)</td><td>13.06</td><td>14.3</td><td>14.46</td><td>16.49</td><td>18.62</td></tr><tr><td>5VSB(A)</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td></tr><tr><td>Power Consumption(W)</td><td>156.72</td><td>171.6</td><td>173.52</td><td>197.88</td><td>223.44</td></tr><tr><td colspan="6">System S3 mode</td></tr><tr><td>3.3A(A)</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td></tr><tr><td>5V(A)</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td></tr><tr><td>12V(A)</td><td>0.17</td><td>0.17</td><td>0.17</td><td>0.15</td><td>0.14</td></tr><tr><td>5VSB(A)</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td></tr><tr><td>Power Consumption(W)</td><td>2.04</td><td>2.04</td><td>2.04</td><td>1.8</td><td>1.68</td></tr><tr><td colspan="6">System S4 mode</td></tr><tr><td>3.3A(A)</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td></tr><tr><td>5V(A)</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td></tr><tr><td>12V(A)</td><td>0.15</td><td>0.16</td><td>0.15</td><td>0.15</td><td>0.13</td></tr><tr><td>5VSB(A)</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td></tr><tr><td>Power Consumption(W)</td><td>1.8</td><td>1.92</td><td>1.8</td><td>1.8</td><td>1.56</td></tr></table>

ATX mode (with 12V adapter)

<table><tr><td colspan="6">System S5 mode with ECO disable</td></tr><tr><td>3.3A(A)</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td></tr><tr><td>5V(A)</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td></tr><tr><td>12V(A)</td><td>0.15</td><td>0.16</td><td>0.12</td><td>0.15</td><td>0.13</td></tr><tr><td>5VSB(A)</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td></tr><tr><td>Power Consumption(W)</td><td>1.8</td><td>1.92</td><td>1.44</td><td>1.8</td><td>1.56</td></tr><tr><td colspan="6">System S5 mode with ECO Enable</td></tr><tr><td>3.3A(A)</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td></tr><tr><td>5V(A)</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td></tr><tr><td>12V(A)</td><td>0.07</td><td>0.07</td><td>0.06</td><td>0.07</td><td>0.09</td></tr><tr><td>5VSB(A)</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td><td>N/A</td></tr><tr><td>Power Consumption(W)</td><td>0.84</td><td>0.84</td><td>0.72</td><td>0.84</td><td>1.08</td></tr></table>

# 2.12. Temperatures

<table><tr><td>Standard Operating Temperature</td><td>0°C to 60°C</td></tr><tr><td>Storage Temperature</td><td>-20°C to 80°C</td></tr></table>

# 2.13. Environmental

<table><tr><td>Humidity</td><td>40°C @ 95% RH non-condensing</td></tr><tr><td>Shock and Vibration</td><td>IEC 60068-2-64 and IEC-60068-2-27Vibration: 1Grms (5~500 Hz) operating, 3Grms (5~500 Hz) non-operatingShock: 20G (with 11 ms duration, half sine wave) operating, 20G(with 11 ms duration, half sine wave) non-operating</td></tr><tr><td>HALT</td><td>Thermal Stress, Vibration Stress, Thermal Shock and Combined Test</td></tr></table>

# 2.14. Operating Systems

<table><tr><td>Standard Support</td><td>Windows 10 64-bitUbuntu 18.04.x 64-bit</td></tr><tr><td>Extended Support (BSP)</td><td>On request</td></tr></table>

# 2.15. Functional Block Diagram

![Here is an accurate and concise description of the flowchart:\n\n**Top Section**\n*   **Central Block:** Intel® Core™ i7/i5/i3 Processor LGA 1151 Socket\n*   **Left Connections:** Three blocks labeled 'DP 1.2' connect to the processor via 'Display Port A', 'Display Port B', and 'Display Port C'.\n*   **Right Connections:** The processor connects to 'PCIe x16 Slot' (via 'PCIe x16'), 'SODIMM-A DDR4(Non ECC)', and 'SODIMM-B DDR4(Non ECC)'.\n*   **Down Connection:** A 'DMI' connection leads to the chipset below.\n\n**Middle Section (Chipset)**\n*   **Central Block:** Intel® Q370/H310 Chipset\n\n**Left Side Connections (Chipset)**\n*   **USB:**\n    *   '2x USB3.0' connects via 'USB3.0 (P1&2)/USB2.0 (P1&2)'.\n    *   '2x USB3.0' connects via 'USB3.0 (P3&4)/USB2.0(P3&4)'.\n    *   '4x USB2.0' connects via 'USB2.0 (P6~9)'.\n*   **LAN:** 'GLAN RJ45 (Top size)' and 'GLAN RJ45 (Bottom side)' connect to 'GLAN RTL8119-CG' blocks, which connect back to the chipset via 'PCIe x1'.\n*   **System Signals:** 'Front Panel Header' connects via 'System Signals'.\n*   **Audio:**\n    *   'MIC2-IN / LIN E2-Out', 'Center Surround L/R S/PD I F Out', 'Line In Line Out Mic In', and 'Audio Header' connect to 'HDA Codec ALC888S' via 'HDA'.\n    *   'Buzzer' connects directly to the chipset.\n*   **Serial/COM:**\n    *   'COM1 Header' connects via 'RS232/RS422/RS485'.\n    *   'COM2 Header', 'COM3 Header', and 'COM4 Header' connect via 'RS232'.\n    *   'COM5&6 Header' connects via '2x RS232/CCTa Ik'.\n    *   All COM headers connect to 'Super I/O Fintek ALC81866'.\n*   **TPM:** 'TPM 2.0 (SLB96 65)' connects via 'LPC' to the Super I/O block and the chipset.\n\n**Right Side Connections (Chipset)**\n*   **Expansion/Storage:**\n    *   'PCIe x1 Slot' connects via 'PCIe x1'.\n    *   'M.2 (Size: 2242)' connects via 'PClex4 (Q370) / PClex2(H310) 1x SATA3.0 (P3)'.\n    *   'mSATA/Mini PCIe Full size (Top side)' connects via 'USB2.0 (P11)'.\n    *   '3x SATA' connects via '3x SATA3.0(P0~2)'.\n    *   A 'Switch' block connects via 'PCIe x1' and 'SATA3.0 (P4)'.\n*   **USB:**\n    *   'USB Header' connects via 'Q370: 2x USB3.0 (P7&8) H310:1x USB2.0 (P14)'.\n    *   'USB 3.0/2.0 Vertical' connects via 'Q370: 1x USB3.0 (P5) H310:1x USB2.0 (P5)'.\n*   **SPI/Fan/Management:**\n    *   'SPI 0/1 Header' connects via 'SPI 0/1' (contains 'SPI 0 Socket' and 'SPI 1 Socket').\n    *   'CPU Fan', 'System Fan 1', and 'System Fan 2' are listed on the right.\n    *   'BMC STM32L071' connects via 'SMBus' to the chipset and 'I2C & GPIO' to 'Sensor MAX6642'.\n    *   'Feature Connector' connects via 'System Signals'.](.amitx-cf-g-50m-00093-1000-20/e86cf44436c075ba6353ae9dd76954556c078592ca52aba00234fbd2b1f97cde.jpg)

Figure 1: AmITX-CF-G Functional Block Diagram

Note: Full-size Mini-PCIe slot (Q370: PCIe x1, mSATA and USB 2.0 / H310: PCIe x1)

This page intentionally left blank.

# 3. Mechanical Layout

# 3.1. Connector Locations

# 3.1.1. Rear I/O Connectors

![DP\nUSB 3.0\nDP\nUSB 3.0\nDP\nUSB 2.0\nLAN 1\nLAN 2\nAudio](.amitx-cf-g-50m-00093-1000-20/97fc0eb4faf53bc83f49e9b711b17de17d433ddb014ed1e9df69ce8acf5efe8e.jpg)

Figure 2: AmITX-CF-G Rear I/O

# 3.1.2. Component-Side Connectors

![Audio Header\nPCIe x16\nPCIe x1\nSATA Power Con.\nSPI Header\nSPI 1 Socket\nSPI 0 Socket\n2x USB3.0 for Q370\n1x USB2.0 for H310\n1x RS-232/422/485\n(SER 1)\nDB40 Connector\nSystem Fan Con.\n1x RS-232 (SER 2)\n1x RS-232 (SER 3)\n1x RS-232 (SER 4)\n2x RS-232/CCTalk\n(SER 5&6)\nCPU Fan\nMini PCIe / mSATA\nSATA1/2/3\nM.2 (M Key)\nUSB Vertical Connector\nUSB 3.0 for Q370\nUSB 2.0 for H310\n2x DDR4 SODIMM\nFeature Header\nFront Panel Header\nATX/AT Power](.amitx-cf-g-50m-00093-1000-20/35ff64092e6d50341574587a10fda09436d2020576036c2e00e95f8b333fd1bb.jpg)

Figure 3: AmITX-CF-G Component-Side Connectors

# 3.2. Mechanical Dimensions

Top View
![This image is a technical schematic diagram of a square computer motherboard, featuring a top-down view and a side profile view.\n\n**Top View:**\nThe largest section shows the layout of the motherboard.\n*   **Dimensions:** Vertical and horizontal dimension lines indicate the board measures **170** by **170**.\n*   **Components:**\n    *   A large, square CPU socket is positioned centrally on the right side.\n    *   Two vertical RAM slots are located on the left side.\n    *   A long PCIe expansion slot runs horizontally along the top edge.\n    *   Various pin headers, power connectors (including a 24-pin and 8-pin connector on the left edge), and small component clusters are distributed across the surface.\n    *   A column of I/O ports is situated along the right edge.\n\n**Side View:**\nLocated at the bottom, labeled **Side View**.\n*   This profile view shows the physical height of components like the CPU socket and I/O ports relative to the board.\n*   **Dimensions:** Vertical lines on the right indicate a total height of **35.33** and a board thickness of **1.60**.\n\n**Text:**\nThe text **Dimensions: mm** appears centered at the very bottom.](.amitx-cf-g-50m-00093-1000-20/fe67f85b6bda16f2a5f747d1724e808ceb28d2860dc12c090a3dc11d8be7a48c.jpg)
Figure 4: AmITX-CF-G Mechanical Dimensions

# 3.3. Thermal Solutions

<table><tr><td>LGA1150 CPU Cooler, H=59.52mm, for 35W TPD CPUP/N: 32-20581-0000Standard Temp.: 0°C to 60°C</td><td>&lt;img src="images/009170c8692ed0a6aa43b066517b1f7cbff616978ac3c29ea98083029fab7f4a.jpg"/&gt; &lt;img src="images/56bff8c341ed9e5a92feec7f813e1502b872acd1778565fb2f2e75e31ae0c549.jpg"/&gt;</td></tr><tr><td rowspan="2">LGA1150 CPU Cooler, H=65.6 mm, for 54W ~ 65W TDP CPUP/N: 32-20818-1000-A0Standard Temp.: 0°C to 60°C</td><td>&lt;img src="images/d15ef858270340b91fdd94dcbe015aa5bb9087a8f41a1bbef6c9827967d6dcee.jpg"/&gt; &lt;img src="images/9ef7109ae27ea853ec9aec98e3e9e485500727c77702ae90955c6ae51a47ae97.jpg"/&gt;</td></tr><tr><td>&lt;img src="images/5672643664c929d07a768b170ed12ad89c7c864a7c02aaa2368771f93f28bda7.jpg"/&gt;</td></tr><tr><td colspan="2">NOTICE: Risk of damage!These coolers are designed for the ADi-SAXX Box PC (worst case), and thermal performance will change with differences in cabinet spaces. In no event may the chassis ventilation holes be obstructed. Always ensure that sufficient clearance (at least 50 mm to each direction except fo the base) exists around the cooling vents for unrestricted airflow.Failure to comply with this instruction could result in damage to the ADi-SAXX or AmITX-CF-G.</td></tr></table>

This page intentionally left blank.

# 4. Connectors and Jumpers

See Section 3.1 Connector Locations

# 4.1. Rear IO Connectors

# 4.1.1. DisplayPort Connectors

Three DisplayPort v1.2 specification connectors up to 3840x2160 @ 60 Hz

<table><tr><td>Pin #</td><td>Signal</td><td>Pin #</td><td>Signal</td></tr><tr><td>1</td><td>CN_DP0_P</td><td>2</td><td>Ground</td></tr><tr><td>3</td><td>CN_DP0_N</td><td>4</td><td>CN_DP1_P</td></tr><tr><td>5</td><td>Ground</td><td>6</td><td>CN_DP1_N</td></tr><tr><td>7</td><td>CN_DP2_P</td><td>8</td><td>Ground</td></tr><tr><td>9</td><td>CN_DP2_N</td><td>10</td><td>CN_DP3_P</td></tr><tr><td>11</td><td>Ground</td><td>12</td><td>CN_DP3_N</td></tr><tr><td>13</td><td>CN_CAD-L</td><td>14</td><td>CN_CEC</td></tr><tr><td>15</td><td>CN_AUX_P</td><td>16</td><td>Ground</td></tr><tr><td>17</td><td>CN_AUX_N</td><td>18</td><td>DDP_HPD</td></tr><tr><td>19</td><td>Ground</td><td>20</td><td>P3V3</td></tr></table>

![The image displays a technical line drawing of a 20-pin connector. It features two parallel vertical columns of square pins. The left column is labeled with the number '**1**' at the top and '**19**' near the bottom. The right column is labeled with the number '**2**' at the top and '**20**' near the bottom. The connector housing has small rectangular protrusions on the left and right sides, an '**L**'-shaped alignment key at the top, and a small rectangular feature at the bottom center.](.amitx-cf-g-50m-00093-1000-20/110920facbb156a91e898cf3fbfb828369e3b6ccf4faccb5aa03f8d3c32bd640.jpg)

# 4.1.2. Ethernet Connectors (LAN1, LAN2)

Dual 10/100/1000Mbit/s LAN Ethernet controllers based on Realtek RTL8119-CG, supporting PXE and WOL over both LANs.

<table><tr><td>Pin #</td><td>10BASE-T/100BASE-TX</td><td>1000BASE-T</td></tr><tr><td>1</td><td>TX+</td><td>LAN_MDI0+</td></tr><tr><td>2</td><td>TX-</td><td>LAN_MDI0-</td></tr><tr><td>3</td><td>RX+</td><td>LAN_MDI1+</td></tr><tr><td>4</td><td>--</td><td>LAN_MDI2+</td></tr><tr><td>5</td><td>--</td><td>LAN_MDI2-</td></tr><tr><td>6</td><td>RX-</td><td>LAN_MDI1-</td></tr><tr><td>7</td><td>--</td><td>LAN_MDI3+</td></tr><tr><td>8</td><td>--</td><td>LAN_MDI3-</td></tr></table>

![The image displays a schematic diagram of an RJ45 connector. At the top, the text 'LED1' is on the left and 'LED2' is on the right. At the bottom, the number '8' is on the left and '1' is on the right. The central graphic depicts the connector housing with pin contacts.](.amitx-cf-g-50m-00093-1000-20/44ca403272ed83a200eb901596940705efd723e8dd04fbb58fb160e50962b789.jpg)

<table><tr><td colspan="2">LED1 (Link/Activity)</td><td colspan="2">LED2 (Speed)</td></tr><tr><td>Status</td><td>Description</td><td>Status</td><td>Description</td></tr><tr><td>Off</td><td>No Link</td><td>Off</td><td>10 Mb connection</td></tr><tr><td>Green</td><td>Link</td><td>Orange</td><td>100 Mb connection</td></tr><tr><td>Orange</td><td>Data Activity</td><td>Blinking</td><td>1 Gb connection</td></tr></table>

# 4.1.3. USB Connectors

4x USB 3.0, 4x USB 2.0

5V supply for external devices
 5Vsb is supplied during power down to allow wakeup on USB device activity during S3\~S4 state
 For USB 2.0 port: 1A for device power supply protected by a resettable 1.5A fuse
 For USB 3.1 port: 1.8A for device power supply protected by a resettable 2.6A fuse

<table><tr><td>Pin #</td><td>Signal</td></tr><tr><td>1</td><td>VCC</td></tr><tr><td>2</td><td>UV0-</td></tr><tr><td>3</td><td>UV0+</td></tr><tr><td>4</td><td>GND</td></tr></table>

![A black and white line drawing of a dual inline package (DIP) integrated circuit. The component has a rectangular body with rounded corners and two rows of pins extending from the left and right sides. On the right side, numbers are printed vertically next to the pins: '4', '3', '2', and '1' from top to bottom. A small semicircular notch is visible at the top left corner of the package to indicate pin 1.](.amitx-cf-g-50m-00093-1000-20/b32c550c0e8838fb36e6f22401d655f8e73127aa436218a5e168352f68027590.jpg)

<table><tr><td>Pin #</td><td>Signal</td></tr><tr><td>1</td><td>USB3.0_P5VA</td></tr><tr><td>2</td><td>USB2_CMAN</td></tr><tr><td>3</td><td>USB2_CMAP</td></tr><tr><td>4</td><td>GND</td></tr><tr><td>5</td><td>USB3A_CMRXN</td></tr><tr><td>6</td><td>USB3A_CMRXP</td></tr><tr><td>7</td><td>GND</td></tr><tr><td>8</td><td>USB3A_CMTXN</td></tr><tr><td>9</td><td>USB3A_CMTXP</td></tr></table>

![1\n2\n3\n4\n5\n6\n7\n8\n9](.amitx-cf-g-50m-00093-1000-20/abafc7ef15800bc3e8fca422a274b11b597a724ceb030151365f359ac31cefbd.jpg)

# 4.1.4. Audio Connectors

• 7.1 channel audio via 5 jacks and S/PDIF output on rear I/O
Realtek ALC888 codec

# 4.2. Internal Connectors

# 4.2.1. ATX Power Connector (ATX\_PWR, proprietary)

AmITX-CF-G supports a proprietary internal ATX Power Connector (ATX\_PWR). An adapter cable is provided for conection to a standard ATX power supply.

<table><tr><td>Pin #</td><td>Signal</td><td>Pin #</td><td>Signal</td></tr><tr><td>1</td><td>SB5V</td><td>8</td><td>P_OK</td></tr><tr><td>2</td><td>GND</td><td>9</td><td>PS_ON#</td></tr><tr><td>3</td><td>GND</td><td>10</td><td>+12V</td></tr><tr><td>4</td><td>GND</td><td>11</td><td>+12V</td></tr><tr><td>5</td><td>GND</td><td>12</td><td>+12V</td></tr><tr><td>6</td><td>GND</td><td>13</td><td>+12V</td></tr><tr><td>7</td><td>3.3V</td><td>14</td><td>+5V</td></tr></table>

![CN POK ATX\n8\n1\nP5VSB\nCN PS ON-L\n9\n2\nP12V_ATX\n10\n3\n11\n4\n12\n5\n13\n6\n14\n7\n22uF 16V\nP5V_ATX\n100ohm +/-5%\n100ohm +/-5%\n100ohm +/-5%\nP3V3_ATX\n100ohm +/-5%\n100ohm +/-5%\n100ohm +/-5%](.amitx-cf-g-50m-00093-1000-20/d86495446b004e819301bdb7d37db3762da44bb244de482a501fc12c02277e70.jpg)

ATX Adapter Cable: ADLINK Part. No. 30-20872-1000 (length 250 mm)
![Motherboard\nATX Power\nConnector\n(ATX_PWR)\nATX Power\nSupply](.amitx-cf-g-50m-00093-1000-20/cc6fe57a0d7b000b4093c152be96e873a01c3ce842a8b1844f9e409b6a6e2dbd.jpg)

# 4.2.2. SATA Connectors (SATA1/2/3)

Three SATA 6 Gbps ports are available on the AmITX-CF-G.

Option function: Jumper select NA/3.3V/5V for SATA1 and SATA2 to deliver power by SATA pin 7; default is NA.

<table><tr><td>Pin #</td><td>Signal</td></tr><tr><td>1</td><td>GND</td></tr><tr><td>2</td><td>TXP</td></tr><tr><td>3</td><td>TXN</td></tr><tr><td>4</td><td>GND</td></tr><tr><td>5</td><td>RXN</td></tr><tr><td>6</td><td>RXP</td></tr><tr><td>7</td><td>N/A(default),(option)SATA1/2SATA DOMPWR</td></tr></table>

![This image displays a black and white technical line drawing of a vertical rectangular component. Inside the main outline is a long, narrow vertical channel running down the center. Within this channel is a vertical dashed line composed of alternating black rectangular segments and white spaces. On the left wall of the channel, there is a small horizontal rectangular protrusion. Small rectangular features are visible at the top and bottom ends of the inner channel. To the right of the drawing, the number '1' is positioned near the top section, and the number '7' is positioned near the bottom section.](.amitx-cf-g-50m-00093-1000-20/ccb291d3bc982fea7c1ba505782d77c82bc900cdd4a6c3dbb4d0fb0e869e09dc.jpg)

# 4.2.3. SATA Power Connectors (ST\_PWR1/2)

Two 5-pin SATA power connectors for SATA drive power cable.

<table><tr><td>Pin #</td><td>Signal</td></tr><tr><td>1</td><td>12V</td></tr><tr><td>2</td><td>GND</td></tr><tr><td>3</td><td>5V</td></tr><tr><td>4</td><td>GND</td></tr><tr><td>5</td><td>3.3V</td></tr></table>

![The image shows a black-and-white line drawing of a connector. At the top, the numbers '5 4 3 2 1' are arranged horizontally. Below the numbers is a large rectangular outline containing five small square holes spaced evenly in a row. Beneath the main rectangle are small rectangular shapes representing the connector's pins.](.amitx-cf-g-50m-00093-1000-20/9eec1eda13220d2ccd6e5c2c0bef36a40450f8a882df231c5f8f8e4e839d520e.jpg)

SATA Power Cable: ADLINK Part. No.: 30-20875-0000 (length 200 mm)

![Based on the provided image, here is an accurate description of the flowchart/block diagram:\n\n**Labeled Blocks:**\n*   **Left:** A label reading 'HDD/SSD Power' next to a large arrow pointing to the left.\n*   **Top Right:** A label reading 'HDD/SSD Power' next to a large arrow pointing to the right.\n*   **Bottom Right:** A label reading 'Motherboard SATA Power Connector' next to a large arrow pointing to the right.\n\n**Connections:**\n*   **Central Component:** In the center is a 4-pin connector block.\n*   **Branching Lines:** Multiple lines (representing cables) extend from the central connector to the right, splitting into two groups:\n    *   One group connects the central block to the top-right connector block.\n    *   Another group connects the central block to the bottom-right connector block.](.amitx-cf-g-50m-00093-1000-20/a75eb89328d1fe91d405fa9c249a982f0279153e888b2e8003b370430254835a.jpg)

![Coiled black and yellow plastic electrical connector with terminal connectors (no text or symbols visible)](.amitx-cf-g-50m-00093-1000-20/b515fab7a835b4b29a82ae1853d6f237e99c81036d33218084620ee965ed2ef1.jpg)

# 4.2.4. USB Headers

5V/SB5V: 5V supplies for external devices. SB5V is supplied during power-down to allow wakeup on USB device activity during S3\~S4 state.

H310: 1xUSB2.0:

<table><tr><td>Pin #</td><td>Signal</td><td>Pin #</td><td>Signal</td></tr><tr><td>1</td><td>USB2_10_14_PWR</td><td>2</td><td>USB2_10_14_PWR</td></tr><tr><td>3</td><td>NC</td><td>4</td><td>USB2_P14</td></tr><tr><td>5</td><td>NC</td><td>6</td><td>USB2_N14</td></tr><tr><td>7</td><td>GND</td><td>8</td><td>GND</td></tr><tr><td>9</td><td>KEY</td><td>10</td><td>NC</td></tr></table>

![1\n10](.amitx-cf-g-50m-00093-1000-20/f2407988830879aa7618f197275775a7c47855a82deaa9a4a306384f48ed3573.jpg)

# USB Cable (optional):

USB 2.0 Header to 2x Female Type-A Cable (length 200mm), P/N: 30-20874-1000

![Diagram of two connected electrical connectors with wires, no text or symbols present](.amitx-cf-g-50m-00093-1000-20/2a74b661b79229ee7cc67c70b99dab18e5cc26a50c780c73830788dc36bb7bf2.jpg)

Q370: 2xUSB3.0:

<table><tr><td>Pin #</td><td>Signal</td><td>Pin #</td><td>Signal</td></tr><tr><td>1</td><td>NC</td><td>20</td><td>Key</td></tr><tr><td>2</td><td>USB3_TX_P7</td><td>19</td><td>USB3_TX_P8</td></tr><tr><td>3</td><td>USB3_TX_N7</td><td>18</td><td>USB3_TX_N8</td></tr><tr><td>4</td><td>GND</td><td>17</td><td>GND</td></tr><tr><td>5</td><td>USB3_RX_P7</td><td>16</td><td>USB3_RX_P8</td></tr><tr><td>6</td><td>USB3_RX_N7</td><td>15</td><td>USB3_RX_N8</td></tr><tr><td>7</td><td>GND</td><td>14</td><td>GND</td></tr><tr><td>8</td><td>USB2_P10</td><td>13</td><td>USB2_P14</td></tr><tr><td>9</td><td>USB2_N10</td><td>12</td><td>USB2_N14</td></tr><tr><td>10</td><td>USB2_10_14_PWR</td><td>11</td><td>USB2_10_14_PWR</td></tr></table>

![Pure diagram of a rectangular structure with internal compartments and numbered labels (1 and 20), no text or symbols present.](.amitx-cf-g-50m-00093-1000-20/f0cc5769f7d72890fc71eaa1ada71e6e5580698f8d138e632251527483a20805.jpg)

# USB Cable (optional):

USB 3.0 Header to 2x Female Type-A Cable (length 200mm), P/N: 30-20963-0000

![Pure electrical connector diagram showing two connected components with no text or symbols](.amitx-cf-g-50m-00093-1000-20/d732e5a476c9383b150f015e711d06d38d4b72af3e62c342f24bbc609a09a469.jpg)

# 4.2.5. Audio Header

2x13-pin 2.0 pitch standard wafer connector

Note: Signals shared with Audio Header on Rear I/O

<table><tr><td>Signal</td><td>Pin #</td><td>Pin #</td><td>Signal</td></tr><tr><td>LFE-OUT</td><td>1</td><td>2</td><td>CEN-OUT</td></tr><tr><td>AAGND</td><td>3</td><td>4</td><td>AAGND</td></tr><tr><td>FRONT-OUT-L</td><td>5</td><td>6</td><td>FRONT-OUT-R</td></tr><tr><td>AAGND</td><td>7</td><td>8</td><td>AAGND</td></tr><tr><td>REAR-OUT-L</td><td>9</td><td>10</td><td>REAR-OUT-R</td></tr><tr><td>SIDE-OUT-L</td><td>11</td><td>12</td><td>SIDE-OUT-R</td></tr><tr><td>AAGND</td><td>13</td><td>14</td><td>AAGND</td></tr><tr><td>MIC1-L</td><td>15</td><td>16</td><td>MIC1-R</td></tr><tr><td>AAGND</td><td>17</td><td>18</td><td>AAGND</td></tr><tr><td>LINE1-L</td><td>19</td><td>20</td><td>LINE1-R</td></tr><tr><td>MUTE</td><td>21</td><td>22</td><td>AAGND</td></tr><tr><td>GND</td><td>23</td><td>24</td><td>NC</td></tr><tr><td>SPDIF-OUT</td><td>25</td><td>26</td><td>GND</td></tr></table>

![Pure electrical connector pinout diagram without any text or symbols](.amitx-cf-g-50m-00093-1000-20/ad748e54e4f8acbe0b40cdeaf68ef17349e5f0d612ca4032032ef18a76dd6922.jpg)

# 4.2.6. CPU Fan and System Fan Connectors

Pins 3 and 4 are connected (monitored and managed) by SEMA controller.

<table><tr><td>Pin #</td><td>Signal</td></tr><tr><td>1</td><td>GND</td></tr><tr><td>2</td><td>Fan Power (+12V)</td></tr><tr><td>3</td><td>Fan Sense</td></tr><tr><td>4</td><td>Fan Speed Control</td></tr></table>

4
![The image displays a black-and-white wireframe sketch of a website layout. It features a top navigation bar with vertical dividers, a large rectangular header space, a main section with a sidebar on the left and a larger content area on the right, and a row of six square placeholders below. The text 'P O R T F O L I O' is written in spaced-out capital letters across the lower section.](.amitx-cf-g-50m-00093-1000-20/8d68a12eea8b3b246352013af0cc44e93255b14be2401d5ae6d5cf671716374a.jpg)
1

# 4.2.7. Serial COM Port Connectors

Six internal Serial Ports (SER1-6)

<table><tr><td>Serial Port</td><td>Functions</td></tr><tr><td>SER1</td><td>Supports RS-232 / RS-422 / RS-485, 5V/12V power support by jumper select (JPS3P, default NC).SWS1M: Switch for mode selection of SER1 (default RS-232).</td></tr><tr><td>SER2</td><td>Supports only RS-232</td></tr><tr><td>SER3</td><td>Supports only RS-232</td></tr><tr><td>SER4</td><td>Supports only RS-232</td></tr><tr><td>SER5-6</td><td>Supports RS-232 with CTS# RTS# or ccTalk via one physical connector</td></tr></table>

![The image shows a schematic diagram of a dual in-line package (DIP) integrated circuit. A thick black rectangular outline encloses ten small squares arranged in two vertical columns of five. Outside the rectangle, numbers indicate pin positions: '1' is at the top left, '2' is at the top right, '9' is at the bottom left, and '10' is at the bottom right. Small gaps in the left border of the rectangle appear near the numbers 1 and 9.](.amitx-cf-g-50m-00093-1000-20/c2af8712a1fd9f4ef7f1011c2b7439f29083bffe58721d8fd00edcd1120aec50.jpg)

RS-232

<table><tr><td>Pin #</td><td>Signal</td><td>Pin #</td><td>Signal</td></tr><tr><td>1</td><td>DCD</td><td>2</td><td>DSR</td></tr><tr><td>3</td><td>RxD</td><td>4</td><td>RTS</td></tr><tr><td>5</td><td>TxD</td><td>6</td><td>CTS</td></tr><tr><td>7</td><td>DTR</td><td>8</td><td>RI</td></tr><tr><td>9</td><td>GND</td><td>10</td><td>5V / 12V</td></tr></table>

RS-422 (SER1 only)

<table><tr><td>Pin #</td><td>Signal</td><td>Pin #</td><td>Signal</td></tr><tr><td>1</td><td>Tx-</td><td>2</td><td>—</td></tr><tr><td>3</td><td>Tx+</td><td>4</td><td>—</td></tr><tr><td>5</td><td>Rx+</td><td>6</td><td>—</td></tr><tr><td>7</td><td>Rx-</td><td>8</td><td>—</td></tr><tr><td>9</td><td>GND</td><td>10</td><td>5V / 12V</td></tr></table>

RS-485 (SER1 only)

<table><tr><td>Pin #</td><td>Signal</td><td>Pin #</td><td>Signal</td></tr><tr><td>1</td><td>Tx/Rx-</td><td>2</td><td>—</td></tr><tr><td>3</td><td>Tx/Rx+</td><td>4</td><td>—</td></tr><tr><td>5</td><td>—</td><td>6</td><td>—</td></tr><tr><td>7</td><td>—</td><td>8</td><td>—</td></tr><tr><td>9</td><td>GND</td><td>10</td><td>5V / 12V</td></tr></table>

RS-232 (SER5\_6 only)

<table><tr><td>Pin #</td><td>Signal</td><td>Pin #</td><td>Signal</td></tr><tr><td>1</td><td>RxD5</td><td>2</td><td>RTS5</td></tr><tr><td>3</td><td>TxD5</td><td>4</td><td>CTS5</td></tr><tr><td>5</td><td>GND</td><td>6</td><td>GND</td></tr><tr><td>7</td><td>RxD6</td><td>8</td><td>RTS6</td></tr><tr><td>9</td><td>TxD6</td><td>10</td><td>CTS6</td></tr></table>

ccTalk (SER5\_6 only)

<table><tr><td>Pin #</td><td>Signal</td><td>Pin #</td><td>Signal</td></tr><tr><td>1</td><td>ccTalk_RX5</td><td>2</td><td>—</td></tr><tr><td>3</td><td>ccTalk_TX5</td><td>4</td><td>—</td></tr><tr><td>5</td><td>GND</td><td>6</td><td>GND</td></tr><tr><td>7</td><td>ccTalk_RX6</td><td>8</td><td>—</td></tr><tr><td>9</td><td>ccTalk_TX6</td><td>10</td><td>—</td></tr></table>

SER1 Mode Switch (SWS1M)

<table><tr><td colspan="4">SWS1M (SER1 Mode Select)</td></tr><tr><td></td><td>RS-232 (default)</td><td>RS-422</td><td>RS-485</td></tr><tr><td>1</td><td>ON</td><td>ON</td><td>OFF</td></tr><tr><td>2</td><td>OFF</td><td>ON</td><td>ON</td></tr></table>

Note: See Section 4.3 COM Port (SER1) Mode Selection (SWS1M). Use JPS1P for SER1 power selection.

SER5-6 Mode Select (JPS5M1/ JPS5M2 ; JPS6M1/ JPS6M2)

<table><tr><td colspan="2">SER5-6 Mode Select</td></tr><tr><td>RS-232 (default)</td><td>ccTalk</td></tr><tr><td>1-3</td><td>3-5</td></tr><tr><td>2-4</td><td>4-6</td></tr></table>

# COM Cable (optional):

COM Port Cable (length 250mm), P/N: 30-20876-0000

![The image is a line drawing of a DB9 serial connector. It shows a rectangular outer frame with a hexagonal nut at the top and bottom. Inside is a smaller rectangle containing nine dots arranged in three rows: four dots on the top row, one dot in the center, and four dots on the bottom row. The numbers '1', '5', '6', and '9' are printed near the corners of the inner rectangle.](.amitx-cf-g-50m-00093-1000-20/e494cba6a3ce10d947b9be0bba23180cb1242a6f0604959b82f36afe31d56a3e.jpg)

![Diagram of a USB cable connector showing internal twisted and terminal connections (no text or labels)](.amitx-cf-g-50m-00093-1000-20/536e1d1f218d48700be2d47e7b5e5833ce22c42dce75ac8e94dcd13b9d9e6da3.jpg)

# 4.2.8. Front Panel Header

2x12-pin 2.0 pitch standard wafer connector

The front panel connector provides Audio Mic-In / Line Out, ATX power switch, Reset, HDD LED, and SUS LED (System Power LED).

<table><tr><td>Pin #</td><td>Signal</td><td>Ioh/ lol</td><td>Type</td><td>Note</td><td>Pin #</td><td>Signal</td><td>Type</td><td>Ioh/ lol</td><td>Note</td></tr><tr><td>1</td><td>N/A</td><td>-</td><td></td><td></td><td>2</td><td>N/A</td><td></td><td>-</td><td></td></tr><tr><td>3</td><td>N/A</td><td>-</td><td></td><td></td><td>4</td><td>N/A</td><td></td><td>-</td><td></td></tr><tr><td>5</td><td>N/A</td><td>-</td><td></td><td></td><td>6</td><td>N/A</td><td></td><td>-</td><td></td></tr><tr><td>7</td><td>GND</td><td>-</td><td>PWR</td><td></td><td>8</td><td>GND</td><td>PWR</td><td>-</td><td></td></tr><tr><td>9</td><td>Mute</td><td>-</td><td>Mute</td><td></td><td>10</td><td>LINE2-L</td><td></td><td>-</td><td></td></tr><tr><td>11</td><td>+5V</td><td>-</td><td>PWR</td><td>1</td><td>12</td><td>+5V</td><td>PWR</td><td>-</td><td>1</td></tr><tr><td>13</td><td>SATA_LED#</td><td>25/25mA</td><td>O</td><td></td><td>14</td><td>SUS_LED</td><td>O</td><td></td><td>2</td></tr><tr><td>15</td><td>GND</td><td>-</td><td>PWR</td><td></td><td>16</td><td>PWRBTN_IN#</td><td>I</td><td></td><td></td></tr><tr><td>17</td><td>RSTIN#</td><td>-</td><td>I</td><td></td><td>18</td><td>GND</td><td>PWR</td><td>-</td><td></td></tr><tr><td>19</td><td>SB3V3</td><td>-</td><td>PWR</td><td></td><td>20</td><td>LINE2-R</td><td></td><td>-</td><td></td></tr><tr><td>21</td><td>AGND</td><td>-</td><td>PWR</td><td></td><td>22</td><td>AGND</td><td>PWR</td><td>-</td><td></td></tr><tr><td>23</td><td>MIC2-L</td><td>-</td><td>AI</td><td></td><td>24</td><td>MIC2-R</td><td>AI</td><td>-</td><td></td></tr></table>

![The image displays a diagram of a connector housing labeled with the number **1** on the left and the number **2** on the right. The housing is a vertical rectangle containing a central array of two columns of square holes. Flanking this central array are single columns of rectangular slots along the inner left and right sides. Additional mounting slots are present along the outer left and right edges and at the bottom center.](.amitx-cf-g-50m-00093-1000-20/60fd2cfbb8864369c49e1ab5a542a208d854040ed560203db759ae0f0f5901c3.jpg)
Note 1: Maximum load is 1A.
Note 2: Connect SUS\_LED (System Power LED) to the power status indicator on the chassis front panel. The LED is on when the system is operating. The LED keeps blinking when the system is in S1/S3 sleep state. The LED is off when the system is in S4 sleep state or powered off (S5).

# 4.2.9. Feature Header

2x14-pin 2.0 pitch standard wafer connector

The feature connector provides Case Open, I2C, SMBus, and GPIO (10pin).

<table><tr><td>Signal</td><td>Description</td></tr><tr><td>TEMPS</td><td>Analogue temp sensor, connect to analog input of BMC</td></tr><tr><td>EXT_BAT</td><td>Connect to RTC power</td></tr><tr><td>CASE_OPEN#</td><td>Any time case open occurs, system will notice/show case open alert in POST during the next boot.</td></tr><tr><td>I2CC / I2CD</td><td>Connect to BMC (I2C Master)</td></tr><tr><td>I2C</td><td>SEMA</td></tr></table>

![Pure electrical connector pinout diagram without any text or symbols](.amitx-cf-g-50m-00093-1000-20/3e126a2ebc826331cb8896377bf3ae89ed3c3f5ca205c3010cd764dbaedcc6ea.jpg)

<table><tr><td>Pin #</td><td>Signal</td><td>Pull U/D</td><td>IOH/IOL</td><td>Type</td><td>Note</td><td>Pin #</td><td>Signal</td><td>Type</td><td>IOH/IOL</td><td>Pull U/D</td><td>Note</td></tr><tr><td>1</td><td>CASE_OPEN#</td><td>PU 2M</td><td>-</td><td>I</td><td></td><td>2</td><td>SMBC</td><td>OT</td><td>/4mA</td><td>PU 10K</td><td>1</td></tr><tr><td>3</td><td>GND</td><td>-</td><td>-</td><td>PWR</td><td></td><td>4</td><td>SMBD</td><td>OT</td><td>/4mA</td><td>PU 10K</td><td>1</td></tr><tr><td>5</td><td>TEMPS</td><td>-</td><td></td><td>I</td><td>2</td><td>6</td><td>I2CC</td><td>OT</td><td>-</td><td>PU 10K</td><td>1</td></tr><tr><td>7</td><td>EXT_BAT</td><td>-</td><td></td><td>PWR</td><td></td><td>8</td><td>I2CD</td><td>OT</td><td>-</td><td>PU 10K</td><td>1</td></tr><tr><td>9</td><td>SB3V3</td><td>-</td><td>-</td><td>PWR</td><td></td><td>10</td><td>5V</td><td>PWR</td><td>-</td><td>-</td><td></td></tr><tr><td>11</td><td>GND</td><td>-</td><td>-</td><td>PWR</td><td></td><td>12</td><td>GND</td><td>PWR</td><td>-</td><td>-</td><td></td></tr><tr><td>13</td><td>GPIO0</td><td>-</td><td>PU10K3V3</td><td>IOT</td><td></td><td>14</td><td>GPIO1</td><td>IOT</td><td></td><td>PU10K3V3</td><td></td></tr><tr><td>15</td><td>GPIO2</td><td>-</td><td>PU10K3V3</td><td>IOT</td><td></td><td>16</td><td>GPIO3</td><td>IOT</td><td></td><td>PU10K3V3</td><td></td></tr><tr><td>17</td><td>GPIO4</td><td>-</td><td>PU10K3V3</td><td>IOT</td><td></td><td>18</td><td>GPIO5</td><td>IOT</td><td></td><td>PU10K3V3</td><td></td></tr><tr><td>19</td><td>GPIO6</td><td>-</td><td>PU10K3V3</td><td>IOT</td><td></td><td>20</td><td>GPIO7</td><td>IOT</td><td></td><td>PU10K3V3</td><td></td></tr><tr><td>21</td><td>GPIO8</td><td></td><td>PU10K3V3</td><td>IOT</td><td></td><td>22</td><td>GPIO9</td><td>IOT</td><td></td><td>PU10K3V3</td><td></td></tr><tr><td>23</td><td>GND</td><td>-</td><td></td><td>PWR</td><td></td><td>24</td><td>SUS_S3#</td><td>O</td><td>25/25mA</td><td>-</td><td></td></tr><tr><td>25</td><td>12V</td><td>-</td><td>-</td><td>PWR</td><td></td><td>26</td><td>SUS_S4#</td><td>O</td><td>25/25mA</td><td>-</td><td></td></tr><tr><td>27</td><td>PWR_OK</td><td>-</td><td>25/25mA</td><td>O</td><td></td><td>28</td><td>SUS_S5#</td><td>O</td><td>25/25mA</td><td>-</td><td></td></tr></table>

Note 1: Pull-up to +3V3Dual (+3V3 or SB3V3).
Note 2: Input to SEMA.

# 4.2.10. SPI Header

2x6-pin 2.0 pitch standard wafer connector

<table><tr><td>Type</td><td>Signal</td><td>Pin #</td><td>Pin #</td><td>Signal</td><td>Type</td></tr><tr><td></td><td>CLK</td><td>1</td><td>2</td><td>SB3V3</td><td>PWR</td></tr><tr><td>I</td><td>CS0#</td><td>3</td><td>4</td><td>ADDIN</td><td>IO</td></tr><tr><td>I</td><td>CS1#</td><td>5</td><td>6</td><td>NC</td><td>-</td></tr><tr><td>I</td><td>MOSI</td><td>7</td><td>8</td><td>ISOLATE</td><td>IO</td></tr><tr><td>O</td><td>MISO</td><td>9</td><td>10</td><td>GND</td><td>PWR</td></tr><tr><td>IO</td><td>SPI_IO2_#WP</td><td>11</td><td>12</td><td>SPI_IO3_#HOLD</td><td>IO</td></tr></table>

1
![The image displays a black-and-white architectural floor plan of a long, rectangular building. The design features a central, open atrium or hall area surrounded by a perimeter of corridors and rooms. Within the large central white space, there is a precise grid of 50 solid black squares arranged in 5 columns and 10 rows. The perimeter structure consists of thick black lines forming walls and partitions, with various irregular room shapes along the edges and distinct protrusions on the left side. The entire diagram is enclosed within a thick, irregular black border. There is no visible text in the image.](.amitx-cf-g-50m-00093-1000-20/1aacebba78c6519bbae790a4717c5b883fb96ff5fd33a0d98fae89af3810b0ad.jpg)
2

<table><tr><td>Signal</td><td>Description</td></tr><tr><td>CLK</td><td>Serial Clock</td></tr><tr><td>SB3V3</td><td>3.3V Standby Voltage power line. Normally output power, but when Motherboard is turned off then the on-board SPI Flash can be 3.3V power sourced via this pin.</td></tr><tr><td>CS0#</td><td>CS0# Chip Select 0, active low.</td></tr><tr><td>ADDIN</td><td>ADDIN input signal must be NC.</td></tr><tr><td>MOSI</td><td>Master Output, Slave Input</td></tr><tr><td>ISOLATE#</td><td>The ISOLATE# input, active low, is normally NC, but must be connected to GND when loading SPI flash. Power Supply to the Motherboard must be turned off when loading SPI flash. The pull up resistor is connected via diode to 5VSB.</td></tr><tr><td>MISO</td><td>Master Input, Slave Output</td></tr><tr><td>SPI_IO2_#WP</td><td>SPI Data I/O: A bidirectional signal used to support the new Dual IO Fast Read, Quad IO Fast Read and Quad Output Fast Read modes. This signal is not used in Dual Output Fast Read mode.</td></tr><tr><td>SPI_IO3_#HOLD</td><td>SPI Data I/O: A bidirectional signal used to support the new Dual IO Fast Read, Quad IO Fast Read and Quad Output Fast Read modes. This signal is not used in Dual Output Fast Read mode.</td></tr></table>

# 4.2.11. DB40 Debug Connector

FPC Connector Type: FCI 59GF Flex 10042867

![Close-up of a green printed circuit board with black connectors and white plastic caps (no visible text or symbols)](.amitx-cf-g-50m-00093-1000-20/64d8da36c9d333ab46b7d8b66b619727ab4702011d982dcd620b681ade75dff6.jpg)

1

40

<table><tr><td>Pin</td><td>Interface</td><td>Signal</td><td>Remark</td><td>Pin</td><td>Interface</td><td>Signal</td><td>Remark</td></tr><tr><td>40</td><td rowspan="7">SPI Program interface</td><td>VCC_SPI_IN</td><td>SPI Power Input from flash tool to module. HW need add MOS FET to switch SPI power for SPI ROM</td><td>20</td><td rowspan="8">BMC Program interface (continued)</td><td>TXD6</td><td></td></tr><tr><td>39</td><td>GND</td><td></td><td>19</td><td>RXD6</td><td></td></tr><tr><td>38</td><td>SPI_BIOS_CS0#</td><td></td><td>18</td><td>FUMD0</td><td></td></tr><tr><td>37</td><td>SPI_BIOS_CS1#</td><td></td><td>17</td><td>RESET_IN#</td><td></td></tr><tr><td>36</td><td>SPI_BIOS_MISO</td><td></td><td>16</td><td>DATA</td><td></td></tr><tr><td>35</td><td>SPI_BIOS_MOSI</td><td></td><td>15</td><td>CLK</td><td></td></tr><tr><td>34</td><td>SPI_BIOS_CLK</td><td></td><td>14</td><td>OCD0A</td><td>Include a jumper to connect OCD0A via 1K0 pull-up to 3.3V_BMC</td></tr><tr><td>33</td><td rowspan="10">LPC Bus</td><td>3V3_LPC</td><td></td><td>13</td><td>OCD0B</td><td>Include a jumper to connect OCD0A via 1K0 pull-up to 3.3V_BMC</td></tr><tr><td>32</td><td>GND</td><td></td><td>12</td><td rowspan="7">Test points</td><td>PWRBTN#</td><td></td></tr><tr><td>31</td><td>CB_RESET#</td><td>Platform Reset</td><td>11</td><td>SYS_RESET#</td><td></td></tr><tr><td>30</td><td>RST#</td><td></td><td>10</td><td>CB_RESET#</td><td></td></tr><tr><td>29</td><td>CLK33_LPC</td><td></td><td>9</td><td>CB_PWROK</td><td></td></tr><tr><td>28</td><td>LPC_FRAME#</td><td></td><td>8</td><td>SUS_S3#</td><td></td></tr><tr><td>27</td><td>LPC_AD3</td><td></td><td>7</td><td>SUS_S4#</td><td></td></tr><tr><td>26</td><td>LPC_AD2</td><td></td><td>6</td><td>SUS_S5#</td><td></td></tr><tr><td>25</td><td>LPC_AD1</td><td></td><td>5</td><td rowspan="4">BMC Debug signals</td><td>POSTWDT_DIS#</td><td>Connect to Jumper for Debug</td></tr><tr><td>24</td><td>LPC_AD0</td><td></td><td>4</td><td>SEL_BIOS</td><td>Connect to Jumper for Debug</td></tr><tr><td>23</td><td rowspan="3">BMC Program interface</td><td>3.3V_BMC</td><td></td><td>3</td><td>BIOS_MODE</td><td>Connect to Jumper for Debug</td></tr><tr><td>22</td><td>3.3V_BMC</td><td></td><td>2</td><td>BMC_STATUS</td><td></td></tr><tr><td>21</td><td>GND</td><td></td><td>1</td><td>Reserved</td><td></td><td></td></tr></table>

Note: The pin description on the Debug Module is the inverse of that on the motherboard.

# 4.3. Jumper and Switch Settings

![CMOS\nJPS3P1\nMPCIE_S\nEL\nJPS4P1\nJPS6M2\nJPS6M1\nJPS5M2\nJPS5M1\nSW1\nSWS1M\nSER1 PWR SEL\n(JPS1P)\nBIOS WP\nATX/AT Mode\nJumper\n(JPATX)](.amitx-cf-g-50m-00093-1000-20/9e28d749892d5b4e53f28e2986483d49298087e91953e69efd8d780c3d48ba95.jpg)

Figure 5: Jumper and Switch Locations

# 4.3.1. ATX/AT Mode Jumper Selection (JPATX)

<table><tr><td>JP1</td><td>ATX/AT Mode</td></tr><tr><td>1-2</td><td>ATX (default)</td></tr><tr><td>2-3</td><td>AT</td></tr></table>

# 4.3.2. Clear CMOS (CMOS)

<table><tr><td>JP6</td><td>Clear CMOS</td></tr><tr><td>1-2</td><td>Normal (default)</td></tr><tr><td>2-3</td><td>Clear CMOS</td></tr></table>

# 4.3.3. COM Port (SER1) Mode Selection Switch (SWS1M)

<table><tr><td colspan="4">SWS1M (SER1 Mode Select)</td></tr><tr><td></td><td>RS-232 (default)</td><td>RS-422</td><td>RS-485</td></tr><tr><td>1</td><td>ON</td><td>ON</td><td>OFF</td></tr><tr><td>2</td><td>OFF</td><td>ON</td><td>ON</td></tr></table>

# 4.3.4. COM Port (SER1) Power Selection Jumper (JPS1P)

<table><tr><td>JPS1P</td><td>SER1 Power</td></tr><tr><td>1-2</td><td>5V</td></tr><tr><td>2-3</td><td>NC (default)</td></tr><tr><td>3-4</td><td>12V</td></tr></table>

# 4.3.5. SER5-6 Mode Select (JPS5M1/ JPS5M2 ; JPS6M1/ JPS6M2)

<table><tr><td colspan="2">SER5-6 Mode Select</td></tr><tr><td>RS-232 (default)</td><td>ccTalk</td></tr><tr><td>1-3</td><td>3-5</td></tr><tr><td>2-4</td><td>4-6</td></tr></table>

# 4.3.6. BIOS Switch Setting (SW1)

<table><tr><td colspan="3">Fail Safe SPI0 + SPI1 (default)</td></tr><tr><td></td><td>ON</td><td>OFF</td></tr><tr><td>1</td><td>Boot from on board BIOS (Default)</td><td>Boot from socket BIOS</td></tr><tr><td>2</td><td>Normal BIOS Mode</td><td>Failsafe BIOS Mode (Default)</td></tr></table>

Default: 1 ON and 2 OFF (Boot from onboard BIOS and enable failsafe.)

# 4.3.7. BIOS Write Protect Selection (BIOS\_WP)

<table><tr><td colspan="2">BIOS_WP BIOS Write Protect Selection</td></tr><tr><td>1-2</td><td>BMCControl(Default)</td></tr><tr><td>2-3</td><td>Enable</td></tr></table>

Note: There will be the following limitations with write protect enabled:

A. S3 and S4 will not be supported under OS.
B. IAMT cannot be supported
C. ME version information in the BIOS menu will show “zero”
D. Do not install OS when BIOS Write Protect is enabled.
E. Intel GbE LAN cannot update MAC address
F. User cannot refresh the BIOS.

# 4.3.8. SATA1 DOM Power Selection (JPS3P1)

<table><tr><td colspan="2">JPS3P1 SATA1 DOM Power Selection</td></tr><tr><td>1-2</td><td>3.3V</td></tr><tr><td>2-3</td><td>5V</td></tr><tr><td>N/C</td><td>Default</td></tr></table>

# 4.3.9. SATA2 DOM Power Selection (JPS4P1)

<table><tr><td colspan="2">JPS4P1 SATA2 DOM Power Selection</td></tr><tr><td>1-2</td><td>3.3V</td></tr><tr><td>2-3</td><td>5V</td></tr><tr><td>N/C</td><td>Default</td></tr></table>

# 4.4. Onboard Connector Information

Table 2: AmITX-CF-G Onboard Connector Information

<table><tr><td>Connector</td><td>CN#</td><td colspan="2">Onboard ConnectorManufacturer Part No.</td><td colspan="2">Mating ConnectorManufacturer Part No.</td><td>ADLINK Cable</td></tr><tr><td>COM Port</td><td>SER1-6</td><td>JVE</td><td>21-65310-2050</td><td>YOUNG YAK</td><td>YY-1970H-2*5P(PH2.0)</td><td>30-20876-0000(optional)</td></tr><tr><td>ATX power</td><td>ATX_PW</td><td>Molex</td><td>20-65703-2070</td><td>E.C.I</td><td>E.C.I 5016H-2*7P (PH4.2)</td><td>30-20872-0000(standard)</td></tr><tr><td>USB (H310)</td><td>USB2</td><td>CST</td><td>21-65350-0090</td><td>YOUNG YAK</td><td>YY-1970H-2*5P(PH2.0)</td><td>30-20874-1000(optional)</td></tr><tr><td>USB (Q370)</td><td>USB2</td><td>LOTES</td><td>21-653A0-2100</td><td>ALLPASS Elec</td><td>A37-0903-113</td><td>30-20963-0000(optional)</td></tr><tr><td>SATA Power</td><td>ST_PWR1-2</td><td>JVE</td><td>20-65210-1050</td><td>YOUNG YAK</td><td>YY-1970H-2*5P(PH2.0)</td><td>30-20875-0000(standard)</td></tr><tr><td>SATA</td><td>SATA1-3</td><td>WIN WIN</td><td>21-H14A0-0070</td><td>N/A</td><td>N/A</td><td>30-10057-0600(standard)</td></tr><tr><td>DB-40</td><td>DB1</td><td>Molex</td><td>61-02603-0400</td><td>N/A</td><td>N/A</td><td>30-30016-0000(optional)</td></tr><tr><td>Feature</td><td>FEATURE1</td><td>JVE</td><td>21-65320-2140</td><td>JWT</td><td>JWT A2005H00-2C*14 (PH2.0)</td><td>N/A</td></tr><tr><td>Audio</td><td>AUD_HEAD1</td><td>JVE</td><td>21-F2000-0250</td><td>JWT</td><td>JWT A2005H00-2CX13P(PH2.0)</td><td>N/A</td></tr><tr><td>Front Panel</td><td>FRNTPNL1</td><td>JVE</td><td>21-65310-2120</td><td>YY</td><td>YY-1970H-2*12P (PH2.0)</td><td>N/A</td></tr></table>

# 5. Driver Installation

Drivers can be downloaded through the following link:

https://www.adlinktech.com/en/Industrial\_Motherboards\_SBCs\_Mini-ITX\_Embedded\_Boards

This page intentionally left blank.

# 6. Smart Embedded Management Agent (SEMA)

The onboard microcontroller (BMC) implements power sequencing and Smart Embedded Management Agent (SEMA) functionality.

The microcontroller communicates via the System Management Bus with the CPU/chipset. The following functions are implemented.

• Total operating hours counter. Counts the number of hours the module has been run in minutes.
• On-time minutes counter. Counts the seconds since last system start.
• Temperature monitoring of CPU and board temperature. Minimum and maximum temperature values of CPU and board are stored in flash.
• Power cycles counter
• Boot counter. Counts the number of boot attempts.
• Watchdog Timer (Type-II). Set / Reset / Disable Watchdog Timer. Features auto-reload at power-up.
• System Restart Cause. Power loss / BIOS Fail / Watchdog / Internal Reset / External Reset
• Fail-safe BIOS support. In case of a boot failure, hardware signals tell external logic to boot from fail-safe BIOS.
• Flash area. 1kB Flash area for customer data
• 128 Bytes Protected Flash area. Keys, IDs, etc. can be stored in a write- and clear-protectable region.
• Board Identify. Vendor / Board / Serial number / Production Date
• Main-current & voltage. Monitors drawn current and main voltages

For a detailed description of SEMA features and functionality, please refer to the SEMA Technical Manual and SEMA Software Manual, downloadable on the ADLINK web site: www.adlinktech.com.

# 6.1. Board Specific SEMA Functions

# 6.1.1. Voltages

The BMC implements a voltage monitor and samples several onboard voltages. The voltages can be read by calling the SEMA function “Get Voltages”. The function returns a 16-bit value divided into high-byte (MSB) and lowbyte (LSB).

Table 3: SEMA Onboard Voltage Monitor

<table><tr><td>ADC Channel</td><td>Voltage Name</td></tr><tr><td>0</td><td>N/A</td></tr><tr><td>1</td><td>VIN</td></tr><tr><td>2</td><td>5VSB</td></tr><tr><td>3</td><td>RTC</td></tr></table>

# 6.1.2. Main Current

The BMC implements a current monitor. The current can be read by calling the SEMA function “Get Main Current”. The function returns four 16-bit values divided in high-byte (MSB) and low-byte (LSB). These 4 values represent the last 4 currents drawn by the board. The values are sampled every 250ms. The order of the 4 values is NOT in chronological order. Access by the BMC may increase the drawn current of the whole system. In this case, there are still 3 samples not influenced by the read access.

$$
\text { Main   Current } = (\text { MSB\_n } &lt;   &lt;   8 + \text { LSB\_n }) \times 8. 0 6 \mathrm{mA}
$$

# 6.1.3. BMC Status

This register shows the status of BMC controlled signals on the AmITX-CF-G.

Table 4: SEMA BMC Status

&lt;table&gt;<tr><td>Status Bit</td><td>Signal</td></tr><tr><td>0</td><td>WDT_OUT</td></tr><tr><td>3</td><td>BIOS_MODE</td></tr><tr><td>4</td><td>POSTWDT_DISn</td></tr><tr><td>5</td><td>SEL_BIOS</td></tr><tr><td>6</td><td>BMC_SPI0_WPn</td></tr></table>

# 6.1.4. Exception Codes

In case of an error, the BMC drives a blinking code on the blue Status LED (LED1). The same error code is also reported by the BMC Flags register. The Exception Code is not stored in the Flash Storage and is cleared when the power is removed. Therefore, a “Clear Exception Code” command is not needed or supported.

Table 5: SEMA Exception Codes

<table><tr><td>Exception Code</td><td>Error Message</td></tr><tr><td>0</td><td>NOERROR</td></tr><tr><td>2</td><td>NO_SUSCLK</td></tr><tr><td>3</td><td>NO_SLP_S5</td></tr><tr><td>4</td><td>NO_RSMRST</td></tr><tr><td>5</td><td>NO_SLP_S3</td></tr><tr><td>6</td><td>BIOS_FAIL</td></tr><tr><td>7</td><td>PLTRST_FAIL</td></tr><tr><td>8</td><td>NO_SYS_PWRGD</td></tr><tr><td>9</td><td>NO_VCORE_PWRGD</td></tr><tr><td>10</td><td>CRITICAL_TEMP</td></tr><tr><td>11</td><td>NO_VIN</td></tr><tr><td>12</td><td>NO_V5SBY</td></tr><tr><td>13</td><td>NO_VRTC</td></tr></table>

# 6.1.5. BMC Flags

The BMC Flags register returns the last detected Exception Code since power-up and shows the BIOS in use and the power mode.

Table 6: SEMA BMC Flags

<table><tr><td>Bit</td><td>Description</td></tr><tr><td>[0 ~ 4]</td><td>Exception Code</td></tr><tr><td>[6]</td><td>0 = AT mode1 = ATX mode</td></tr><tr><td>[7]</td><td>0 = Standard BIOS1 = Fail-safe BIOS.</td></tr></table>

This page intentionally left blank.

# 7. System Resources

# 7.1. System Memory Map

Table 7: System Memory Map

<table><tr><td>Address Range (decimal)</td><td>Address Range (hex)</td><td>Size</td><td>Description</td></tr><tr><td>(4GB-2MB)</td><td>FFE00000 – FFFFFFFF</td><td>2 MB</td><td>High BIOS Area</td></tr><tr><td>(4GB-18MB) – (4GB-17MB-1)</td><td>FEE00000 – FEEFFFFFF</td><td>1 MB</td><td>MSI Interrupts</td></tr><tr><td>(4GB-20MB) – (4GB-19MB-1)</td><td>FEC00000 – FECFFFFFF</td><td>1 MB</td><td>APIC Configuration Space</td></tr><tr><td>15MB – 16MB</td><td>F00000 – FFFFFFF</td><td>1 MB</td><td>ISA Hole</td></tr><tr><td>1MB -15MB</td><td>100000 - EFFFFF</td><td>14MB</td><td>Main Memory</td></tr><tr><td>0K –1MB</td><td>00000 – FFFFFFF</td><td>1MB</td><td>DOS Compatibility Memory</td></tr></table>

# 7.2. I/O Map

Table 8: I/O Map

<table><tr><td>Hex Range</td><td>Device</td></tr><tr><td>020h – 02Dh &amp; 030h – 03Dh</td><td>Interrupt controller 1, 8259 equivalent</td></tr><tr><td>02Eh – 02Fh</td><td>Motherboard resource</td></tr><tr><td>040h – 043h &amp; 050h – 053h</td><td>System Timer</td></tr><tr><td>04Eh – 04Fh</td><td>Super IO</td></tr><tr><td>060h, 062h, 064h, 066h, 068h – 06Fh</td><td>8042 equivalent (keyboard)</td></tr><tr><td>061h, 063h, 065h, 067h</td><td>NMI control and status</td></tr><tr><td>070h – 077h</td><td>Real Time Clock Controller (bit 7 – NMI mask)</td></tr><tr><td>092h</td><td>Reset(Bit 0)/Fast Gate A20 (Bit 1)</td></tr><tr><td>0A0h – 0B1h &amp; 0B4h – 0BDh</td><td>Interrupt Controller 2, 8259 equivalent</td></tr><tr><td>0B2h and 0B3h</td><td>APM control and status port respectively</td></tr><tr><td>0E0h – 0EFh</td><td>Available</td></tr><tr><td>0F0h</td><td>Co-processor error register</td></tr><tr><td>2E0h – 2E7h</td><td>Serial Port 6</td></tr><tr><td>2E8h – 2EFh</td><td>Serial Port 4</td></tr><tr><td>2F8h – 2FFh</td><td>Serial Port 2</td></tr><tr><td>3E0h – 3E7h</td><td>Serial Port 5</td></tr><tr><td>3E8h – 3EFh</td><td>Serial Port 3</td></tr><tr><td>3F8h – 3FFh</td><td>Serial Port 1</td></tr><tr><td>378h – 37Fh</td><td>Available</td></tr><tr><td>380h – 3AFh</td><td>Available</td></tr><tr><td>4D0h</td><td>Master PIC Edge/Level Trigger register</td></tr><tr><td>4D1h</td><td>Slave PIC Edge/Level Trigger register</td></tr><tr><td>0A00h – 0A2Fh</td><td>Reserved for SIO functions base address (ex: PME/GPIO etc.)</td></tr><tr><td>0CF8h – 0CFBh</td><td>PCI configuration address register (32bit I/O only)</td></tr><tr><td>0CF9h</td><td>Reset Controller register (8 bit I/O)</td></tr><tr><td>0CFCh – 0CFFh</td><td>PCI configuration data register</td></tr><tr><td>1C00h</td><td>GPIO Base Address for SB</td></tr><tr><td>1800h</td><td>PM (ACPI) Base Address for SB</td></tr><tr><td>1860h</td><td>Alias for ICH TCO base address</td></tr><tr><td>0D000h – 0EFFH</td><td>PCIe Root Port</td></tr><tr><td>0F000h – 0F03Fh</td><td>VGA</td></tr><tr><td>0F040h – 0F05Fh</td><td>SMBus controller</td></tr><tr><td>0F060h – 0F07Fh</td><td>SATA controller</td></tr></table>

# 7.3. Interrupt Request (IRQ) Lines

# 7.3.1. IRQ Lines PIC Mode

Note (1): These IRQs can be used for PCI devices when onboard device is disabled.
Table 9: IRQ Lines PIC Mode

<table><tr><td>IRQ#</td><td>Typical Interrupt Resource</td><td>Connected to Pin</td><td>Available</td></tr><tr><td>0</td><td>Counter 0</td><td>N/A</td><td>No</td></tr><tr><td>1</td><td>Keyboard controller</td><td>N/A</td><td>No</td></tr><tr><td>2</td><td>Cascade interrupt from slave PIC</td><td>N/A</td><td>No</td></tr><tr><td>3</td><td>Serial Port 2 (COM2)</td><td>IRQ3 via SERIRQ / PIRQ</td><td>Note (1)</td></tr><tr><td>4</td><td>Serial Port 1 (COM1)</td><td>IRQ4 via SERIRQ / PIRQ</td><td>Note (1)</td></tr><tr><td>5</td><td>Generic</td><td>N/A</td><td>No</td></tr><tr><td>6</td><td>Serial Port 3~6 (COM3~6)</td><td>IRQ6 via SERIRQ / PIRQ</td><td>Note (1)</td></tr><tr><td>7</td><td>Generic</td><td>N/A</td><td>No</td></tr><tr><td>8</td><td>Real-time clock</td><td>N/A</td><td>No</td></tr><tr><td>9</td><td>Generic</td><td>N/A</td><td>No</td></tr><tr><td>10</td><td>Generic</td><td>N/A</td><td>No</td></tr><tr><td>11</td><td>Generic</td><td>N/A</td><td>No</td></tr><tr><td>12</td><td>PS/2 Mouse</td><td>IRQ12 via SERIRQ/PIRQ</td><td>No</td></tr><tr><td>13</td><td>Math Processor</td><td>N/A</td><td>No</td></tr><tr><td>14</td><td>Generic</td><td>N/A</td><td>No</td></tr><tr><td>15</td><td>Intel SD Host Controller</td><td>N/A</td><td>Note</td></tr></table>

# 7.3.2. IRQ Lines APIC Mode

Table 10: IRQ Lines APIC Mode

<table><tr><td>IRQ#</td><td>Typical Interrupt Resource</td><td>Connected to Pin</td><td>Available</td></tr><tr><td>0</td><td>Counter 0</td><td>N/A</td><td>No</td></tr><tr><td>1</td><td>Keyboard Controller</td><td>N/A</td><td>No</td></tr><tr><td>2</td><td>Cascade Interrupt from slave PIC</td><td>N/A</td><td>No</td></tr><tr><td>3</td><td>Serial Port 2 (COM2)</td><td>IRQ3 via SERIRQ/PIRQ</td><td>No</td></tr><tr><td>4</td><td>Serial Port 1 (COM1)</td><td>IRQ4 via SERIRQ/PIRQ</td><td>No</td></tr><tr><td>5</td><td>Serial Port 3 (COM3)</td><td>IRQ5 via SERIRQ/PIRQ</td><td>No</td></tr><tr><td>6</td><td>Serial Port 5 (COM5)</td><td>IRQ6 via SERIRQ/PIRQ</td><td>No</td></tr><tr><td>7</td><td>Serial Port 4 (COM4)</td><td>IRQ7 via SERIRQ/PIRQ</td><td>No</td></tr><tr><td>8</td><td>Real-Time Clock</td><td>N/A</td><td>No</td></tr><tr><td>9</td><td>Generic</td><td>N/A</td><td>No</td></tr><tr><td>10</td><td>Serial Port 6 (COM6)</td><td>IRQ10 via SERIRQ/PIRQ</td><td>No</td></tr><tr><td>11</td><td>N/A</td><td>IRQ11 via SERIRQ/PIRQ</td><td>No</td></tr><tr><td>12</td><td>PS/2 Mouse</td><td>IRQ12 via SERIRQ/PIRQ</td><td>No</td></tr><tr><td>13</td><td>Math Processor</td><td>N/A</td><td>No</td></tr><tr><td>14</td><td>Generic</td><td>N/A</td><td>No</td></tr><tr><td>15</td><td>Intel SD Host Controller</td><td>N/A</td><td>No</td></tr><tr><td>16-511</td><td>Microsoft ACPI-Compliant System</td><td>N/A</td><td>Yes</td></tr></table>

Note (1): These IRQs can be used for PCI devices when onboard device is disabled.

# 7.4. PCI Configuration Space Map

Table 11: PCI Configuration Space Map

<table><tr><td>Bus Number</td><td>Device Number</td><td>Function Number</td><td>Routing</td><td>Description</td></tr><tr><td>00h</td><td>00h</td><td>00h</td><td>N/A</td><td>Intel Host Bridge</td></tr><tr><td>00h</td><td>01h</td><td>00h</td><td>N/A</td><td>Intel PEG port</td></tr><tr><td>00h</td><td>02h</td><td>00h</td><td>Internal</td><td>Intel I.G.D.</td></tr><tr><td>00h</td><td>08h</td><td>00h</td><td>Internal</td><td>System device</td></tr><tr><td>00h</td><td>14h</td><td>00h</td><td>Internal</td><td>xHCI Controller</td></tr><tr><td>00h</td><td>14h</td><td>02h</td><td>Internal</td><td>Data Acquisition</td></tr><tr><td>00h</td><td>16h</td><td>00h</td><td>Internal</td><td>Intel Management Engine Interface #1</td></tr><tr><td>00h</td><td>17h</td><td>00h</td><td>Internal</td><td>Intel AHCI controller</td></tr><tr><td>00h</td><td>1Ch</td><td>00h</td><td>Internal</td><td>Intel PCI Express Root port 1</td></tr><tr><td>00h</td><td>1Ch</td><td>06h</td><td>Internal</td><td>Intel PCI Express Root port 7</td></tr><tr><td>00h</td><td>1Ch</td><td>07h</td><td>Internal</td><td>Intel PCI Express Root port 8</td></tr><tr><td>00h</td><td>1Fh</td><td>00h</td><td>Internal</td><td>Intel ISA Bridge</td></tr><tr><td>00h</td><td>1Fh</td><td>03h</td><td>Internal</td><td>Intel Multimedia</td></tr><tr><td>00h</td><td>1Fh</td><td>04h</td><td>Internal</td><td>Intel SMBUS</td></tr><tr><td>00h</td><td>1Fh</td><td>05h</td><td>Internal</td><td>SPI (flash) Controller</td></tr><tr><td>01h(Note 1)</td><td>00h</td><td>00h</td><td>Internal</td><td>Intel PEG Slot</td></tr><tr><td>02h(Note 1)</td><td>00h</td><td>00h</td><td>Internal</td><td>Realtek Ethernet controller</td></tr><tr><td>03h(Note 1)</td><td>00h</td><td>00h</td><td>Internal</td><td>Realtek Ethernet controller</td></tr></table>

Note (1): The bus number will be changed if the PEG/PCIE port has device.

# 7.5. PCI Interrupt Routing Map

Table 12: PCI Interrupt Routing Map

<table><tr><td>INT Line</td><td>P.E.G Root Port</td><td>Intel PEG port</td><td>Intel I.G.D.</td><td>System device</td><td>xHCI Controller</td><td>Data Acquisition</td></tr><tr><td>Int0</td><td>INTA:16</td><td>INTA:16</td><td>INTA:16</td><td>INTA:16</td><td>INTA:16</td><td>INTA:16</td></tr><tr><td>Int1</td><td>INTB:17</td><td>INTB:17</td><td>INTB:17</td><td>INTB:17</td><td>INTB:17</td><td>INTB:17</td></tr><tr><td>Int2</td><td>INTC:18</td><td>INTC:18</td><td>INTC:18</td><td>INTC:18</td><td>INTC:18</td><td>INTC:18</td></tr><tr><td>Int3</td><td>INTD:19</td><td>INTD:19</td><td>INTD:19</td><td>INTD:19</td><td>INTD:19</td><td>INTD:19</td></tr></table>

<table><tr><td>INT Line</td><td>Intel ME Controller</td><td>Intel AHCI controller</td><td>PCIE port 1</td><td>PCIE port 7</td><td>PCIE port 8</td><td>ISA Bridge</td></tr><tr><td>Int0</td><td>INTA:16</td><td>INTB:17</td><td>INTA:16</td><td>INTC:18</td><td>INTD:19</td><td>INTA:16</td></tr><tr><td>Int1</td><td>INTB:17</td><td>INTC:18</td><td>INTB:17</td><td>INTD:19</td><td>INTA:16</td><td>INTB:17</td></tr><tr><td>Int2</td><td>INTC:18</td><td>INTD:19</td><td>INTC:18</td><td>INTA:16</td><td>INTB:17</td><td>INTC:18</td></tr><tr><td>Int3</td><td>INTD:19</td><td>INTA:16</td><td>INTD:19</td><td>INTB:17</td><td>INTC:18</td><td>INTD:19</td></tr></table>

<table><tr><td>INT Line</td><td>Memory controller</td><td>Multimedia</td><td>SMBus Controller</td><td>Intel Ethernet controller</td><td>PEG Slot</td></tr><tr><td>Int0</td><td>INTA:16</td><td>INTA:16</td><td>INTA:16</td><td>INTA:16</td><td>INTA:16</td></tr><tr><td>Int1</td><td>INTB:17</td><td>INTB:17</td><td>INTB:17</td><td>INTB:17</td><td>INTB:17</td></tr><tr><td>Int2</td><td>INTC:18</td><td>INTC:18</td><td>INTC:18</td><td>INTC:18</td><td>INTC:18</td></tr><tr><td>Int3</td><td>INTD:19</td><td>INTD:19</td><td>INTD:19</td><td>INTD:19</td><td>INTD:19</td></tr></table>

<table><tr><td>INT Line</td><td>Realtek Ethernet Controller</td><td>Realtek Ethernet Controller</td></tr><tr><td>Int0</td><td>INTB:17</td><td>INTC:18</td></tr><tr><td>Int1</td><td>INTC:18</td><td>INTD:19</td></tr><tr><td>Int2</td><td>INTD:19</td><td>INTA:16</td></tr><tr><td>Int3</td><td>INTA:16</td><td>INTB:17</td></tr></table>

# 7.6. SMBus Slave Address

Table 13: SMBus Slave Address

<table><tr><td>Device</td><td>Address</td></tr><tr><td>DIMM A</td><td>A0h</td></tr><tr><td>DIMM B</td><td>A4h</td></tr><tr><td>BMC</td><td>50h</td></tr></table>

This page intentionally left blank.

# 8. BIOS Setup

The AmITX-CF-G is provided with a pre-installed AMI EFI BIOS firmware configurable via a setup utility that is invoked during the BIOS boot phase. The BIOS configuration is stored in the NVRAM part of the SPI Flash chip. All settings will remain valid after the system is powered down. The following sections describe the BIOS setup menu and the setting options for each menu item.

# 8.1. BIOS Setup Menu

The BIOS setup utility is invoked by pressing the &lt;ESC&gt; or &lt;DEL&gt; key. Users can change the BIOS settings when the setup utility runs. A reset of the system is required in order for the new settings to take effect.

# 8.1.1. Hot Keys

In the BIOS setup utility, there are several hot keys designed for specific purposes. The hot keys are listed below:

&lt;F1&gt;: General help in setup menu
&lt;F8&gt;: Load previous BIOS values
&lt;F9&gt;: Load BIOS default in setup utility
&lt;F10&gt;: Save & Exit setup utility

# 8.1.2. Menu Selection Bar

The Menu Selection Bar is located at the top of the screen. It displays the top-level menus available to the user:

 Main Menu
 Advanced Menu
 Chipset Menu
 Security Menu
 Boot Menu
 Save & Exit Menu

# 8.1.3. Menu Conventions

The appearance of the setup menu is a sample to describe the item list. It is shown on the VT100 terminal via serial console. The followings are the menu conventions.

Using color
The mandatory BIOS setup fields are in black. The BIOS setup fields currently not used are in grey. The display-only strings are in black.
Using brackets
Editable menu options are marked with squares ‘[‘ and ‘]’ to distinguish them from display-only fields that cannot be modified.

# 8.2. Menu Structure

This section presents the six primary menus of the BIOS Setup Utility. Use the following table as a quick reference for the contents of the BIOS Setup Utility. The subsections in this section describe the submenus and setting options for each menu item. The default setting options are presented in bold, and the function of each setting is described in the right-hand column of the respective table.

<table><tr><td>Main</td><td>Advanced</td><td>Chipset</td><td>Security</td><td>Boot</td><td>Save &amp; Exit</td></tr><tr><td>BIOS InformationSystem InformationBoard InformationSystem DateSystem TimeAccess Level</td><td>CPU ConfigurationPower ManagementSystem ManagementThermal ManagementWatchdog TimerSuper IO ConfigurationSerial Console RedirectionHardware MonitorTPM 2.0 ConfigurationS5 RTC Wake SettingsNVMe ConfigurationLAN ConfigurationUSB ConfigurationMiscellaneousNetwork Stack ConfigurationRealtek PCIe GBE Family Controller (MAC address1)Realtek PCIe GBE Family Controller (MAC address2)</td><td>System Agent (SA)ConfigurationPCH-IO Configuration</td><td>Password DescriptionAdministrator PasswordUser PasswordSecure Boot menu</td><td>Boot Config-urationSetup Prompt TimeoutBootup NumLock StateQuiet BootFast BootBoot OptionBoot Option #1Boot Option #2Boot Option #3Boot Option #4Boot Option #5Boot Option #6Boot Option #7Boot Option #8</td><td>Save Changes and ExitDiscard Changes and ExitSave Changes and ResetDiscard Charges and ResetSave OptionsSave ChangesDiscard ChangesRestore DefaultsSave as User DefaultsRestore User DefaultsBoot OverrideLaunch EFI shell from filesystem device</td></tr></table>

Note: ► indicates a submenu. Gray text indicates info only.

# 8.3. Main Menu

The Main Menu provides read-only information about your system and also allows you to set the System Date and Time. Refer to the tables below for details of the submenus and settings.

# 8.3.1. Main

<table><tr><td>Feature</td><td>Options</td><td>Description</td></tr><tr><td>BIOS Information</td><td colspan="2">Info only</td></tr><tr><td>System Information</td><td colspan="2">Info only</td></tr><tr><td>Board Information ▶</td><td>Submenu</td><td>Display board information</td></tr><tr><td>Board Information</td><td colspan="2">Info only</td></tr><tr><td>System Date</td><td>Weekday, MM/DD/YYYY</td><td>Requires the alpha-numeric entry of the day of the week, day of the month, calendar month, and all 4 digits of the year, indicating the century and year (Fri XX/XX/20XX)</td></tr><tr><td>System Time</td><td>HH/MM/SS</td><td>Presented as a 24-hour clock setting in hours, minutes, and seconds</td></tr><tr><td>Access Level</td><td>Info Only</td><td>BIOS setup utility access level</td></tr></table>

# 8.4. Advanced

This menu contains the settings for most of the user interfaces in the system.

# 8.4.1. Advanced > CPU Configuration

<table><tr><td>Feature</td><td>Options</td><td>Description</td></tr><tr><td>CPU Configuration ▶</td><td>Submenu</td><td>CPU Configuration</td></tr><tr><td>CPU Configuration</td><td colspan="2">Info only</td></tr><tr><td>Active Processor Core</td><td>All123</td><td>Number of cores to enable in each processor package.</td></tr><tr><td>Intel (VMX) Virtualization Technology</td><td>DisabledEnabled</td><td>When enabled, a VMM can utilize the additional hardware capabilities provided by Vanderpool Technology.</td></tr><tr><td>Intel Trusted Execution Technology</td><td>DisabledEnabled</td><td>Enables utilization of additional hardware capabilities provided by Intel (R) Trusted Execution Technology.</td></tr><tr><td>Intel(R) SpeedStep(tm)</td><td>DisabledEnabled</td><td>Allows more than two frequency ranges to be supported.</td></tr><tr><td>Intel(R) Speed Shift Technology</td><td>DisabledEnabled</td><td>Enable/Disable Intel(R) Speed Shift Technology support. Enabling will expose the CPPC v2 interface to allow for hardware controlled P-states.</td></tr><tr><td>Turbo Mode</td><td>DisabledEnabled</td><td>Enable/Disable processor Turbo Mode (requires Intel Speed Step or Intel Speed Shift to be available and enabled).</td></tr><tr><td>C states</td><td>DisabledEnabled</td><td>Enable/Disable CPU Power Management. Allows CPU to go to C states when it's not 100% utilized.</td></tr><tr><td rowspan="11">Package C State Limit</td><td>C0/C1</td><td rowspan="11">Maximum Package C State Limit Setting. CpuDefault: Leaves to Factory default value.Auto:Initializes to deepest available Package C State Limit.</td></tr><tr><td>C2</td></tr><tr><td>C3</td></tr><tr><td>C6</td></tr><tr><td>C7</td></tr><tr><td>C7S</td></tr><tr><td>C8</td></tr><tr><td>C9</td></tr><tr><td>C10</td></tr><tr><td>CPU Default</td></tr><tr><td>Auto</td></tr></table>

# 8.4.2. Advanced > Power Management

<table><tr><td>Feature</td><td>Options</td><td>Description</td></tr><tr><td>Power Management ▶</td><td>Submenu</td><td>Power Management</td></tr><tr><td>Enable ACPI Auto Configuration</td><td>Disabled Enabled</td><td>Enables or Disables BIOS ACPI Auto Configuration.</td></tr><tr><td>Enable Hibernation</td><td>Disabled Enabled</td><td>Enables or Disables System ability to Hibernate (OS/S4 Sleep State). This option may not be effective with some operating systems.</td></tr><tr><td>ACPI Sleep State</td><td>Suspend Disabled S3 (Suspend to RAM)</td><td>Select the highest ACPI sleep state the system will enter when the SUSPEND button is pressed.</td></tr><tr><td>Restore On AC Power Loss</td><td>Power On Power Off Last State</td><td>Select AC power state when power is re-applied after a power failure.</td></tr><tr><td>Emulate AT Mode</td><td>Emulate AT ATX</td><td>Select Emulate AT or ATX function. If this option is set to [Emulation AT], BIOS will report no suspend functions (S3 &amp; S4) to ACPI OS. In Windows XP, it will make OS show a shutdown message during system shutdown. ATX: OS will turn off system power when shut down.</td></tr><tr><td>ECO Mode</td><td>Disabled Enabled</td><td>Reduces the power consumption of the system, but after a shut down, you have to wait at least 5 seconds before you can restart the system.</td></tr></table>

# 8.4.3. Advanced > System Management

<table><tr><td>Feature</td><td>Options</td><td>Description</td></tr><tr><td>System Management ▶</td><td>Submenu</td><td>Display System Management</td></tr><tr><td>System Management</td><td colspan="2">Info only</td></tr><tr><td>SEMA Features ▶</td><td>Submenu</td><td>Display SEMA Features</td></tr><tr><td>SEMA Features:</td><td colspan="2">Info only</td></tr><tr><td>Flags ▶</td><td>Submenu</td><td>Display Flags</td></tr><tr><td>BMC Flags</td><td colspan="2">Info only</td></tr></table>

8.4.4. Advanced > Thermal Management

<table><tr><td>Feature</td><td>Options</td><td>Description</td></tr><tr><td>Thermal Management ▶</td><td>Submenu</td><td>Thermal Management</td></tr><tr><td>CPU Temperature</td><td colspan="2">Info only</td></tr><tr><td>Board Temperatures</td><td colspan="2">Info only</td></tr><tr><td>CPU Fan Speed</td><td>Info only</td><td>Display CPU fan speed</td></tr><tr><td>System Fan1 Speed</td><td>Info only</td><td>Display system fan 1 speed</td></tr><tr><td>System Fan2 Speed</td><td>Info only</td><td>Display system fan 2 speed</td></tr><tr><td>Smart Fan ▶</td><td>Submenu</td><td>Smart Fan</td></tr><tr><td>CPU Smart Fan Temperature Source</td><td>CPU Sensor Board Sensor</td><td>CPU Smart FanTemperature Source</td></tr><tr><td>CPU Fan Mode</td><td>AUTO (Smart Fan) Fan Off Fan On</td><td>CPU Fan Mode</td></tr><tr><td>System Smart Fan1Temperature Source</td><td>CPU Sensor Board Sensor</td><td>System Smart Fan1Temperature Source</td></tr><tr><td>System Fan1 Mode</td><td>AUTO (Smart Fan) Fan Off Fan On</td><td>System Fan1 Mode</td></tr><tr><td>System Smart Fan2Temperature Source</td><td>CPU Sensor Board Sensor</td><td>System Smart Fan2Temperature Source</td></tr><tr><td>System Fan2 Mode</td><td>AUTO (Smart Fan) Fan Off Fan On</td><td>System Fan2 Mode</td></tr><tr><td>Critical Trip Point</td><td>Disabled 80 C 90 C 95 C</td><td>This value is the temperature threshold of the Critical Trip Point.</td></tr><tr><td>Passive Cooling Trip Point</td><td>Disabled 70 C 80 C 90 C</td><td>This value is the temperature threshold of the Passive Cooling Trip Point.</td></tr></table>

8.4.5. Advanced > Watchdog Timer

<table><tr><td>Feature</td><td>Options</td><td>Description</td></tr><tr><td>Watchdog Timer ▶</td><td>Submenu</td><td>Watchdog Timer</td></tr><tr><td>Power-Up WatchdogATTENTION: Pressing F12 during start up disables the Power Up Watchdog.</td><td>DisabledEnabled</td><td>The Power Up Watchdog resets the system after a certain amount of time after power-up.</td></tr><tr><td>RunTime Watchdog</td><td>DisabledEnabled</td><td>The RunTime Watchdog resets the system after a certain amount of time after power-up.</td></tr></table>

8.4.6. Advanced > Super IO Configuration

<table><tr><td>Feature</td><td>Options</td><td>Description</td></tr><tr><td>Super IO Configuration ▶</td><td>Submenu</td><td>Super IO Configuration</td></tr><tr><td>COM1 Device SettingsCOM1 Control</td><td>Info only</td><td>IO Address &amp; IRQ InfoCOM mode</td></tr><tr><td>COM2 Device Settings</td><td>Info only</td><td>IO Address &amp; IRQ Info</td></tr><tr><td>COM3 Device Settings</td><td>Info only</td><td>IO Address &amp; IRQ Info</td></tr><tr><td>COM4 Device Settings</td><td>Info only</td><td>IO Address &amp; IRQ Info</td></tr><tr><td>COM5 Device Settings</td><td>Info only</td><td>IO Address &amp; IRQ Info</td></tr><tr><td>COM6 Device Settings</td><td>Info only</td><td>IO Address &amp; IRQ Info</td></tr></table>

Note: COM1-6 in BIOS correspond to the serial ports SER1-6 on the AmITX-CF-G board.

8.4.7. Advanced > Serial Console Redirection

<table><tr><td>Feature</td><td>Options</td><td>Description</td></tr><tr><td>Serial Console Redirection ▶</td><td>Submenu</td><td>Serial Console Redirection</td></tr><tr><td>COM1</td><td colspan="2">Info only</td></tr><tr><td>Console Redirection</td><td>Disabled Enabled</td><td>Console Redirection Enable or Disable.</td></tr><tr><td>Console Redirection Settings ▶</td><td>Submenu (see Section 8.4.7.1)</td><td>The settings specify how the host computer and the remote computer (which the user is using) will exchange data. Both computers should have the same or compatible settings.</td></tr><tr><td>COM2</td><td colspan="2">Info only</td></tr><tr><td>Console Redirection</td><td>Disabled Enabled</td><td>Console Redirection Enable or Disable.</td></tr><tr><td>Console Redirection Settings ▶</td><td>Submenu (see Section 8.4.7.1)</td><td>The settings specify how the host computer and the remote computer (which the user is using) will exchange data. Both computers should have the same or compatible settings.</td></tr><tr><td>COM3</td><td colspan="2">Info only</td></tr><tr><td>Console Redirection</td><td>Disabled Enabled</td><td>Console Redirection Enable or Disable.</td></tr><tr><td>Console Redirection Settings ▶</td><td>Submenu (see Section 8.4.7.1)</td><td>The settings specify how the host computer and the remote computer (which the user is using) will exchange data. Both computers should have the same or compatible settings.</td></tr><tr><td>COM4</td><td colspan="2">Info only</td></tr><tr><td>Console Redirection</td><td>Disabled Enabled</td><td>Console Redirection Enable or Disable.</td></tr><tr><td>Console Redirection Settings ▶</td><td>Submenu (see Section 8.4.7.1)</td><td>The settings specify how the host computer and the remote computer (which the user is using) will exchange data. Both computers should have the same or compatible settings.</td></tr><tr><td>COM5</td><td colspan="2">Info only</td></tr><tr><td>Console Redirection</td><td>Disabled Enabled</td><td>Console Redirection Enable or Disable.</td></tr><tr><td>Console Redirection Settings ▶</td><td>Submenu (see Section 8.4.7.1)</td><td>The settings specify how the host computer and the remote computer (which the user is using) will exchange data. Both computers should have the same or compatible settings.</td></tr><tr><td>COM6</td><td colspan="2">Info only</td></tr><tr><td>Console Redirection</td><td>Disabled Enabled</td><td>Console Redirection Enable or Disable.</td></tr><tr><td>Console Redirection Settings ▶</td><td>Submenu (see Section 8.4.7.1)</td><td>The settings specify how the host computer and the remote computer (which the user is using) will exchange data. Both computers should have the same or compatible settings.</td></tr></table>

# 8.4.7.1. Advanced > Serial Console Redirection > Console Redirection Settings COM[1-6]

<table><tr><td>Feature</td><td>Options</td><td>Description</td></tr><tr><td>COM[1-6]Console Redirection Settings</td><td colspan="2">Info only</td></tr><tr><td>Terminal Type</td><td>VT100VT100+VT-UTF8ANSI</td><td>Emulation: ANSI: Extended ASCII char set. VT100: ASCII char set. VT100+: Extends VT100 to support color, function keys, etc. VT-UTF8: Uses UTF8 encoding to map Unicode chars onto 1 or more bytes.</td></tr><tr><td>Bits per second</td><td>9600192003840057600115200</td><td>Selects serial port transmission speed. The speed must be matched on the other side. Long or noisy lines may require lower speeds.</td></tr><tr><td>Data Bits</td><td>78</td><td>Data Bits</td></tr><tr><td>Parity</td><td>NoneEvenOddMarkSpace</td><td>A parity bit can be sent with the data bits to detect some transmission errors. Even: parity bit is 0 if the num of 1's in the data bits is even. Odd: parity bit is 0 if num of 1's in the data bits is odd. Mark: parity bit is always 1. Space: Parity bit is always 0. Mark and Space Parity do not allow for error detection</td></tr><tr><td>Stop Bits</td><td>12</td><td>Stop bits indicate the end of a serial data packet. (A start bit indicates the beginning). The standard setting is 1 stop bit. Communication with slow devices may require more than 1 stop bit.</td></tr><tr><td>Flow Control</td><td>NoneHardware RTS/CTS</td><td>Flow control can prevent data loss from buffer overflow. When sending data, if the receiving buffers are full, a 'stop' signal can be sent to stop the data flow. Once the buffers are empty, a 'start' signal can be sent to re-start the flow. Hardware flow control uses two wires to send start/stop signals.</td></tr><tr><td>VT-UTF8 Combo Key Support</td><td>DisabledEnabled</td><td>Enable VT-UTF8 Combination Key Support for ANSI/VT100 terminals</td></tr><tr><td>Recorder Mode</td><td>DisabledEnabled</td><td>With this mode enabled only text will be sent. This is to capture Terminal data.</td></tr><tr><td>Resolution 100x31</td><td>DisabledEnabled</td><td>Enables or disables extended terminal resolution</td></tr><tr><td>Putty KeyPad</td><td>VT100LINUXXTERMR6SCOESCNVT400</td><td>Select FunctionKey and KeyPad on Putty.</td></tr></table>

# 8.4.8. Advanced > Hardware Monitor

<table><tr><td>Feature</td><td>Options</td><td>Description</td></tr><tr><td>Hardware Monitor ▶</td><td>Submenu</td><td>Hardware Monitor</td></tr><tr><td>Power Consumption</td><td colspan="2">Info only</td></tr></table>

# 8.4.9. Advanced > TPM 2.0 Configuration

<table><tr><td>Feature</td><td>Options</td><td>Description</td></tr><tr><td>TPM 2.0 Configuration ▶</td><td>Submenu</td><td>TPM 2.0 Configuration</td></tr><tr><td>TPM 2.0 Configuration</td><td colspan="2">Info only</td></tr><tr><td>TPM20 Device Found</td><td colspan="2">Info only</td></tr><tr><td>Firmware Version:</td><td colspan="2">Info only</td></tr><tr><td>Vendor:</td><td colspan="2">Info only</td></tr><tr><td>Security Device Support</td><td>DisabledEnabled</td><td>Enable or Disable BIOS support for security device.O.S. will not show Security Device. TCG EFI protocol and INT1A interface will not be available.</td></tr><tr><td>Active PCR banks</td><td colspan="2">Info only</td></tr><tr><td>Available PCR banks</td><td colspan="2">Info only</td></tr><tr><td>SHA-1 PCR Bank</td><td>DisabledEnabled</td><td>Enable or Disable SHA-1 PCR Bank</td></tr><tr><td>SHA256 PCR Bank</td><td>DisabledEnabled</td><td>Enable or Disable SHA256 PCR Bank</td></tr><tr><td>Pending operation</td><td>NoneTPM Clear</td><td>Schedule an Operation for the Security Device.NOTE: Your Computer will reboot during restart in order to change State of Security Device.</td></tr><tr><td>Platform Hierarchy</td><td>EnabledDisabled</td><td>Enable or Disable Platform Hierarchy</td></tr><tr><td>Storage Hierarchy</td><td>EnabledDisabled</td><td>Enable or Disable Storage Hierarchy</td></tr><tr><td>Endorsement Hierarchy</td><td>EnabledDisabled</td><td>Enable or Disable Endorsement Hierarchy</td></tr><tr><td>TPM2.0 UEFI Spec Version</td><td>TCG_1_2TCG_2</td><td>Select the TCG2 Spec Version Support,TCG_1_2: the Compatible mode for Win8/Win10,TCG_2: Support for new TCG2 protocol and event format for Win10 or later</td></tr><tr><td>Physical Presence Spec Version</td><td>1.21.3</td><td>Select to Tell O.S. to support PPI Spec Version 1.2 or 1.3. Note some HCK tests might not support 1.3</td></tr><tr><td>PH Randomization</td><td>DisabledEnabled</td><td>Enables or Disables Platform Hierarchy randomization. DO NOT ENABLE THIS QUESTION IN PRODUCTION PLATFORMS. THIS IS FOR DEVELOPMENT TESTING. OVERRIDE ChangePlatformAuth ELINK for production platforms supporting TXT.</td></tr></table>

# 8.4.10. Advanced > S5 RTC Wake Settings

<table><tr><td>Feature</td><td>Options</td><td>Description</td></tr><tr><td>S5 RTC Wake Settings ▶</td><td>Submenu</td><td>S5 RTC Wake Settings</td></tr><tr><td>RTC Wake system from S5</td><td>DisabledFixed TimeDynamic Time</td><td>Enable or disable System wake on alarm event.FixedTime: system will wake on the hr::min::sec specified.DynamicTime: system will wake on the current time + Increase minute(s)</td></tr></table>

# 8.4.11. Advanced > NVMe Configuration

<table><tr><td>Feature</td><td>Options</td><td>Description</td></tr><tr><td>NVMe Configuration ▶</td><td>Submenu</td><td>NVMe Configuration</td></tr><tr><td>NVMe Configuration</td><td colspan="2">Info only</td></tr></table>

# 8.4.12. Advanced > LAN Configuration

<table><tr><td>Feature</td><td>Options</td><td>Description</td></tr><tr><td>LAN Configuration ▶</td><td>Submenu</td><td>LAN Configuration</td></tr><tr><td>LAN Configuration</td><td colspan="2">Info only</td></tr><tr><td>LAN1 Enable</td><td>DisabledEnabled</td><td>Enable or Disable LAN1</td></tr><tr><td>LAN2 Enable</td><td>DisabledEnabled</td><td>Enable or Disable LAN2</td></tr><tr><td>LAN Wake</td><td>DisabledEnabled</td><td>Enable or Disable LAN Wake function</td></tr></table>

8.4.13. Advanced > USB Configuration

<table><tr><td>Feature</td><td>Options</td><td>Description</td></tr><tr><td>USB Configuration ▶</td><td>Submenu</td><td>USB Configuration</td></tr><tr><td>USB Configuration</td><td colspan="2">Info only</td></tr><tr><td>USB Module version</td><td colspan="2">Info only</td></tr><tr><td>USB Controllers:</td><td colspan="2">Info only</td></tr><tr><td>USB Devices:</td><td colspan="2">Info only</td></tr><tr><td>XHCI Hand-off</td><td>DisabledEnabled</td><td>This is a workaround for OSes without XHCI hand-off support. The XHCI ownership change should be claimed by XHCI driver.</td></tr><tr><td>USB Mass Storage Driver Support</td><td>EnabledDisabled</td><td>Enable/Disable USB Mass Storage Driver Support.</td></tr><tr><td>USB hardware delays and time-outs:</td><td colspan="2">Info only</td></tr><tr><td>USB transfer time-out</td><td>1 sec5 sec10 sec20 sec</td><td>The time-out value for Control, Bulk, and Interrupt transfers.</td></tr><tr><td>Device reset time-out</td><td>10 sec20 sec30 sec40 sec</td><td>USB mass storage device Start Unit command time-out.</td></tr><tr><td>Device power-up delay</td><td>AutoManual</td><td>Maximum time the device will take before it properly reports itself to the Host Controller. &#x27;Auto&#x27; uses default value: for a Root port it is 100 ms, for a Hub port the delay is taken from Hub descriptor.</td></tr></table>

8.4.14. Advanced > Miscellaneous

<table><tr><td>Feature</td><td>Options</td><td>Description</td></tr><tr><td>Miscellaneous ▶</td><td>Submenu</td><td>Miscellaneous</td></tr><tr><td>Miscellaneous</td><td colspan="2">Info only</td></tr><tr><td>SPI ROM WP ▶</td><td>Submenu</td><td>SPI ROM Write Protection</td></tr><tr><td>SPI ROM Write Protect</td><td>Disabled Enabled</td><td>Enable/Disable SPI ROM Write Protect</td></tr><tr><td>Chassis Intrusion Support</td><td>Disabled Enabled</td><td>Enable or Disable Chassis Intrusion Support</td></tr></table>

8.4.15. Advanced > Network Stack Configuration

<table><tr><td>Feature</td><td>Options</td><td>Description</td></tr><tr><td>Network Stack Configuration ▶</td><td>Submenu</td><td>Network Stack Configuration</td></tr><tr><td>Network Stack</td><td>DisabledEnabled</td><td>Enable/Disable UEFI Network Stack</td></tr></table>

8.4.16. Advanced > Realtek PCIe GBE Family Controller (MAC address1)

<table><tr><td>Feature</td><td>Options</td><td>Description</td></tr><tr><td>Realtek PCIe GBE Family Controller (MAC address1) ▶</td><td>Submenu</td><td>Realtek PCIe GBE Family Controller (MAC address1)</td></tr><tr><td>Driver Information</td><td>Info only</td><td></td></tr><tr><td>Device Information</td><td>Info only</td><td></td></tr><tr><td>Patent Information</td><td>Info only</td><td></td></tr></table>

8.4.17. Advanced > Realtek PCIe GBE Family Controller (MAC address2)

<table><tr><td>Feature</td><td>Options</td><td>Description</td></tr><tr><td>Realtek PCIe GBE Family Controller (MAC address2) ▶</td><td>Submenu</td><td>Realtek PCIe GBE Family Controller (MAC address2)</td></tr><tr><td>Driver Information</td><td>Info only</td><td></td></tr><tr><td>Device Information</td><td>Info only</td><td></td></tr><tr><td>Patent Information</td><td>Info only</td><td></td></tr></table>

# 8.5. Chipset

8.5.1. Chipset > System Agent (SA) Configuration

<table><tr><td>Feature</td><td>Options</td><td>Description</td></tr><tr><td>System Agent (SA) Configuration ▶</td><td>Submenu</td><td>System Agent (SA) Configuration</td></tr><tr><td>System Agent (SA) Configuration</td><td colspan="2">Info only</td></tr><tr><td>SA PCIe Code Version</td><td colspan="2">Info only</td></tr><tr><td>VT-d</td><td colspan="2">Info only</td></tr><tr><td>Memory Configuration ▶</td><td>Submenu</td><td>Memory Configuration parameters</td></tr><tr><td>Memory Configuration</td><td colspan="2">Info only</td></tr><tr><td>Max TOLUD</td><td>Dynamic1 GB1.25 GB1.5 GB1.75 GB2 GB2.25 GB2.5 GB2.75 GB3 GB3.25 GB3.5 GB</td><td>Maximum Value of TOLUD. Dynamic assignment would adjust TOLUD automatically based on largest MMIO length of installed graphics controller.</td></tr><tr><td>MRC Fast Boot</td><td>DisabledEnabled</td><td>Enable/Disable fast path through the MRC</td></tr><tr><td>Memory Remap</td><td>DisabledEnabled</td><td>Enable/Disable Memory Remap above 4GB</td></tr><tr><td>Memory Thermal Management</td><td>DisabledEnabled</td><td>Enable/Disable Memory Thermal Management</td></tr><tr><td>SPD Write Protect</td><td>DisabledEnabled</td><td>Enable/Disable setting SPD Write Protect. For security recommendations, SPD write disable bit must be set.</td></tr><tr><td>Graphics Configuration ▶</td><td>Submenu</td><td>Graphics Configuration</td></tr><tr><td>Graphics Configuration</td><td>Info only</td><td></td></tr><tr><td>Primary Display</td><td>AutoIGFXPEG</td><td>Select which of IGFX/PEG/PCI Graphics device should be Primary Display or select SG for Switchable Gfx.</td></tr><tr><td>Internal Graphics</td><td>AutoDisabledEnabled</td><td>Keep IGFX enabled based on the setup options.</td></tr><tr><td>GTT Size</td><td>2MB4MB8MB</td><td>Select the GTT Size</td></tr><tr><td>DVMT Total Gfx Mem</td><td>128M256MMAX</td><td>Select DVMT5.0 Total Graphic Memory size used by the Internal Graphics Device.</td></tr><tr><td>PEG Port Configuration ▶</td><td>Submenu</td><td>PEG Port Options</td></tr><tr><td>PEG Port Configuration</td><td colspan="2">Info only</td></tr><tr><td>VT-d</td><td>DisabledEnabled</td><td>Enable or Disable VT-d capability</td></tr><tr><td>Above 4GB MMIO BIOS assignment</td><td>DisabledEnabled</td><td>Enable or disable above 4GB MemoryMappedIO BIOS assignment This is enabled automatically when Aperture Size is set to 2048MB.</td></tr></table>

8.5.2. Chipset > PCH-IO Configuration

<table><tr><td>Feature</td><td>Options</td><td>Description</td></tr><tr><td>PCH-IO Configuration ▶</td><td>Submenu</td><td></td></tr><tr><td>PCH-IO Configuration</td><td colspan="2">Info only</td></tr><tr><td>PCI Express Configuration ▶</td><td>Submenu</td><td>PCI Express Configuration settings</td></tr><tr><td>PCI Express Configuration</td><td>Info only</td><td></td></tr><tr><td>PCI Express Clock Gating</td><td>DisabledEnabled</td><td>PCI Express Clock Gating Enable/Disable for each root port.</td></tr><tr><td>Pcie PII SSC</td><td>Auto0.0%0.1%0.2%0.3%0.4%0.5%0.6%0.7%0.8%0.9%1.0%1.1%1.2%1.3%1.4%1.5%1.6%1.7%1.8%1.9%2.0%</td><td>Pcie PII SSC percentage. AUTO - Keep hw default, no BIOS override. Range is 0.0%-2.0%.</td></tr><tr><td>SATA Configuration ▶</td><td>Submenu</td><td>SATA Device Options Settings</td></tr><tr><td>SATA Configuration</td><td>Info only</td><td></td></tr><tr><td>SATA Controller(s)</td><td>DisabledEnabled</td><td>Enable/Disable SATA Device</td></tr><tr><td>SATA Mode Selection</td><td>AHCIIntel RST Premium With Intel Optane SystemAcceleration</td><td>Determines how SATA controller(s) operate</td></tr><tr><td>SATA Controller Speed</td><td>DefaultGen1Gen2Gen3</td><td>Indicates the maximum speed the SATA controller can support.</td></tr><tr><td>Serial ATA Port 0</td><td colspan="2">Info only</td></tr><tr><td>Port 0</td><td>DisabledEnabled</td><td>Enable or Disable SATA Port</td></tr><tr><td>Hot Plug</td><td>DisabledEnabled</td><td>Designates this port as Hot Pluggable.</td></tr><tr><td>Serial ATA Port 1</td><td colspan="2">Info only</td></tr><tr><td>Port 1</td><td>DisabledEnabled</td><td>Enable or Disable SATA Port</td></tr><tr><td>Hot Plug</td><td>DisabledEnabled</td><td>Designates this port as Hot Pluggable.</td></tr><tr><td>Serial ATA Port 2</td><td colspan="2">Info only</td></tr><tr><td>Port 2</td><td>DisabledEnabled</td><td>Enable or Disable SATA Port</td></tr><tr><td>Hot Plug</td><td>DisabledEnabled</td><td>Designates this port as Hot Pluggable.</td></tr><tr><td>Serial ATA Port 3</td><td colspan="2">Info only</td></tr><tr><td>Port 3</td><td>DisabledEnabled</td><td>Enable or Disable SATA Port</td></tr><tr><td>Serial ATA Port 4</td><td colspan="2">Info only</td></tr><tr><td>Port 4</td><td>DisabledEnabled</td><td>Enable or Disable SATA Port</td></tr><tr><td>USB Configuration ▶</td><td>Submenu</td><td>USB Configuration settings</td></tr><tr><td>USB Configuration</td><td colspan="2">Info only</td></tr><tr><td>USB Port Disable Override</td><td>Disable LinkSelect Per-Pin</td><td>Selectively Enable/Disable the corresponding USB port from reporting a Device Connection to the controller.</td></tr><tr><td>Security Configuration ▶</td><td>Submenu</td><td>Security Configuration settings</td></tr><tr><td>Security Configuration</td><td colspan="2">Info only</td></tr><tr><td>RTC Lock</td><td>DisabledEnabled</td><td>Enable will lock bytes 38h-3Fh in the lower/upper 128-byte bank of RTC RAM.</td></tr><tr><td>BIOS Lock</td><td>DisabledEnabled</td><td>Enable/Disable the PCH BIOS Lock Enable feature. Required to be enabled to ensure SMM protection of flash.</td></tr><tr><td>HD Audio Configuration ▶</td><td>Submenu</td><td>HD Audio Subsystem Configuration Settings</td></tr><tr><td>HD Audio SubsystemConfiguration Setting</td><td colspan="2">Info only</td></tr><tr><td>HD Audio</td><td>DisabledEnabled</td><td>Control Detection of the HD-Audio deviceDisabled = HDA will be unconditionally disabledEnabled = HDA will be unconditionally enabled.</td></tr><tr><td>Audio Output Selection</td><td>AD7.1 for Audio JackAD5.1 for Audio Jack</td><td>AD7.1 or AD5.1 for Audio Jack</td></tr></table>

8.6. Security

<table><tr><td>Feature</td><td>Options</td><td>Description</td></tr><tr><td>Password Description</td><td colspan="2">Info only</td></tr><tr><td>Administrator Password</td><td>Enter password</td><td></td></tr><tr><td>User Password</td><td>Enter password</td><td></td></tr><tr><td>Secure Boot menu ▶</td><td>Submenu</td><td>Secure Boot configuration</td></tr><tr><td>Secure Boot</td><td colspan="2">Info only</td></tr><tr><td>System Mode</td><td colspan="2">Info only</td></tr><tr><td>Secure Boot</td><td colspan="2">Info only</td></tr><tr><td>Secure Boot Control</td><td>DisabledEnabled</td><td>Secure Boot feature is Active if Secure Boot is Enabled, Platform Key(PK) is enrolled and the System is in User mode. The mode change requires platform reset.</td></tr></table>

8.7. Boot

<table><tr><td>Feature</td><td>Options</td><td>Description</td></tr><tr><td>Boot Configuration ▶</td><td colspan="2">Info only</td></tr><tr><td>Setup Prompt Timeout</td><td>Input Range 1~15</td><td>Number of seconds to wait for setup activation key. The maximum value is 15.</td></tr><tr><td>Bootup NumLock State</td><td>OnOff</td><td>Select the keyboard NumLock state.</td></tr><tr><td>Quiet Boot</td><td>DisabledEnabled</td><td>Enable or disables Quiet Boot option.</td></tr><tr><td>Fast Boot</td><td>DisabledEnabled</td><td>Enables or disables boot with initialization of a minimal set of devices required to launch active boot option. Has no effect for BBS boot options.</td></tr><tr><td>Boot Option ▶</td><td colspan="2">Info only</td></tr><tr><td>Boot Option #1</td><td>Hard DiskCD/DVDUSB Hard DiskUSB CD/DVDUSB KeyUSB FloppyUSB LanNetworkDisabled</td><td>Sets the system boot order</td></tr><tr><td>Boot Option #2</td><td>Hard DiskCD/DVDUSB Hard DiskUSB CD/DVDUSB KeyUSB FloppyUSB LanNetworkDisabled</td><td>Sets the system boot order</td></tr><tr><td>Boot Option #3</td><td>Hard DiskCD/DVDUSB Hard DiskUSB CD/DVDUSB KeyUSB FloppyUSB LanNetworkDisabled</td><td>Sets the system boot order</td></tr><tr><td>Boot Option #4</td><td>Hard DiskCD/DVDUSB Hard DiskUSB CD/DVDUSB KeyUSB FloppyUSB LanNetworkDisabled</td><td>Sets the system boot order</td></tr><tr><td>Boot Option #5</td><td>Hard DiskCD/DVDUSB Hard DiskUSB CD/DVDUSB KeyUSB FloppyUSB LanNetworkDisabled</td><td>Sets the system boot order</td></tr><tr><td>Boot Option #6</td><td>Hard DiskCD/DVDUSB Hard DiskUSB CD/DVDUSB KeUSB FloppyUSB LanNetworkDisabled</td><td>Sets the system boot order</td></tr><tr><td>Boot Option #7</td><td>Hard DiskCD/DVDUSB Hard DiskUSB CD/DVDUSB KeyUSB FloppyUSB LanNetworkDisabled</td><td>Sets the system boot order</td></tr><tr><td>Boot Option #8</td><td>Hard DiskCD/DVDUSB Hard DiskUSB CD/DVDUSB KeyUSB FloppyUSB LanNetworkDisabled</td><td>Sets the system boot order</td></tr></table>

# 8.8. Save & Exit

<table><tr><td>Feature</td><td>Options</td><td>Description</td></tr><tr><td>Save Changes and Exit</td><td>Yes No</td><td>Exit system setup after saving the changes.</td></tr><tr><td>Discard Changes and Exit</td><td>Yes No</td><td>Exit system setup without saving any changes.</td></tr><tr><td>Save Changes and Reset</td><td>Yes No</td><td>Reset the system after saving the changes.</td></tr><tr><td>Discard Changes and Reset</td><td>Yes No</td><td>Reset system setup without saving any changes.</td></tr><tr><td>Save Options ▶</td><td colspan="2">Info only</td></tr><tr><td>Save Changes</td><td>Yes No</td><td>Save Changes done so far to any of the setup options.</td></tr><tr><td>Discard Changes</td><td>Yes No</td><td>Discard Changes done so far to any of the setup options.</td></tr><tr><td>Restore Defaults</td><td>Yes No</td><td>Restore/Load Default values for all the setup options.</td></tr><tr><td>Save as User Defaults</td><td>Yes No</td><td>Save the changes done so far as User Defaults.</td></tr><tr><td>Restore User Defaults</td><td>Yes No</td><td>Restore the User Defaults to all the setup options.</td></tr><tr><td>Boot Override ▶</td><td colspan="2">Info only</td></tr><tr><td>Launch EFI Shell from filesystem device</td><td>Enter</td><td>Attempts to Launch EFI Shell application (Shell.efi) from one of the available filesystem devices</td></tr></table>

# Safety Instructions

Read and follow all instructions marked on the product and in the documentation before you operate your system. Retain all safety and operating instructions for future use.

• Please read these safety instructions carefully.
• Please keep this User‘s Manual for later reference.
• Read the specifications section of this manual for detailed information on the operating environment of this equipment.
• When installing/mounting or uninstalling/removing equipment, turn off the power and unplug any power cords/cables.
• To avoid electrical shock and/or damage to equipment:

 Keep equipment away from water or liquid sources.
 Keep equipment away from high heat or high humidity.
 Keep equipment properly ventilated (do not block or cover ventilation openings).
 Make sure to use recommended voltage and power source settings.
 Always install and operate equipment near an easily accessible electrical socket-outlet.
 Secure the power cord (do not place any object on/over the power cord).
 Only install/attach and operate equipment on stable surfaces and/or recommended mountings.
 If the equipment will not be used for long periods of time, turn off and unplug the equipment from its power source.

• Never attempt to fix the equipment. Equipment should only be serviced by qualified personnel.

# Getting Service

Ask an Expert: http://askanexpert.adlinktech.com

# ADLINK Technology, Inc.

Address: No. 66, Huaya 1st Rd., Guishan District Taoyuan City 333411, Taiwan

Tel: +886-3-216-5088

Fax: +886-3-328-5706

Email: service@adlinktech.com

# Ampro ADLINK Technology, Inc.

Address: 6450 Via Del Oro San Jose, CA 95119-1208, USA

Tel: +1-408-360-0200

Toll Free: +1-800-966-5200 (USA only)

Fax: +1-408-600-1189

Email: info@adlinktech.com

# ADLINK Technology (China) Co., Ltd.

Address: 300 Fang Chun Rd., Zhangjiang Hi-Tech Park, Pudong New Area Shanghai, 201203 China

Tel: +86-21-5132-8988

Fax: +86-21-5132-3588

Email: market@adlinktech.com

# ADLINK Technology GmbH

Address: Hans-Thoma-Straße 11, D-68163, Mannheim, Germany

Tel: +49-621-43214-0

Fax: +49-621 43214-30

Email: emea@adlinktech.com

Please visit the Contact page at www.adlinktech.com for information on how to contact the ADLINK regional office nearest you.
[🔗 Link to the original document](.amitx-cf-g-50m-00093-1000-20/amitx-cf-g-50m-00093-1000-20.pdf)