# EOS-1300 Series

# EOS-1300/EOS-1310/EOS-1320/EOS-1330

# 4CH GigE Vision System

# User's Manual

![COM1\nCOM2\nI/O 2\nSP\nSP\nSP\nAudio\nI/O 1\nADLINK\nPROFESSIONAL OCEMBER\nCH1\nCH2\nCH3\nCH4\nPWR\nStatus HDD\nV-\n+\nV+\n24V DC IN](.eos-1300-50-1z222-2000-200-en/67a32fada4e024b4982fe6ecad0543a4ef06652eb14e0dfe109d6aef5eedf136.jpg)

Manual Rev.: 2.00

Revision Date: Nov. 4, 2016

Part No: 50-1Z222-2000

# Revision History

<table><tr><td>Revision</td><td>Release Date</td><td>Description of Change(s)</td></tr><tr><td>2.00</td><td>Nov. 4, 2016</td><td>Initial Release</td></tr><tr><td></td><td></td><td></td></tr></table>

# Preface

# Copyright 2016 ADLINK Technology, Inc.

This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer.

# Disclaimer

The information in this document is subject to change without prior notice in order to improve reliability, design, and function and does not represent a commitment on the part of the manufacturer.

In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.

# Environmental Responsibility

ADLINK is committed to fulfill its social responsibility to global environmental preservation through compliance with the European Union's Restriction of Hazardous Substances (RoHS) directive and Waste Electrical and Electronic Equipment (WEEE) directive. Environmental protection is a top priority for ADLINK. We have enforced measures to ensure that our products, manufacturing processes, components, and raw materials have as little impact on the environment as possible. When products are at their end of life, our customers are encouraged to dispose of them in accordance with the product disposal and/or recovery programs prescribed by their nation or company.

# Trademarks

Product names mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks of their respective companies.

# Conventions

Take note of the following conventions used throughout this manual to make sure that users perform certain tasks and instructions properly.

![The image depicts a white document icon with a folded upper-left corner and faint horizontal gray lines. A large, bold red checkmark is superimposed diagonally across the center of the paper.](.eos-1300-50-1z222-2000-200-en/e81941dea6085a20d14ed9fd4feed0b015dd51b9f4799dddb8c89df7c699ee9f.jpg)
NOTE:

Additional information, aids, and tips that help users perform tasks.

![The image displays a yellow triangular warning sign with a thick black border. Centered inside the triangle is a large black exclamation mark.](.eos-1300-50-1z222-2000-200-en/0b904ccbde41921f450fab8f92460223453e73d7e18250c943d2026569dac968.jpg)
CAUTION:

Information to prevent minor physical injury, component damage, data loss, and/or program corruption when trying to complete a task.

![The image shows a standard warning symbol: a red triangle with a white border containing a white exclamation point in the center against a white background.](.eos-1300-50-1z222-2000-200-en/0d1c10fd86a8c32fcaedc25f7f6add0dd2cfe8039ff5aed87e1f95430fe5ea6a.jpg)
WARNING:

Information to prevent serious physical injury, component damage, data loss, and/or program corruption when trying to complete a specific task.

# Table of Contents

# Revision History...... ii

# Preface...... iii

# List of Tables...... vii

# List of Figures ix

# 1 Introduction ...... 1

1.1 Features.... 2
1.2 Specifications.... 3
1.3 Mechanical Drawings.... 5
1.4 Front Panel I/O Connectors 6

1.4.1 LED Indicators 7
1.4.2 Power Button 7
1.4.3 Reset Button 8
1.4.4 DC Power Connector....8
1.4.5 GigE Camera Port 9
1.4.6 Digital I/O and Encoder Connectors (I/O1 and I/O2) 10
1.4.7 Serial ports (COM1 and COM2) 13
1.4.8 LAN Ports 15
1.4.9 DisplayPort Connectors.... 17
1.4.10 USB Ports 17

1.5 DI/O and Encoder Sample Circuits.... 19

1.5.1 Isolated Digital Input Circuits 19
1.5.2 Isolated Digital Output Circuits 19
1.5.3 Isolated Encoder Input Circuits....20

# 2 Getting Started 23

2.1 Unpacking Checklist 23
2.2 Adaptors & Additional Accessories.... 23

2.3 Installing Memory 23
2.4 Installing a Hard Disk or SS Drive.... 25
2.5 Installing the Internal USB Dongle 28
2.6 Installing Wall-mount Brackets.... 29
2.7 Installing DIN Rail Bracket 30
2.8 Cooling Considerations.... 31
2.9 Driver Installation 32

# A Appendix: BIOS Setup....33

A.1 Main 34

A.1.1 System Management....36

A.2 Advanced 45

A.2.1 CPU 46
A.2.2 SATA 49
A.2.3 Memory....50
A.2.4 Graphics 51
A.2.5 USB 52
A.2.6 Super IO 54
A.2.7 Serial Port Console....57
A.2.8 Network....58
A.2.9 Security....59

A.3 Security 62

A.4 Boot 63

A.4.1 CSM Configuration 65

A.5 Save & Exit 67

# Important Safety Instructions.... 69

# Getting Service 73

# List of Tables

Table 1-1: LED Indicator Legend....7

Table 1-2: DC Power Supply Connector Signals....8

Table 1-3: GigE Camera Port Pin Assignments .... 10

Table 1-4: LED Indicator Legend....10

Table 1-5: I/O1, DB-26P Connector Pin Assignments.... 11

Table 1-6: I/O2 DB-37P Connector Pin Assignments.... 12

Table 1-7: COM1 and COM2 Connectors Pin Assignments..... 14

Table 1-8: SWS1M1 Switch Setting.... 15

Table 1-9: LAN Port Pin Definitions....16

Table 1-10: LAN Port LED Legend 16

Table 1-11: DisplayPort Pin Assignment 17

Table 1-12: USB 2.0 Pin Assignments 18

Table 1-13: USB 3.0 Pin Assignments 19

This page intentionally left blank.

# List of Figures

Figure 1-1: Top View....5

Figure 1-2: Front View....5

Figure 1-3: Rear View 6

Figure 1-4: (Right) Side View....6

Figure 1-5: Front Panel I/O 6

Figure 1-6: Power Supply Connector Pin Assignments ....8

Figure 1-7: GigE Camera Port 9

Figure 1-8: I/O1, DB-26P Digital I/O Connector....10

Figure 1-9: I/O2, DB-37P Digital I/O and Encoder Connector...... 11

Figure 1-10: COM1 and COM2 Connectors.... 13

Figure 1-11: SWS1M1 Switch.... 14

Figure 1-12: SWS1M1 Switch Location .... 15

Figure 1-13: LAN Port 16

Figure 1-14: DisplayPort Connector....17

Figure 1-15: USB 2.0 18

Figure 1-16: USB 3.0 18

Figure 1-17: Digital Input Sample Application Circuit.... 19

Figure 1-18: Digital Output Sample Application Circuit for Sink Type....20

Figure 1-19: Digital Output Sample Application Circuit for Source Type 20

Figure 1-20: Encoder Input Sample Application Circuit for Line Driver 21

Figure 1-21: Encoder Input Sample Application Circuit for Open Collector....21

This page intentionally left blank.

# 1 Introduction

![Back panel of a black ADLINK network device showing ports, connectors, and I/O ports (no readable text or symbols beyond labels)](.eos-1300-50-1z222-2000-200-en/b117c90e0bf7a30eb58c17692b5712c3127898b9a44bfebe2c1f44a71a878cae.jpg)

The Adlink EOS-1300 4CH GigE vision system provides isolated, real-time DI/O, encoder, and support for PoE (Power over Ethernet) in a compact 232W x 180.8D x 82.8H mm construction. Leveraging 6th Generation Intel® Core™ i7 Processors, the EOS-1300 is suitable for multi-camera high resolution machine vision applications that require high computing power, and offers not only an internal USB port but also onboard SHA-256 security EEPROM to help manage copy protection and license authentication. Special DI/O features like De-bounce filter, FPGA based trigger I/O, and Encoder interlocking can be configured by software API maximum flexibility and significantly reduced TCO.

With its highly integrated DI/O function, GigE vision, and PoE technology, the EOS-1300 is the ideal choice for machine production or factory automation operations requiring compact size, 2 to 4 GigE-enabled cameras, and DI/O & Encoder control.

# 1.1 Features

▶ 6th Gen Intel® Core™ i7/i5/i3 processors
▶ FPGA-based DI/O, trigger I/O and encoder functions, fixed and low latency
▶ 232W x 180.8D x 82.8H mm (9.1 x 7.1 x 3.4 in) with front-mounted I/O
▶ Internal USB port and onboard SHA-256 License Security EEPROM for third party software protection
▶ Up to 4CH GigE vision camera with PoE (power over Ethernet) support

# 1.2 Specifications

<table><tr><td></td><td>EOS-1300</td><td>EOS-1310</td><td>EOS-1320</td><td>EOS-1330</td></tr><tr><td colspan="5">System Core</td></tr><tr><td>Processor</td><td>Intel®CoreTMi7-6700</td><td>Intel®CoreTMi5-6500</td><td>Intel®CoreTMi3-6100</td><td>Intel®G3900</td></tr><tr><td>Memory</td><td colspan="4">DDR4 2133 4GB (up to 32 GB)</td></tr><tr><td colspan="5">OS</td></tr><tr><td>Supported OS</td><td colspan="4">W7P/W8.1/W10 64bit</td></tr><tr><td colspan="5">Graphics</td></tr><tr><td>Display Port</td><td colspan="4">2</td></tr><tr><td colspan="5">Camera Interface</td></tr><tr><td>GigE Vision</td><td colspan="4">4-CH Gigabit, support for PoE (power over Ethernet), IEEE 802.3af compliantPoE output: 8W/port</td></tr><tr><td colspan="5">I/O interface</td></tr><tr><td>Ethernet</td><td colspan="4">2 x Intel GbE ports</td></tr><tr><td>DI/O</td><td colspan="4">Isolated 12 DI, 16 DO</td></tr><tr><td>Encoder</td><td colspan="4">Isolated 2CH A/B/Z encoder</td></tr><tr><td>USB</td><td colspan="4">4 x USB3.0 + 4 x USB2.0 + 1 x USB2.0 internal</td></tr><tr><td>Series port</td><td colspan="4">1 x RS-232/422/485, (COM1, adjusted by switch)1 x RS-232, COM2</td></tr><tr><td>Audio</td><td colspan="4">7.1 channel audio via 5 jacks and S/PDIF output</td></tr><tr><td colspan="5">Power Supply</td></tr><tr><td>DC input</td><td colspan="4">24V DC</td></tr><tr><td colspan="5">Physical</td></tr><tr><td>Dimension</td><td colspan="4">232W x 180.8D x 82.8H mm (9.1 x 7.1 x 3.2 in)</td></tr><tr><td>Weight</td><td colspan="4">3kg (6.6bs)</td></tr><tr><td>Mount</td><td colspan="4">DIN rail or wall-mount</td></tr><tr><td colspan="5">Environmental</td></tr><tr><td>Operating Temperature</td><td colspan="4">0 to 55°C</td></tr><tr><td>Storage Temperature</td><td colspan="4">-20 to 85°C (-4°F to 185°F)</td></tr><tr><td>Humidity</td><td colspan="4">Approx. 90% @40°C (non-condensing)</td></tr><tr><td>Vibration</td><td colspan="4">Operating 0.5 Grms, 5-500 Hz, 3 axes w/HDDOperating 1 Grms, 5-500 Hz, 3 axes w/ SSD</td></tr><tr><td>Shock</td><td colspan="4">Operating 20G, half sine 11 ms duration</td></tr><tr><td>EMC</td><td colspan="4">CE &amp; FCC Class A</td></tr><tr><td>Safety</td><td colspan="4">CE/LVD, UL, CB</td></tr></table>

<table><tr><td colspan="3">Power Consumption</td></tr><tr><td>Power off</td><td>1.2W(0.05A@24VDC)</td><td>In shutdown mode with DC input and only USB keyboard/mouse</td></tr><tr><td>System idle</td><td>21W(0.86A@24VDC)</td><td>Under Windows Desktop with no application programs executed</td></tr><tr><td>System full load</td><td>164W(6.81A@24VDC)</td><td>► Total PoE loading is 32W► Dummy load of 4.5W in connection to represent each USB 3.0 load► Dummy load of 2.5W in connection to represent each USB 2.0 load► HDD permanently accessed► CPU(i7-6700) @ 100% loading (by Burn-in test program)</td></tr><tr><td>Recommended power supply</td><td>180W</td><td></td></tr></table>

# 1.3 Mechanical Drawings

![The image displays a white document icon featuring a folded top-left corner and horizontal lines near the bottom. A large, red checkmark is superimposed over the center of the document.](.eos-1300-50-1z222-2000-200-en/7a2c7fec48600765d5134721966f2e42d654ff7bde14c70981b498fd26c87a84.jpg)
NOTE:

All dimensions shown are in millimeters (mm) unless otherwise stated.

![180.8\n190.5](.eos-1300-50-1z222-2000-200-en/93f6b3519e4b61d287ce7cab04df5fff24d8925617a9516646ed078fd17d627c.jpg)

Figure 1-1: Top View

![232\nADLINK\nTECHNOLOGY\nDP1\nDP2\nAudio\nI/O 1\nV1-\nV2-\n24V DC ... IN\n81.5\n82.8](.eos-1300-50-1z222-2000-200-en/d703ed5b699406f2008fd2e3bed2babb76cac9992326984b65e2e2b840fa65c0.jpg)

Figure 1-2: Front View

![Pure electrical circuit lines without any symbols](.eos-1300-50-1z222-2000-200-en/bb21c188d9c431b884a901d326283c71c8d852e8e160c24333cb1c78cdcaca7a.jpg)

Figure 1-3: Rear View

![4.25\n5.5](.eos-1300-50-1z222-2000-200-en/9633fc304b4e9b9d0c31cea84e3a32654aba3b8f809facd03d426179bfe17bab.jpg)

Figure 1-4: (Right) Side View

# 1.4 Front Panel I/O Connectors

![COM1\nCOM2\nI/O 2\nSS\nSS\nCL\nE5\nAudio\nI/O 1\nCH1\nCH2\nCH3\nCH4\nPWR\nStatus HDD\nV-\nV+\nADLINK\nTECHNOLOGY INC\nDP1\nDP2\n24V DC --- IN](.eos-1300-50-1z222-2000-200-en/0038cf13bb48bb3358f0741f8f2697e26f6710bc7722fcfa6b6a56868bd36fe6.jpg)

Figure 1-5: Front Panel I/O

I/O connectors and controls on the EOS-1300 front panel, as labeled, are as follows

▶ LED Indicators
▶ Power button
▶ Reset button
▶ DC power connector
▶ GigE camera port
▶ I/O 1, DB-26P Digital I/O connector
▶ Audio connectors, 7.1 channel audio via 5 jacks and S/PDIF output
▶ LAN ports, no PoE function
▶ USB2.0 ports
▶ Display ports
▶ USB3.0 ports
▶ COM1 and COM2, Serial ports
▶ I/O 2, DB-37P Digital I/O and Encoder Connector

# 1.4.1 LED Indicators

In addition to the LED of the power button, LEDs on the front panel indicating operations as follows.

<table><tr><td>LED</td><td>Color</td><td>Lit</td><td>Off</td></tr><tr><td>PWR Status</td><td>Amber</td><td>System is operating</td><td>System is in sleep (S1/S3), hibernate (S4), or power off (S5) state</td></tr><tr><td>HDD</td><td>Green</td><td>SATA hard drive is active</td><td>N/A</td></tr></table>

Table 1-1: LED Indicator Legend

# 1.4.2 Power Button

Push button with blue LED indicator. System is turned on when button is pressed, and the power LED lit. If the system hangs, depressing the button for 5 seconds powers down the unit.

# 1.4.3 Reset Button

Executes hard reset.

# 1.4.4 DC Power Connector

Consists of V+, chassis ground, and V- pins. V+ and V- pins accept DC power input and chassis ground pin enhances EMC compatibility. The DC power input accepts 24 VDC input.

![V-\nV+\n3\n2\n1\n24V DC --- IN](.eos-1300-50-1z222-2000-200-en/22c97d754a1fe44e2d11324a3c5e64dd6d3cefee9dffcfd2893baa3eac87bc76.jpg)

Figure 1-6: Power Supply Connector Pin Assignments

<table><tr><td>Pin</td><td>Signal</td></tr><tr><td>1</td><td>V+(DC_IN)</td></tr><tr><td>2</td><td>GND(CHGND)</td></tr><tr><td>3</td><td>V- (DGND)</td></tr></table>

Table 1-2: DC Power Supply Connector Signals

# 1.4.5 GigE Camera Port

CH1 to CH4 connect GigE cameras and support PoE (Power over Ethernet) functions, with support as follows.

▶ 4x fully-integrated Gigabit Ethernet Media Access Control (MAC) and physical layer (PHY) ports
▶ IEEE 802.3.af compliant for up to 8 W/channel with power up to 48 V over existing CAT-5e Ethernet infrastructure with no need for modification
▶ Standard IEEE 802.3 Ethernet interface for 1000BASE-T, 100BASE-TX, and 10BASE-T applications
▶ Smart PoE function provides manual power down of PoE supply with software API
▶ 9 kB jumbo frame support

![LED1\nLED2\n8\n1](.eos-1300-50-1z222-2000-200-en/4a997351cb6c59ce697c1265c60bd263968359e5244879023c2f19826e8a090a.jpg)

Figure 1-7: GigE Camera Port

<table><tr><td>Pin</td><td>Signal</td></tr><tr><td>1</td><td>MDI0+ (PoE_DC48V)</td></tr><tr><td>2</td><td>MDI0- (PoE_DC48V)</td></tr><tr><td>3</td><td>MDI1+ (PoE_DC0V)</td></tr><tr><td>4</td><td>MDI2+ (PoE_DC48V)</td></tr><tr><td>5</td><td>MDI2- (PoE_DC48V)</td></tr><tr><td>6</td><td>MDI1- (PoE_DC0V)</td></tr><tr><td>7</td><td>MDI3+ (PoE_DC0V)</td></tr></table>

<table><tr><td>Pin</td><td>Signal</td></tr><tr><td>8</td><td>MDI3- (PoE_DC0V)</td></tr></table>

Table 1-3: GigE Camera Port Pin Assignments

<table><tr><td>LED</td><td>Color</td><td>Activity</td><td></td></tr><tr><td rowspan="3">LED1 (Speed)</td><td rowspan="3">Green/ Yellow</td><td>Unlit</td><td>10Mbps</td></tr><tr><td>Green</td><td>100Mbps</td></tr><tr><td>Yellow</td><td>1000Mbps</td></tr><tr><td rowspan="3">LED2 (Active/Link)</td><td rowspan="3">Green</td><td>Unlit</td><td>Ethernet port is disconnected</td></tr><tr><td>Lit</td><td>Ethernet port is connected with no activity</td></tr><tr><td>Flashing</td><td>Ethernet port is connected and active</td></tr></table>

Table 1-4: LED Indicator Legend

# 1.4.6 Digital I/O and Encoder Connectors (I/O1 and I/O2)

I/O1 is a DB-26P connector receiving 8CH isolated digital input (DI CH0 to 7) and 8CH isolated digital output (DO CH0 to 7). DI/O channels 0 to 3 can be configured to trigger I/O via API (see EOS-1300 Function Library Reference document).

![9\n1\n18\n10\n26\n19](.eos-1300-50-1z222-2000-200-en/0fab04589a27a559499c023a54cc795511a5055034f9525dcee33e37a94af3f9.jpg)

Figure 1-8: I/O1, DB-26P Digital I/O Connector

<table><tr><td>Pin</td><td>Signal</td><td>Pin</td><td>Signal</td></tr><tr><td>1</td><td>IDI_0H</td><td>14</td><td>IDO_2</td></tr><tr><td>2</td><td>IDI_1H</td><td>15</td><td>IDO_2_COM</td></tr><tr><td>3</td><td>IDI_2H</td><td>16</td><td>IDO_3</td></tr><tr><td>4</td><td>IDI_3H</td><td>17</td><td>IDO_3_COM</td></tr><tr><td>5</td><td>IDI_0_1_2_3L</td><td>18</td><td>IDI_4_5_6_7L</td></tr><tr><td>6</td><td>IDI_4H</td><td>19</td><td>IDO_4</td></tr><tr><td>7</td><td>IDI_5H</td><td>20</td><td>IDO_4_COM</td></tr><tr><td>8</td><td>IDI_6H</td><td>21</td><td>IDO_5</td></tr><tr><td>9</td><td>IDI_7H</td><td>22</td><td>IDO_5_COM</td></tr><tr><td>10</td><td>IDO_0</td><td>23</td><td>IDO_6</td></tr><tr><td>11</td><td>IDO_0_COM</td><td>24</td><td>IDO_6_COM</td></tr><tr><td>12</td><td>IDO_1</td><td>25</td><td>IDO_7</td></tr><tr><td>13</td><td>IDO_0_COM</td><td>26</td><td>IDO_7_COM</td></tr></table>

Table 1-5: I/O1, DB-26P Connector Pin Assignments

I/O2 is a DB-37P connector receiving 4CH isolated digital input (DI CH8 to 11), 8CH isolated digital output (DO CH8 to 15), with 2CH isolated Encoder General Purpose input/output application with isolation requirement recommended.

![19\n1\n37\n20](.eos-1300-50-1z222-2000-200-en/a00278ab49d32bcf178d9121fa3f3d8f566b25b60d9ce54c2e8a109e142d160d.jpg)

Figure 1-9: I/O2, DB-37P Digital I/O and Encoder Connector

<table><tr><td>Pin</td><td>Signal</td><td>Pin</td><td>Signal</td></tr><tr><td>1</td><td>IDI_8H</td><td>20</td><td>IDI_9H</td></tr><tr><td>2</td><td>IDI_10H</td><td>21</td><td>IDI_11H</td></tr><tr><td>3</td><td>IDI_8_9_10_11L</td><td>22</td><td>IDO_8</td></tr><tr><td>4</td><td>IDO_8_COM</td><td>23</td><td>IDO_9</td></tr><tr><td>5</td><td>IDO_9_COM</td><td>24</td><td>IDO_10</td></tr><tr><td>6</td><td>IDO_10_COM</td><td>25</td><td>IDO_11</td></tr><tr><td>7</td><td>IDO_11_COM</td><td>26</td><td>IDO_12</td></tr><tr><td>8</td><td>IDO_12_COM</td><td>27</td><td>IDO_13</td></tr><tr><td>9</td><td>IDO_13_COM</td><td>28</td><td>IDO_14</td></tr><tr><td>10</td><td>IDO_14_COM</td><td>29</td><td>IDO_15</td></tr><tr><td>11</td><td>IDO_15_COM</td><td>30</td><td>EA1+</td></tr><tr><td>12</td><td>EA0+</td><td>31</td><td>EA1-</td></tr><tr><td>13</td><td>EA0-</td><td>32</td><td>EB1+</td></tr><tr><td>14</td><td>EB0+</td><td>33</td><td>EB1-</td></tr><tr><td>15</td><td>EB0-</td><td>34</td><td>EZ1+</td></tr><tr><td>16</td><td>EZ0+</td><td>35</td><td>EZ1-</td></tr><tr><td>17</td><td>EZ0-</td><td>36</td><td>N/A</td></tr><tr><td>18</td><td>N/A</td><td>37</td><td>N/A</td></tr><tr><td>19</td><td>N/A</td><td></td><td></td></tr></table>

Table 1-6: I/O2 DB-37P Connector Pin Assignments

DI/O and Encoder Electrical Specifications

<table><tr><td colspan="2">12CH Isolation DI</td></tr><tr><td>Logic high</td><td>5 to 24V</td></tr><tr><td>Logic low</td><td>0 to 0.8V</td></tr><tr><td>Input resistance</td><td>2.4kΩ @ 1W</td></tr><tr><td>Isolation voltage</td><td>1.5kV DC channel 0 to 11</td></tr><tr><td>Maximum delay</td><td>Opto-isolator turn on: 15μsOpto-isolator turn off: 150μs</td></tr><tr><td>Recommended input current</td><td>5mA</td></tr></table>

<table><tr><td colspan="2">16CH Isolation D0</td></tr><tr><td>Logic high</td><td>Max. 30V</td></tr><tr><td>Logic low</td><td>Max. 3.5V @ 100mA</td></tr><tr><td>Sink/Source current</td><td>Max. 100mA</td></tr><tr><td>Isolation voltage</td><td>1.5kV DC channel 0 to 15</td></tr><tr><td>Maximum delay</td><td>Opto-isolator turn on: 25μsOpto-isolator turn off: 300μs</td></tr></table>

<table><tr><td colspan="2">2CH Encoder</td></tr><tr><td>Input voltage</td><td>5V ± 5%</td></tr><tr><td>Encoder frequency</td><td>Max. 50kHz</td></tr><tr><td>Encoder input</td><td>EA/EB</td></tr><tr><td>Encoder index</td><td>EZ</td></tr><tr><td>Isolation voltage</td><td>1.5kV DC channels 0 to 1</td></tr></table>

# 1.4.7 Serial ports (COM1 and COM2)

COM1 supports RS-232/422/485 based on switch setting on the mainboard, with RS-232 the default, and COM2 supports RS-232 only.

![1\n5\n6\n9](.eos-1300-50-1z222-2000-200-en/3601afdb39cdc1f987eab1599ac0ea1f1f4c9f67156586a4838ccd07e0ba57a4.jpg)

Figure 1-10: COM1 and COM2 Connectors

<table><tr><td>Pin</td><td colspan="3">Signal</td></tr><tr><td></td><td>RS232</td><td>RS422</td><td>RS485</td></tr><tr><td>1</td><td>DCD#</td><td>TXD422-</td><td>485DATA-</td></tr><tr><td>2</td><td>RXD</td><td>TXD422+</td><td>485DATA+</td></tr><tr><td>3</td><td>TXD</td><td>RXD422+</td><td>N/S</td></tr><tr><td>4</td><td>DTR#</td><td>RXD422-</td><td>N/S</td></tr><tr><td>5</td><td>GND</td><td>N/S</td><td>N/S</td></tr><tr><td>6</td><td>DSR#</td><td>N/S</td><td>N/S</td></tr><tr><td>7</td><td>RTS#</td><td>N/S</td><td>N/S</td></tr><tr><td>8</td><td>CTS#</td><td>N/S</td><td>N/S</td></tr><tr><td>9</td><td>RI#</td><td>N/S</td><td>N/S</td></tr></table>

Table 1-7: COM1 and COM2 Connectors Pin Assignments

# Setting COM1

COM1 can be set to RS-232/422/485 using switch SWS1M1, located on the mainboard as shown.

![1 2\n5 5\nNO](.eos-1300-50-1z222-2000-200-en/462d496ba636f34fd00cece095b96a743f910fe3d466a1ae3a2ebc83e5ccfbe1.jpg)

Figure 1-11: SWS1M1 Switch

![Close-up of a computer motherboard with a cooling fan and CPU socket, no visible text or symbols on the main components.](.eos-1300-50-1z222-2000-200-en/b488bae81ace95b8daaec3cc154ebfe71759311fc3f03a300a481e4b7bcb3ab9.jpg)

Figure 1-12: SWS1M1 Switch Location

Switch settings are as follows.

<table><tr><td></td><td>1</td><td>2</td></tr><tr><td>RS-232 (Default)</td><td>ON</td><td>OFF</td></tr><tr><td>RS-422</td><td>ON</td><td>ON</td></tr><tr><td>RS-485</td><td>OFF</td><td>ON</td></tr></table>

Table 1-8: SWS1M1 Switch Setting

# 1.4.8 LAN Ports

Two LAN Ethernet controllers based on Intel® i219LM/i211AT both support up to 1Gb/s.

![LED1\nLED2\n8\n1](.eos-1300-50-1z222-2000-200-en/fa9dda99ffd9067d12ae0e96c0a7b5d7ff0550149f7934099098998f88f0c0f0.jpg)

Figure 1-13: LAN Port

<table><tr><td>Pin</td><td>10BASE-T/100BASE-TX</td><td>1000BASE-T</td></tr><tr><td>1</td><td>TX+</td><td>LAN_MDIO+</td></tr><tr><td>2</td><td>TX-</td><td>LAN_MDIO-</td></tr><tr><td>3</td><td>RX+</td><td>LAN_MDI1+</td></tr><tr><td>4</td><td>N/A</td><td>LAN_MDI2+</td></tr><tr><td>5</td><td>N/A</td><td>LAN_MDI2-</td></tr><tr><td>6</td><td>RX-</td><td>LAN_MDI1-</td></tr><tr><td>7</td><td>N/A</td><td>LAN_MDI3+</td></tr><tr><td>8</td><td>N/A</td><td>LAN_MDI3-</td></tr></table>

Table 1-9: LAN Port Pin Definitions

<table><tr><td>LED</td><td>Activity</td><td></td></tr><tr><td rowspan="3">LED1(Active/Link)</td><td>Off</td><td>No Link</td></tr><tr><td>Orange</td><td>Link Active</td></tr><tr><td>Blinking</td><td>Data Activity</td></tr><tr><td rowspan="3">LED2(Speed)</td><td>Off</td><td>10 Mb connection</td></tr><tr><td>Green</td><td>100 Mb connection</td></tr><tr><td>Orange</td><td>1 Gb connection</td></tr></table>

Table 1-10: LAN Port LED Legend

# 1.4.9 DisplayPort Connectors

Two DisplayPort v1.1 connections support up to 3840x2160 @ 30Hz.

![19\n1\n20\n2](.eos-1300-50-1z222-2000-200-en/2f25c964a05ffce812f899fe1f41443795bac164729ceda43e9882a92a2798db.jpg)

Figure 1-14: DisplayPort Connector

<table><tr><td>Pin</td><td>Signal</td><td>Pin</td><td>Signal</td></tr><tr><td>1</td><td>CN_DP0_P</td><td>2</td><td>GND</td></tr><tr><td>3</td><td>CN_DP0_N</td><td>4</td><td>CN_DP1_P</td></tr><tr><td>5</td><td>GND</td><td>6</td><td>CN_DP1_N</td></tr><tr><td>7</td><td>CN_DP2_P</td><td>8</td><td>GND</td></tr><tr><td>9</td><td>CN_DP2_N</td><td>10</td><td>CN_DP3_P</td></tr><tr><td>11</td><td>GND</td><td>12</td><td>CN_DP3_N</td></tr><tr><td>13</td><td>CN_CAD-L</td><td>14</td><td>CN_CEC</td></tr><tr><td>15</td><td>CN_AUX_P</td><td>16</td><td>GND</td></tr><tr><td>17</td><td>CN_AUX_N</td><td>18</td><td>DDP_HPD</td></tr><tr><td>19</td><td>GND</td><td>20</td><td>P3V3</td></tr></table>

Table 1-11: DisplayPort Pin Assignment

# 1.4.10 USB Ports

4 USB 3.0 and 4 USB 2.0 ports each provide 5V power for connected devices.

![1\n4](.eos-1300-50-1z222-2000-200-en/d1976655af52eeb88f897dbd54b07315e2154612e0f818260b19b1c5dfe92dcb.jpg)

Figure 1-15: USB 2.0

<table><tr><td>Pin</td><td>Signal</td></tr><tr><td>1</td><td>Vcc</td></tr><tr><td>2</td><td>UV0-</td></tr><tr><td>3</td><td>UV0+</td></tr><tr><td>4</td><td>GNE</td></tr></table>

Table 1-12: USB 2.0 Pin Assignments

![9\n5\n1\n4](.eos-1300-50-1z222-2000-200-en/c25beaa760b339de17ece518815884ee06ecd4bb1d6800fcf5bf4bb2b292bc51.jpg)

Figure 1-16: USB 3.0

<table><tr><td>Pin</td><td>Signal</td></tr><tr><td>1</td><td>USB3.0_P5VA</td></tr><tr><td>2</td><td>USB2_CMAN</td></tr><tr><td>3</td><td>USB2_CMAP</td></tr><tr><td>4</td><td>GND</td></tr><tr><td>5</td><td>USB3A_CMRXN</td></tr><tr><td>6</td><td>USB3A_CMRXP</td></tr><tr><td>7</td><td>GND</td></tr></table>

<table><tr><td>Pin</td><td>Signal</td></tr><tr><td>8</td><td>USB3A_CMTXN</td></tr><tr><td>9</td><td>USB3A_CMTXP</td></tr></table>

Table 1-13: USB 3.0 Pin Assignments

# 1.5 DI/O and Encoder Sample Circuits

# 1.5.1 Isolated Digital Input Circuits

The input can accept voltages up to 24V, with extra 2.4kΩ input resistors (Rs). Connections between outside signals are as follows.

![3.3V\nIDI\nOpto-\nisolators\n2.4kΩ\nIDI_H\nRs\n+\nIDI_L](.eos-1300-50-1z222-2000-200-en/e5131611dbd369c2cd0b06a9c57ab463085f4a00112fac31c3731fdabdabb5f9.jpg)

Figure 1-17: Digital Input Sample Application Circuit

# 1.5.2 Isolated Digital Output Circuits

Outputs 0 to 15 provide up to 100mA current (maximum). These outputs are typically connected (directly or indirectly) to other devices, such as a trigger input, PLC input, relay, or indicator light.

![Opto-\nisolators\n2.26kΩ\nPTC\nIDO_COM\nIDO\nDevice\n2.26kΩ](.eos-1300-50-1z222-2000-200-en/c25c3434026e2871e3f735157a96368c1406fe342a97255675b495a1b611c621.jpg)

Figure 1-18: Digital Output Sample Application Circuit for Sink Type

![Opto-\nisolators\n2.26kΩ\nPTC\nIDO_COM\nIDO\nDevice\n+\n-\n2.26kΩ](.eos-1300-50-1z222-2000-200-en/7b4c7985641f4d3c882ae48da9b5ee245a3b5735febbd005fc9bf4b58b2c3698.jpg)

Figure 1-19: Digital Output Sample Application Circuit for Source Type

# 1.5.3 Isolated Encoder Input Circuits

Encoder inputs can connect to either a single-ended or differential encoder. Using an encoder allows input and output delay values to be specified in pulse counts rather than real time units.

![EA/EB/EZ\nOpto-isolators\nEA+/EB+/EZ+\nR=330Ω\nC=100pF\nEA-/EB-/EZ-\nExternal Encoder\nwith line driver\noutput\nA/B/Z phase\nsignal](.eos-1300-50-1z222-2000-200-en/6b9a3328ce593e47db06d3bc1d3eab33dd54e0d960f4cd32043c8220978eb236.jpg)

Figure 1-20: Encoder Input Sample Application Circuit for Line Driver

![This diagram illustrates an interface circuit, divided by a vertical dotted line into an internal block (left) and an external section (right).\n\n**Left Section (Internal Circuit):**\n*   **Opto-isolators Block:** A smaller box labeled 'Opto-isolators' contains an inverter symbol (triangle with a circle) connected in series with an LED symbol.\n    *   An input line labeled **EA/EB/EZ** connects to the inverter input.\n    *   The inverter output connects to the LED anode.\n    *   The LED cathode connects to the bottom horizontal wire.\n*   **Resistor and Filter:**\n    *   A top horizontal wire is labeled **EA+/EB+/EZ+**. It contains a resistor labeled **R=330Ω**.\n    *   A bottom horizontal wire is labeled **EA-/EB-/EZ-**.\n    *   Connected in parallel across the top and bottom wires (to the right of the resistor) are a diode and a capacitor labeled **C=100pF**.\n\n**Right Section (External):**\n*   **Power and Encoder:**\n    *   A box labeled **5V External Power GND**.\n    *   Text reads **External Encoder with open collector output**.\n*   **Transistor:** An NPN transistor symbol is shown.\n    *   The base is connected to a line labeled **A/B/Z phase signal**.\n    *   The emitter connects to the bottom horizontal wire (**EA-/EB-/EZ-**).\n    *   The collector connects to the top horizontal wire (to the right of the resistor).\n\n**Connections:**\n*   The top wire (to the right of the resistor) connects to the **5V External Power GND** box and the collector of the external transistor.\n*   The bottom wire connects to the emitter of the external transistor.\n*   The dotted line separates the internal circuitry from the external power and encoder connections.](.eos-1300-50-1z222-2000-200-en/acb9d512e5f37542725fff1bdb82b2965f8af961b20fd59acfcf516da9b2dc3c.jpg)

Figure 1-21: Encoder Input Sample Application Circuit for Open Collector

This page intentionally left blank.

# 2 Getting Started

# 2.1 Unpacking Checklist

Before unpacking, check the shipping carton for any damage. If the shipping carton and/or contents are damaged, inform your dealer immediately. Retain the shipping carton and packing materials for inspection. Obtain authorization from your dealer before returning any product to ADLINK. Ensure that the following items are included in the package.

▶ EOS-1300
▶ Quick Start Guide

# 2.2 Adaptors & Additional Accessories

Device adaptors and other optional accessories should only be obtained through your ADLINK dealer. For more information, see "Getting Service" on page 73.

# 2.3 Installing Memory

1. Remove the top cover thumbscrews by hand or screw-driver.

![Exterior view of a gray server rack unit with ventilation grilles and mounting holes (no visible text or symbols)](.eos-1300-50-1z222-2000-200-en/05f12bca456b8cc4bdecd45f8d66d03b5fb57fae331a63d6ef3a71beb4013d23.jpg)

# 2. Remove the top cover.

![COM1\nCOM2\nI/O 2\nSPC\nSPD\nR\nAudio\nI/O 1\nCH1\nCH2\nCH3\nCH4\nPWR\nHDD\nMbit\nV-\nV+\n24V DC ... IN\nADLINK\nDP1 DP2](.eos-1300-50-1z222-2000-200-en/a0a642347a8149c63f75c01a3077e7e698028f1e8df3899b1bad106e76c8f79e.jpg)

3. Insert the memory module into the DDR4 SO-DIMM socket and press down until the module is properly seated and the retaining clips close on the module.

![4GB DDR4 2133 SODIMM\nM50-4GSSNCRG\ninnodisk\nM2A11512210690069 RD](.eos-1300-50-1z222-2000-200-en/8d94ed64f4d022fac8608e85a82ee69ce20234cb3241e9e07e34cea0b3138e32.jpg)

![4GB DDR4 2133 SODIMM\nM850-4GSSNCRG\n(0x16)\nM2A11512210690060 80\nInnodisk](.eos-1300-50-1z222-2000-200-en/11a7054ed3d9bf4961c75440759ef43bb6b22983e416d4cf46f7331e75781554.jpg)

# 2.4 Installing a Hard Disk or SS Drive

1. Remove the top cover as detailed previously.
2. Unplug the SATA cable.

![Close-up of a computer motherboard with visible CPU fan, power cord, and circuit board (no readable text or symbols)](.eos-1300-50-1z222-2000-200-en/2b94bb93b8f91d2b4928d440c1f961e78ded51fd0a45fae580889ea5272a4614.jpg)

3. Remove the two screws from the case underside.

![Back view of a computer chassis with two red-circled ports and mounting holes (no visible text or symbols)](.eos-1300-50-1z222-2000-200-en/737eca0af618291ca8999a8656e70d66d23fe073394d70ce9e0a6df8d6302a9c.jpg)

4. Remove the two screws fixing the drive bracket.

![Internal view of a computer motherboard showing a CPU fan, cooling unit, and wiring (no visible text or symbols)](.eos-1300-50-1z222-2000-200-en/c0c36837f63088277b457c4683f5ebc0c36b6fba565c4ad45066ca5d91d21fb0.jpg)

5. Withdraw the bracket and remove the four bracket screws.

![Metallic electronic component with four mounting holes and red-circled features (no text or symbols visible)](.eos-1300-50-1z222-2000-200-en/07c343dba9f574109fee4d28b55939a70366db3a4b0690726068b4b4989e1876.jpg)

6. Remove and/or replace the drive, secure the drive, and note the orientation.

![Transcend®\n2.5' SATA-2 SSD\nTS64GSSD630\n0 760557 824725\nS/N:B97885-0151\n64GB (LBA 125045,424)\nHW6290-S2\nMLC\nDC+6V=0.8A\n1505\nMade in Taiwan\n創見固態硬碟\nWARNING\n• Contains parts susceptible to damage by Electrostatic\nDischarge (ESD)\n• Product warranty will be void if label or cover is removed\nCEFCO® RoHS COMPLIANT](.eos-1300-50-1z222-2000-200-en/1e23f83314064dbf1a06d5c4d65c9f0f697f545516218686d3e4866793ac492a.jpg)

![2.5 SATA-2 SSD\nTSG4GSS630\nQ18897824725\nEN18897824725\nEN18897824725\nEN18897824725\nEN18897824725\nEN18897824725\nEN18897824725\nEN18897824725\nEN18897824](.eos-1300-50-1z222-2000-200-en/28ee48d61caab48a3282504df67499f2c6d276b067faea78b4d692c61ce4fda3.jpg)

7. Replace the four bracket screws.
8. Replace and secure the SSD or HDD bracket, and fasten the fixing screws.
9. Replace the case underside screws.
10. Insert and secure the SATA cable.
11. Replace the top cover.

# 2.5 Installing the Internal USB Dongle

1. Remove the top cover as detailed previously.
2. Plug the USB dongle into the USB port.

![Close-up of an electronic circuit board with visible traces and components, no readable text or symbols present.](.eos-1300-50-1z222-2000-200-en/7aeb5ccb64e3527de5ffdcf3db5a6ef8af6ace071a2798c220698db8cbfa9903.jpg)

# 2.6 Installing Wall-mount Brackets

Secure the provided wall-mount brackets in the four screw holes in the underside of the chassis, as shown.

![3D diagram of a computer chassis with red arrows pointing to camera components (no text or symbols present)](.eos-1300-50-1z222-2000-200-en/bf37b3fcde24b0399296f44e34000d4f48fac35b11c95c08eb3f000eae0b2623.jpg)

# 2.7 Installing DIN Rail Bracket

Secure the provided DIN rail bracket via the two screw holes on the rear side of the chassis, as shown.

![3D diagram of a black computer case with ventilation grilles and a close-up view showing internal components (no text or symbols)](.eos-1300-50-1z222-2000-200-en/af05e8557c8e40cdcbd5d883289cf59fb010509d63f9ad4293c76ebb2a54adaf.jpg)

# 2.8 Cooling Considerations

To maximize the efficiency of fan-based heat dissipation, maintain a minimum 3cm (1.2 inches) clearance from the top vents and 5cm (2 inches) from the side vents.

# 2.9 Driver Installation

![The image displays a simple icon representing a document or note. It features a white sheet of paper with a folded top-left corner (a 'dog-ear'). Horizontal grey lines run across the lower portion of the page, resembling ruled paper. A large, bold red checkmark is superimposed over the center of the document. There is no text visible in the image.](.eos-1300-50-1z222-2000-200-en/be9cf77d7001186193c5f2cc35483fbf4bc67f663595e49323ce83e61a103793.jpg)
NOTE:

Due to lack of controller support under Windows 7, successful OS installation may be prevented. For available solutions, please contact your ADLINK representative.

Download requisite drivers, as follows, for your system from http://www.adlinktech.com and install.

▶ Chipset
▶ Graphics
▶ IRST
▶ LAN
▶ Audio
▶ USB3
▶ KMDF (Only if Windows 7 is installed)
▶ ME
▶ Serial I/O (Only if Windows 8.1/10 is installed)
▶ DI/O

# Appendix A BIOS Setup

![This is an icon depicting a white document with a black outline and a folded top-right corner. Horizontal lines suggest text, and a large red checkmark is centered over the document.](.eos-1300-50-1z222-2000-200-en/295f77087e174634465db7816713d21c5387165e1406cb28a7703a907cceda7d.jpg)
NOTE:

BIOS options in the manual are for reference only, and are subject to configuration.

The Basic Input/Output System (BIOS) is a program that provides a basic level of communication between the processor and peripherals. In addition, the BIOS also contains codes for various advanced features applied to the EOS-1300. The BIOS setup program includes menus for configuring settings and enabling features of the EOS-1300 series. Most users do not need to use the BIOS setup program, as the EOS-1300 ships with default settings that work well for most configurations.

Enter BIOS setup by selecting DEL when the system is powered on the POST (Power On Self Test) message is displayed. The EOS-1300 controller supports one-time Boot Menu allowing selection of boot device. Enter the Boot Menu by selecting F7 at POST.

![The image displays a graphic of a white document featuring a curled top-left corner and faint grey horizontal lines running across the page. A large, bold red check mark is superimposed over the document, angling from the bottom left to the top right.](.eos-1300-50-1z222-2000-200-en/e0a56fd3c4c30442c139747bc26b0e9cee776242d346c3471f1eb82d46cd60ba.jpg)
NOTE:

▶ BIOS options listed are for reference only.
▶ Different configurations can affect BIOS behavior.
▶ Displayed material may reflect only the BIOS version corresponding to initial release and may differ from that of the purchased motherboard.

# A.1 Main

<table><tr><td>System Information Project Version Build Date and Time</td><td>EOS-1300 1.08.10 06/23/2016 16:28:56</td><td>System Management</td></tr><tr><td>Processor Information Brand String</td><td>Intel(R) Core(TM) i3-6100 CPU @ 3.70GHz</td><td></td></tr><tr><td>Frequency Processor ID Stepping Number of Processors GT Info</td><td>3700 MHz 506E3 R0/S0/N0 2Core(s) / 4Thread(s) GT2 (1050 MHz)</td><td></td></tr><tr><td>IGFX VBIOS Version Total Memory</td><td>1036 16384 MB</td><td>+: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save &amp; Exit ESC: Exit</td></tr><tr><td>PCH Information Name PCH SKU Stepping LAN PHY Revision ME FW Version ME Firmware SKU</td><td>SKL PCH-H PCH-H Desktop H110 SKU 31/D1 B2 11.0.0.1202 Consumer SKU</td><td></td></tr><tr><td>Access Level</td><td>Administrator</td><td></td></tr></table>

![Aptio Setup Utility - Copyright (C) 2016 American Megatrends, Inc.\nMain Advanced Security Boot Save & Exit\nBrand String Intel(R) Core(TM)\ni3-6100 CPU @ 3.70GHz\nFrequency 3700 MHz\nProcessor ID 506E3\nStepping R0/S0/N0\nNumber of Processors 2Core(s) / 4Thread(s)\nGT Info GT2 (1050 MHz)\nIGFX VBIOS Version 1036\nTotal Memory 16384 MB\nPCH Information\nName SKL PCH-H\nPCH SKU PCH-H Desktop H110 SKU\nStepping 31/D1\nLAN PHY Revision B2\nME FW Version 11.0.0.1202\nME Firmware SKU Consumer SKU\nAccess Level Administrator\nSystem Management\nSystem Date (Wed 07/27/2016)\nSystem Time (16:20:50)\nSet the Time. Use Tab to\nswitch between Time elements.\n+: Select Screen\n↑↓: Select Item\nEnter: Select\n+/-: Change Opt.\nF1: General Help\nF2: Previous Values\nF3: Optimized Defaults\nF4: Save & Exit\nESC: Exit\nVersion 2.17.1255. Copyright (C) 2016 American Megatrends, Inc.](.eos-1300-50-1z222-2000-200-en/1f7408d3798328179739ca81dfac4303cd5a711416ea5e23395ac54f150183f7.jpg)

# System Information

Shows current system project version, build date and time.

# Processor Information

Shows current system brand string, frequency, processor id, stepping, number of processors, GT info, IGFX VBIOS version, and total memory.

# PCH Information

Shows current system Name, PCH SKU, stepping, LAN PHY revision, ME FW version and ME firmware SKU.

# System Time/System Date

Changes system time and date. Highlight System Time or System Date using up or down Arrow keys. Enter new values using the keyboard then Enter. Use Tab to move between fields.

# A.1.1 System Management

<table><tr><td colspan="2">Main</td></tr><tr><td rowspan="2">System Management
Version: 1.00
Overview
► Board Information
System Health
► Temperatures and Fan Speed
► Power Consumption
► Runtime Statistics
► Flags
Hardware Controls
► Power Up
► Smart Fan</td><td>Board Information</td></tr><tr><td>+: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save &amp; Exit
ESC: Exit</td></tr><tr><td colspan="2">Version 2.17.1255. Copyright (C) 2016 American Megatrends, Inc.</td></tr></table>

# Board Information

Aptio Setup Utility - Copyright (C) 2016 American Megatrends, Inc.

Main

Board Information

<table><tr><td>SEMA Firmware</td><td>BMC EOS-1300 1v2</td></tr><tr><td>Build Date</td><td>Apr 20 2016</td></tr><tr><td>SEMA Bootloader</td><td>bl_EOS-1300 4v2</td></tr><tr><td>Build Date</td><td>Mar 18 2016</td></tr></table>

<table><tr><td>Hardware Version</td><td>7A104-0A20-120E</td></tr><tr><td>Serial Number</td><td>G5I9EA1004</td></tr><tr><td>Manufacturing Date</td><td>2016/07/01</td></tr><tr><td>Last Repair Date</td><td>0000/00/00</td></tr><tr><td>MAC ID</td><td>00306416E12C</td></tr></table>

SEMA Features:

<table><tr><td>Uptime &amp; Power Cycles Counter</td></tr><tr><td>System Restart Event</td></tr><tr><td>1024 Bytes User-Flash</td></tr><tr><td>Watchdog</td></tr><tr><td>Temperatures</td></tr><tr><td>Voltage Monitor</td></tr><tr><td>Display Backlight control</td></tr><tr><td>Power-Up Watchdog</td></tr><tr><td>Power Monitor (current sense)</td></tr><tr><td>Boot Counter</td></tr><tr><td>12V Input-Voltage</td></tr></table>

++: Select Screen

↑↓: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

Version 2.17.1255. Copyright (C) 2016 American Megatrends, Inc.

Aptio Setup Utility - Copyright (C) 2016 American Megatrends, Inc.

# Main

```csv
System Restart Event
1024 Bytes User-Flash
Watchdog
Temperatures
Voltage Monitor
Display Backlight control
Power-Up Watchdog
Power Monitor (current sense)
Boot Counter
12V Input-Voltage
4mR Rsense for Input-Voltage
Dual-BIOS
I2C bus 1
I2C bus 2
Programmable CPU fan
Programmable System fan
AT/ATX mode
ACPI Thermal Trigger
Power-Up to last state
Backlight restore
DTS register available
DTS offset registers programmable
Smart Fan3
TIVA GPIOs support
TIVA BMC
```

```txt
++: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
```

Version 2.17.1255. Copyright (C) 2016 American Megatrends, Inc.

Shows current system SEMA firmware, SEMA firmware build date, SEMA bootloader, SEMA bootloader build date, hardware version, serial number, manufacturing date, last repair date, MAC ID and SEMA features.

# Temperatures and Fan Speed

<table><tr><td colspan="2">Aptio Setup Utility - Copyright (C) 2016 American Megatrends, Inc.</td></tr><tr><td colspan="2">Main</td></tr><tr><td>Temperatures and Fan Speed</td><td></td></tr><tr><td>CPU Temperature</td><td></td></tr><tr><td>Current 40.5C</td><td></td></tr><tr><td>Startup 21C</td><td></td></tr><tr><td>Min 17C</td><td></td></tr><tr><td>Max 99C</td><td></td></tr><tr><td>Board Temperatures</td><td></td></tr><tr><td>Current 38C</td><td></td></tr><tr><td>Startup 23C</td><td></td></tr><tr><td>Min 19C</td><td></td></tr><tr><td>Max 67C</td><td></td></tr><tr><td>CPU Fan Speed 1152RPM</td><td>+: Select Screen↑↓: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF2: Previous ValuesF3: Optimized DefaultsF4: Save &amp; ExitESC: Exit</td></tr></table>

Shows current system CPU and board temperatures and CPU fan speed.

# Power Consumption

<table><tr><td colspan="2">Aptio Setup Utility - Copyright (C) 2016 American Megatrends, Inc.</td></tr><tr><td>Power Consumption</td><td></td></tr><tr><td>VCORE 1.248V
VGFX 0.012V
VMEM 1.196V
5VSB 4.989V
VIN (12V) 11.980V
5V 5.071V
3.3V 3.346V
3.3VSB 3.296V
RTC 3.038V
Input Current 2.630A</td><td>+: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save &amp; Exit
ESC: Exit</td></tr><tr><td colspan="2">Version 2.17.1255. Copyright (C) 2016 American Megatrends, Inc.</td></tr></table>

Shows current system VCORE, VGFX, VMEM, 5VSB, VIN (12V), 5V, 3.3V, 3.3VSB, RTC and input current.

# Runtime Statistics

<table><tr><td colspan="2">Aptio Setup Utility - Copyright (C) 2016 American Megatrends, Inc.</td></tr><tr><td>Main</td><td></td></tr><tr><td>Runtime Statistics</td><td></td></tr><tr><td>Total Runtime 326h 31m</td><td></td></tr><tr><td>Current Runtime 0h 11m 17s</td><td></td></tr><tr><td>Power Cycles 155</td><td></td></tr><tr><td>Boot Cycles 1645</td><td></td></tr><tr><td>Boot Reason Software-reset</td><td></td></tr><tr><td></td><td>+: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save &amp; Exit
ESC: Exit</td></tr><tr><td colspan="2">Version 2.17.1255. Copyright (C) 2016 American Megatrends, Inc.</td></tr></table>

Shows current system total runtime, current runtime, power cycles, boot cycles, and boot reason.

# Flags

<table><tr><td colspan="2">Main</td></tr><tr><td>Flags</td><td></td></tr><tr><td>BMC Flags 0x40
BIOS Select Standard BIOS
ATX/AT-Mode ATX-Mode
Exception Code 0x00</td><td></td></tr><tr><td></td><td>+: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save &amp; Exit
ESC: Exit</td></tr><tr><td colspan="2">Version 2.17.1255. Copyright (C) 2016 American Megatrends, Inc.</td></tr></table>

Shows current system BMC flags, BIOS select, ATX/AT-mode and exception code.

# Power Up

<table><tr><td colspan="2">Aptio Setup Utility - Copyright (C) 2016 American Megatrends, Inc.Main</td></tr><tr><td rowspan="2">Power UpPower-Up Watchdog [Disabled]ATTENTION: Pressing F12 during start up disables the Power Up Watchdog.</td><td>The Power Up Watchdog resets the system after a certain amount of time after power up.Pressing F12 during start up disables the Power Up Watchdog.</td></tr><tr><td>+: Select Screen↑↓: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF2: Previous ValuesF3: Optimized DefaultsF4: Save &amp; ExitESC: Exit</td></tr></table>

Enables/disables Power Up Watchdog reset of the system a certain amount of time after power up. Pressing F12 during startup disables Power Up Watchdog.

# Smart Fan

<table><tr><td colspan="2">Main</td></tr><tr><td>Smart Fan
CPU Fan Mode [AUTO (Smart Fan)]</td><td>CPU Fan Mode</td></tr><tr><td></td><td>+: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save &amp; Exit
ESC: Exit</td></tr><tr><td colspan="2">Version 2.17.1255. Copyright (C) 2016 American Megatrends, Inc.</td></tr></table>

Sets CPU fan mode from AUTO (Smart Fan) or Full Speed.

# A.2 Advanced

<table><tr><td colspan="2">Aptio Setup Utility - Copyright (C) 2016 American Megatrends, Inc.</td></tr><tr><td colspan="2">Main Advanced Security Boot Save &amp; Exit</td></tr><tr><td>CPU
SATA
Memory
Graphics
USB
Super IO
Serial Port Console
Network
Security</td><td>CPU Configuration Parameters</td></tr><tr><td></td><td>+: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save &amp; Exit
ESC: Exit</td></tr><tr><td colspan="2">Version 2.17.1255. Copyright (C) 2016 American Megatrends, Inc.</td></tr></table>

![The image displays a standard hazard warning sign featuring a yellow triangle with a thick black border. Inside the triangle is a large black exclamation point. Below the triangle, the text 'CAUTION:' is printed in black capital letters.](.eos-1300-50-1z222-2000-200-en/cc794a07887d944dfbf439dcc59c956dff5f7f35ec450ce5871192b0b4b6d3d6.jpg)

Setting incorrect or conflicting values in Advanced BIOS Setup may cause system malfunction

Accesses advanced options of the EOS-1300.

# A.2.1 CPU

Aptio Setup Utility - Copyright (C) 2016 American Megatrends, Inc.

Advanced

CPU

Intel(R) Core(TM) i3-6100 CPU @ 3.70GHz

CPU Signature 506E3

Microcode Patch 82

Max CPU Speed 3700 MHz

Min CPU Speed 800 MHz

CPU Speed 3700 MHz

Processor Cores 2

Hyper Threading Technology Supported

Intel VT-x Technology Supported

Intel SMX Technology Not Supported

64-bit Supported

EIST Technology Supported

CPU C3 state Supported

CPU C6 state Supported

CPU C7 state Supported

CPU C8 state Supported

CPU C9 state Not Supported

CPU C10 state Not Supported

L1 Data Cache 32 kB x 2

L1 Code Cache 32 kB x 2

L2 Cache 256 kB x 2

L3 Cache 3 MB

Disabled for Windows XP

++: Select Screen

↑↓: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

Version 2.17.1255. Copyright (C) 2016 American Megatrends, Inc.

Aptio Setup Utility - Copyright (C) 2016 American Megatrends, Inc.

Advanced

<table><tr><td>Intel SMX Technology</td><td>Not Supported</td></tr><tr><td>64-bit</td><td>Supported</td></tr><tr><td>EIST Technology</td><td>Supported</td></tr><tr><td>CPU C3 state</td><td>Supported</td></tr><tr><td>CPU C6 state</td><td>Supported</td></tr><tr><td>CPU C7 state</td><td>Supported</td></tr><tr><td>CPU C8 state</td><td>Supported</td></tr><tr><td>CPU C9 state</td><td>Not Supported</td></tr><tr><td>CPU C10 state</td><td>Not Supported</td></tr><tr><td>L1 Data Cache</td><td>32 kB × 2</td></tr><tr><td>L1 Code Cache</td><td>32 kB × 2</td></tr><tr><td>L2 Cache</td><td>256 kB × 2</td></tr><tr><td>L3 Cache</td><td>3 MB</td></tr><tr><td>L4 Cache</td><td>Not Present</td></tr><tr><td>Limit CPUID Maximum</td><td>[Disabled]</td></tr><tr><td>Execute Disable Bit</td><td>[Enabled]</td></tr><tr><td>Intel Virtualization Technology</td><td>[Enabled]</td></tr><tr><td>VT-d</td><td>[Enabled]</td></tr><tr><td>Intel(R) SpeedStep(tm)</td><td>[Enabled]</td></tr><tr><td>CPU C states</td><td>[Enabled]</td></tr><tr><td>Enhanced C-states</td><td>[Enabled]</td></tr><tr><td>Package C State limit</td><td>[AUTO]</td></tr><tr><td>ACPI 3.0 T-States</td><td>[Disabled]</td></tr></table>

Enable/Disable ACPI 3.0 T-States.

++: Select Screen

↑↓: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

Version 2.17.1255. Copyright (C) 2016 American Megatrends, Inc.

# Limit CPUID Maximum

Disabled for Windows XP.

# Execute Disable Bit

XD can prevent certain malicious buffer overflow attacks when combined with a supporting OS (Windows Server 2003 SP1, Windows XP SP2, SuSE Linux 9.2, or Red Hat Enterprise 3 Update 3).

# Intel® Virtualization Technology

When enabled, a VMM can utilize the additional hardware capabilities provided by Vanderpool Technology.

# VT-d

Enables/disables VT-d capability.

# Intel $^{®}$ SpeedStep(tm)

Allows more than two frequency ranges to be supported.

# Turbo Mode

Enables/disables Intel $^{®}$ TurboBoost Technology.

# CPU C states

Enables/disables CPU C states.

# Enhanced C-states

Enables/disables C1E. When enabled, CPU will switch to minimum speed when all cores enter C-State.

# Package C State limit

CPU package C state limit.

# ACPI 3.0 T-States

Enables/disables ACPI 3.0 T-States.

# A.2.2 SATA

<table><tr><td colspan="2">Aptio Setup Utility - Copyright (C) 2016 American Megatrends, Inc. Advanced</td></tr><tr><td>SATA
SATA Speed Selection [Default]
Serial ATA Port 0 2.5&quot; SATA SSD (32.0GB)
Software Preserve SUPPORTED</td><td>Indicates the maximum speed the SATA controller can support.
+: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save &amp; Exit
ESC: Exit</td></tr><tr><td colspan="2">Version 2.17.1255. Copyright (C) 2016 American Megatrends, Inc.</td></tr></table>

# SATA Speed Selection

Indicates the maximum speed the SATA controller can support.

# A.2.3 Memory

<table><tr><td colspan="2">Aptio Setup Utility - Copyright (C) 2016 American Megatrends, Inc. Advanced</td></tr><tr><td>Memory</td><td></td></tr><tr><td>Memory RC Version</td><td>1.9.0.0</td></tr><tr><td>Memory Frequency</td><td>2133 MHz</td></tr><tr><td>Total Memory</td><td>4096 MB</td></tr><tr><td>VDD</td><td>1200 mVolts</td></tr><tr><td>DIMM#0</td><td>4096 MB</td></tr><tr><td>DIMM#1</td><td>Not Present</td></tr><tr><td>Memory Timings (tCL-tRCD-tRP-tRAS)</td><td>15-15-15-36</td></tr><tr><td></td><td>+: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save &amp; Exit
ESC: Exit</td></tr><tr><td colspan="2">Version 2.17.1255. Copyright (C) 2016 American Megatrends, Inc.</td></tr></table>

Shows current system memory RC version and values for memory frequency, total memory, VDD, DIMM#0, DIMM#1 and Memory Timings (tCL-tRCD-tRP-tRAS).

# A.2.4 Graphics

<table><tr><td colspan="2">Aptio Setup Utility - Copyright (C) 2016 American Megatrends, Inc. Advanced</td></tr><tr><td>Graphics
IGFX VBIOS Version 1036
Graphics Turbo IMON Current 31
GTT Size [8MB]
Aperture Size [256MB]
DVMT Pre-Allocated [32M]
DVMT Total Gfx Mem [256M]
Gfx Low Power Mode [Enabled]</td><td>Graphics turbo IMON current values supported (14-31)</td></tr><tr><td></td><td>+: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save &amp; Exit
ESC: Exit</td></tr><tr><td colspan="2">Version 2.17.1255. Copyright (C) 2016 American Megatrends, Inc.</td></tr></table>

# Graphics Turbo IMON Current

Graphics turbo IMON current values supported (14-31).

# GTT Size

Sets GTT size.

# Aperture Size

Sets aperture size. OVer 4GB MMIO BIOS assignment is automatically enabled when selecting 2048MB aperture, when CSM support is disabled.

# DVMT Pre-Allocated

Sets DVMT 5.0 Pre-allocated (Fixed) graphics memory size used by the internal graphics device.

# DVMT Total Gfx Mem

Sets DVMT5.0 Total graphic memory size as used by the internal graphics device.

# Gfx Low Power Mode

Applicable for SFF only.

# A.2.5 USB

<table><tr><td colspan="2">Aptio Setup Utility - Copyright (C) 2016 American Megatrends, Inc. Advanced</td></tr><tr><td>USB Configuration
USB Module Version 14
USB Devices:
1 Drive, 1 Keyboard, 1 Mouse, 1 Hub
Legacy USB Support [Enabled]
XHCI Hand-off [Enabled]
USB Mass Storage Driver Support [Enabled]
Port 60/64 Emulation [Disabled]</td><td>Enables Legacy USB support.
AUTO option disables legacy support if no USB devices are connected. DISABLE option will keep USB devices available only for EFI applications.</td></tr><tr><td></td><td>+: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save &amp; Exit
ESC: Exit</td></tr><tr><td colspan="2">Version 2.17.1255. Copyright (C) 2016 American Megatrends, Inc.</td></tr></table>

# Legacy USB Support

Enables Legacy USB support, with AUTO disabling legacy support if no USB devices are connected and DISABLE keeping USB devices available only for EFI applications.

# XHCI Hand-Off

A workaround for OS without XHCI hand-off support, with XHCI ownership change claimed by XHCI driver.

# USB Mass Storage Driver Support

Enables/disables USB mass storage driver support.

# Port 60/64 Emulation

Enables I/O port 60h/64h emulation support, and should be enabled for complete USB keyboard legacy support for non-USB aware OS.

# A.2.6 Super IO

<table><tr><td colspan="2">Aptio Setup Utility - Copyright (C) 2016 American Megatrends, Inc.
Advanced</td></tr><tr><td>IT8783 Super IO Configuration
Super IO Chip IT8783
► Serial Port 1 Configuration
► Serial Port 2 Configuration</td><td>Set Parameters of Serial Port 1 (COMA)
+: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save &amp; Exit
ESC: Exit</td></tr><tr><td colspan="2">Version 2.17.1255. Copyright (C) 2016 American Megatrends, Inc.</td></tr></table>

Shows current system Super IO Chip, Serial Port 1 Configuration and Serial Port 2 Configuration.

# Serial Port 1 Configuration

<table><tr><td>Aptio Setup Utility - Copyright (C) 2016 American Megatrends, Inc. Advanced</td><td></td></tr><tr><td>Serial Port 1 Configuration Device Settings IO=3F8h; IRQ=4;</td><td></td></tr><tr><td></td><td>+: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save &amp; Exit ESC: Exit</td></tr><tr><td colspan="2">Version 2.17.1255. Copyright (C) 2016 American Megatrends, Inc.</td></tr></table>

# Serial Port 2 Configuration

<table><tr><td colspan="2">Aptio Setup Utility - Copyright (C) 2016 American Megatrends, Inc. Advanced</td></tr><tr><td>Serial Port 2 Configuration
Device Settings IO=2F8h; IRQ=3;</td><td></td></tr><tr><td></td><td>+: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save &amp; Exit
ESC: Exit</td></tr><tr><td colspan="2">Version 2.17.1255. Copyright (C) 2016 American Megatrends, Inc.</td></tr></table>

# A.2.7 Serial Port Console

<table><tr><td colspan="2">Aptio Setup Utility - Copyright (C) 2016 American Megatrends, Inc. Advanced</td></tr><tr><td>COM1
Console Redirection [Disabled]
► Console Redirection Settings</td><td rowspan="3">Console Redirection Enable or Disable.</td></tr><tr><td>COM2
Console Redirection [Disabled]
► Console Redirection Settings</td></tr><tr><td>Legacy Console Redirection
► Legacy Console Redirection Settings</td></tr><tr><td>Serial Port for Out-of-Band Management/
Windows Emergency Management Services (EMS)
Console Redirection [Disabled]
► Console Redirection Settings</td><td>+: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save &amp; Exit
ESC: Exit</td></tr><tr><td colspan="2">Version 2.17.1255. Copyright (C) 2016 American Megatrends, Inc.</td></tr></table>

# Console Redirection

Enables console redirection on COM 1 to 2 and EMS COM.

# Console Redirection Settings

Sets miscellaneous parameters for COM Ports 1 to 2 and EMS COM.

# Legacy Console Redirection Settings

Selects a COM port to display redirection of Legacy OS and Legacy OPROM Messages.

# A.2.8 Network

<table><tr><td colspan="2">Aptio Setup Utility - Copyright (C) 2016 American Megatrends, Inc. Advanced</td></tr><tr><td>Network
Network Stack [Disabled]
PCH LAN i219LM Controller [Enabled]
i219-LM Wake on LAN [Enabled]
PCH LAN i211 Controller [Enabled]</td><td>Enable/Disable UEFI Network Stack</td></tr><tr><td></td><td>+: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save &amp; Exit
ESC: Exit</td></tr><tr><td colspan="2">Version 2.17.1255. Copyright (C) 2016 American Megatrends, Inc.</td></tr></table>

# Network Stack

Enables/disables UEFI network stack.

# PCH LAN i219LM Controller

Enables/disables onboard NIC i219LM.

# i219-LM Wake on LAN

Enables/disables integrated LAN to wake the system. (The Wake On LAN cannot be disabled if ME is on at Sx state.)

# PCH LAN i211 Controller

Enables/disables onboard NIC i211.

# A.2.9 Security

<table><tr><td colspan="2">Aptio Setup Utility - Copyright (C) 2016 American Megatrends, Inc. Advanced</td></tr><tr><td rowspan="2">Security
► BIOS Security Configuration
► Trusted Computing</td><td>BIOS Security Configuration settings.</td></tr><tr><td>+: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save &amp; Exit
ESC: Exit</td></tr><tr><td colspan="2">Version 2.17.1255. Copyright (C) 2016 American Megatrends, Inc.</td></tr></table>

Displays current system BIOS security configuration and Trusted Computing settings.

# BIOS Security Configuration

<table><tr><td colspan="2">Main</td></tr><tr><td>BIOS Security Configuration
RTC Lock [Enabled]
BIOS Lock [Enabled]</td><td>Enable will lock bytes 38h-3Fh in the lower/upper 128-byte bank of RTC RAM.</td></tr><tr><td></td><td>+: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save &amp; Exit
ESC: Exit</td></tr><tr><td colspan="2">Version 2.17.1255. Copyright (C) 2016 American Megatrends, Inc.</td></tr></table>

# RTC Lock

When enabled, locks bytes 38h-3Fh in the lower/upper 128-byte bank of RTC RAM.

# BIOS Lock

Enables/disables PCH BIOS Lock Enable (BLE bit).

# Trusted Computing

<table><tr><td colspan="2">Aptio Setup Utility - Copyright (C) 2016 American Megatrends, Inc. Advanced</td></tr><tr><td>ConfigurationSecurity Device Support [Enable]TPM State [Enabled]Pending operation [None]Device Select [Auto]Current Status InformationTPM Enabled Status: [Enabled]TPM Active Status: [Activated]TPM Owner Status: [Owned]</td><td>Enables or Disables BIOS support for security device.O.S. will not show Security Device. TCG EFI protocol and INT1A interface will not be available.+: Select Screen↑↓: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF2: Previous ValuesF3: Optimized DefaultsF4: Save &amp; ExitESC: Exit</td></tr></table>

# Security Device Support

Enables/disables BIOS support for security device, with OS not showing Security Device and TCG EFI protocol and INT1A interface unavailable.

# TPM State

Enables/disables Security Device. Computer will reboot during restart in order to change State of the Device.

# Pending operation

Schedules operations for the Security Device. Computer will reboot during restart in order to change State of Security Device.

# Device Select

TPM 1.2 restricts support to TPM 1.2 devices, TPM 2.0 restricts support to TPM 2.0 devices, Auto supports both with the default set to TPM 2.0 devices if not found, and TPM 1.2 devices are enumerated.

# A.3 Security

<table><tr><td colspan="2">Aptio Setup Utility - Copyright (C) 2016 American Megatrends, Inc.Main Advanced Security Boot Save &amp; Exit</td></tr><tr><td>Password DescriptionIf ONLY the Administrator&#x27;s password is set,then this only limits access to Setup and isonly asked for when entering Setup.If ONLY the User&#x27;s password is set, then thisis a power on password and must be entered toboot or enter Setup. In Setup the User willhave Administrator rights.The password length must bein the following range:Minimum length 3Maximum length 20Administrator PasswordUser Password</td><td>Set Administrator Password+: Select Screen↑↓: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF2: Previous ValuesF3: Optimized DefaultsF4: Save &amp; ExitESC: Exit</td></tr></table>

If only the Administrator's password is set, access to Setup is limited and the password requested when entering. If only the user's password is set, power on requires authentication to boot or enter Setup. In Setup the user has Administrator rights.

# Administrator Password

Sets Administrator Password.

# User Password

Sets User Password.

# A.4 Boot

<table><tr><td colspan="2">Aptio Setup Utility - Copyright (C) 2016 American Megatrends, Inc.</td></tr><tr><td colspan="2">Main Advanced Security Boot Save &amp; Exit</td></tr><tr><td>Boot Configuration
Setup Prompt Timeout 1
Bootup NumLock State [On]
Quiet Boot [Enabled]</td><td rowspan="4">Number of seconds to wait for setup activation key.
65535(0xFFFF) means indefinite waiting.</td></tr><tr><td>Boot Option Priorities
Boot Option #1 [P0: 2.5&quot; SATA SSD
3MG2-P ]
Boot Option #2 [UEFI: USB FLASH DRIVE
PMAP, Partition 1]</td></tr><tr><td>Boot Option #3 [UEFI: Built-in EFI
Shell]</td></tr><tr><td>Fast Boot [Disabled]</td></tr><tr><td>New Boot Option Policy [Default]</td><td rowspan="2">+: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save &amp; Exit
ESC: Exit</td></tr><tr><td>▶ CSM Configuration</td></tr><tr><td colspan="2">Version 2.17.1255. Copyright (C) 2016 American Megatrends, Inc.</td></tr></table>

# Setup Prompt Timeout

Number of seconds before setup activation key is launched, with 65535(0xFFFF) generating indefinite waiting.

# Bootup NumLock State

Sets keypad Number Lock status following boot.

# Quiet Boot

When Disabled, directs BIOS to display POST messages, and when Enabled, directs BIOS to display the OEM logo.

# Boot Option Priorities

Specifies the priority of boot devices, all detected during POST and displayed. Select Boot Option # and select the desired device.

# Fast Boot

Enables or disables boot initializing the minimum devices required to launch active boot option. Does not affect BBS boot options.

# New Boot Option Policy

Controls the placement of newly detected UEFI boot options.

# Hard Drive BBS Priorities

Sets the order of legacy devices in this group.

# A.4.1 CSM Configuration

<table><tr><td colspan="2">Aptio Setup Utility - Copyright (C) 2016 American Megatrends, Inc.</td></tr><tr><td colspan="2">Boot</td></tr><tr><td>Compatibility Support Module Configuration</td><td>Enable/Disable CSM Support.</td></tr><tr><td>CSM Support [Enabled]</td><td></td></tr><tr><td>CSM16 Module Version 07.79</td><td></td></tr><tr><td>GateA20 Active [Upon Request]</td><td></td></tr><tr><td>Option ROM Messages [Force BIOS]</td><td></td></tr><tr><td>INT19 Trap Response [Immediate]</td><td></td></tr><tr><td>Boot option filter [UEFI and Legacy]</td><td></td></tr><tr><td>Option ROM execution</td><td></td></tr><tr><td>Network [Do not launch]</td><td rowspan="4">+: Select Screen↑↓: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF2: Previous ValuesF3: Optimized DefaultsF4: Save &amp; ExitESC: Exit</td></tr><tr><td>Storage [Legacy]</td></tr><tr><td>Video [Legacy]</td></tr><tr><td>Other PCI devices [Legacy]</td></tr></table>

# CSM Support

Enables/disables CSM Support.

# GateA20 Active

UPON REQUEST disables GA20 using BIOS services, and ALWAYS prevents GA20 from being disabled, indicated when any RT code exceeding 1MB is executed.

# Option ROM Messages

Sets display mode for Option ROM.

# INT19 Trap Response

BIOS reaction on INT19 trapping by Option ROM, with IMMEDIATE executing trap immediately, and POSTPONED executing trap during legacy boot.

# Boot option filter

Controls Legacy/UEFI ROM priority.

# Network

Controls execution of UEFI and Legacy PXE OpROM.

# Storage

Controls execution of UEFI and Legacy Storage OpROM.

# Video

Controls execution of UEFI and Legacy Video OpROM.

# Other PCI devices

Determines OpROM execution policy for devices other than Network, Storage, and Video.

# A.5 Save & Exit

<table><tr><td colspan="2">Aptio Setup Utility - Copyright (C) 2016 American Megatrends, Inc.Main Advanced Security Boot Save &amp; Exit</td></tr><tr><td>Save OptionsSave Changes and ExitDiscard Changes and ExitSave Changes and ResetDiscard Changes and ResetSave ChangesDiscard ChangesDefault OptionsRestore DefaultsSave as User DefaultsRestore User DefaultsBoot OverridePO: 2.5&quot; SATA SSD 3MG2-PUSB FLASH DRIVE PMAPUEFI: Built-in EFI ShellUEFI: USB FLASH DRIVE PMAP, Partition 1</td><td>Exit system setup after saving the changes.+: Select Screen↑↓: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF2: Previous ValuesF3: Optimized DefaultsF4: Save &amp; ExitESC: Exit</td></tr><tr><td colspan="2">Version 2.17.1255. Copyright (C) 2016 American Megatrends, Inc.</td></tr></table>

# Save Changes and Exit

Exits system setup after saving changes.

# Discard Changes and Exit

Exits system setup without saving any changes.

# Save Changes and Reset

Resets the system after saving the changes.

# Discard Changes and Reset

Resets the system without saving any changes.

# Save Changes

Saves changes made to that point to any Setup options.

# Discard Changes

Discards changes made to that point to any Setup options.

# Restore Defaults

Restores/loads default values for all Setup options.

# Save as User Defaults

Saves changes made to that point as User defaults.

# Restore User Defaults

Restores all Setup options to User defaults.

# Important Safety Instructions

For user safety, please read and follow all instructions, Warnings, Cautions, and Notes marked in this manual and on the associated device before handling/operating the device, to avoid injury or damage.

S'il vous plaît prêter attention stricte à tous les avertissements et mises en garde figurant sur l'appareil, pour éviter des blessures ou des dommages.

▶ Read these safety instructions carefully
- Keep the User’s Manual for future reference
▶ Read the Specifications section of this manual for detailed information on the recommended operating environment
The device can be operated at an ambient temperature of $55^{\circ}$ C (with DC supply) and $50^{\circ}$ C (with adapter supply);
- When installing/mounting or uninstalling/removing device; or when removal of a chassis cover is required for user servicing (See “Getting Started” on page 23.):

▷ Turn off power and unplug any power cords/cables
▷ Reinstall all chassis covers before restoring power

▶ To avoid electrical shock and/or damage to device:

▷ Keep device away from water or liquid sources
▷ Keep device away from high heat or humidity
▷ Keep device properly ventilated (do not block or cover ventilation openings)
▶ Always use recommended voltage and power source settings
▶ Always install and operate device near an easily accessible electrical outlet
▷ Secure the power cord (do not place any object on/over the power cord)
▶ Only install/attach and operate device on stable surfaces and/or recommended mountings

▶ If the device will not be used for long periods of time, turn off and unplug from its power source

▶ Never attempt to repair the device, which should only be serviced by qualified technical personnel using suitable tools
▶ A Lithium-type battery may be provided for uninterrupted backup or emergency power.

![The image displays a yellow triangular warning sign with a thick black border. Inside the triangle is a large black exclamation point. The top edge of the sign is bordered by a black line against a white background.](.eos-1300-50-1z222-2000-200-en/0f023fa63770a373f6746321b94dd7088184193a1ea2435fcfaba61ea4a2a852.jpg)
CAUTION:

Risk of explosion if battery is replaced with one of an incorrect type; please dispose of used batteries appropriately.

Risque d'explosion si la pile est remplacée par une autre de type incorrect. Veuillez jeter les piles usagées de façon appropriée.

▶ The device must be serviced by authorized technicians when:

The power cord or plug is damaged
▷ Liquid has entered the device interior
The device has been exposed to high humidity and/or moisture
The device is not functioning or does not function according to the User's Manual
The device has been dropped and/or damaged and/or shows obvious signs of breakage

▶ Disconnect the power supply cord before loosening the thumbscrews and always fasten the thumbscrews with a screwdriver before starting the system up
It is recommended that the device be installed only in a server room or computer room where access is:

▶ Restricted to qualified service personnel or users familiar with restrictions applied to the location, reasons therefor, and any precautions required

▶ Only afforded by the use of a tool or lock and key, or other means of security, and controlled by the authority responsible for the location

▶ If PoE (Power over Ethernet) is enabled for the device, the system can ONLY be deployed indoors. Unless otherwise noted, the PoE system is NOT designed to withstand the rigors of outdoor use.

![Yellow triangular warning sign with black smoke symbol indicating hot weather](.eos-1300-50-1z222-2000-200-en/6395f519a8db6e506678b6e1a754431b7c4368bc91900c80027f2bbebeefe042.jpg)

# BURN HAZARD

Touching this surface could result in bodily injury. To reduce risk, allow the surface to cool before touching.

# RISQUE DE BRÛLURES

Ne touchez pas cette surface, cela pourrait entraîner des blessures.

Pour éviter tout danger, laissez la surface refroidir avant de la toucher.

This page intentionally left blank.

# Getting Service

Ask an Expert: http://askanexpert.adlinktech.com

# ADLINK Technology, Inc.

Address: 9F, No.166 Jian Yi Road, Zhonghe District

New Taipei City 235, Taiwan

新北市中和區建一路 166 號 9 樓

Tel: +886-2-8226-5877

Fax: +886-2-8226-5717

Email: service@adlinktech.com

# Ampro ADLINK Technology, Inc.

Address: 5215 Hellyer Avenue, #110

San Jose, CA 95138, USA

Tel: +1-408-360-0200

Toll Free: +1-800-966-5200 (USA only)

Fax: +1-408-360-0222

Email: info@adlinktech.com

# ADLINK Technology (China) Co., Ltd.

Address: 上海市浦东新区张江高科技园区芳春路 300 号 (201203)

300 Fang Chun Rd., Zhangjiang Hi-Tech Park

Pudong New Area, Shanghai, 201203 China

Tel: +86-21-5132-8988

Fax: +86-21-5132-3588

Email: market@adlinktech.com

# ADLINK Technology Beijing

Address: 北京市海淀区上地东路 1 号盈创动力大厦 E 座 801 室(100085)

Rm. 801, Power Creative E, No. 1 Shang Di East Rd.

Beijing, 100085 China

Tel: +86-10-5885-8666

Fax: +86-10-5885-8626

Email: market@adlinktech.com

# ADLINK Technology Shenzhen

Address: 深圳市南山区科技园南区高新南七道 数字技术园

A1 栋 2 楼 C 区 (518057)

2F, C Block, Bldg. A1, Cyber-Tech Zone, Gao Xin Ave. Sec. 7

High-Tech Industrial Park S., Shenzhen, 518054 China

Tel: +86-755-2643-4858

Fax: +86-755-2664-6353

Email: market@adlinktech.com

# LiPPERT ADLINK Technology GmbH

Address: Hans-Thoma-Strasse 11

D-68163 Mannheim, Germany

Tel: +49-621-43214-0

Fax: +49-621 43214-30

Email: emea@adlinktech.com

# PENTA ADLINK Technology GmbH

Ulrichsbergerstrasse 17

94469 Deggendorf, Germany

Tel: +49 (0) 991 290 94 – 10

Fax: +49 (0) 991 290 94 - 29

Email: emea@adlinktech.com

# ADLINK Technology, Inc. (French Liaison Office)

Address: 6 allée de Londres, Immeuble Ceylan
91940 Les Ulis, France

Tel: +33 (0) 1 60 12 35 66

Fax: +33 (0) 1 60 12 35 66

Email: france@adlinktech.com

# ADLINK Technology Japan Corporation

Address: 〒101-0045 東京都千代田区神田鍛冶町 3-7-4
神田 374 ビル 4F
KANDA374 Bldg. 4F, 3-7-4 Kanda Kajicho,
Chiyoda-ku, Tokyo 101-0045, Japan

Tel: +81-3-4455-3722

Fax: +81-3-5209-6013

Email: japan@adlinktech.com

# ADLINK Technology, Inc. (Korean Liaison Office)

Address: 경기도 성남시 분당구 수내로 46 번길 4 경동빌딩 2 층 (수내동 4-4 번지) (우) 463-825
2F, Kyungdong B/D, 4 Sunae-ro 46 beon-gil
Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-825

Toll Free +82-80-800-0585

Tel +82-31-786-0585

Fax +82-31-786-0583

Email: korea@adlinktech.com

# ADLINK Technology Singapore Pte. Ltd.

Address: 84 Genting Lane #07-02A, Cityneon Design Centre Singapore 349584

Tel: +65-6844-2261

Fax: +65-6844-2263

Email: singapore@adlinktech.com

# ADLINK Technology Singapore Pte. Ltd. (Indian Liaison Office)

Address: #50-56, First Floor, Spearhead Towers Margosa Main Road (between 16th/17th Cross) Malleswaram, Bangalore - 560 055, India

Tel: +91-80-65605817, +91-80-42246107

Fax: +91-80-23464606

Email: india@adlinktech.com

# ADLINK Technology, Inc. (Israeli Liaison Office)

Address: 27 Maskit St., Corex Building
PO Box 12777
Herzliya 4673300, Israel

Tel: +972-54-632-5251

Fax: +972-77-208-0230

Email: israel@adlinktech.com

# ADLINK Technology, Inc. (UK Liaison Office)

Tel: +44 774 010 59 65

Email: UK@adlinktech.com
[🔗 Link to the original document](.eos-1300-50-1z222-2000-200-en/eos-1300-50-1z222-2000-200-en.pdf)