NuDAM-6050 NuDAM-6052

NuDAM-6053 NuDAM-6054

NuDAM-6056 NuDAM-6058

NuDAM-6060 NuDAM-6063

# Digital I/O Modules

© Copyright 1995\~2001 ADLINK Technology Inc.

All Rights Reserved.

Manual Rev. 3.51: March 27, 2001

Part No : 50-12003-201

The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer.

In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.

This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer.

# Trademarks

ND-6050, ND-6052, ND-6053, ND-6054, ND-6056, ND6058, ND-6060 and ND-6063 are registered trademarks of ADLink Technology Inc., IBM PC is a registered trademark of International Business Machines Corporation. Intel is a registered trademark of Intel Corporation. Other product names mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks of their respective companies.

# Getting service from ADLINK

♦Customer Satisfaction is always the most important thing for ADLINK Tech Inc. If you need any help or service, please contact us and get it.

<table><tr><td colspan="4">ADLINK Technology Inc.</td></tr><tr><td>Web Site</td><td colspan="3">http://www.adlink.com.twhttp://www.adlinktechnology.com</td></tr><tr><td>Sales &amp; Service</td><td colspan="3">service@Adlink.com.tw</td></tr><tr><td rowspan="5">Technical Support</td><td>NuDAQ</td><td colspan="2">nudaq@adlink.com.tw</td></tr><tr><td>NuDAM</td><td colspan="2">nudam@adlink.com.tw</td></tr><tr><td>NuIPC</td><td colspan="2">nuipc@adlink.com.tw</td></tr><tr><td>NuPRO</td><td colspan="2">nupro@adlink.com.tw</td></tr><tr><td>Software</td><td colspan="2">sw@adlink.com.tw</td></tr><tr><td>TEL</td><td>+886-2-82265877</td><td>FAX</td><td>+886-2-82265717</td></tr><tr><td>Address</td><td colspan="3">9F, No. 166, Jian Yi Road, Chungho City, Taipei, 235 Taiwan, R.O.C.</td></tr></table>

♦Please inform or FAX us of your detailed information for a prompt, satisfactory and constant service.

<table><tr><td colspan="4">Detailed Company Information</td></tr><tr><td>Company/Organization</td><td colspan="3"></td></tr><tr><td>Contact Person</td><td colspan="3"></td></tr><tr><td>E-mail Address</td><td colspan="3"></td></tr><tr><td>Address</td><td colspan="3"></td></tr><tr><td>Country</td><td colspan="3"></td></tr><tr><td>TEL</td><td></td><td>FAX</td><td></td></tr><tr><td>Web Site</td><td colspan="3"></td></tr><tr><td colspan="4">Questions</td></tr><tr><td>Product Model</td><td colspan="3"></td></tr><tr><td>Environment to Use</td><td colspan="3">☐OS: ____☐Computer Brand: ____☐M/B: ☐CPU:☐Chipset: ☐BIOS:☐Video Card:☐Network Interface Card:☐Other:</td></tr><tr><td>Challenge Description</td><td colspan="3"></td></tr><tr><td>Suggestions for ADLINK</td><td colspan="3"></td></tr></table>

# Table of Contents

# Chapter 1 Introduction .........

1.1 About the NuDAM DIO Modules ...
1.2 Overview of NuDAM-6050 . . 2

1.2.1 What is NuDAM-6050? . 2
1.2.2 Features of NuDAM-6050 .. 2
1.2.3 Specifications of NuDAM-6050 .. 2
1.2.4 A Look at ND-6050 & Pin Assignment .. 4
1.2.5 Pin Definitions of NuDAM-6050 .5
1.2.6 ND-6050 Functional Block Diagram.. .6

1.3 Overview of NuDAM-6052 ..

1.3.1 What is NuDAM-6052 ? .
1.3.2 Features of NuDAM-6052 ..
1.3.3 Specifications of NuDAM-6052 .
1.3.4 A Look at ND-6052 & Pin Assignment . 9
1.3.5 Pin Definitions of NuDAM-6052 ..10
1.3.6 ND-6052 Functional Block Diagram.. .11

1.4 Overview of NuDAM-6053 . 12

1.4.1 What is NuDAM-6053 ? . .. 12
1.4.2 Features of NuDAM-6053 . . 12
1.4.3 Specifications of NuDAM-6053 . .12
1.4.4 A Look at ND-6053 & Pin Assignment . .14
1.4.5 Pin Definitions of NuDAM-6053 .. 15
1.4.6 ND-6053 Functional Block Diagram.. ..16

1.5 Overview of NuDAM-6054 . . 17

1.5.1 What is NuDAM-6054 ? . 17
1.5.2 Features of NuDAM-6054 .. .17
1.5.3 Specifications of NuDAM-6054 . .17
1.5.4 A Look at ND-6054 & Pin Assignment .. ..19
1.5.5 Pin Definitions of NuDAM-6054 . .20
1.5.6 ND-6054 Functional Block Diagram.. .21

1.6 Overview of NuDAM-6056 . .. 22

1.6.1 What is NuDAM-6056 ? . .22
1.6.2 Features of NuDAM-6056 .. . 22
1.6.3 Specifications of NuDAM-6056 .. . 22
1.6.4 A Look at ND-6056 & Pin Assignment . .24
1.6.5 Pin Definitions of NuDAM-6056 .24
1.6.5 Pin Definitions of NuDAM-6056 . 25
1.6.6 ND-6056 Functional Block Diagram.. ..26

1.7 Overview of NuDAM-6058 . ... 27

1.7.1 What is NuDAM-6058 ? . ..27
1.7.2 Features of NuDAM-6058 . .27

1.7.3 Specifications of NuDAM-6058 . ..28
1.7.4 A Look at ND-6058 & Pin Assignment . ..30
1.7.5 Pin Definitions of NuDAM-6058.. .31
1.7.6 ND-6058 Functional Block Diagram .. .32

# 1.8 Overview of NuDAM-6060 . 33

1.8.1 What is NuDAM-6060 ? . ..33
1.8.2 Features of NuDAM-6060 . .33
1.8.3 Specifications of NuDAM-6060 .33
1.8.4 Using Relay Output.. .35
1.8.5 A Look at ND-6060 & Pin Assignment . ..36
1.8.6 Pin Definitions of NuDAM-6060.. .37
1.8.7 ND-6060 Functional Block Diagram .. .38

# 1.9 Overview of NuDAM-6063 .. 39

1.9.1 What is NuDAM-6063 ? . ..39
1.9.2 Features of NuDAM-6063 . .39
1.9.3 Specifications of NuDAM-6063 .39
1.9.4 Using Relay Output.. ..40
1.9.5 A Look at ND-6063 & Pin Assignment . ..41
1.9.6 Pin Definitions of NuDAM-6063.. ..42
1.9.7 ND-6063 Functional Block Diagram .. ..43

# Chapter 2 Initialization & Installation .............. . 44

2.1 Software Installation ... .. 44
2.2 Initializing a Brand-New Module.. .. 45

2.2.1 Objective of Initializing a Brand-New NuDAM .. ...45
2.2.2 Default State . ..46
2.2.3 Initialization Equipments.. ..47
2.2.4 Initialization Procedure .. .47
2.2.5 Initialization Wiring . ..48

2.3 Install a New NuDAM to a Existing Network .. ... 49

2.3.1 Equipments for Install a New Module.. ..49
2.3.2 Installing Procedures... ..49

2.4 Application Wiring for NuDAM-6050 . .. 50
2.5 Application Wiring for NuDAM-6052 . ... 51
2.6 Application Wiring for NuDAM-6053 . .. 52
2.7 Application Wiring for NuDAM-6054 . .. 53
2.8 Application Wiring for NuDAM-6056 . .. 53
2.9 Application Wiring for NuDAM-6058 . .. 54
2.10 Application Wiring for NuDAM-6060 . .. 55
2.11 Application Wiring for NuDAM-6063 . .. 56

# Chapter 3 Command Set ........ . 57

3.1 Command and Response . .. 57

3.1.1 Introduction .. .57
3.1.2 Document Conventions.. .58
3.1.3 Format of NuDAM Commands . 58
3.1.4 Response of NuDAM Commands . .59

3.2 Summary of Command Set.. .. 60
3.3 Set Configuration... ... 62
3.4 Read Configuration .. ... 64
3.5 Read Module Name .. ... 66
3.6 Read Firmware Version . ... 67
3.7 Reset Status... .. 68
3.8 Digital Output... ... 69
3.9 Digital Output (Continued)... .. 71
3.10 Digital Output (Continued).. .. 73
3.11 Digital Output (Continued)... .. 75
3.12 Synchronized Sampling . .. 77
3.13 Read Synchronized Data . .. 78
3.14 Digital Input .. ... 81
3.14 Programmable I/O Mode Setting.. ... 84
3.15 Read Leading Code Setting.. .. 86
3.16 Change Leading Code Setting.. .. 88
3.17 Set Host Watchdog Timer & Safety Value ... ... 90
3.18 Read Host Watchdog Timer & Safety Value... .. 93
3.19 Change Polarity. .. 95
3.20 Read Polarity.. .. 96
3.21 Host is OK .. .. 97

# Product Warranty/Service ......... .... 98

![1](.nd-6058-manual-2/b93552f215fd287aac58e3fb60a67b870888172ea9ac8fa6791af9500cb6eede.jpg)

# Introduction

# 1.1 About the NuDAM DIO Modules

The NuDAM provides a series of digital input or output (DIO) modules to sense the digital signal or to control the remote devices.

The specified features of each module are shown here.

• NuDAM-6050 : Digital I/O module
• NuDAM-6052 : Isolated digital input module
• NuDAM-6053 : 16-channel digital input module
• NuDAM-6054 : 15-channel isolated digital input module
• NuDAM-6056 : 15-channel isolated digital output module
• NuDAM-6058 : 28 programmable digital I/O module
• NuDAM-6060 : relay output and isolated digital input module
• NuDAM-6063 : 8-channel relay output module

# 1.2 Overview of NuDAM-6050

# 1.2.1 What is NuDAM-6050?

NuDAM-6050 is a digital input and output module. The digital input channels can monitor active TTL signals, and sense passive switch on/off signal because of the internal pull high resistors. The convenient open collector output channels can sink up to 50 mA current. Combining with the relay devices, it is possible to control the high power devices by programming output channel of the NuDAM-6050.

# 1.2.2 Features of NuDAM-6050

♦ 7 bits digital input
♦ 8 bits open collector digital output
Programmable host watchdog timer for host failure protection
♦ Internal watchdog timer for device failure protection
♦ Easy programming by software
Easy installation and wiring

# 1.2.3 Specifications of NuDAM-6050

♦ Interface
• Interface : RS-485, 2 wires
• Speed (bps) : 1200, 2400, 4800, 9600, 19.2K, 38.4K, 115.2K (115.2K only for firmware reversion above A4.00)

Digital Input

• Channel numbers : 7
• Logical level 0 : +1V maximum
• Logical level 1: +3.5V\~30V
• Pull up resister : 10KΩ
• Maximum current : 0.5mA

# ♦ Digital Output

• Channel numbers : 8
• Output characteristic : open collector transistor
• Maximum current sink : 50mA
• Max. power dissipation : 300mW

# Watchdog Function

• Module internal watchdog timer: 150 ms
• Power failure threshold : 4.65 V
• Safety value : 8 output channels
• Host programmable watchdog :
• 100 ms \~ 25.500 sec

# ♦ Power

• Power supply : +10V to +30V
• Current consumption : 0.5 W

# 1.2.4 A Look at ND-6050 & Pin Assignment

![20 DI 6 DI 5 DI 4 DI 3 DI 2 DI 1 DI 0 DO 0 DO 1 DO 2\n11\nND-6050 Digital\nInput/Output\nI/O Type Signal\nDigital Output Bit 0-7\nDigital Input Bit 0-6\n1\nDO 7 DO 6 DO 5 DO 4 DO 3 DEFAULT Y)DATA+\n(G)DATA-\n(R)+Vs (B)GND\n10](.nd-6058-manual-2/de015b40c2dc3c9c6bd3bb5765b8d69f6b4bb8fa7800ac1cc0f094775efef7e7.jpg)

# 1.2.5 Pin Definitions of NuDAM-6050

<table><tr><td>Pin #</td><td>Signal Name</td><td>Description</td></tr><tr><td>1</td><td>DO 7</td><td>Digital output channel 7</td></tr><tr><td>2</td><td>DO 6</td><td>Digital output channel 6</td></tr><tr><td>3</td><td>DO 5</td><td>Digital output channel 5</td></tr><tr><td>4</td><td>DO 4</td><td>Digital output channel 4</td></tr><tr><td>5</td><td>DO 3</td><td>Digital output channel 3</td></tr><tr><td>6</td><td>Default*</td><td>Initial state setting</td></tr><tr><td>7</td><td>(Y) DATA+</td><td>RS-485 series signal, positive</td></tr><tr><td>8</td><td>(G) DATA-</td><td>RS-485 series signal, negative</td></tr><tr><td>9</td><td>(R) +Vs</td><td>Power supply, +10V~+30V</td></tr><tr><td>10</td><td>(B) GND</td><td>Ground</td></tr><tr><td>11</td><td>DO 2</td><td>Digital output channel 2</td></tr><tr><td>12</td><td>DO 1</td><td>Digital output channel 1</td></tr><tr><td>13</td><td>DO 0</td><td>Digital output channel 0</td></tr><tr><td>14</td><td>DI 0</td><td>Digital input channel 0</td></tr><tr><td>15</td><td>DI 1</td><td>Digital input channel 1</td></tr><tr><td>16</td><td>DI 2</td><td>Digital input channel 2</td></tr><tr><td>17</td><td>DI 3</td><td>Digital input channel 3</td></tr><tr><td>18</td><td>DI 4</td><td>Digital input channel 4</td></tr><tr><td>19</td><td>DI 5</td><td>Digital input channel 5</td></tr><tr><td>20</td><td>DI 6</td><td>Digital input channel 6</td></tr></table>

# 1.2.6 ND-6050 Functional Block Diagram

![This block diagram illustrates a system centered around a **Micro Processor** connected to various peripheral and input/output blocks.\n\n**Blocks and Power Section:**\n*   **Power Input +10V ~ +30V** connects via arrows to the **Power Regulator & Filter**.\n*   The **Power Regulator & Filter** outputs arrows pointing upward to **+ 5V** and to the right to **GND**.\n\n**Micro Processor Connections:**\nThe **Micro Processor** block serves as the central hub, maintaining bidirectional (double-headed arrow) connections with the following blocks:\n*   **Watchdog/Power Failure Supervisor**\n*   **RS-485 Rec/Drv**\n*   **EEPROM Config Data Safe Value**\n*   **8-bit Digital/Output**\n*   **7-bit Digital/Input**\n*   **1-bit Digital/Input**\n\n**Peripheral and I/O Connections:**\n*   **RS-485 Rec/Drv:** Has arrows pointing left to external labels **Data +** and **Data -**.\n*   **8-bit Digital/Output:** Has arrows pointing right to external labels **DO0** and **DO7**.\n*   **7-bit Digital/Input:** Has arrows pointing left from external labels **DI0** and **DI6**.\n*   **1-bit Digital/Input:** Has an arrow pointing left from the external label **Default* Pin**.](.nd-6058-manual-2/23de77bd19885b9cd02cdc66af34736ffabbadc0f0c31584515d3753c31f9ae3.jpg)

# 1.3 Overview of NuDAM-6052

# 1.3.1 What is NuDAM-6052 ?

NuDAM-6052 provides 8 isolated digital input channels. Six of the input channels are differential type and two of them are single-ended with common ground. The isolation voltage is up to 5000 Vrms. It is suitable to use NuDAM-6052 in industrial environment with the dangerous of high voltage electric shock.

# 1.3.2 Features of NuDAM-6052

A 8 bits isolated input
♦ 5000 Vrms isolation voltage
♦ Programmable host watchdog timer for host failure protection
♦ Internal watchdog timer for device failure protection
Easy programming by software
♦ Easy installation and wiring

# 1.3.3 Specifications of NuDAM-6052

♦ Interface
• Interface : RS-485, 2 wires
• Speed (bps) : 1200, 2400, 4800, 9600, 19.2K, 38.4K, 115.2K (115.2K only for firmware reversion above A4.00)
♦ Input
• Channel numbers : 6 differential channels, 2 single ended
• Logical level 0 : +1V Max.
• Logical level 1: +3.5V \~ +24V
♦ Watchdog Function
• Module internal watchdog timer : 150ms
• Power failure threshold : 4.65 V

• Safe value : 8 output channels
• Host programmable watchdog :100 ms \~ 25.5 sec

# ♦ Power

• Power supply : +10V to +30V
• Current consumption : 0.4 W

# 1.3.4 A Look at ND-6052 & Pin Assignment

![20\nDI 4-\nDI 4+\nDI 3-\nDI 3+\nDI 2-\nDI 2+\nDI 1-\nDI 1+\nDI 0-\nDI 0+\nDI 11\nND-6052\nIsolated\nDigital Input\nInput Type	Channels\nDiffential	6\nSingle Ended	2\n1\nDI 5+\nDI 5-\nDI 6+\nD.GND	DI 7+\nDEFAULT	Y)DATA+\n(G)DATA-\n(B)+Vs\n(B)GND\n10](.nd-6058-manual-2/1271e62fabe0710e34eeb75eb4d4c3637dfc872012740085fb0ac9f67aee95d9.jpg)

# 1.3.5 Pin Definitions of NuDAM-6052

<table><tr><td>Pin #</td><td>Signal Name</td><td>Description</td></tr><tr><td>1</td><td>DI5+</td><td>Digital Input Channel 5+</td></tr><tr><td>2</td><td>DI5 -</td><td>Digital Input Channel 5 -</td></tr><tr><td>3</td><td>DI6+</td><td>Digital Input Channel 6+</td></tr><tr><td>4</td><td>D.GND</td><td>Digital Input Ground</td></tr><tr><td>5</td><td>DI7+</td><td>Digital Input Channel 7+</td></tr><tr><td>6</td><td>Default*</td><td>Initial state setting</td></tr><tr><td>7</td><td>(Y) DATA+</td><td>RS-485 series signal, positive</td></tr><tr><td>8</td><td>(G) DATA-</td><td>RS-485 series signal, negative</td></tr><tr><td>9</td><td>(R) +VS</td><td>Power supply, +10V~+30V</td></tr><tr><td>10</td><td>(B) GND</td><td>Ground</td></tr><tr><td>11</td><td>DI0+</td><td>Digital Input Channel 0+</td></tr><tr><td>12</td><td>DI0 -</td><td>Digital Input Channel 0 -</td></tr><tr><td>13</td><td>DI1+</td><td>Digital Input Channel 1+</td></tr><tr><td>14</td><td>DI1 -</td><td>Digital Input Channel 1 -</td></tr><tr><td>15</td><td>DI2+</td><td>Digital Input Channel 2+</td></tr><tr><td>16</td><td>DI2 -</td><td>Digital Input Channel 2 -</td></tr><tr><td>17</td><td>DI3+</td><td>Digital Input Channel 3+</td></tr><tr><td>18</td><td>DI3 -</td><td>Digital Input Channel 3 -</td></tr><tr><td>19</td><td>DI4+</td><td>Digital Input Channel 4+</td></tr><tr><td>20</td><td>DI4 -</td><td>Digital Input Channel 4 -</td></tr></table>

# 1.3.6 ND-6052 Functional Block Diagram

![Based on the provided block diagram, here is an accurate and concise description of the labeled blocks and their connections:\n\n**Power Section**\n*   **Block:** 'Power Regulator & Filter'\n*   **Input:** Receives 'Power Input +10V ~ +30V'.\n*   **Outputs:** Outputs '+5V' and 'GND'.\n\n**Central Processing & Control**\n*   **Block:** 'Micro Processor' (Central hub)\n    *   **Connection:** Bidirectional connection to 'RS-485 Rec/Drv'.\n    *   **Connection:** Bidirectional connection to the circuitry above (consisting of a resistor, capacitor, transistor, and diode).\n    *   **Connection:** Receives input from 'EEPROM Config Data Safe Value'.\n    *   **Connection:** Outputs connect to four dotted rectangular blocks on the right.\n*   **Block:** 'RS-485 Rec/Drv'\n    *   **Connection:** Outputs 'Data -'.\n*   **Block:** 'EEPROM Config Data Safe Value'\n    *   **Connection:** Outputs to 'Micro Processor'.\n*   **Block:** 'Watchdog/Power Failure Supervisor'\n    *   **Note:** This block is located to the left of the central circuitry. While it likely describes the adjacent circuit (the one with the resistor labeled '+5V'), there are no explicit lines connecting this specific text box to other blocks.\n\n**Digital Inputs (Right Side)**\nThe 'Micro Processor' connects to four dotted rectangular blocks representing input interfaces:\n1.  Top block: Connects to 'DI0+' and 'DI0-'. (A dotted line connects this block to the one below it).\n2.  Middle block: Connects to 'DI5+' and 'DI5-'.\n3.  Lower block: Connects to 'DI6+' and 'D.GND'.\n4.  Bottom block: Connects to 'DI7+' and 'D.GND'.](.nd-6058-manual-2/d5fc1234a0702ba92d9caa456aaa55006cefcba14ba6b9a779d5931d2dad575c.jpg)

# 1.4 Overview of NuDAM-6053

# 1.4.1 What is NuDAM-6053 ?

NuDAM-6053 provides 16 digital input channels for dry contact or wet contact signals. The effective distance from DI to contact point is up to 500m for dry contact input.

# 1.4.2 Features of NuDAM-6053

• 16 bits digital input
• Programmable host watchdog timer for host failure protection
• Internal watchdog timer for device failure protection
• Easy programming by software
• Easy installation and wiring

# 1.4.3 Specifications of NuDAM-6053

♦ Interface
• Interface : RS-485, 2 wires
Speed (bps) : 1200, 2400, 4800, 9600, 19.2K, 38.4K, 115.2K (115.2K only for firmware reversion above A4.00)

♦ Input

• Channel numbers : 16
• Dry Contact:
• Logical level 0 : close to GND
• Logical level 1 : open
• Wet Contact :
• Logical level 0 : +2V max.
• Logical level 1 : +4V \~ + 30V

Watchdog Function

• Module internal watchdog timer : 150ms

• Power failure threshold : 4.65 V
• Host programmable watchdog : 100 ms \~ 25.5 sec
• Power supply : +10V to +30V
• Current consumption : 0.4 W

# ♦ Power

# 1.4.4 A Look at ND-6053 & Pin Assignment

![20\nDI 9\nDI 8\nDI 7\nDI 6\nDI 5\nDI 4\nDI 3\nDI 2\nDI 1\nDI 0\n16-CH\nND-6053 Digital\nInput Type Channels\nDigital Input 16\n1\nDI 10 DI 11 DI 12 DI 13 DI 14 DEFAULT (Y)DATA+\n(G)DATA-\n(R)+Vs (B)GND 10](.nd-6058-manual-2/6826db3347102c3a80c79893b7fa8cbfe46ebbb8debb66155c54cfeecbd86631.jpg)

# 1.4.5 Pin Definitions of NuDAM-6053

<table><tr><td>Pin #</td><td>Signal Name</td><td>Description</td></tr><tr><td>1</td><td>DI10</td><td>Digital Input Channel 10</td></tr><tr><td>2</td><td>DI11</td><td>Digital Input Channel 11</td></tr><tr><td>3</td><td>DI12</td><td>Digital Input Channel 12</td></tr><tr><td>4</td><td>DI13</td><td>Digital Input Channel 13</td></tr><tr><td>5</td><td>DI14</td><td>Digital Input Channel 14</td></tr><tr><td>6</td><td>Default*/DI15</td><td>Initial state setting/ Digital Input Channel 15</td></tr><tr><td>7</td><td>(Y) DATA+</td><td>RS-485 series signal, positive</td></tr><tr><td>8</td><td>(G) DATA-</td><td>RS-485 series signal, negative</td></tr><tr><td>9</td><td>(R) +VS</td><td>Power supply, +10V~+30V</td></tr><tr><td>10</td><td>(B) GND</td><td>Ground</td></tr><tr><td>11</td><td>DI0</td><td>Digital Input Channel 0</td></tr><tr><td>12</td><td>DI1</td><td>Digital Input Channel 1</td></tr><tr><td>13</td><td>DI2</td><td>Digital Input Channel 2</td></tr><tr><td>14</td><td>DI3</td><td>Digital Input Channel 3</td></tr><tr><td>15</td><td>DI4</td><td>Digital Input Channel 4</td></tr><tr><td>16</td><td>DI5</td><td>Digital Input Channel 5</td></tr><tr><td>17</td><td>DI6</td><td>Digital Input Channel 6</td></tr><tr><td>18</td><td>DI7</td><td>Digital Input Channel 7</td></tr><tr><td>19</td><td>DI8</td><td>Digital Input Channel 8</td></tr><tr><td>20</td><td>DI9</td><td>Digital Input Channel 9</td></tr></table>

# 1.4.6 ND-6053 Functional Block Diagram

\+ 5V

![Based on the provided block diagram, here are the labeled blocks and their connections:\n\n**Blocks:**\n*   Power Input +10V ~ +30V\n*   Power Regulator & Filter\n*   Watchdog/Power Failure Supervisor\n*   RS-485 Rec/Drv\n*   Micro Processor\n*   EEPROM Config Data Safe Value\n*   15-bit Digital/Input\n*   1-bit Digital/Input\n\n**Connections:**\n*   **Power Input +10V ~ +30V** connects via two arrows into **Power Regulator & Filter**.\n*   **Power Regulator & Filter** has two outputs to the right: an upper output arrow and a lower line labeled **GND**.\n*   **Watchdog/Power Failure Supervisor** is connected via a vertical double-headed arrow to **Micro Processor**.\n*   **RS-485 Rec/Drv** is connected via a horizontal double-headed arrow to **Micro Processor**. It has two outputs to the left labeled **Data +** and **Data -**.\n*   **EEPROM Config Data Safe Value** connects via an arrow to **Micro Processor**.\n*   **Micro Processor** connects via a horizontal double-headed arrow to **15-bit Digital/Input**.\n*   **15-bit Digital/Input** receives inputs labeled **DI0** and **DI14**.\n*   **Micro Processor** connects via an arrow to **1-bit Digital/Input**.\n*   **1-bit Digital/Input** receives an input labeled **Default* Pin/DI15**.](.nd-6058-manual-2/8760e87ccf7a60c9eaf959b48cb30254a843f72dfb19887628c3c497bcd20ed1.jpg)

# 1.5 Overview of NuDAM-6054

# 1.5.1 What is NuDAM-6054 ?

NuDAM-6054 provides 15 isolated digital input channels. All of the input channels are common power type and one of them is using the same pin with default (use jumper to choose). The isolation voltage is up to 5000 Vrms. It is suitable to use NuDAM-6054 in industrial environment with the dangerous of high voltage electric shock.

# 1.5.2 Features of NuDAM-6054

• 15 bits digital inputs with isolation protection and common power
• 5000 Vrms isolation voltage
• Programmable host watchdog timer for host failure protection
• Internal watchdog timer for device failure protection
• Easy programming by software
• Easy installation and wiring

# 1.5.3 Specifications of NuDAM-6054

♦ Interface
• Interface : RS-485, 2 wires
• Speed (bps) : 1200, 2400, 4800, 9600, 19.2K, 38.4K, 115.2K (115.2K only for firmware reversion above A4.00)
♦ Input
Channel numbers : 15 isolation common power input channels (the fifteenth channel is the same with default pin, but can use jumper to choose)
• Input type : source type
• Effective distance: 500 m
• Common external voltage: 24V
♦ Watchdog Function

• Module internal watchdog timer : 150msec
• Power failure threshold : 4.65 V
• Host programmable watchdog :100 ms \~ 25.5 sec

# ♦ Power

• Power supply : +10V to +30V
• Power consumption : 0.4 W

# 1.5.4 A Look at ND-6054 & Pin Assignment

![20\nDI0 DI1 DI2 DI3 DI4 DI5 DI6 DI7 DI8 DI9\n11\nND-6054\n15-CH Isolated\nDigital Input\nInput Type Channels\nDI 15\nDI10 DI11 DI12 DI13\nEx24V DEFAULT *\nDI14 Y)DATA+\n(G)DATA-\n(B)+Vs (B)GND 10](.nd-6058-manual-2/b1cb21446e9d0f28c58abe13a8afbb13857db09e34cc6d437ff474c2117b16e3.jpg)

# 1.5.5 Pin Definitions of NuDAM-6054

<table><tr><td>Pin #</td><td>Signal Name</td><td>Description</td></tr><tr><td>1</td><td>DI10</td><td>Digital input channel 10</td></tr><tr><td>2</td><td>DI11</td><td>Digital input channel 11</td></tr><tr><td>3</td><td>DI12</td><td>Digital input channel 12</td></tr><tr><td>4</td><td>DI13</td><td>Digital input channel 13</td></tr><tr><td>5</td><td>Ext24V</td><td>External common +24V</td></tr><tr><td>6</td><td>Default*/DI14</td><td>Initial state setting or digital input channel 14</td></tr><tr><td>7</td><td>(Y) DATA+</td><td>RS-485 series signal, positive</td></tr><tr><td>8</td><td>(G) DATA-</td><td>RS-485 series signal, negative</td></tr><tr><td>9</td><td>(R) +VS</td><td>Power supply, +10V~+30V</td></tr><tr><td>10</td><td>(B) GND</td><td>Ground</td></tr><tr><td>11</td><td>DI9</td><td>Digital input channel 9</td></tr><tr><td>12</td><td>DI8</td><td>Digital input channel 8</td></tr><tr><td>13</td><td>DI7</td><td>Digital input channel 7</td></tr><tr><td>14</td><td>DI6</td><td>Digital input channel 6</td></tr><tr><td>15</td><td>DI5</td><td>Digital input channel 5</td></tr><tr><td>16</td><td>DI4</td><td>Digital input channel 4</td></tr><tr><td>17</td><td>DI3</td><td>Digital input channel 3</td></tr><tr><td>18</td><td>DI2</td><td>Digital input channel 2</td></tr><tr><td>19</td><td>DI1</td><td>Digital input channel 1</td></tr><tr><td>20</td><td>DI0</td><td>Digital input channel 0</td></tr></table>

# 1.5.6 ND-6054 Functional Block Diagram

![The diagram illustrates a system architecture centered around a **Micro Processor**.\n\n**Power Section:**\n*   A block labeled **'Power Input +10V ~ +30V'** feeds into a **'Power Regulator & Filter'** block.\n*   The regulator outputs a **'+5V'** rail (indicated by an upward arrow) and a **'GND'** rail.\n*   The **'+5V'** rail provides power to the rest of the circuit.\n\n**Micro Processor Connections:**\n*   The **Micro Processor** is connected bidirectionally to a **'Watchdog/Power Failure Supervisor'** block.\n*   It is connected bidirectionally to an **'RS-485 Rec/Drv'** block. This block outputs **'Data +'** and **'Data -'** to the left.\n*   It is connected bidirectionally to an **'EEPROM Config Data Safe Value'** block.\n*   It receives **'+5V'** power (via a resistor symbol).\n\n**Digital Inputs (Right Side):**\n*   The Micro Processor connects to several input blocks (depicted as dotted rectangles):\n    *   A block with inputs **'+24V'** and **'DI1'**.\n    *   Three blocks below it with inputs **'+24V'** and digital inputs **'DI12'**, **'DI13'**, and **'DI14'**.\n*   There is a separate circuit block (dotted box) containing an optocoupler and filter components. It is fed by **'+5V'** via a resistor and outputs a signal labeled **'DI0'**. A **'+24V'** label is near the output side of this circuit.](.nd-6058-manual-2/0f56f6a880686751bef76d79e8a7cae78cc40ac1faba3773356f0ccea12eff37.jpg)

# 1.6 Overview of NuDAM-6056

# 1.6.1 What is NuDAM-6056 ?

NuDAM-6056 provides 15 isolated digital output channels. All of the output channels are common ground type and one of them is use the same pin with default (use jumper to choose). The isolation voltage is up to 5000 Vrms. It is suitable to use NuDAM-6056 in industrial environment with the dangerous of high voltage electric shock.

# 1.6.2 Features of NuDAM-6056

♦ 15 bits digital open collector output with isolation protection and common ground
♦ 5000 Vrms isolation voltage
Programmable host watchdog timer for host failure protection
♦ Internal watchdog timer for device failure protection
♦ Easy programming by software
♦ Easy installation and wiring

# 1.6.3 Specifications of NuDAM-6056

# ♦ Interface

• Interface : RS-485, 2 wires
Speed (bps) : 1200, 2400, 4800, 9600, 19.2K, 38.4K, 115.2K (115.2K only for firmware reversion above A4.00)

# Digital Output

Channel numbers : 15 isolation common ground output channels(the fifteenth channel is the same with default pin,but could use jumper to choose).
• Output characteristic:open collector transistor
• Maximum current sink:50mA(300mA for Hardware Reversion.A2)
• Max.power dissiation:200mW(3W for Hardware Reversion.A2)
• Isolation Voltage:5000Vrms

# Watchdog Function

• Module internal watchdog timer : 150msec
• Power failure threshold : 4.65 V
• Safe value : 15 output channels
• Host programmable watchdog :100 ms \~ 25.5 sec

# ♦ Power

• Power supply : +10V to +30V
• Current consumption : 0.3 W(Max 3.5W for Hardware Reversion.A2)

# 1.6.4 A Look at ND-6056 & Pin Assignment

![15-CH Isolated\nDigital Output\nND-6056\nOutput Type Channels\nDO 15\nDO9 DO8 DO7 DO6 DO5 DO4 DO3 DO2 DO1 DO0\n1\nDO10 DO11 DO12 DO13 Ext.GND DEFAULT (Y)DATA+ (G)DATA- (R)+Vs (B)GND 10](.nd-6058-manual-2/ea79fc50e4fb88d593d44252eda3a0e304859e243e4d9a0bafb7f4d5c6d55c53.jpg)

# 1.6.5 Pin Definitions of NuDAM-6056

<table><tr><td>Pin #</td><td>Signal Name</td><td>Description</td></tr><tr><td>1</td><td>DO10</td><td>Digital output channel 10</td></tr><tr><td>2</td><td>DO11</td><td>Digital output channel 11</td></tr><tr><td>3</td><td>DO12</td><td>Digital output channel 12</td></tr><tr><td>4</td><td>DO13</td><td>Digital output channel 13</td></tr><tr><td>5</td><td>ExtGND</td><td></td></tr><tr><td>6</td><td>Default*/DO14</td><td>Initial state settingDigital output channel 14</td></tr><tr><td>7</td><td>(Y) DATA+</td><td>RS-485 series signal, positive</td></tr><tr><td>8</td><td>(G) DATA-</td><td>RS-485 series signal, negative</td></tr><tr><td>9</td><td>(R) +VS</td><td>Power supply, +10V~+30V</td></tr><tr><td>10</td><td>(B) GND</td><td>Ground</td></tr><tr><td>11</td><td>DO0</td><td>Digital output channel 0</td></tr><tr><td>12</td><td>DO1</td><td>Digital output channel 1</td></tr><tr><td>13</td><td>DO2</td><td>Digital output channel 2</td></tr><tr><td>14</td><td>DO3</td><td>Digital output channel 3</td></tr><tr><td>15</td><td>DO4</td><td>Digital output channel 4</td></tr><tr><td>16</td><td>DO5</td><td>Digital output channel 5</td></tr><tr><td>17</td><td>DO6</td><td>Digital output channel 6</td></tr><tr><td>18</td><td>DO7</td><td>Digital output channel 7</td></tr><tr><td>19</td><td>DO8</td><td>Digital output channel 8</td></tr><tr><td>20</td><td>DO9</td><td>Digital output channel 9</td></tr></table>

# 1.6.6 ND-6056 Functional Block Diagram

![Based on the provided diagram, here is an accurate and concise description of the blocks and connections:\n\n**Blocks:**\n*   **Power Section:** 'Power Input +10V ~ +30V', 'Power Regulator & Filter', '+5V', 'GND'.\n*   **Control Section:** 'Micro Processor', 'Watchdog/Power Failure Supervisor', 'EEPROM Config Data Safe Value'.\n*   **Communication Section:** 'RS-485 Rec/Drv', 'Data +', 'Data'.\n*   **Output Section:** '+V', 'DO0', 'COM', 'DO1', 'DO12', 'DO13', 'DO14'.\n\n**Connections:**\n*   **Power:** 'Power Input +10V ~ +30V' enters the 'Power Regulator & Filter' block. This block outputs '+5V' and 'GND'.\n*   **Central Processing:** The 'Micro Processor' is the central hub.\n    *   It is connected bidirectionally (double arrow) to the 'Watchdog/Power Failure Supervisor'.\n    *   It is connected bidirectionally to the 'RS-485 Rec/Drv' block.\n    *   It receives an input (arrow pointing to it) from the 'EEPROM Config Data Safe Value' block.\n*   **Data Inputs:** The 'RS-485 Rec/Drv' block outputs 'Data +' and 'Data' (arrows pointing left).\n*   **Control Outputs:** The 'Micro Processor' drives several output channels:\n    *   It connects to a schematic block (dotted outline) containing a diode and transistor, labeled with '+V', 'DO0', and 'COM'.\n    *   It connects to a dotted block labeled 'DO1' and 'COM'.\n    *   It connects to three stacked dotted blocks labeled 'DO12' / 'COM', 'DO13' / 'COM', and 'DO14' / 'COM'.](.nd-6058-manual-2/b4d8cb2acd645bcbb75d0eed495ca63b3260af36e24754454718e147b669446e.jpg)

# 1.7 Overview of NuDAM-6058

# 1.7.1 What is NuDAM-6058 ?

NuDAM-6058 provides 28 digital I/O channels. It emulates industry standard mode zero configuration of 8255 programmable peripheral interface (PPI) chip. The PPI offers 3 ports A, B and C, the C port can also be subdivided into 2 nibble-wide (4-bit) port – C upper and C lower. A 50 pin SCSI connector equipped with ND-6058 which is corresponding to PPI chip with 24 DIO points.

# 1.7.2 Features of NuDAM-6058

Industry standard 8255 programmable peripheral interface mode 0 emulation
24 Programmable I/O channels
♦ 4 dedicated input channels
Completely TTL compatible I/O lines
♦ Status read-back capability
♦ Direct bit set/reset capability
♦ Buffered circuits for higher driving capability
♦ Direct interface with OPTO-22 compatible I/O module
♦ Programmable host watchdog timer for host failure protection
♦ Internal watchdog timer for device failure protection
On board resetable fuse to protect power supply form external devices
Easy programming by software
♦ Easy installation and wiring

# 1.7.3 Specifications of NuDAM-6058

# ♦ Interface

• Interface : RS-485, 2 wires
• Speed (bps) : 1200, 2400, 4800, 9600, 19.2K, 38.4K, 115.2K (115.2K only for firmware reversion above A4.00)

# ♦ Programmable Digital Input/Output

• Channel numbers : 24
• Input Signal:
• Logical level 0 : -0.5 \~ 0.8 V
• Logical level 1: 2.0 \~ 5.25 V
• Output Signal:
• Logical level 0: 0.5 V Maximum
• Logical level 1: 2.4 V Minimum Digital Output

# Watchdog Function

• Module internal watchdog timer : 150msec
• Power failure threshold : 4.65 V
• Safe value : 15 output channels
• Host programmable watchdog :100 ms \~ 25.5 sec

# ♦ Dedicated Digital Input

• Channel numbers : 4
• Input Signal:
• Logical level 0: 2 V max.
• Logical level 1: 3 V \~ 5.25 V

# ♦ Connector

• 10-pin skew terminal block

• 50-pin SCSI II connector

# ♦ Power

• Power supply : +10V to +30V

• Current consumption: 1.7 W

# 1.7.4 A Look at ND-6058 & Pin Assignment

![A0\n~ A7 B0 ~ B7 C0 ~ C7\n1 50\nND-6058\n28-CH Programmable\nDigital I/O\nType Channels\nPPI 24\nDI 4\n1 D10 D11 D12 D13 DEFAULT* (Y)DATA+ (G)DATA- (R)+Vs (BG)ND 10](.nd-6058-manual-2/bdf53a224e753cfbc05c076f83bdb76c385ab97e3ec0e76f4fc710377c9d9e22.jpg)

# 1.7.5 Pin Definitions of NuDAM-6058

<table><tr><td>Pin #</td><td>Signal Name</td><td>Description</td></tr><tr><td>1</td><td>DI0</td><td>Digital input channel 0</td></tr><tr><td>2</td><td>DI1</td><td>Digital input channel 1</td></tr><tr><td>3</td><td>DI2</td><td>Digital input channel 2</td></tr><tr><td>4</td><td>DI3</td><td>Digital input channel 3</td></tr><tr><td>5</td><td></td><td></td></tr><tr><td>6</td><td>Default*</td><td>Initial state setting</td></tr><tr><td>7</td><td>(Y) DATA+</td><td>RS-485 series signal, positive</td></tr><tr><td>8</td><td>(G) DATA-</td><td>RS-485 series signal, negative</td></tr><tr><td>9</td><td>(R) +VS</td><td>Power supply, +10V~+30V</td></tr><tr><td>10</td><td>(B) GND</td><td>Ground</td></tr></table>

![A0\n1\n2\n3\n4\n5\n6\n7\n8\n9\nB0\n10\n11\n12\n13\n14\n15\n16\n17\nC0\n18\n19\n20\n21\n22\n23\n24\n25\n+5V\nFuse\n26\n27\n28\n29\n30\n31\n32\n33\n34\n35\n36\n37\n38\n39\n40\n41\n42\n43\n44\n45\n46\n47\n48\n49\n50\n+Vs\nFuse\n50Pin SCSI](.nd-6058-manual-2/e6043cbaedf116468b4951526bf43452ec05141a3d77c5b8dad85ec6661e51fa.jpg)

# 1.7.6 ND-6058 Functional Block Diagram

![The image displays a block diagram centered on a rectangular block labeled **Power Regulator & Filter**.\n\n**Connections:**\n*   **Input:** On the left, two horizontal lines labeled **Power Input** and **+10V ~ +30V** point into the left side of the central block.\n*   **Output:** On the right, two horizontal lines emerge from the right side of the block. The top line has an arrow pointing upwards labeled **+5V**, and the bottom line has an arrow pointing upwards labeled **GND**. Both lines have arrows pointing further to the right.](.nd-6058-manual-2/3f4bb12e374adddf92de40bac30bd211df4c38c19243e0785face7bdbfdec5c3.jpg)

![The block diagram centers around a **Micro Processor** block connected to various peripherals and external signals:\n\n*   **Watchdog/Power Failure Supervisor**: Connected bidirectionally to the Micro Processor.\n*   **RS-485 Rec/Drv**: Connected bidirectionally to the Micro Processor. This block has outputs labeled **Data +** and **Data -** pointing to the left.\n*   **PPI**: Connected to the Micro Processor. It receives inputs labeled **A0~A7**, **B0~B7**, and **C0~C7**.\n*   **EEPROM Config Data Safe Value**: Connected bidirectionally to the Micro Processor.\n*   **DI0 ... ... DI3**: Connected as an input to the Micro Processor.](.nd-6058-manual-2/094f614cd41c4b1dfdb40a08c8171f31bf3d634bf6a492159225e5ea2e2b154f.jpg)

# 1.8 Overview of NuDAM-6060

# 1.8.1 What is NuDAM-6060 ?

NuDAM-6060 provides four relay output channels, two are form A and two are form C. It can control high power devices without external circuits. The isolation guarantees the industrial safety.

# 1.8.2 Features of NuDAM-6060

♦ 4 channels relay output
♦ 4 channels isolated digital input
Programmable host watchdog timer for host failure protection
♦ Internal watchdog timer for device failure protection
Easy programming by software
Easy installation and wiring

# 1.8.3 Specifications of NuDAM-6060

♦ Interface
• Interface : RS-485, 2 wires
Speed (bps) : 1200, 2400, 4800, 9600, 19.2K, 38.4K, 115.2K (115.2K only for firmware reversion above A4.00)
♦ Input
• Channel numbers : 4
• Common External Voltage : +24 V
• Input Type : Source Type

♦ Output

• Channel numbers : 4 relay output
• Output type : 2 form C channels, 2 form A channels
• Contact rating : AC 0.6A /125 V, 0.3A / 250V

• DC 2A / 30V, 0.6A / 110V
• Relay ON/OFF time interval : 3 ms / 1ms
• Breakdown voltage : 500 V
• Expected life : ${ 1 0 } ^ { 8 }$ times
• Insulation resistance : 1000 MΩ minimum

# ♦ Watchdog Function

• Module internal watchdog timer : 150ms
• Power failure threshold : 4.65 V
• Safety value : 4 output channels
• Host programmable watchdog : 100 ms \~ 25.5 sec

# ♦ Power

• Power supply : +10V to +30V
• Current consumption : 0.8 W

# 1.8.4 Using Relay Output

The ND-6060 contains two types of relay : Form C and Form A. The relay R3 and R4 are form C relays, and R1 and R2 are plain form A type. The difference between these two types of relay are:

# 1. Form C Relay : ( R3, R4)

![Based on the provided image, here is an accurate description of the flowchart/block diagram:\n\n**Labeled Blocks:**\n*   **NO** (Top Left)\n*   **NC** (Middle Left)\n*   **COM** (Middle Right)\n*   **Control Bit = High (1)** (Bottom Center)\n\n**Connections and Layout:**\n*   **NO Contact:** A solid black circle is positioned below the 'NO' label. Directly below this circle is a downward-pointing arrow.\n*   **NC Contact:** An open circle is positioned below the 'NC' label. An upward-pointing arrow extends from the top of this circle towards the left end of a diagonal line.\n*   **Switch Arm/Connection:** A diagonal line segment (representing a switch arm) runs from the upper left to the lower right. Its left end is positioned between the downward arrow (from the NO side) and the upward arrow (from the NC side). Its right end connects directly to an open circle labeled **COM**.\n*   **Condition:** The text **Control Bit = High (1)** is centered at the bottom, indicating the active state that results in the configuration shown.](.nd-6058-manual-2/d6af300f730ceab81e333372c292f505c13c9f095d1ae331cb40290d09f2847f.jpg)

![Based on the provided image, here is the accurate and concise description:\n\n**Labeled Blocks and Text:**\n*   **NO** (top left)\n*   **NC** (bottom left)\n*   **COM** (middle right)\n*   **Control Bit = Low (0)** (bottom center)\n\n**Connections and Diagram Structure:**\n*   **NO Connection:** The text 'NO' is positioned above a solid black circle. A downward-pointing arrow originates below this black circle.\n*   **NC Connection:** To the left of a hollow circle is the text 'NC'. An upward-pointing arrow originates from this hollow circle, pointing towards a diagonal line.\n*   **COM Connection:** To the right of a hollow circle is the text 'COM'.\n*   **Central Link:** A diagonal line connects the hollow circle associated with 'NC' to the hollow circle associated with 'COM'. This indicates a closed connection between the NC and COM terminals.\n*   **Overall State:** The diagram illustrates that when the **Control Bit = Low (0)**, the **NC** contact is closed (connected to **COM**), while the **NO** contact is open (indicated by the separate black circle and downward arrow).](.nd-6058-manual-2/0990f9607f4fca1b3faee309bab350a73e8ab9364aeea042a813eeb6c2607e62.jpg)

Form C relay has three contacts : NC ( Normal Close), NO ( Normal Open), and COM( Common). The CM post, located at the middle, can make contact either NO post or NC post. When the control bit is high (1), the COM post and NO post are contacted. If the control bit is low (0), the COM post and NC post make contact.

In normal power-up and reset, the relay is in low status.

# 2. Form A Relay : ( R1, R2)

![NO\nCOM\nControl Bit = High (1)](.nd-6058-manual-2/97e7cbe877ceadcef9facdb91d50447c3ff22f504e38b752048809b5f205b17c.jpg)

![The diagram displays a schematic representation of an electrical contact with the following elements:\n\n*   **Top:** The text '**NO**' appears at the top left. Below it is a black circle with a downward-pointing arrow.\n*   **Middle:** The arrow points to a switch symbol. This symbol consists of a diagonal line (representing a contact arm) angled upwards and a small circle terminal to its right labeled '**COM**'. The gap between the line and the terminal indicates the switch is open.\n*   **Bottom:** The text '**Control Bit = Low (0)**' is centered at the bottom.](.nd-6058-manual-2/d771c9845e3492c2c83bff61dfe90512f58f2d7e0ba710b7e3712fe509334340.jpg)

Form A relay only has two contacts : NO (Normal Open) and COM( Common). The COM post can make contact either NO post or not contact NO post. When the control bit is high (1), the COM post and NO post are contacted. If the control bit is low (0), the COM post and NO post does not make contact. In normal power-up and reset, the relay is in low status.

# 1.8.5 A Look at ND-6060 & Pin Assignment

![20\nRL4 COM\nRL4 NC\nRL4 NO\nRL3 COM\nRL3 NC\nRL3 NO\nRL2 COM\nRL2 NO\nRL1 COM\nRL1 NO\n11\nND-6060\nRelay Output\nDigital Input\nType	Channels\nRelay Output	4\nDigital Input	4\nDI 3	DI 2	DI 1	DI 0	Ext24V	DEFAULT	(Y)DATA+	(G)DATA-\n		(R)+Vs	(B)GND\n10	(D)GND](.nd-6058-manual-2/7b6c92c5ca93f7f00f0f3d8240f1daaacb772151f94d5350ad1661d85053f2cd.jpg)

# 1.8.6 Pin Definitions of NuDAM-6060

<table><tr><td>Pin #</td><td>Signal Name</td><td>Description</td></tr><tr><td>1</td><td>DI3</td><td>Digital Input Channel 3</td></tr><tr><td>2</td><td>DI2</td><td>Digital Input Channel 2</td></tr><tr><td>3</td><td>DI1</td><td>Digital Input Channel 1</td></tr><tr><td>4</td><td>DI0</td><td>Digital Input Channel 0</td></tr><tr><td>5</td><td>Ext24</td><td>External Common +24V</td></tr><tr><td>6</td><td>Default*</td><td>Initial state setting</td></tr><tr><td>7</td><td>(Y) DATA+</td><td>RS-485 series signal, positive</td></tr><tr><td>8</td><td>(G) DATA-</td><td>RS-485 series signal, negative</td></tr><tr><td>9</td><td>(R) +VS</td><td>Power supply, +10V~+30V</td></tr><tr><td>10</td><td>(B) GND</td><td>Ground</td></tr><tr><td>11</td><td>RL1 NO</td><td>Relay 1, normal open</td></tr><tr><td>12</td><td>RL1 COM</td><td>Relay 1, common ground</td></tr><tr><td>13</td><td>RL2 NO</td><td>Relay 2, normal open</td></tr><tr><td>14</td><td>RL2 COM</td><td>Relay 2, common ground</td></tr><tr><td>15</td><td>RL3 NO</td><td>Relay 3, normal open</td></tr><tr><td>16</td><td>RL3 NC</td><td>Relay 3, normal close</td></tr><tr><td>17</td><td>RL3 COM</td><td>Relay 3, common ground</td></tr><tr><td>18</td><td>RL4 NO</td><td>Relay 4, normal open</td></tr><tr><td>19</td><td>RL4 NC</td><td>Relay 4, normal close</td></tr><tr><td>20</td><td>RL4 COM</td><td>Relay 4, common ground</td></tr></table>

# 1.8.7 ND-6060 Functional Block Diagram

![Based on the provided diagram, here are the labeled blocks and their connections:\n\n**Labeled Blocks:**\n*   Power Input +10V ~ +30V\n*   Power Regulator & Filter\n*   Watchdog/Power Failure Supervisor\n*   RS-485 Rec/Drv\n*   Micro Processor\n*   EEPROM Config Data Safe Value\n\n**Connections:**\n*   **Power Input +10V ~ +30V** connects to **Power Regulator & Filter**.\n*   **Power Regulator & Filter** outputs **+5V** and **GND**.\n*   **Power Regulator & Filter** connects to **Micro Processor** (supplying power).\n*   **Micro Processor** connects bidirectionally to **Watchdog/Power Failure Supervisor**.\n*   **Micro Processor** connects bidirectionally to **RS-485 Rec/Drv**.\n*   **RS-485 Rec/Drv** outputs **Data+** and **Data -**.\n*   **Micro Processor** connects to **EEPROM Config Data Safe Value**.\n*   **Micro Processor** connects to a dotted box labeled **Ext24V** and **DI3**.\n*   **Micro Processor** connects to transistor circuits that drive coils, leading to outputs labeled **RL1 NO**, **RL1 COM**, **RL4 NO**, and **RL4 COM**.\n*   There is an input circuit connected to **+5V** involving a resistor, diode, and zener diodes, labeled **DI0**.](.nd-6058-manual-2/9fbb99e26d186daeba7dabd85bc0b71fd43e7cd3b339c733612a58efd105a76e.jpg)

# 1.9 Overview of NuDAM-6063

# 1.9.1 What is NuDAM-6063 ?

NuDAM-6063 provides eight from A relay output channels. It can control high power devices without external circuits.

# 1.9.2 Features of NuDAM-6063

♦ 8 channel relay output
Programmable host watchdog timer for host failure protection
♦ Internal watchdog timer for device failure protection
♦ Easy programming by software
♦ Easy installation and wiring

# 1.9.3 Specifications of NuDAM-6063

♦ Interface
• Interface : RS-485, 2 wires
Speed (bps) : 1200, 2400, 4800, 9600, 19.2K, 38.4K, 115.2K (115.2K only for firmware reversion above A4.00)
Digital Output
• Channel numbers : 8
• Output Type : 8 form A channels
• Contact rating : AC 0.5A / 125V
• DC 1A / 30V
• Relay ON/OFF time interval : 3ms / 3ms
• Breakdown voltage : 1000Vrms
• Expected life : 107
♦ Insulation Resistance: 1,000 MΩ
A Watchdog Function

• Module internal watchdog timer : 150ms
• Power failure threshold : 4.65 V
• Safety value : 8 output channels
• Host programmable watchdog : 100 ms \~ 25.5 sec

# ♦ Power

• Power supply : +10V to +30V
• Current consumption : 1.2 W

# 1.9.4 Using Relay Output

Form A Relay :
![NO\nCOM\nControl Bit = High (1)](.nd-6058-manual-2/c35e78e6a37e619fc26c46a711395a9294c0a93f6a6e472fb32ca2cedb914e00.jpg)

![NO\nCOM\nControl Bit = Low (0)](.nd-6058-manual-2/1471d142f5561c46a3e3fdb68dbdf53a48948ae1959e453e1d3f685e3d719865.jpg)

Form A relay only has two contacts : NO (Normal Open) and COM( Common). The COM post can make contact either NO post or not contact NO post. When the control bit is high (1), the COM post and NO post are contacted. If the control bit is low (0), the COM post and NO post does not make contact.

In normal power-up and reset, the relay is in low status.

# 1.9.5 A Look at ND-6063 & Pin Assignment

![20\nRL5 COM\nRL5 NO\nRL4 COM\nRL4 NO\nRL3 COM\nRL3 NO\nRL2 COM\nRL2 NO\nRL1 COM\nRL1 NO\n11\nND-6063\n8-CH Isolated\nRelay Output\nType	Channels\nRelay Output	8\n1\nRL6 NO	RL6 COM	RL7 NO	RL7 COM	RL8 NO	DEFAULT*1	RL8 COM	Y)DATA+\n(G)DATA-\n(R)+Vs	(B)GND\n10](.nd-6058-manual-2/ff531827eb625364ea624723729be5c0f7dd60a282dc06675cb40a61f51982b8.jpg)

# 1.9.6 Pin Definitions of NuDAM-6063

<table><tr><td>Pin #</td><td>Signal Name</td><td>Description</td></tr><tr><td>1</td><td>RL6 NO</td><td>Relay 6, normal open</td></tr><tr><td>2</td><td>RL6 COM</td><td>Relay 6, common ground</td></tr><tr><td>3</td><td>RL7 NO</td><td>Relay 7, normal open</td></tr><tr><td>4</td><td>RL7 COM</td><td>Relay 7, common ground</td></tr><tr><td>5</td><td>RL8 NO</td><td>Relay 8, normal open</td></tr><tr><td>6</td><td>Default*/ RL8 NO</td><td>Initial state settingRelay 8, normal open</td></tr><tr><td>7</td><td>(Y) DATA+</td><td>RS-485 series signal, positive</td></tr><tr><td>8</td><td>(G) DATA-</td><td>RS-485 series signal, negative</td></tr><tr><td>9</td><td>(R) +VS</td><td>Power supply, +10V~+30V</td></tr><tr><td>10</td><td>(B) GND</td><td>Ground</td></tr><tr><td>11</td><td>RL1 NO</td><td>Relay 1, normal open</td></tr><tr><td>12</td><td>RL1 COM</td><td>Relay 1, common ground</td></tr><tr><td>13</td><td>RL2 NO</td><td>Relay 2, normal open</td></tr><tr><td>14</td><td>RL2 COM</td><td>Relay 2, common ground</td></tr><tr><td>15</td><td>RL3 NO</td><td>Relay 3, normal open</td></tr><tr><td>16</td><td>RL3 COM</td><td>Relay 3, common ground</td></tr><tr><td>17</td><td>RL4 NO</td><td>Relay 4, normal open</td></tr><tr><td>18</td><td>RL4 COM</td><td>Relay 4, common ground</td></tr><tr><td>19</td><td>RL5 NO</td><td>Relay 5, normal open</td></tr><tr><td>20</td><td>RL5 COM</td><td>Relay 5, common ground</td></tr></table>

# 1.9.7 ND-6063 Functional Block Diagram

![**Labeled Blocks:**\n*   Power Regulator & Filter\n*   Watchdog/Power Failure Supervisor\n*   RS-485 Rec/Drv\n*   Micro Processor\n*   EEPROM Config Data Safe Value\n\n**Connections:**\n*   **Power Section:**\n    *   'Power Input +10V ~ +30V' connects with a double arrow to the 'Power Regulator & Filter'.\n    *   'Power Regulator & Filter' has an arrow pointing up to '+5V'.\n    *   'Power Regulator & Filter' has an arrow pointing right to 'GND'.\n\n*   **Microprocessor Interconnections:**\n    *   'Watchdog/Power Failure Supervisor' connects with a double-headed arrow to the 'Micro Processor'.\n    *   'RS-485 Rec/Drv' connects with double-headed arrows to the 'Micro Processor'.\n    *   'RS-485 Rec/Drv' has arrows pointing left to 'Data+' and 'Data -'.\n    *   'EEPROM Config Data Safe Value' connects with an arrow pointing right to the 'Micro Processor'.\n\n*   **Relay/Transistor Circuits:**\n    *   **Top Circuit:** A line with an arrow pointing up connects the base of a transistor to the 'Micro Processor'. The transistor collector connects to a coil, which connects to a switch labeled 'RL1 NO' and 'RL1 COM'. The transistor emitter connects to ground.\n    *   **Bottom Circuit:** A line with an arrow pointing up connects the base of a transistor to the 'Micro Processor'. The transistor collector connects to a coil (near '+5V'), which connects to a switch labeled 'RL8 NO' and 'RL8 COM'. The transistor emitter connects to ground.](.nd-6058-manual-2/6c3bac32be2a50ff91952f0937be5e28ed78f3172e0570c5f8f45273064dfda9.jpg)

![2](.nd-6058-manual-2/e38801ee63e0721e808d3bb2011a677b91522e7a8fb9d83e8ecc9c3d2668e155.jpg)

# Initialization & Installation

# 2.1 Software Installation

1. If you have already installed “NuDAM Administration” then skip other steps.
2. Backup your software diskette.
3. Insert “NuDAM Administration” disc into CD-ROM.
4. Change drive to the path of CD-ROM. For example, your drive of CD-ROM is F:, then change the drive to F:
5. Find the setup of NuDAM Administration and run it.
6. Please follow the steps of setup program then you can successful to install the nudism Administration.

# 2.2 Initializing a Brand-New Module

# 2.2.1 Objective of Initializing a Brand-New NuDAM

All NuDAM modules. except NuDAM-6520 and NuDAM-6510, in a RS-485 network must have an unique address ID, however, every brand-new NuDAM has a factory default setting as following :

♦ Address ID is 01.
♦ Baud rate is 9600 bps
♦ Check-sum disable
♦ Host Watchdog timer is disable

Therefore, to configure the brand-new NuDAM before using is necessary, otherwise the address ID will be conflict with others modules because the ID of new modules are identity . The baud rate may also be changed according to user‘s requirements.

The following sections show how to initialize a brand-new module, which is applicable for initializing NuDAM-6050, NuDAM-6052, NuDAM-6053, NuDAM-6054, NuDAM-6056, NuDAM-6058, NuDAM-6060, and NuDAM-6063.

# 2.2.2 Default State

The NuDAM I/O modules must be set at Default State when you want to change the default settings, such as the ID address, baud rate, check-sum status etc. All NuDAM I/O modules have an special pin labeled as DEFAULT\*. The module will be in Default State if the DEFAULT\* pin is shorted to ground when power ON. Under this state, the default configuration is set as following :

♦ Address ID is 00
♦ Baud rate is 9600 bps
♦ Check-sum disable

Therefore, the communication between host and the module will can be easily set as the same configuration, the initialization of a module will be possible no matter what configuration is set under operating state.

For ND-6053, ND-6054 and ND-6056, the pin 6 is used for both DI15(DO15) and DEFAULT\*, and also the ND-6063, the pin 6 is used for both RL8 COM and DEFAULT\*. The jumper setting is as below, and the default setting is DI15(D015) or RL8 COM. When you want to use ND-6053, ND-6054, ND-6056 or ND-6063 as Default\*, you should open the module case to set the JP2.

![JP2\n1 2 3\nDI15 INIT*\n(DO15)\nDI15, DO15, RL8 COM](.nd-6058-manual-2/ac9e40534667e727ef6943de26411f86c7feb238710ab95ec476f38894d4997f.jpg)

![JP2\n1 2 3\nDI15 INIT*\n(DO15)\nINIT*](.nd-6058-manual-2/266ca350fa5a79ec47f614007e20fad9961817a94a33e95ac3bf590294c9e275.jpg)

# 2.2.3 Initialization Equipments

Host computer with an RS-232 port
♦ An installed RS-485 module (NuDAM-6520) with 9600 baud rate
♦ The brand new NuDAM module
Power supply (+10 to +30 VDC) for NuDAM modules
♦ Administration utility software

Note1: Never Connect the DRFAULT\* pin to Vs or power source just left it open or wired to GND.

# 2.2.4 Initialization Procedure

1. Power off the host computer and the installed NuDAM-6520. Be sure of the baud rate of the NuDAM-6520 is 9600 bps.
2. Connect a brand new NuDAM module with the RS-485. Set the module in Default State by shorting the DEFAULT\* pin. Refer to Figure 2.1 for detailed wiring.
3. Power on the host computer.
4. Power on the power supply for NuDAM modules.
5. Use the NuDAM Administrating utility to configure the address ID, Baud rate and check-sum status of the module.

# 2.2.5 Initialization Wiring

![Based on the provided image, here is a description of the flowchart/block diagram:\n\n**Labeled Blocks:**\n*   **Host Computer** (Top Left)\n*   **Local Power Supply** (Bottom Left) containing text: '+10 V to +30 V', '+Vs', 'GND'.\n*   **NuDAM-6520 RS-232/RS-485 Converter** (Center). An arrow points to it from above. Inside the block, the text reads: 'DATA +', 'DATA -', '+Vs', 'GND'.\n*   **New NuDAM module** (Right). An arrow points to it from above. Inside the block, the text reads: 'DATA+', 'DATA -', 'Default*', '+Vs', 'GND'.\n*   There is an unlabeled rectangular block with a smaller inner rectangle situated below the 'Host Computer'.\n\n**Connections:**\n*   **Host Computer** connects via a vertical line to the unlabeled block below it.\n*   The unlabeled block connects to the left side of the **NuDAM-6520** block via a horizontal line. This line features a small box labeled **'RS-232'**.\n*   **Local Power Supply** connects to the **+Vs** and **GND** terminals of both the **NuDAM-6520** block and the **New NuDAM module** block via separate horizontal lines at the bottom.\n*   Two horizontal lines connect the right side of the **NuDAM-6520** block to the left side of the **New NuDAM module** block.\n*   On the far right edge, a thick black line connects the bottom-most wire (associated with **GND**) to the wire directly above it.](.nd-6058-manual-2/73f5ecf9e9c2a2174e5b4788c6a3a3e4d0f9ba16590dda5eb79b4e2eeaf37549.jpg)

Figure 2-1 Layout for Configuring the NuDAM module

# 2.3 Install a New NuDAM to a Existing Network

# 2.3.1 Equipments for Install a New Module

♦ A existing NuDAM network
♦ New NuDAM modules.
Power supply (+10 to +30 VDC)

# 2.3.2 Installing Procedures

1. Configure the new NuDAM module according to the initialization procedure in section 2.2.
2. The baud rate and check-sum status of the new module must be identity with the existing RS-485 network. The address ID must not be conflict with other NuDAM modules on the network.
3. Power off the NuDAM power supply of the existing RS-485 network.
4. Power off the host computer.
5. Wire the power lines for the new NuDAM with the existing network. Be careful about the signal polarity as wiring.
6. Wire the RS-485 data lines for the new NuDAM with the existing network. Be careful about the signal polarity as wiring.
7. Wire to the input or output devices. Refer to section 2.4 for illustrations.
8. Power on the host computer.
9. Power on the NuDAM local power supply.
10. Use the NuDAM administration utility to check entire network.

# 2.4 Application Wiring for NuDAM-6050

Digital Input Connect with TTL Signal
![NuDAM-6050 Digital Input Channel\nTTL Buffer\n+5V\nTTL Device\nDI n\nGND\nTo Micro Processor](.nd-6058-manual-2/9ed92a2efc2e072ba230c4f86410c58b836ef966ee3629023995ac8de40f9f21.jpg)

Digital Input Connect with Switch or Push Button
![NuDAM-6050 Digital Input Channel\nSwitch\nor\nPush Button\nDI n\nGND\n+5V\nTTL Buffer\nTo\nMicro Processor](.nd-6058-manual-2/f34474cae2dcc2038b1e3ad0a920efe49aee05b0e766363750265c99ad1950d5.jpg)

Digital Output Connect with Power Loading

![This diagram illustrates the circuit for a **NuDAM-6050 Digital Output Channel**, enclosed within a dashed boundary.\n\n**Inside the dashed box:**\n*   An input labeled **'From Micro Processor'** points via an arrow to the base of a transistor.\n*   The text **'open collector'** is placed near the transistor.\n*   The transistor's collector connects to a terminal labeled **'DO n'** (depicted with a screw terminal symbol).\n*   The transistor's emitter connects to a terminal labeled **'GND'** (depicted with a screw terminal symbol) and a ground symbol.\n\n**Outside the dashed box (External Circuit):**\n*   A block labeled **'Power Loading'** is connected to the **'DO n'** line.\n*   The text **'LED, SSR, Relay etc.'** points to the **'Power Loading'** block.\n*   A voltage source labeled **'+Vs'** connects to a resistor **'R'**.\n*   Resistor **'R'** connects to the top of the **'Power Loading'** block.\n*   The **'GND'** terminal line extends to the right and connects to a ground symbol.\n*   The label **'External Power Supply'** with vertical arrows indicates the power range covering **'+Vs'** and the ground connection.](.nd-6058-manual-2/ba2895911366d37ab3f3be7764aaaf42292dd42db70febf0d4b63a4330dd4f8a.jpg)

R : current limit resistor

# 2.5 Application Wiring for NuDAM-6052

Isolated Differential Input
![The image displays a block diagram titled 'NuDAM-6052 Differential Input Channel'.\n\n**Labeled Blocks:**\n*   **Floating Digital Signal Source**: A rounded rectangle on the left.\n*   **Terminal Block**: A vertical rectangle containing three screw terminal icons labeled 'DI n+', 'DI n-', and 'GND'.\n*   **Photo Coupler**: A rounded rectangle containing a schematic symbol (LED and phototransistor) labeled 'Photo Coupler'.\n*   **To Micro Processor**: Text indicating the output destination.\n\n**Connections:**\n*   Two lines extend from the 'Floating Digital Signal Source' and connect to the 'DI n+' and 'DI n-' terminals respectively.\n*   A line connects the 'DI n+' terminal to the input side of the 'Photo Coupler'.\n*   A line connects the 'DI n-' terminal to the 'GND' terminal.\n*   The 'GND' terminal connects to the output side (emitter) of the 'Photo Coupler'.\n*   An arrow extends from the 'Photo Coupler' to the right, labeled 'To Micro Processor'.](.nd-6058-manual-2/4a32dd50813467acb0edc6e2566b243c88817ea184c6650f1d4dde4d1a1235b1.jpg)

Isolated Single Ended Input
![Based on the provided block diagram, here is the accurate description:\n\n**Labeled Blocks and Components:**\n*   **Digital Signal Source** (Input block)\n*   **NuDAM-6052 Single-ended Input Channel** (Dashed container)\n*   **DI n+** (Input terminal)\n*   **GND** (Ground terminal)\n*   **Photo Coupler** (Component containing a schematic symbol)\n*   **To Micro Processor** (Output label)\n\n**Connections:**\n*   The **Digital Signal Source** connects to the **DI n+** terminal.\n*   The **Digital Signal Source** connects to the **GND** terminal.\n*   Inside the **NuDAM-6052 Single-ended Input Channel**, the **DI n+** terminal connects to the input (anode) of the **Photo Coupler**.\n*   The **GND** terminal connects to the ground symbol and also connects to the common side of the **Photo Coupler** (linking the cathode of the LED and the emitter of the transistor).\n*   The output (collector) of the **Photo Coupler** connects to the arrow labeled **To Micro Processor**.](.nd-6058-manual-2/b36aa3395c3296016736fff7520d53f66f4b776b633d2885b379cf2c16a0afa1.jpg)

# 2.6 Application Wiring for NuDAM-6053

Wet Contact Input
![0~+30VDC\nDI n\nGND\nVcc\nDigital\nGND](.nd-6058-manual-2/f13579f9d730114d808ef6386c853baac25c34f00cbbc4fce60f1ca54ae29d9c.jpg)

Contact Closure Input
![Contact\nClosure\nDI n\nGND\nVcc\nDigital\nGND](.nd-6058-manual-2/7e9fdeb912ff1a777a856080467e16d46fbcbc873a2611c71f1eb81e65b3913c.jpg)

# 2.7 Application Wiring for NuDAM-6054

Isolated Common Power Input

NuDAM-6054 Common Power Channel
![Based on the provided flowchart/block diagram, here is the accurate description of the labeled blocks and their connections:\n\n**Labeled Blocks:**\n*   **Common Power.**\n*   **Digital Signal Source**\n*   **Ext.24V**\n*   **DI n**\n*   **GND**\n*   **Photo Coupler**\n*   **To Micro Processor**\n\n**Connections:**\n*   **Common Power.** connects via an arrow to the terminal labeled **Ext.24V**.\n*   **Digital Signal Source** connects via an arrow to the terminal labeled **DI n**.\n*   Inside the dashed boundary box, the **DI n** terminal connects to the input side (LED symbol) of the **Photo Coupler**.\n*   The output side (transistor symbol) of the **Photo Coupler** connects to the output line labeled **To Micro Processor**.\n*   The output side of the **Photo Coupler** also connects to the terminal labeled **GND**.\n*   The **GND** terminal connects to the ground symbol at the bottom right.](.nd-6058-manual-2/dbd529acf3e22da4de3499f7e26668399bc0d3e050d64f578342fd9b951ecae1.jpg)

# 2.8 Application Wiring for NuDAM-6056

Isolated Common Ground Output

NuDAM-6056 Common Ground Channel
![Based on the provided image, here is the description of the flowchart/block diagram:\n\n**Labeled Blocks:**\n*   **Digital Output** (Left box)\n*   **Common GND** (Left box)\n*   **DO n** (Terminal label inside the dashed area)\n*   **COM** (Terminal label inside the dashed area)\n*   **GND** (Terminal label inside the dashed area)\n*   **Photo Coupler** (Label above the internal component box)\n*   **From Micro Processor** (Label with an arrow)\n\n**Connections:**\n*   A line connects **Digital Output** to the **DO n** terminal.\n*   A line connects **Common GND** to the **COM** terminal.\n*   A line connects the **COM** terminal to the base of the transistor symbol inside the **Photo Coupler** box.\n*   An arrow from **From Micro Processor** points into the right side (diode side) of the **Photo Coupler** box.\n*   A line connects the **GND** terminal to the emitter of the transistor symbol inside the **Photo Coupler** box and continues to a ground symbol.](.nd-6058-manual-2/3fc4ab753057dc9a2be89e2bcfba4a28ff78c3b7ecbeb22ae893ce0b586d1c42.jpg)

# 2.9 Application Wiring for NuDAM-6058

Digital Input Connect with TTL Signal
![NuDAM-6058 Digital Input Channel\nTTL Device\n+5V\nDTI n\nGND\nTTL Buffer\nTo Micro Processor](.nd-6058-manual-2/095e3d0cdc6f9ba211fe25fd49f0820c61d50fa3616e2a4a2212db3a8aebb03b.jpg)

![The diagram displays a connection between two blocks:\n\n*   **Left Block:** A square box labeled **6058**.\n*   **Right Block:** A rectangular box containing a vertical list:\n    *   **DIN-24P**\n    *   **DIN-24R**\n    *   **DIN-24G**\n    *   **DIN-50S**\n*   **Connection:** Two wavy lines connect the right side of the left block to the left side of the right block.](.nd-6058-manual-2/7ad3f39b8097827df4088a9546553feef2d6ef061916b2982149c2dc2a756e22.jpg)

# DIN-24P

24-CH Opt-Isolated Digital Input Termination Board with DIN Socket.

# DIN-24R

24-CH Relay Output Termination Board with DIN Socket.

# DIN-24G

24-CH Grayhill I/O Modules Termination Board with DIN Socket.

# DIN-50S

50-Pin SCSI Connector Termination Board with DIN Socket.

# 2.10 Application Wiring for NuDAM-6060

Form C Relay Output
![The diagram, titled 'NuDAM-6060 Relay Output Channel', illustrates a relay circuit.\n\n**Labeled Blocks and Components:**\n*   **Input:** 'From Micro Processor'\n*   **Internal Components:** A coil (inductor symbol) and a switch mechanism.\n*   **Switch Terminals:** Labeled 'RL n', 'NO', 'COM', and 'NC'.\n*   **External Loads:** Two blocks labeled 'Power Loading'.\n*   **Power Source:** 'External Power Source +Vs'\n*   **Ground:** 'External power ground'\n\n**Connections:**\n1.  **Control:** Two arrows from 'From Micro Processor' point to the coil.\n2.  **Normally Open Path:** The 'RL n' / 'NO' terminal connects through a fuse (circle with a diagonal line) to the top 'Power Loading' block.\n3.  **Common Path:** The 'COM' terminal connects through a fuse to 'External power ground'.\n4.  **Normally Closed Path:** The 'NC' terminal connects through a fuse to the bottom 'Power Loading' block.\n5.  **Power Supply:** 'External Power Source +Vs' connects to the right side of both 'Power Loading' blocks.](.nd-6058-manual-2/4d41243a5f94c71037cfed924e05e66a8e9cdd564e37ea932211bfedafbfd2fe.jpg)

Form A Relay Output

![The diagram is titled **NuDAM-6060 Relay Output Channel**.\n\nInside a large dotted boundary box:\n*   A relay component receives input labeled **From Micro Processor** into its coil.\n*   The relay's switch connects to two terminal labels: **RL n NO** (top) and **COM** (bottom).\n*   Lines extending from these labels pass through circular connector symbols.\n\nOutside the boundary box, the connections are:\n*   The top connector connects to a block labeled **Power Loading**.\n*   The **Power Loading** block connects to a terminal labeled **+Vs** under the text **External Power Source**.\n*   The bottom connector connects to a ground symbol labeled **External power ground**.](.nd-6058-manual-2/ebb3a01508108d49a5a17f0fd6cc2fee512c50d8b1693d4e3c059a7784df1047.jpg)

Digital Input : Contact Mode
![The image is a block diagram titled '**NuDAM-6060 Digital Input Channel**'. It depicts the internal circuitry of a digital input module.\n\n**Labeled Blocks and Components:**\n*   **NuDAM-6060 Digital Input Channel**: The large dotted box encompassing the internal circuitry.\n*   **Ext24V**: An external voltage source input.\n*   **DI n+**: A terminal inside the channel.\n*   **DI n-**: A terminal inside the channel.\n*   **External Switch**: An external switch component.\n*   **Photo Coupler**: A rectangular block containing an LED and a phototransistor symbol.\n*   **To Micro Processor**: The output signal path.\n*   **Ground**: Represented by the earth symbol at the bottom.\n\n**Connections:**\n*   **Ext24V** connects to the **DI n+** terminal.\n*   The **DI n-** terminal connects to the **External Switch**, which then connects to **Ground**.\n*   Inside the channel, the **DI n+** and **DI n-** terminals connect to the input side (LED) of the **Photo Coupler**. (Current flows from DI n+ through the LED to DI n- when the switch is closed).\n*   The output side (phototransistor) of the **Photo Coupler** connects to the arrow labeled **To Micro Processor**.\n*   The emitter of the phototransistor within the **Photo Coupler** connects to **Ground**.](.nd-6058-manual-2/7ff67e44c4448539a881c09e9e989819ca7381e72f3ea37547672a0ba44a2a9b.jpg)

Digital Input : Transistor Mode
![The image displays a schematic block diagram titled '**NuDAM-6060 Digital Input Channel**'.\n\n**Labeled Blocks and Elements:**\n*   **Main Container:** A large rounded rectangle enclosing the internal circuitry.\n*   **Terminals:** Two circular terminals on the left side labeled '**DI n+**' (top) and '**DI n-**' (bottom).\n*   **Photo Coupler:** A smaller rounded rectangle on the right side labeled '**Photo Coupler**,' containing an LED symbol and a phototransistor symbol.\n*   **External Labels:**\n    *   '**Ext24V**' (top left)\n    *   '**External Signal**' (bottom left)\n    *   '**To Micro Processor**' (right)\n\n**Connections:**\n*   **Ext24V** connects via a line to the '**DI n+**' terminal.\n*   '**DI n+**' connects via a horizontal line to the anode of the LED inside the '**Photo Coupler**'.\n*   '**External Signal**' connects to the base of a transistor symbol. The collector of this transistor connects to the '**DI n-**' terminal, and the emitter connects to a ground symbol.\n*   '**DI n-**' connects via a horizontal line to the cathode of the LED inside the '**Photo Coupler**'.\n*   The collector of the phototransistor inside the '**Photo Coupler**' connects to an arrow pointing right, labeled '**To Micro Processor**'.\n*   The emitter of the phototransistor connects via a vertical line to a ground symbol at the bottom right.](.nd-6058-manual-2/a259e828f34616b3de4fcbb41056a772f60d49c190fd1fe740f4f4f3247ec4c1.jpg)

# 2.11 Application Wiring for NuDAM-6063

Form A Relay Output
![Based on the provided image, here is the description of the flowchart/block diagram:\n\n**Main Component:**\nA large dotted rectangular box labeled **'NuDAM-6063 Relay Output Channel'**.\n\n**Inside the Main Box:**\n*   **Input Side:** A coil symbol (inductor) with two arrows pointing into it from the text **'From Micro Processor'**.\n*   **Output Side:** A switch symbol (open contact).\n    *   The top terminal of the switch is labeled **'RL n NO'**.\n    *   The bottom terminal of the switch is labeled **'COM'**.\n\n**External Connections:**\n*   **Top Right:** Text **'External Power Source'** sits above a terminal labeled **'+Vs'**. A line connects this terminal to a rounded rectangle block labeled **'Power Loading'**.\n*   **Middle Connection:** The **'Power Loading'** block connects to the **'RL n NO'** terminal inside the main box.\n*   **Bottom Right:** The **'COM'** terminal connects via a line to a ground symbol (triangle pointing down), which is labeled **'External power ground'**.](.nd-6058-manual-2/af1cd82738eb1dec8cfab6a0243cc00596c802c02bd603ed7fe96e4678c480ab.jpg)

![3](.nd-6058-manual-2/6e3d1a208025f5ab650d8df06e716af3f4fc5413e4425e23da2ec29c609e3aea.jpg)

# Command Set

# 3.1 Command and Response

# 3.1.1 Introduction

The NuDAM command is composed by numbers of characteristics, including the leading code, address ID, the variables, the optional check-sum byte, and a carriage return to indicate the end of a command. The host computer can only command only one NuDAM module except those syncronized commands with wildcard address “\*\*”. The NuDAM may or may not give response to the command. The host should check the response to handshake with the modules.

# 3.1.2 Document Conventions

The following syntax conventions are used to describe the NuDAM commands in this manual.

<table><tr><td>(Leading Code)</td><td>Leading Code is the first characteristic of the NuDAM command. All NuDAM commands need a command leading code, such as %,$,#,@,...etc.1- character</td></tr><tr><td>(Addr)</td><td>Module&#x27;s address ID, the value is in the range of 00 - FF (Hexadecimal) if no specified in the following2- character</td></tr><tr><td>(Command Variable)</td><td>Items indicate command codes or value of variablesVariable length</td></tr><tr><td>[Data]</td><td>Some output command need dataVariable length</td></tr><tr><td>[Checksum]</td><td>Checksum in brackets indicate optional parameter, only checksum is enable then this field is required2- character</td></tr><tr><td>&lt; &gt;</td><td>Identifies a control code character, such asfor carriage return, its value is 0x0D.1- character</td></tr></table>

# 3.1.3 Format of NuDAM Commands

```txt
(Leading Code)(Addr)(Command)[Data][Checksum]&lt;CR&gt;
```

When checksum is enable then [Checksum] is needed, it is

2-character.

How to calculate checksum value ?

```powershell
[Checksum] = ((LeadingCode)+(Addr)+(Command)+[Data]) MOD 0x100
```

Example 1: checksum is disable

```txt
User Command: $012&lt;CR&gt;
Response: !01400600&lt;CR&gt;
```

```txt
$ : LeadingCode
01 : Address
2 : Command (Read Configuration)
&lt;CR&gt; : Carriage return 0x0D
```

Example 2: checksum is enable
User Command: $012B7&lt;CR&gt;
Response: !01400600AC&lt;CR&gt;

    $ : LeadingCode
    01 : Address
    2 : Command (Read Configuration)
    B7 : Checksum value
    &lt;CR&gt; : Carriage return 0x0D

' $' = 0x24    '0' = 0x30    '1' = 0x31    '2' = 0x30

B7 = ( 0x24 + 0x30 + 0x31 + 0x32 ) MOD 0x100

'!' = 0x24    '0' = 0x30    '1' = 0x31    '4' = 0x34
'6' = 0x36

AC = ( 0x24 + 0x30 + 0x31 + 0x34 + 0x30 + 0x30 + 0x36 + 0x30 + 0x30 ) MOD 0x100

Note : 1.There is no spacing between characters.

2. At end of command need a &lt;CR&gt; carriage return 0x0D.
3. Checksum is optional parameter.

# 3.1.4 Response of NuDAM Commands

The response message depends on NuDAM command. The response is also composed with several characteristics, including leading code, variables, and carriage return for ending. There are two kinds of leading code for response message, ”!“ or ”>“ means valid command and ”?“ means invalid. By checking the response message, user can monitor the command is valid or invalid.

Note : Under the following conditions, there will have no response message.

1. The specified address ID is not exist.
2. Syntax error.
3. Communication error
4. Some special commands does not have response.

# 3.2 Summary of Command Set

There are three categories of NuDAM commands. One is the general commands, including set configuration command, read configuration, reset, read module‘s name or firmware version, etc. Every NuDAM can response to the general commands.

The second category is the functional commands, which depends on functions of each module, not every module can execute all functions.

The third category is the special commands, including functions about the programmable watchdog timer, safe values, and the programmable leading code.

<table><tr><td colspan="3">Command Set of Digital I/O Modules</td></tr><tr><td>Command</td><td>Syntax</td><td>Module</td></tr><tr><td colspan="3">General Commands</td></tr><tr><td>Set Configuration</td><td>%(OldAddr)(NewAddr)(TypeCode)(BaudRate)(CheckSumFlag)</td><td>ALL</td></tr><tr><td>Read Configuration</td><td>$(Addr)2</td><td>ALL</td></tr><tr><td>Read Module Name</td><td>$(Addr)M</td><td>ALL</td></tr><tr><td>Read Firmware Version</td><td>$(Addr)F</td><td>ALL</td></tr><tr><td>Reset Status</td><td>$(Addr)5</td><td>ALL</td></tr><tr><td colspan="3">Functional Commands</td></tr><tr><td>Synchronized Sampling</td><td>#**</td><td>6050, 6052, 6053, 6054, 6058, 6060</td></tr><tr><td>Read Synchronized Data</td><td>$(Addr)4</td><td>6050, 6052, 6053, 6054, 6058, 6060</td></tr><tr><td>Digital Output</td><td>#(Addr)(ChannelNo)(OutData)</td><td>6050, 6060, 6063</td></tr><tr><td></td><td>#(Addr)(Port)(Odata)</td><td>6056, 6058</td></tr><tr><td></td><td>#(Addr)(Port)(ChannelNo)(BitData)</td><td>6056,6058</td></tr><tr><td></td><td>#(Addr)T(OdataA)(OdataB)(OdataC)</td><td>6058</td></tr><tr><td>Digital Input</td><td>$(Addr)6</td><td>ALL</td></tr><tr><td>Set Programmable I/O Mode</td><td>$(Addr)S(IOSsts)</td><td>6058</td></tr><tr><td colspan="3">Special Commands</td></tr><tr><td>Read Command Leading Code Setting</td><td>~(Addr)0</td><td>ALL</td></tr><tr><td>Change Command Leading Code Setting</td><td>~(Addr)10(C1)(C2)(C3)(C4)(C5)(C6)</td><td>ALL</td></tr><tr><td>Set Host Watchdog / Safety Value</td><td>~(Addr)2(Flag)(TimeOut)(SafeValue)</td><td>ALL</td></tr><tr><td>Read Host WatchDog / Safe Value</td><td>~(Addr)3</td><td>ALL</td></tr><tr><td>Change Polarity</td><td>~(Addr)CP(Status)</td><td>ALL</td></tr><tr><td>Read Polarity</td><td>~(Addr)CR</td><td>ALL</td></tr><tr><td>Host is OK</td><td>~**</td><td>ALL</td></tr></table>

# 3.3 Set Configuration

( 6050, 6052, 6053, 6054,

6056, 6058, 6060, 6063 )

# @Description

Configure the basic setting about address ID, baud rate, and checksum.

# @Syntax

%(OldAddr)(NewAddr)(TypeCode)(BaudRate)(CheckSumFlag)&lt;CR&gt;

<table><tr><td>%</td><td>Command leading code.(1-character)</td></tr><tr><td>(OldAddr)</td><td>NuDAM module original address ID. The default address ID of a brand new module is 01. The value range of address ID is 00 to FF in hexadecimal. (2-character)</td></tr><tr><td>(NewAddr)</td><td>New address ID, if you don’t want to change address ID, let new address ID equals to the old one. (2-character)</td></tr><tr><td>(TypeCode)</td><td>Type Code is fixed 40H for Digital I/O modules. (2-character)</td></tr><tr><td>(BaudRate)</td><td>Communication baud rate, refer to Table 3-1 for details. (2-character)</td></tr><tr><td>(CheckSumFlag)</td><td>Define check-sum status, refer to Table 3-2 for details. (2-character)</td></tr></table>

# @Response

!(Addr)&lt;CR&gt;

or

?(Addr)&lt;CR&gt;

(Addr)

!

?

Address ID.

Command is valid.

Command is invalid. Invalid parameter values, When you wanted to change the setting without grounding the DEFAULT\* pin.

Note : When you want to change the checksum or baud rate then the DEFAULT\* pin should be grounded at first.

# @Example

User command: %0130400600&lt;CR&gt; Response: !30&lt;CR&gt;

<table><tr><td>Item</td><td>Meaning</td><td>Description</td></tr><tr><td>%</td><td>(Leading Code)</td><td>Command leading code.</td></tr><tr><td>01</td><td>(OldAddr)</td><td>Original address ID is 01H.</td></tr><tr><td>30</td><td>(NewAddr)</td><td>New address ID is 30H (Hexadecimal).</td></tr><tr><td>40</td><td>(TypeCode)</td><td>Digital I/O module.</td></tr><tr><td>06</td><td>(BaudRate)</td><td>Baud rate is 9600.</td></tr><tr><td>00</td><td>(CheckSumFlag)</td><td>00 means checksum is disable.</td></tr><tr><td></td><td>Carriage return</td><td>0x0D.</td></tr></table>

<table><tr><td>Code</td><td>Baudrate</td></tr><tr><td>03</td><td>1200 bps</td></tr><tr><td>04</td><td>2400 bps</td></tr><tr><td>05</td><td>4800 bps</td></tr><tr><td>06</td><td>9600 bps</td></tr><tr><td>07</td><td>19200 bps</td></tr><tr><td>08</td><td>38400 bps</td></tr><tr><td>09</td><td>115200 bps</td></tr></table>

Table 0-1 Baud rate setting code

![Checksum\n0 : disable\n1 : enable\n\n7 6 5 4 3 2 1 0\n\nReserved\nMust to be 0\nReserved\nMust to be 000000](.nd-6058-manual-2/a6fbe4e54cb954e90fcf2dede428f716c021b82bdbec085f04b1898900672975.jpg)

Table 0-2 Check sum flag setting

# 3.4 Read Configuration

( 6050, 6052, 6053, 6054,

6056, 6058, 6060, 6063 )

# @Description

Read the configuration of module on a specified address ID.

# @Syntax

```txt
$(Addr)2&lt;CR&gt;
```

\$ Command leading code

(Addr) Address ID.

2 Command code for reading configuration

# @Response

```asp
!(Addr)(TypeCode)(BaudRate)(CheckSumFalg)&lt;CR&gt;
```

```txt
?(Addr)&lt;CR&gt;
```

! Command is valid.

? Command is invalid.

(Addr) Address ID.

(TypeCode) It always be 40 (Hex) for digital I/O modules.

(BaudRate) Current setting of communication baud rate, refer to Table 3-1 for details.

(CheckSumFlag) Current setting of check-sum flag, refer to Table 3-3. for details.

Checksum

0 : disable

1 : enable

![Reserved\nMust to be 000\nReserved\nMust to be 0](.nd-6058-manual-2/30ffc7d4cfb905059da38df367b8c40aded3e81a69f711efe6daa7a1a22d9bac.jpg)

Module Type

000: ND-6050

001: ND-6060

010: ND-6052

011: ND-6053

100: ND-6058

101: ND-6063

110: ND-6054

111: ND-6056

Table 0-3 Response of check sum flag
@Example

<table><tr><td>User command:</td><td>$302</td></tr><tr><td>Response:</td><td>!30400600</td></tr><tr><td>!</td><td>Command is valid.</td></tr><tr><td>30</td><td>Address ID.</td></tr><tr><td>40</td><td>Digital I/O module.</td></tr><tr><td>06</td><td>Baud rate is 9600 bps.</td></tr><tr><td>00</td><td>checksum is disable.</td></tr></table>

# 3.5 Read Module Name

( 6050, 6052, 6053, 6054,

6056, 6058, 6060, 6063 )

# @Description

Read NuDAM module‘s name.

# @Syntax

\$(Addr)M&lt;CR&gt;

\$ Command leading code.

(Addr) Address ID.

M Read module name.

# @Response

!(Addr)(ModuleName) &lt;CR&gt;

or

?(Addr)&lt;CR&gt;

! Command is valid.

? Command is invalid.

(Addr) Address ID.

(ModuleName) NuDAM module‘s name.

# @Example

User command: \$30M&lt;CR&gt;

Response: !306050&lt;CR&gt;

! Command is valid

30 Address.

6050 ND-6050 (Digital I/O module).

# 3.6 Read Firmware Version

( 6050, 6052, 6053, 6054,

6056, 6058, 6060, 6063 )

# @Description

Read NuDAM module‘s firmware version.

# @Syntax

\$(Addr)F&lt;CR&gt;

\$ Command leading code.

(Addr) Address ID

F Read module firmware version.

# @Response

!(Addr)(FirmRev) &lt;CR&gt;

?(Addr)&lt;CR&gt;

! Command is valid.

? Command is invalid.

Address ID.

(FirmRev) NuDAM module‘s firmware version.

# @Example

User command: \$30F&lt;CR&gt;

Response: !30A1.50&lt;CR&gt;

! Command is valid.

30 Address

A1.50 Firmware Version

# 3.7 Reset Status

( 6050, 6052, 6053, 6054,

6056, 6058, 6060, 6063 )

# @Description

Checks the reset status of module at specified address to see whether it has been reset since the last reset status command was issued to the module.

# @Syntax

```txt
$(Addr)5&lt;CR&gt;
```

\$ Command leading code.

(Addr) Address ID.

5 Reset Status Command.

# @Response

```txt
!(Addr)(Status)&lt;CR&gt;
```

or

```txt
?(Addr)&lt;CR&gt;
```

! Command is valid.

? Command is invalid.

(Addr) Address ID.

(Status) 0 : It has not been reset since the last reset status command was issued.

1 : It has been reset since the last reset status command was issued.

# @Example

User command: \$305&lt;CR&gt;

Response: !300&lt;CR&gt;

Status is 0 means this digital I/O module has not been reset, since the last reset status command was issued.

# 3.8 Digital Output

( 6050, 6060, 6063 )

# @Description

Set digital output channel value at specified address. This command is only available to modules involving the digital output function.

# @Syntax

#(Addr)(ChannelNo)(OutData)&lt;CR&gt; (6050,6060,6063 Only)

```txt
# Command leading code. (1-character)
(Addr) Address ID (2-character)
00 : Set value to all channels
(ChannelNo) 1X : Set value to single channel
First character is 1, Second character is channel number. (2-character)
Set value to all channels :
Each bit is mapping to each channel number
(OutData) Set value to single channel :
First character is 0, second character is set to value 0 or 1. (2-character)
```

# @Response

&lt;CR&gt;

or

?(Addr)&lt;CR&gt;

> Command is valid

? Command is invalid.

(Addr) Address ID.

# @Example

User command: #300003&lt;CR&gt;

Response: >&lt;CR&gt;

30 Address ID

00 Set output to all channels

03 03 (00000011), Channel 0 and 1 are set ON other channels are set to OFF

User command: #2F1201&lt;CR&gt;

Response: >&lt;CR&gt;

2F Address ID

12 1 : Set output to single channel

2 : Output single channel is channel 2

01 Set single channel to ON

# 3.9 Digital Output (Continued)

( 6056, 6058 )

# @Description

Set digital output channel value at specified address. This command is only available to modules involving the multiport digital output function.

# @Syntax

#(Addr)T(OutDataH)(OutDataL)&lt;CR&gt; (6056 only)

#(Addr)T(OutDataA)(OutDataB)(OutDataC) (6058 only)

<table><tr><td>#</td><td>Command leading code. (1-character)</td></tr><tr><td>(Addr)</td><td>Address ID (2-character)</td></tr><tr><td>T</td><td>Set value to all channels</td></tr><tr><td>(OutDataH)</td><td>Each bit is mapping to each channel number from 14 to 8. (2-character)</td></tr><tr><td>(OutDataL)</td><td>Each bit is mapping to each channel number from 7 to 0. (2-character)</td></tr><tr><td>(OutDataA)</td><td>Output data for port A. Each bit is mapping to each channel number from 7 to 0. (2-character)</td></tr><tr><td>(OutDataB)</td><td>Output data for port B. Each bit is mapping to each channel number from 7 to 0. (2-character)</td></tr><tr><td>(OutDataC)</td><td>Output data for port C. Each bit is mapping to each channel number from 7 to 0. (2-character)</td></tr></table>

\* if the port of ND-6058 is in input mode, output data to this port will be ignore.

# @Response

<table><tr><td colspan="2"></td></tr><tr><td colspan="2">or</td></tr><tr><td>?(Addr)</td><td></td></tr><tr><td>&gt;</td><td>Command is valid</td></tr><tr><td>?</td><td>Command is invalid.</td></tr><tr><td>(Addr)</td><td>Address ID.</td></tr></table>

# @Example

<table><tr><td>User command:</td><td>#30T0303(for ND-6056)</td></tr><tr><td>Response:</td><td></td></tr><tr><td>30</td><td>Address ID</td></tr><tr><td>T</td><td>Set output to all port</td></tr><tr><td>0303</td><td>0303 (0000001100000011), Channel 0, 1, 8 and 9 are set ON other channels are set to OFF</td></tr><tr><td>User command:</td><td>#2FT010203(for ND-6058)</td></tr><tr><td>Response:</td><td></td></tr><tr><td>2F</td><td>Address ID</td></tr><tr><td>T</td><td>Set output to all port</td></tr><tr><td>01</td><td>Set channel 0 of port A ON</td></tr><tr><td>02</td><td>Set channel 1 of port B ON</td></tr><tr><td>03</td><td>Set channel 0 and 1 of port C ON</td></tr></table>

# 3.10 Digital Output (Continued)

( 6056, 6058 )

# @Description

Set digital output port channel value at specified address. This command is only available to modules involving the multiport digital output function.

# @Syntax

#(Addr)(Port)(OutData)&lt;CR&gt; (6056, 6058 only)

<table><tr><td>#</td><td>Command leading code. (1-character)</td></tr><tr><td>(Addr)</td><td>Address ID (2-character)</td></tr><tr><td></td><td>Set value to individual port</td></tr><tr><td></td><td>0H: for 6056 channel 14 to 8</td></tr><tr><td></td><td>0L: for 6056 channel 7 to 0</td></tr><tr><td>(Port)</td><td>0A: for 6058 port A</td></tr><tr><td></td><td>0B: for 6058 port B</td></tr><tr><td></td><td>0C: for 6058 port C (2-character)</td></tr><tr><td>(OutData)</td><td>Each bit is mapping to each channel number (2-character)</td></tr></table>

\* if the port of ND-6058 is in input mode, output data to this port will be ignore.

# @Response

&lt;CR&gt;

or

?(Addr)&lt;CR&gt;

> Command is valid.

? Command is invalid.

(Addr) Address ID.

# @Example

<table><tr><td>User command:</td><td>#30H03(for ND-6056)</td></tr><tr><td>Response:</td><td></td></tr></table>

30 Address ID

0H Set output to high byte

03 03 (00000011), Channel 8 and 9 are set ON other

03 channels are set to OFF

User command: #2F0A10&lt;CR&gt;

Response: &lt;CR&gt;

2F Address ID

0A Set output to port A

10 Set channel 4 of port A ON

# 3.11 Digital Output (Continued)

( 6056, 6058 )

# @Description

Set direct digital output channel value at specified address. This command is only available to modules involving the multiport digital output function.

# @Syntax

#(Addr)(Port)(ChNo)(OutData)&lt;CR&gt; (6056,6058 only)

```txt
# Command leading code. (1-character)
(Addr) Address ID (2-character)
Set direct channel value to individual port
H: for 6056 channel 14 to 8
L: for 6056 channel 7 to 0
A: for 6058 port A
B: for 6058 port B
C: for 6058 port C (1-character)
(ChNo) Channel value 7 ~ 0
1: ON
(OutData) 0: OFF
(1-character)
```

\* if the port of ND-6058 is in input mode, output data to this port will be ignore.

# @Response

```txt
&lt;CR&gt;
or
?(Addr)&lt;CR&gt;
> Command is valid
? Command is invalid.
(Addr) Address ID.
```

# @Example

<table><tr><td>User command:</td><td>#30H31(for ND-6056)</td></tr><tr><td>Response:</td><td></td></tr><tr><td>30</td><td>Address ID</td></tr><tr><td>H</td><td>Set output to high byte</td></tr><tr><td>3</td><td>Channel number is 3, that is channel 11</td></tr><tr><td>1</td><td>Set corresponding channel to ON</td></tr><tr><td>User command:</td><td>#2FA20</td></tr><tr><td>Response:</td><td></td></tr><tr><td>2F</td><td>Address ID</td></tr><tr><td>A</td><td>Set output to port A</td></tr><tr><td>2</td><td>Channel number is 2</td></tr><tr><td>0</td><td>Set corresponding channel to OFF</td></tr></table>

# 3.12 Synchronized Sampling

( 6050, 6052, 6053, 6054,6058, 6060, )

# @Description

Synchronized all modules to sample input values and stored the values in the module’s register at the same time and use “Read Synchronized Data” command to read the data and process it one by one.

For digital I/O module, this command is only available to modules involving the digital input function, such as NuDAM-6050, NuDAM-6052, NuDAM-6053, NuDAM-6054, NuDAM-6058 and NuDAM-6060.

# @Syntax

#\*\*&lt;CR&gt;

\#

\*\*

Command leading code.

Synchronized sampling command

# @Response

Note : Synchronized sampling command has NO response.

# @Example

User command: #\*\*&lt;CR&gt;

Synchronized sampling command has no response.

# 3.13 Read Synchronized Data

( 6050, 6052, 6053,6054, 6058, 6060 )

# @Description

After a synchronized sampling command #\*\* was issued, you can read the input value that was stored in the addressed module’s register and use same method to process other module‘s data one by one.

# @Syntax

```txt
$(Addr)4&lt;CR&gt;
```

\$ Command leading code.

Address ID.

4 Read synchronized data.

# @Response

ND-6050 module response :

```txt
!(Status)(DataOut)(DataIn)00&lt;CR&gt;
```

ND-6052 module response :

```asp
!(Status)(DataIn)0000&lt;CR&gt;
```

ND-6053 module response :

```asp
!(Status)(DataInH)(DataInL)00&lt;CR&gt;
```

ND-6054 module response :

```asp
!(Status)(DataInH)(DataInL)00&lt;CR&gt;
```

ND-6058 module response :

```asp
!(Status)(IOFlag)(DIn)(DataInA)(DataInB)(DataInC)&lt;CR&gt;
```

ND-6060 module response :

```txt
!(Status)(DataOut)(DataIn)00&lt;CR&gt;
```

or

```txt
?(Addr)&lt;CR&gt;
```

! Command is valid.

? Command is invalid.

<table><tr><td>(Status)</td><td>0 : Data has been sent at least once before.1 : Data has been sent for the first time since a synchronized sampling command was issued.(1-character)</td></tr><tr><td>(IOFlag)</td><td>Status of programmable I/O0x00: A(O/P) B(O/P) CH(O/P) CL(O/P)0x01: A(O/P) B(O/P) CH(O/P) CL(I/P)0x02: A(O/P) B(O/P) CH(I/P) CL(O/P)0x03: A(O/P) B(O/P) CH(I/P) CL(I/P)0x04: A(O/P) B(I/P) CH(O/P) CL(O/P)0x05: A(O/P) B(I/P) CH(O/P) CL(I/P)0x06: A(O/P) B(I/P) CH(I/P) CL(O/P)0x07: A(O/P) B(I/P) CH(I/P) CL(I/P)0x08: A(I/P) B(O/P) CH(O/P) CL(O/P)0x09: A(I/P) B(O/P) CH(O/P) CL(I/P)0x0A: A(I/P) B(O/P) CH(I/P) CL(O/P)0x0B: A(I/P) B(O/P) CH(I/P) CL(I/P)0x0C: A(I/P) B(I/P) CH(O/P) CL(O/P)0x0D: A(I/P) B(I/P) CH(O/P) CL(I/P)0x0E: A(I/P) B(I/P) CH(I/P) CL(O/P)0x0F: A(I/P) B(I/P) CH(I/P) CL(I/P)*I/P input mode, O/P output mode.</td></tr><tr><td>(DataOut)(DataIn)</td><td>Value of digital output channel. (2-character)Value of digital input channel. (2-character)</td></tr><tr><td>(DIn)</td><td>Value of dedicated digital input channel 3-0 for ND-6058. The first character is 0 (2-character)</td></tr><tr><td>(DataInH)(DataInL)(DataInA)(DataInB)(DataInC)</td><td>Value of digital input channel 15-8 (2-character)Value of digital input channel 7-0 (2-character)Value of port A channel 7-0 (2-character)Value of port B channel 7-0 (2-character)Value of port C channel 7-0 (2-character)</td></tr></table>

Example for NuDAM-6050 :

<table><tr><td>User command:</td><td>$304</td></tr><tr><td>Response:</td><td>!1065200</td></tr><tr><td>!</td><td>Command is valid.</td></tr><tr><td>1</td><td>Data has not been sent before.</td></tr><tr><td>06</td><td>06 (00000110) means digital output channel 1,2 are ON, channel 0,3,4,5,6,7 are OFF.</td></tr><tr><td>52</td><td>52(01010010) means digital input channel 1,4, 6 are HIGH, channel 0,2,3,5,7 are LOW..</td></tr></table>

Example for NuDAM-6058 :

<table><tr><td>User command:</td><td>$304</td></tr><tr><td>Response:</td><td>!10C0F010203</td></tr><tr><td>!</td><td>Command is valid.</td></tr><tr><td>1</td><td>Data has not been sent before.</td></tr><tr><td>0C</td><td>Port A and B are input mode, high and low half byte of port C are output mode.</td></tr><tr><td>0F</td><td>Channel 0,1,2,3 of digital input is HIGH.</td></tr><tr><td>01</td><td>01 (00000001) means port A digital input channel0 is HIGH, others are LOW.</td></tr><tr><td>02</td><td>02 (00000010) means port B digital input channel1 is HIGH, others are LOW.</td></tr><tr><td>03</td><td>03 (00000011) mean port C digital output channel 0,1 are ON, others are OFF.</td></tr></table>

# 3.14 Digital Input

( 6050, 6052, 6053, 6054, 6058, 6060 )

# @Description

Read the digital input channel value and readback the digital output channel value.

# @Syntax

```txt
$(Addr)6&lt;CR&gt;
$ Command leading code.
(Addr) Address ID
6 Digital data input command.
```

# @Response

ND-6050 module response :

```txt
!(DataOut)(DataIn)00&lt;CR&gt;
```

ND-6052 module response :

```asp
!(DataIn)0000&lt;CR&gt;
```

ND-6053 module response :

```txt
!(DataInH)(DataInL)00&lt;CR&gt;
```

ND-6054 module response :

```txt
!(DataInH)(DataInL)00&lt;CR&gt;
```

ND-6056 module response :

```txt
!(DataOutH)(DataOutL)00&lt;CR&gt;
```

ND-6058 module response :

```asp
!(loFlag)(DataIn)(DataA)(DataB)(DataC)&lt;CR&gt;
```

ND-6060 module response :

```txt
!(DataOut)(DataIn)00&lt;CR&gt;
```

ND-6063 module response :

```txt
!(DataOutH)0000&lt;CR&gt;
```

or ?(Addr)&lt;CR&gt;

<table><tr><td>!</td><td>Command is valid.</td></tr><tr><td>?</td><td>Command is invalid.</td></tr><tr><td>(DataOut)</td><td>Value of digital output channel. (2-character)</td></tr><tr><td>(DataIn)</td><td>Value of digital input. (2-character)</td></tr><tr><td>(DataInH)</td><td>Value of digital input channel 15-8. (2-character)</td></tr><tr><td>(DataInL)</td><td>Value of digital input channel 7-0.(2-character)</td></tr><tr><td>(DataOutH)</td><td>Value of digital output channel 15-8. (2-character)</td></tr><tr><td>(DataOutL)</td><td>Value of digital output channel 7-0.(2-character)</td></tr><tr><td>(DataA)</td><td>Value of digital channel 7-0.(2-character)</td></tr><tr><td>(DataB)</td><td>Value of digital channel 7-0.(2-character)</td></tr><tr><td>(DataB)</td><td>Value of digital channel 7-0.(2-character)</td></tr></table>

<table><tr><td rowspan="9"></td><td>Status of programmable I/O</td></tr><tr><td>0x00: A(O/P) B(O/P) CH(O/P) CL(O/P)</td></tr><tr><td>0x01: A(O/P) B(O/P) CH(O/P) CL(I/P)</td></tr><tr><td>0x02: A(O/P) B(O/P) CH(I/P) CL(O/P)</td></tr><tr><td>0x03: A(O/P) B(O/P) CH(I/P) CL(I/P)</td></tr><tr><td>0x04: A(O/P) B(I/P) CH(O/P) CL(O/P)</td></tr><tr><td>0x05: A(O/P) B(I/P) CH(O/P) CL(I/P)</td></tr><tr><td>0x06: A(O/P) B(I/P) CH(I/P) CL(O/P)</td></tr><tr><td>0x07: A(O/P) B(I/P) CH(I/P) CL(I/P)</td></tr><tr><td rowspan="9">(IOFlag)</td><td>0x08: A(I/P) B(O/P) CH(O/P) CL(O/P)</td></tr><tr><td>0x09: A(I/P) B(O/P) CH(O/P) CL(I/P)</td></tr><tr><td>0x0A: A(I/P) B(O/P) CH(I/P) CL(O/P)</td></tr><tr><td>0x0B: A(I/P) B(O/P) CH(I/P) CL(I/P)</td></tr><tr><td>0x0C: A(I/P) B(I/P) CH(O/P) CL(O/P)</td></tr><tr><td>0x0D: A(I/P) B(I/P) CH(O/P) CL(I/P)</td></tr><tr><td>0x0E: A(I/P) B(I/P) CH(I/P) CL(O/P)</td></tr><tr><td>0x0F: A(I/P) B(I/P) CH(I/P) CL(I/P)</td></tr><tr><td>*I/P input mode, O/P output mode.</td></tr></table>

# @Example

Example for NuDAM-6050 :

<table><tr><td>User command:</td><td>$306</td></tr><tr><td>Response:</td><td>!321100</td></tr><tr><td>!</td><td>Command is valid.</td></tr><tr><td>32</td><td>32 (00110010) means digital output channel 1,4,5 are ON, channel 0, 2, 3, 6, 7 are OFF.</td></tr><tr><td>11</td><td>11 (00000011) means digital input channel 0, 1are HIGH and channel 2, 3, 4, 5, 6, 7 are LOW.</td></tr><tr><td>00</td><td>No used</td></tr></table>

Example for NuDAM-6058 :

<table><tr><td>User command:</td><td>$304</td></tr><tr><td>Response:</td><td>!0C0F010203</td></tr><tr><td>!</td><td>Command is valid.</td></tr><tr><td>0C</td><td>Port A and B are input mode, high and low half byte of port C are output mode.</td></tr><tr><td>0F</td><td>Channel 0,1,2,3 of digital input is HIGH.</td></tr><tr><td>01</td><td>01 (00000001) means port A digital input channel 0 is HIGH, others are LOW.</td></tr><tr><td>02</td><td>02 (00000010) means port B digital input channel 1 is HIGH, others are LOW.</td></tr><tr><td>03</td><td>03 (00000011) mean port C digital output channel 0,1 are ON, others are OFF.</td></tr></table>

# 3.14 Programmable I/O Mode Setting

( 6058)

# @Description

Set the programmable input or output mode for ND-6058.

# @Syntax

```txt
$(Addr)S(IOFlag)&lt;CR&gt; (6058 only)
```

\$ Command leading code.

(Addr) Address ID

S Set programmable I/O mode

<table><tr><td rowspan="9"></td><td>Status of programmable I/O</td></tr><tr><td>0x00: A(O/P) B(O/P) CH(O/P) CL(O/P)</td></tr><tr><td>0x01: A(O/P) B(O/P) CH(O/P) CL(I/P)</td></tr><tr><td>0x02: A(O/P) B(O/P) CH(I/P) CL(O/P)</td></tr><tr><td>0x03: A(O/P) B(O/P) CH(I/P) CL(I/P)</td></tr><tr><td>0x04: A(O/P) B(I/P) CH(O/P) CL(O/P)</td></tr><tr><td>0x05: A(O/P) B(I/P) CH(O/P) CL(I/P)</td></tr><tr><td>0x06: A(O/P) B(I/P) CH(I/P) CL(O/P)</td></tr><tr><td>0x07: A(O/P) B(I/P) CH(I/P) CL(I/P)</td></tr><tr><td rowspan="9">(IOFlag)</td><td>0x08: A(I/P) B(O/P) CH(O/P) CL(O/P)</td></tr><tr><td>0x09: A(I/P) B(O/P) CH(O/P) CL(I/P)</td></tr><tr><td>0x0A: A(I/P) B(O/P) CH(I/P) CL(O/P)</td></tr><tr><td>0x0B: A(I/P) B(O/P) CH(I/P) CL(I/P)</td></tr><tr><td>0x0C: A(I/P) B(I/P) CH(O/P) CL(O/P)</td></tr><tr><td>0x0D: A(I/P) B(I/P) CH(O/P) CL(I/P)</td></tr><tr><td>0x0E: A(I/P) B(I/P) CH(I/P) CL(O/P)</td></tr><tr><td>0x0F: A(I/P) B(I/P) CH(I/P) CL(I/P)</td></tr><tr><td>*I/P input mode, O/P output mode.</td></tr></table>

# @Response

```asp
!(Addr)&lt;CR&gt;
```

or

```txt
?(Addr)&lt;CR&gt;
```

! Command is valid.

? Command is invalid.

Address ID

# @Example

User command: \$060C&lt;CR&gt;

Response: !06&lt;CR&gt;

! Command is valid.

0C Port A and B are input mode, high and low half byte of port C are output mode.

# 3.15 Read Leading Code Setting

( 6050, 6052, 6053, 6054,

6056, 6058, 6060, 6063 )

# @Description

Read command leading code setting and host watchdog status.

# @Syntax

\~(Addr)0&lt;CR&gt;

Command leading code.

(Addr) Address ID

0 Read command leading code setting.

# @Response

!(Addr)(Status)(C1)(C2)(C3)(C4)(C5)(C6)&lt;CR&gt;

or

?(Addr)&lt;CR&gt;

! Command is valid.

? Command is invalid.

Address ID

(2-character)

Bit 0 : Reserved

(Status) Bit 1 : Power failure or watchdog failure

Bit 2 : Host watchdog is enable

Bit 3 : Host failure

Leading code 1, for read configuration status,

(C1) firmware version, etc. default is \$.

(1-character)

(C2) Leading code 2, for read synchronize sampling,digital output ,default is #. (1-character)

(C3) Leading code 3, for change configuration.

default is %. (1-character)

(C4) Leading code 4, for read alarm status, enablealarm, etc. default is @. (1-character)

Leading code 5, for read command leading code,

(C5) change command leading code, etc. default is \~.

(1-character)

(C6) Leading code 6, this leading code is reserved.

Default is \*. (1-character)

# @Example

```txt
User command: ~060&lt;CR&gt;
Response: !0600$#%@~*&lt;CR&gt;
```

Command leading code setting is \$#%@\~\* for module address ID is 06, current status is factory default setting.

# 3.16 Change Leading Code Setting

( 6050, 6052, 6053, 6054,

6056, 6058, 6060, 6063 )

# @Description

User can use this command to change command leading code setting as he desired.

# @Syntax

\~(Addr)10(C1)(C2)(C3)(C4)(C5)(C6)&lt;CR&gt;

<table><tr><td>~</td><td>Command leading code.</td></tr><tr><td>(Addr)</td><td>Address ID, range (00 - FF).</td></tr><tr><td>10</td><td>Change command leading code setting.</td></tr><tr><td></td><td rowspan="2">Leading code 1, for read configuration status, firmware version, etc. default is $. (1-character)</td></tr><tr><td>(C1)</td></tr><tr><td>(C2)</td><td>Leading code 2, for read synchronize sampling, digital output ,default is #. (1-character)</td></tr><tr><td>(C3)</td><td>Leading code 3, for change configuration. default is %. (1-character)</td></tr><tr><td>(C4)</td><td>Leading code 4, for read alarm status, enable alarm, etc. default is @. (1-character)</td></tr><tr><td>(C5)</td><td>Leading code 5, for read command leading code, change leading code, etc. default is ~. (1-character)</td></tr><tr><td>(C6)</td><td>Leading code 6, this leading code is reserved. default is *. (1-character)</td></tr></table>

# @Response

<table><tr><td colspan="2">!(Addr)&lt; CR&gt;</td></tr><tr><td colspan="2">or</td></tr><tr><td colspan="2">?(Addr)&lt;CR&gt;</td></tr><tr><td>!</td><td>Command is valid.</td></tr><tr><td>?</td><td>Command is invalid.</td></tr><tr><td>(Addr)</td><td>Address ID.</td></tr></table>

# @Examples

```txt
User command: ~060&lt;CR&gt;
Response: !0600$#%@~*&lt;CR&gt;
User command: ~0610A#%@~*&lt;CR&gt;
Response: !06&lt;CR&gt;
User command: A06F
Response: !06A1.8&lt;CR&gt;
```

Read leading code setting is \$#%@\~\* for module address 06 and change leading code \$ to A, then use A06F to read firmware version of module on address 06.

# \*\*\* WARNING \*\*\*

We do not recommend users to change the default setting of leading code, because it will make you confuse

The leading code change only use the command conflicts other devices on the network.

# 3.17 Set Host Watchdog Timer & Safety Value

( 6050, 6052, 6053, 6054,

6056, 6058, 6060, 6063 )

# @Description

Set host watchdog timer, module will change to safety state when host is failure. Define the output value in this command.

# @Syntax

\~(Addr)2(Flag)(TimeOut)(SafeValue)&lt;CR&gt;

\~(Addr)2(Flag)(TimeOut)(SafeH)(SafeL)&lt;CR&gt; (6056 only)

\~(Addr)2(Flag)(TimeOut)(SafeA)(SafeB)(SafeC)&lt;CR&gt; (6058only)

<table><tr><td>~</td><td>Command leading code.</td></tr><tr><td>(Addr)</td><td>Address ID, range (00 - FF).</td></tr><tr><td>2</td><td>Set host watchdog timer and safe state value.</td></tr><tr><td>(Flag)</td><td>0 : Disable host watchdog timer1 : Enable host watchdog timer (1-character)</td></tr><tr><td></td><td>Host timeout value, between this time periodhost must send (Host is OK) command tomodule, otherwise module will change to safetystate.</td></tr><tr><td>(TimeOut)</td><td>Range 01 - FF. (2-character)One unit is 100 ms01 = 1 * 100 = 100 msFF = 255 * 100 = 25.5 sec</td></tr><tr><td>(SafeValue)</td><td>8 channels safety value of digital outputchannels when host is failure. (2-character)</td></tr><tr><td>(SafeH)</td><td>Safety value of digital output channels 14 ~ 8when host is failure. (2-character)</td></tr><tr><td>(SafeL)</td><td>Safety value of digital output channels 7 ~ 0when host is failure. (2-character)</td></tr><tr><td>(SafeA)</td><td>Safety value of port A channels 7 ~ 0 when hostis failure while A in output mode. (2-character)</td></tr><tr><td>(SafeB)</td><td>Safety value of port B channels 7 ~ 0 when hostis failure while B in output mode. (2-character)</td></tr><tr><td>(SafeC)</td><td>Safety value of port C channels 7 ~ 0 when hostis failure while C in output mode. (2-character)</td></tr></table>

@Response
```c
!(Addr)&lt;CR&gt;
or
?(Addr)&lt;CR&gt;
!
? (Addr)
Command is valid.
Command is invalid.
Address ID
```

# @Example

Example for NuDAM-6050 :

<table><tr><td>User command:</td><td>~0621121C</td></tr><tr><td>Response:</td><td>!06</td></tr><tr><td>06</td><td>Address ID</td></tr><tr><td>2</td><td>Set host watchdog timer and safe state value.</td></tr><tr><td>1</td><td>Enable host watchdog timer.</td></tr><tr><td>12</td><td>Timeout value. 0x12 = 1818 * 100 = 1800 ms</td></tr><tr><td>1C</td><td>1C (00011100) Digital output channel DO2, DO3 and DO4 are high, the others are low.</td></tr></table>

Example for NuDAM-6056 :

<table><tr><td>User command:</td><td>~0621121C1C</td></tr><tr><td>Response:</td><td>!06</td></tr><tr><td>06</td><td>Address ID</td></tr><tr><td>2</td><td>Set host watchdog timer and safe state value.</td></tr><tr><td>1</td><td>Enable host watchdog timer.</td></tr><tr><td></td><td>Timeout value. 0x12 = 18</td></tr><tr><td>12</td><td>18 * 53.3 = 959 ms</td></tr><tr><td></td><td>18 * 100 = 1800 ms</td></tr><tr><td>1C1C</td><td>1C1C (0001110000011100) Digital output channel DO2, DO3, DO4, DO10, DO11, DO12 are high, the others are low.</td></tr></table>

Example for NuDAM-6058 :

<table><tr><td>User command:</td><td>~0621121C1C1C</td></tr><tr><td>Response:</td><td>!06</td></tr><tr><td>06</td><td>Address ID</td></tr><tr><td>2</td><td>Set host watchdog timer and safe state value.</td></tr><tr><td>1</td><td>Enable host watchdog timer.</td></tr><tr><td>12</td><td>Timeout value. 0x12 = 1818 * 100 = 1800 ms</td></tr><tr><td>1C1C1C</td><td>1C (00011100) port A, B and C channel 2, 3 and4 are high, the other are low.</td></tr></table>

# 3.18 Read Host Watchdog Timer & Safety Value

( 6050, 6052, 6053, 6054,

6056, 6058, 6060, 6063 )

# @Description

Read host watchdog timer setting and the safety value.

# @Syntax

```txt
~(Addr)3&lt;CR&gt;
~ Command leading code.
(Addr) Address ID
3 Read host watchdog setting and module safety state value.
```

# @Response

```fortran
!(Addr)(Flag)(TimeOut)(SafeValue)&lt;CR&gt;
!(Addr)(Flag)(TimeOut)(SafeH)(SafeL)&lt;CR&gt; (6056 only)
!(Addr)(Flag)(TimeOut)(SafeA)(SafeB)(SafeC)&lt;CR&gt; (6058only)
or
?(Addr)&lt;CR&gt;
!
(Addr)
(Flag)
(TimeOut)
(SafeValue)
Command is valid.
Command is invalid.
Address ID, range (00 - FF).
0 : Host watchdog timer is disable
1 : Host watchdog timer is enable(1-character)
Host timeout value.
Range 01 - FF. (2-character)
One unit is 100 ms
01 = 1 * 100 = 100 ms
FF = 255 * 100 = 25.5 sec
8 channels safety state digital output value when host is failure. (2-character)
```

# @Example

<table><tr><td>User command:</td><td>~063</td></tr><tr><td>Response:</td><td>!061121C</td></tr></table>

<table><tr><td>06</td><td>Address ID</td></tr><tr><td>1</td><td>Host watchdog timer is enable.</td></tr><tr><td>12</td><td>Timeout value. 0x12 = 18</td></tr><tr><td></td><td>18 * 100 = 1800 ms</td></tr><tr><td>1C</td><td>1C (00011100) Digital output channel DO3, DO4 and DO5 are high, the others are low.</td></tr></table>

Between 1800 ms time period, if host does not send (Host is OK) then digital output will change to safety state 1C ( 00011100) means digital output DO3 , DO4 and DO5 is high, others are low.

# 3.19 Change Polarity

# @Description

To change the polarity state of digital inputs and outputs of the module.

# @Syntax

\~(Addr)CP(State)&lt;CR&gt;
```txt
~ Command leading code (1 character)
(Addr) Address ID (2 characters)
CP Change Polarity (2 characters)
Polarity state of digital inputs and outputs (2characters)
00 : Do not change polarity
(State) 01 : Change the polarity of digital inputs
02 : Change the polarity of digital outputs
03 : Change the polarity both the digital inputs and outputs
```

@Response
```txt
!(Addr)&lt;CR&gt;
or
?(Addr)&lt;CR&gt;
! Command is valid.
? Command is invalid.
(Addr) Address ID.
```

# @Example

```txt
User command: ~06CP01&lt;CR&gt;
Response: !06&lt;CR&gt;
```

To change the polarity of digital inputs of the DI/O module which ID is 06H.

Note : For this command ,you could define the logic level which you want, For example, if the input connect to high level signal ,and you want to read back the input as a “0”,then you could change the polarity to fit your requirement .

# 3.20 Read Polarity

# @Description

To read the polarity state of digital inputs and outputs of the module.

# @Syntax

```lisp
~(Addr)CR&lt;CR&gt;
~ Command leading code (1 character)
(Addr) Address ID (2 character)
CR Read Polarity (2 character)
```

# @Response

```txt
!(Addr)(State)&lt;CR&gt;
or
```

?(Addr)&lt;CR&gt;
```txt
! Command is valid.
? Command is invalid.
(Addr) Address ID.
```

```txt
(Polarity state of digital inputs and outputs
00 : Polarity were not changed
01 : Change the polarity of digital inputs
02 : Change the polarity of digital outputs
03 : Change the polarity both the digital inputs and outputs
```

# @Example

```txt
User command: ~03CR&lt;CR&gt;
Response: !0602&lt;CR&gt;
```

Read the polarity of the DI/O module which ID is 03H.

# 3.21 Host is OK

# @Description

When host watchdog timer is enable, host computer must send this command to every module before timeout otherwise “host watchdog timer enable” module‘s output value will go to safety state output value.

Timeout value and safety state output value is defined in 3.14. “Set Host Watchdog Timer & Safety Value”.

@Syntax
```txt
~**&lt;CR&gt;
    ~ Command leading code.
    ** Host is OK.
```
@Response

Note : Host is OK command has NO response.

@Example

User command: \~\*\*&lt;CR&gt;

# Warranty Policy

Thank you for choosing ADLINK. To understand your rights and enjoy all the after-sales services we offer, please read the following carefully.

1. Before using ADLINK’s products please read the user manual and follow the instructions exactly. When sending in damaged products for repair, please attach an RMA application form which can be downloaded from: http://rma.adlinktech.com/policy/.

2. All ADLINK products come with a limited two-year warranty, one year for products bought in China.

The warranty period starts on the day the product is shipped from ADLINK’s factory.
Peripherals and third-party products not manufactured by ADLINK will be covered by the original manufacturers' warranty.
For products containing storage devices (hard drives, flash cards, etc.), please back up your data before sending them for repair. ADLINK is not responsible for any loss of data.
Please ensure the use of properly licensed software with our systems. ADLINK does not condone the use of pirated software and will not service systems using such software. ADLINK will not be held legally responsible for products shipped with unlicensed software installed by the user.
For general repairs, please do not include peripheral accessories. If peripherals need to be included, be certain to specify which items you sent on the RMA Request & Confirmation Form. ADLINK is not responsible for items not listed on the RMA Request & Confirmation Form.

3. Our repair service is not covered by ADLINK's guarantee in the following situations:

Damage caused by not following instructions in the User's Manual.
Damage caused by carelessness on the user's part during product transportation.
Damage caused by fire, earthquakes, floods, lightening, pollution, other acts of God, and/or incorrect usage of voltage transformers.
Damage caused by inappropriate storage environments such as with high temperatures, high humidity, or volatile chemicals.

Damage caused by leakage of battery fluid during or after change of batteries by customer/user.
Damage from improper repair by unauthorized ADLINK technicians.
Products with altered and/or damaged serial numbers are not entitled to our service.
This warranty is not transferable or extendible.
Other categories not protected under our warranty.

4. Customers are responsible for all fees necessary to transport damaged products to ADLINK.

For further questions, please e-mail our FAE staff: service@adlinktech.com
[🔗 Link to the original document](.nd-6058-manual-2/nd-6058-manual-2.pdf)