NuPRO-795
ETX PICMG 1.0

Half-Size SBC

User’s Manual

Manual Rev.

2.00

Revision Date:  October 22, 2004

Part No:

50-13047-100

Advance Technologies; Automate the World.

Copyright 2004 ADLINK TECHNOLOGY INC.

All Rights Reserved.

The information in this document is subject to change without prior
notice in order to improve reliability, design, and function and does
not represent a commitment on the part of the manufacturer.

In no event will the manufacturer be liable for direct, indirect, spe-
cial, incidental, or consequential damages arising out of the use or
inability  to  use  the  product  or  documentation,  even  if  advised  of
the possibility of such damages.

This document contains proprietary information protected by copy-
right. All rights are reserved. No part of this manual may be repro-
duced by any mechanical, electronic, or other means in any form
without prior written permission of the manufacturer.

Trademarks

Product  names  mentioned  herein  are  used  for  identification  pur-
poses only and may be trademarks and/or registered trademarks
of their respective companies.

Getting Service from ADLINK
Customer  Satisfaction  is  top  priority  for  ADLINK  Technology  Inc.
Please contact us should you require any service or assistance.

ADLINK TECHNOLOGY INC.

Web Site:

http://www.adlinktech.com

Sales & Service:

Service@adlinktech.com

TEL:

FAX:

+886-2-82265877

+886-2-82265717

Address:

9F, No. 166, Jian Yi Road, Chungho City,

Taipei, 235 Taiwan

Please email or FAX this completed service form for prompt and
satisfactory service.

Company Information

Company/Organization

Contact Person

E-mail Address

Address

Country

TEL

Web Site

Product Model

Environment

FAX:

Product Information

OS:
M/B:                             CPU:
Chipset:                       Bios:

Please give a detailed description of the problem(s):

Table of Contents

List of Figures ........................................................................  iii

1 Introduction ........................................................................  1
Product Overview ................................................................  1
Unpacking Checklist ............................................................  1
Specifications.......................................................................  2
NuPRO-795 Mechanical Drawing........................................  4
ETX-EV133 Functional Diagrams........................................  5

1.1
1.2
1.3
1.4
1.5

2.1

2 Connectors and Jumpers ..................................................  7
Connector Pin Assignments ................................................  7
VGA Connector (CN10)  .................................................. 7
USB Connector (CN17, CN22)  ....................................... 7
Keyboard and Mouse (CN11)  ......................................... 8
COM Pin Header (CN15, CN16) ..................................... 8
Parallel Port (CN1) .......................................................... 9
IDE (CN4, CN6)  ............................................................ 10
USB Pin (CN3, CN24)  .................................................. 11
Serial ATA Connectors (CN5, CN7, CN9, CN14)  ......... 11
X4 Extension Pin Header (CN8)  ................................... 12
TV-Out Pin Header (CN12) ........................................... 12
LDVS Connector (CN19, CN21)  ................................... 13
IrDA Connector (CN13)  ................................................ 13
Miscellaneous Connector (CN18)] ................................ 14
Fan Connector (CN20)  ................................................. 14
Audio-Out Pin Header (CN26)  ...................................... 14
Compact Flash Type I/II Connector (CN28)  ................. 15
ATX Power Connector (CN29)  ..................................... 16
ETX X1 Connector (PCI Bus, USB, Audio) ................... 17
ETX X2 Connector (ISA Bus)  ....................................... 18
ETX X3 Connector ........................................................ 19
ETX X4 Connector ........................................................ 20
Jumper Settings.................................................................  21
CF Mode Selection (JP2) .............................................. 21
Panel Power Selection (JP3)  ........................................ 21

2.2

Table of Contents

 i

3 System Resources............................................................ 23
Interrupt Assignments ........................................................  23
3.1
PCI Bus Arbitration Assignment.........................................  24
3.2
3.3
PCI Interrupt Routing .........................................................  24
3.4 Memory Map ......................................................................  25
Direct Memory Access Channels.......................................  25
3.5
I/O Address Map ................................................................  26
3.6
System Management Bus (I2C).........................................  27
3.7

4 Phoenix Award BIOS ........................................................ 29
Description .........................................................................  29
4.1
4.2 Main Menu .........................................................................  29
Standard CMOS Features .................................................  31
4.3
IDE Primary and Secondary Master/Slave Items  ......... 33
4.4
Advanced BIOS Features ..................................................  34
4.5
Advanced Chipset Features...............................................  37
4.6
Integrated Peripherals........................................................  40
4.7
Power Management Setup ................................................  42
4.8
PnP/PCI Configuration.......................................................  46
PC Health Status ...............................................................  47
4.9
4.10 BIOS POST Codes ............................................................  48

5 Driver Installation.............................................................. 55
VIA Hyperion 4in1 Drivers..................................................  55
VGA Driver.........................................................................  57
Realtek RTL8139CL+ Ethernet Controller .........................  57
Audio Driver .......................................................................  58

5.1
5.2
5.3
5.4

6 Watchdog Timer................................................................ 61
Programming Examples: .................................................... 61

Warranty Policy ..................................................................... 63

ii

Table of Contents

List of Figures

Figure 1-1: ProCB-795 Carrier Board Layout ..............................  4
Figure 1-2: ETX-EV133 Functional Diagram ...............................  5
Figure 1-3: ETX-EV133 Board/Connector Layout........................  6
Figure 4-1: AWARD BIOS Main Menu.......................................  29
Figure 4-2: Standard CMOS Features Menu .............................  31
IDE Primary and Secondary Master/Slave Items Menu
Figure 4-3:
33

Figure 4-4: Advanced BIOS Features Menu..............................  34
Figure 4-5: Advanced Chipset Features Menu ..........................  37
 Integrated Peripherals Menu ..................................  40
Figure 4-6:
Figure 4-7:
 Integrated Peripherals Menu ..................................  42
Figure 4-8: PnP/PCI Configuration Menu ..................................  46

List of Figures

 iii

iv

List of Figures

1

Introduction

1.1 Product Overview

The NuPRO-795 ETX-based single board computer is comprised
of the ProCB-795, a PICMG 1.0 compliant half-size carrier board,
and the ETX-EV133 ETX module.

The  carrier  board  includes  common  PC  peripheral  I/O  interfaces
such as serial and parallel ports, keyboard/mouse, Ethernet, IDE,
VGA, and audio. It also includes an integrated debug port, hard-
ware monitor, GPIO, and audio power amplifier and is expandable
via the PCI bus.

The ETX-EV133 module is based on the VIA Eden ESP processor
and VIA Apollo PLE133T and VT82C686B chipsets. The onboard
SODIMM  socket  supports  144-pin  SODIMM  type  memory  mod-
ules and accommodates non-ECC SDRAM modules up to 512MB.
The VIA Eden Processor is available from 400 MHz up to 1 GHz.

The VIA VT82C686B southbridge incorporates a PCI/ISA bridge,
a  VGA  AGP  controller,  an  EIDE  controller  supporting  both  PIO
and UDMA modes, USB ports v1.1, two serial ports, one parallel
port (SPP/ECP/EPP), one PS2 keyboard/mouse interface, AC ‘97
audio interface and power management functionality.

The ETX-EV133 also includes an integrated 10/100Base-T Ether-
net port, a watchdog timer,  and support for LVDS based flat panel
displays.

1.2 Unpacking Checklist

Check the shipping carton for any damage. If the shipping carton
and  contents  are  damaged,  notify  the  dealer  for  a  replacement.
Retain the shipping carton and packing materials for inspection by
the  dealer.  Obtain  authorization  before  returning  any  product  to
ADLINK.

Introduction

 1

Check the following items are included in the package, if there are
any items missing, please contact your dealer:

Included Items

All-in-one support CD-ROM (software & manuals)

NuPRO-795 carrier board with ETX-EV133 module

Printer and COM port cable bracket

ATA-100 cables (x2)

Note:

The  packaging  of  the  NuPRO-795  OEM  version  with
non-standard  configuration,  functionality,  or  package
may vary according to different configuration requests.

CAUTION:

The board fitted inside the NuPRO-795 system must be
protected  from  static  discharge  and  physical  shock.
Never  remove  any  of  the  socketed  parts  except  at  a
static-free workstation. Use the anti-static bag shipped
with  the  product  to  handle  the  board.  Wear  a  wrist
strap  grounded  through  one  of  the  system's  ESD
Ground jacks when servicing system components

1.3 Specifications

NuPRO-795 Specifications

Carrier Board

ProCB-795

CPU

VIA Eden ESP processor (eBGA package)

System Memory

144-pin SODIMM socket for up 512 MB PC100/133
non-ECC SDRAM

Chipset

VIA Apollo PLE133T with VT8601T northbridge and
VT82C686B southbridge

L2 Cache

64kB integrated in CPU

2

Introduction

NuPRO-795 Specifications

Integrated AGP2X Trident Blade 2D/3D Video
Accelerator (VT8601T)

Display

Up to 8MB UMA Video RAM

Up to UXGA 1600 x 1200 @ 32bpp CRT

Supports TFT on single channel LVDS (18-bit)

AWARD 2Mb Flash BIOS with ACPI and APM 1.2
power management with console redirection and
CMOS backup in onboard EEPROM

BIOS

USB

Two USB ports, USB 1.1 compliant

Ethernet

Realtek RTL8139CL+ chipset, 10BaseT/
100BaseTx, Wake-on LAN

Parallel Port

One high-speed parallel port, SPP/EPP/ECP mode

Serial Ports

Two high speed RS-232C ports (COM1/COM2)

Keyboard/Mouse One PS/2 keyboard and one PS/2 mouse

Floppy Interface Not implemented

IrDA

Audio

Supports SIR IrDA 1.1

Realtek ALC201A AC97 ver. 2.0

Watchdog Timer

128-level timer generates RESET or NMI

Dimension

122mm x 167.5mm

Power Supply

+5V, 10W typical

Operating Temp. 0 to 60ºC

Humidity

0 to 90% @ 55ºC

Dimensions

185.45mm x 123.12mm

Operating System Windows 2000, XP, Linux

 Vibration

Operating: 5-100Hz, 0.00142 g2/Hz; 100-500Hz
(cid:88)

 6dB/Octave; 0.5Grms, 3 axes,

30mins/axis

Non-operating: 5-100Hz, 0.02g2/Hz; 100-500Hz
 6dB/Octave; 1.88Grms, 3 axes,
(cid:88)

1hr/axis (IEC 68-2-64)

Introduction

 3

1.4 NuPRO-795 Mechanical Drawing

Figure 1-1: ProCB-795 Carrier Board Layout

4

Introduction

1.5 ETX-EV133 Functional Diagrams

C P U

V I A   E d e n   E S P
4 0 0 ,   6 0 0 ,   8 0 0

F S B
6 6 /1 0 0 /1 3 3

N o r t h b r i d g e
V I A   V T 8 6 0 1 T

S D R A M
M e m o r y
C o n tr o lle r

A G P
V G A
C o n tr o lle r

S D R A M
S O D I M M
S o c k e t

P C I B u s

D u a l c h a n n e l U S B  v 1 .1

1
X

S o u t h b r i d g e
V I A   V T 8 2 C 6 8 6 B

A T A 1 0 0

U S B  1 .1

R T C

A u d io

S u p e r  I/O

P C I to  IS A
B r id g e

R e a l t e k
A C '9 7   C o d e c
A L 2 0 1 A

W a t c h d o g
T i m e r

IS A  B u s

B I O S

2
X

4
X

3
X

A T A  1 0 0

R e a l t e k
E t h e r n e t
M a c / P H Y
R T 8 1 3 9 C L +

C R T

N S
L V D S   T r a n s m .
D S 9 0 C 3 6 3 A M T D

E E P R O M
C M O S
B a c k u p

I 2 C

K e y b o a r d

M o u s e

L P T 1

C O M 1

C O M 2

Figure 1-2: ETX-EV133 Functional Diagram

Introduction

 5

- VGA / LCD/ Video
- COM1 / COM2
- LPT1
- IrDA
- Mouse
- Keyboard

X3

- Ethernet
- IDE1 / IDE2
- Power Signals
- Speaker, Battery
- I2C & SMB  bus

X4

Eden ESP6000
(133X6.0)1.05V SET

- VGA / LCD/ Video
- COM1 / COM2
- LPT1
- IrDA
- Mouse
- Keyboard

VT82C686B
"Southbridge"

X3

"

N
o
r
t
h
b
r
i
d
g
e
"

V
T
8
6
0
1
T

X1

- 32-bit PCI bus
- USB
- Audio

X2

- ISA bus

Figure 1-3: ETX-EV133 Board/Connector Layout

6

Introduction

2 Connectors and Jumpers

This  chapter  will  familiarize  the  user  with  the  connectors  and
jumpers on the NuPRO-795.

2.1 Connector Pin Assignments

Detailed descriptions and pin-outs for each connector are given in
the following section. Please refer to

VGA Connector (CN10)

Signal Name Pin Pin Signal Name

Red

Blue

GND

GND

+5V

N.C.

HSYNC

1

3

5

7

9

11

13

2

4

6

8

10

12

14

Green

N.C.

GND

GND

GND

DDCDAT

VSYNC

DDCCLK

15 —

—

USB Connector (CN17, CN22)

PIN

SIGNAL

1

2

3

4

VCC

USB-

USB+

Ground

Connectors and Jumpers

 7

Keyboard and Mouse (CN11)

1

5

2

6

Pin

Signal Name

1

2

3

4

5

6

Keyboard Data

Keyboard Clock

Mouse Data

Mouse Clock

Power

Ground

COM Pin Header (CN15, CN16)

1

5

6

10

Pin

RS-232

1

2

3

4

5

6

7

8

9

DCD, Data carrier detect

RXD, Receive data

TXD, Transmit data

DTR, Data terminal ready

GND, ground

DSR, Data set ready

RTS, Request to send

CTS, Clear to send

RI, Ring indicator

8

Connectors and Jumpers

Parallel Port (CN1)

Signal Name

Pin Pin Signal Name

Line printer strobe

PD0, parallel data 0

PD1, parallel data 1

PD2, parallel data 2

PD3, parallel data 3

PD4, parallel data 4

PD5, parallel data 5

PD6, parallel data 6

PD7, parallel data 7

ACK, acknowledge

Busy

Paper empty

Select

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

AutoFeed

Error

Initialize

Select

Ground

Ground

Ground

Ground

Ground

Ground

Ground

Ground

N/A

N/A

Connectors and Jumpers

 9

IDE (CN4, CN6)

Signal Name

Pin

Pin

Signal Name

1

2

Reset IDE

IDE Data 7

IDE Data 6

IDE Data 5

IDE Data 4

IDE Data 3

IDE Data 2

IDE Data 1

IDE Data 0

Ground

DREQ0

IDEIOW#

IDEIOR#

IDEIORDY

DACK0#

IDEIRQ14

39

40

IDE Address 1

IDE Address 0

IDE Chip select 1#

IDE activity

1

3

5

7

9

11

13

15

17

19

21

23

25

27

29

31

33

35

37

39

2

4

6

8

10

12

14

16

18

20

22

24

26

28

30

32

34

36

38

40

GND

IDE Data 8

IDE Data 9

IDE Data 10

IDE Data 11

IDE Data 12

IDE Data 13

IDE Data 14

IDE Data 15

KEY

GND

GND

GND

CBSEL

GND

NC

PDIAG#

IDE Address 2

IDE Chip select 3#

GND

10

Connectors and Jumpers

USB Pin (CN3, CN24)

1

3

5

7

2

4

6

8

10

Pin

Signal Name

Signal Name

Pin

1

3

5

7

—

USB1_VCC

USB2_VCC

USB1-

USB1+

GND

—

USB2-

USB2+

GND

KEY

2

4

6

8

10

Serial ATA Connectors (CN5, CN7, CN9, CN14)

Pin

Signal Name

1

2

3

4

5

6

7

1

2

3

4

5

6

7

GND

Tx+

Tx-

GND

Rx-

Rx+

GND

Connectors and Jumpers

 11

X4 Extension Pin Header (CN8)

1

2

11

12

TV-Out Pin Header (CN12)

1

7

2

8

Pin

Signal Name

1

2

3

4

5

6

7

8

9

10

11

12

+5V

X4_GPE1J

X4_SMBLARTJ

X4_GPE2J

BATLOWJ

ROMKBCSJ

X4_RSMRSTJ

X4_EXTSMI

X1_SERIRQ

X4_GPCSJ

GND

X4_EXTPRG

Pin

Signal Name

1

2

3

4

5

6

7

8

Y

GND

C

GND

COMP

GND

SYNC

GND

12

Connectors and Jumpers

LDVS Connector (CN19, CN21)

Pin

Signal Name

Pin

Signal Name

1

2

3

4

5

6

7

8

9

10

Panel Power

Panel Power

GND

GND

Txout0#

Txout0

GND

Txout1#

Txout1

GND

11

12

13

14

15

16

17

18

19

20

Txout2#

Txout2

GND

Txclk#

Txclk

GND

Txout3#

Txout3

GND

Panel Detect

IrDA Connector (CN13)

1

5

Pin

Signal Name

1

2

3

4

5

+5V

No connect

IrRXD

Ground

IrTXD

Connectors and Jumpers

 13

Miscellaneous Connector (CN18)]

POWER LED

KEYBOARD LOCK

ATX POWER
CONN.

1

2

3

4

5

6

7

8

9

x

11

12

13

14

15

16

17

18

19

20

SPEAKER
(BUZZER)

RESET BOTTON

HDD LED

POWER BOTTON

 Signal Name

Pin

Pin

Signal Name

PW_LED+

NC

PW_LED-

KB_LOCK

GND

GND

NC

PS_ON

5VSB

PME#

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

BUZZER

NC

NC

+5V

PW_GD

GND

HDD_LED-

HDD_LED+

PW_BTN

GND

Fan Connector (CN20)

Pin

Signal Name

3

2

1

1

2

3

NC

+12V

GND

Audio-Out Pin Header (CN26)

1

5

2

6

Pin

Signal Name

1

2

3

4

5

6

MIC In

ASGND

Line In Left

Line In Right

Line Out Left

Line Out Right

14

Connectors and Jumpers

Compact Flash Type I/II Connector (CN28)

Signal Name

Pin

Pin

Signal Name

GND

SDD3

SDD4

SDD5

SDD6

SDD7

SDCS#1

GND

GND

GND

GND

GND

+5V

GND

GND

GND

GND

SDA2

SDA1

SDA0

SDD0

SDD1

SDD2

IOIS16#

GND

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

49

50

GND

SDD11

SDD12

SDD13

SDD14

SDD15

SDCS#3

GND

SDIOR#

SDIOW#

+5V

IDEIRQ15

+5V

PCSEL

NC

SIDERST#

SIORDY

NC

SDDACK#

IDEACT#

S66DECT

SDD8

SDD9

SDD10

GND

Connectors and Jumpers

 15

ATX Power Connector (CN29)

Pin

Signal

Pin

Signal

1

2

3

4

5

6

7

8

9

10

+3.3V

+3.3V

GND

+5V

GND

+5V

GND

PWRGOOD

STB5V

+12V

11

12

13

14

15

16

17

18

19

20

+3.3V

-12V

GND

PS_ON#

GND

GND

GND

-5V

+5V

+5V

16

Connectors and Jumpers

ETX X1 Connector (PCI Bus, USB, Audio)

Pin
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
61
63
65
67
69
71
73
75
77
79
81
83
85
87
89
91
93
95
97
99

Signal Name
GND
PCICLK3
GND
PCICLK1
REQ3#
GNT2#
REQ2#
REQ1#
GNT0#
VCC
SERIRQ
AD0
AD1
AD4
AD6
C/BE0#
AD8
GND
AD10
AD11
AD12
AD13
AD14
AD15
C/BE1#
VCC
PAR
PERR#
PME#
LOCK#
TRDY#
IRDY#
FRAME#
GND
AD16
AD17
AD19
AD20
AD22
AD23
AD24
VCC
AD25
AD28
AD27
AD30
PCIRST#
INTC#
INTA#
GND

Pin
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
62
64
66
68
70
72
74
76
78
80
82
84
86
88
90
92
94
96
98
100

Signal Name
GND
PCICLK4
GND
PCICLK2
GNT3#
3V3
GNT1#
3V3
RESERVED
VCC
REQ0#
3V3
AD2
AD3
AD5
AD7
AD9
GND
LINEIN_L
MICIN
LINEIN_R
AVCC
LINEOUT_L
AGND
LINEOUT_R
VCC
SERR#
RESERVED
USB2-
DEVSEL#
USB3-
STOP#
USB2+
GND
C/BE2#
USB3+
AD18
USB0-
AD21
USB1-
C/BE3#
VCC
AD26
USB0+
AD29
USB1+
AD31
INTD#
INTB#
GND

Connectors and Jumpers

 17

ETX X2 Connector (ISA Bus)

Pin
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
61
63
65
67
69
71
73
75
77
79
81
83
85
87
89
91
93
95
97
99

Signal Name
GND
SD14
SD13
SD12
SD11
SD10
SD9
SD8
MEMW#
MEMR#
LA17
LA18
LA19
LA20
LA21
LA22
LA23
GND
SBHE#
SA0
SA1
SA2
SA3
SA4
SA5
VCC
SA6
SA7
SA8
SA9
SA10
SA11
SA12
GND
SA13
SA14
SA15
SA16
SA18
SA19
IOCHRDY
VCC
SD0
SD2
SD3
DREQ2(2)
SD5
SD6
IOCHK#
GND

Pin
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
62
64
66
68
70
72
74
76
78
80
82
84
86
88
90
92
94
96
98
100

Signal Name
GND
SD15
MASTER#
DREQ7
DACK7#
DREQ6
DACK6#
DREQ5
DACK5#
DREQ0
DACK0#
IRQ14
IRQ15
IRQ12(1)
IRQ11
IRQ10
IO16#
GND
M16#
OSC
BALE
TC
DACK2#(2)
IRQ3
IRQ4
VCC
IRQ5
IRQ6
IRQ7
SYSCLK
REFSH#
DREQ1
DACK1#
GND
DREQ3
DACK3#
IOR#
IOW#
SA17
SMEMR#
AEN
VCC
SMEMW#
SD1
NOWS#
SD4
IRQ9
SD7
RSTDRV
GND

18

Connectors and Jumpers

ETX X3 Connector

Pin
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
61
63
65
67
69
71
73
75
77
79
81
83
85
87
89
91
93
95
97
99

Signal Name
GND
RED
HSYNC
VSYNC
PAL_DETECT#
LCDDO16
LCDDO17
GND
LCDDO13
LCDDO12
GND
LCDDO8
LCDDO9
GND
LCDDO4
LCDDO5
GND
LCDDO1
LCDDO0
VCC
JILI_DAT
JILI_CLK
BIASON
TV_COMP
TV_SYNC
LPT/FLPY#
VCC
STB#
RESERVED
IRRX
IRTX
RXD2
GND
RTS2#
DTR2#
DCD2#
DSR2#
CTS2#
TXD2
RI2#
VCC
RXD1
RTS1#
DTR1#
DCD1#
DSR1#
CTS1#
TXD1
RI1#
GND

Pin
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
62
64
66
68
70
72
74
76
78
80
82
84
86
88
90
92
94
96
98
100

Signal Name
GND
BLUE
GREEN
DDC2B_CLK
DDC2B_DAT
LCDDO18
LCDDO19
GND
LCDDO15
LCDDO14
GND
LCDDO11
LCDDO10
GND
LCDDO7
LCDDO6
GND
LCDDO3
LCDDO2
VCC
FLM
BLON#
PLPWR_EN
TV_Y
TV_C
RESERVED
GND
AFD#
PD7
ERR#
PD6
INIT#
GND
PD5
SLIN#
PD4
PD3
PD2
PD1
PD0
VCC
ACK#
BUSY#
PE
SLCT#
MSCLK
MSDAT
KBCLK
KBDAT
GND

Connectors and Jumpers

 19

ETX X4 Connector

Pin
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
61
63
65
67
69
71
73
75
77
79
81
83
85
87
89
91
93
95
97
99

Signal Name
GND
5V_SB
PS_ON
PWRBTN#
KBINH
RSMRST#
ROMKBCS#(1)
EXT_PRG(1)
VCC
OVCR#
EXTSMI#
SMBCLK
SIDE_CS3#
SIDE_CS1#
SIDE_A2
SIDE_A0
GND
PDIAG_S
SIDE_A1
SIDE_INTRQ
BATLOW#
SIDE_ACK#
SIORDY
SIDE_IOR#
VCC
SIDE_IOW#
SIDE_DRQ
SIDE_D15
SIDE_D0
SIDE_D14
SIDE_D1
SIDE_D13
GND
SIDE_D2
SIDE_D12
SIDE_D3
SIDE_D11
SIDE_D4
SIDE_D10
SIDE_D5
VCC
SIDE_D9
SIDE_D6
SIDE_D8
GPE2#
RXD-
RXD+
TXD-
TXD+
GND

Pin
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
62
64
66
68
70
72
74
76
78
80
82
84
86
88
90
92
94
96
98
100

Signal Name
GND
PWGIN
SPEAKER
BATT
LILED
ACTLED
SPDLED
I2CLK
VCC
GPCS#(1)
I2DAT
SMBDATA
SMBALRT#
DASP_S(1)
PIDE_CS3#
PIDE_CS1#
GND
PIDE_A2
PIDE_A0
PIDE_A1
GPE1#
PIDE_INTRQ
PIDE_ACK#
PIORDY
VCC
PIDE_IOR#
PIDE_IOW#
PIDE_DRQ
PIDE_D15
PIDE_D0
PIDE_D14
PIDE_D1
GND
PIDE_D13
PIDE_D2
PIDE_D12
PIDE_D3
PIDE_D11
PIDE_D4
PIDE_D10
VCC
PIDE_D5
PIDE_D9
PIDE_D6
CBLID_P#
PIDE_D8
SIDE_D7
PIDE_D7
HDRST#
GND

20

Connectors and Jumpers

2.2 Jumper Settings

CF Mode Selection (JP2)

 1

2

3

Jumper

1-2

2-3

Panel Power Selection (JP3)

 1

2

3

Jumper

1-2

2-3

Status

Master

Slave

Status

+5V

+3.3V

Connectors and Jumpers

 21

22

Connectors and Jumpers

3 System Resources

3.1 Interrupt Assignments

PCI  and  ISA  interrupts  supported  by  the  VIA  VT82C686B  South
Bridge are as follows:

ISA IRQ Edge/ Level Polarity

Interrupt Source

Notes

NMI

SMI

IRQ0

IRQ1

IRQ2

IRQ3

IRQ4

IRQ5

IRQ6

IRQ7

IRQ8_L

IRQ9

IRQ10

IRQ11

IRQ12

IRQ13

IRQ14

IRQ15

Edge

Edge

Edge

Edge

Edge

Edge

Edge

Edge

Edge

Edge

Edge

Edge

Level

Level

Edge

Edge

Edge

Edge

High

Low

High

High

High

High

High

Low

High

High

Low

Low

Low

Low

High

High

High

High

SERR_L asserted

VT82C686B Hardware Monitor

Timer0

Keyboard

Cascade Interrupt from Slave Inter-
rupt Controller

COM2

COM1

PCI PnP IRQ

FDC

LPT1

Real Time Clock

PCI PnP IRQ

PCI PnP IRQ

PCI PnP IRQ, USB

Mouse

FERR_L asserted

Primary IDE

Secondary IDE

(1)

(2)

(2)

(2)

(2)

(2)

(3)

(2)

(4)

(5)

Notes:

1.

Internally generated by the VT82C686B.

2. Suggested. These interrupts are plug and play compatible and

may be routed to any available interrupt.

3. The  USB  interrupt  is  internally  routed  to  the  PIRQD#  input  of

the VT82C686B.

4. This interrupt is routed to the IRQ14 input of the VT82C686B.

5. This interrupt is routed to the IRQ15 input of the VT82C686B.

System Resources

 23

3.2 PCI Bus Arbitration Assignment

PCI Bus REQ#/GNT#
(ETX Module)

Arbitor
(ProCB-795)

REQ0#/GNT0#

REQ1#/GNT1#

REQ2#/GNT2#

REQ3#/GNT3#

REQ4#/GNT4#

—

—

—

—

REQ5#/GNT5#

PCI Master)

IDSEL

LAN8139CL+

AD23

PCI Slot 1

PCI Slot 2

PCI Slot 3

PCI Slot 4

*

*

*

*

REQ6#/GNT6#

SATA Sil3114

AD19

*Note: AD28 ~ AD31 dependent on backplane.

3.3 PCI Interrupt Routing

Device

Net PIRQ0_L Net PIRQ1_L Net PIRQ2_L Net PIRQ3_L

PCI Slots 1-4
(Golden Fingers)

PIRQA#

PIRQB#

PIRQC#

PIRQD#

LAN 8139CL+

PIRQD#

SATA Sil3114

—

—

—

—

—

—

—

24

System Resources

3.4 Memory Map

Address

00000000-0009FFFF

000A0000-000BFFFF

000C0000-000DFFFF

000F0000-000FFFFF

Size

640k

128k

1M

64k

Description

DOS Application Area

Video Buffer Area

Expansion Area

System BIOS Area

000E0000-000EFFFF

64k Extended System BIOS Area

00100000-DRAMTop

—

System memory area

DRAM Top-FFFRFFFF —

Bus area

FFFEFFFF-FFFFFFFF

64k

Initialization area

3.5 Direct Memory Access Channels

DMA# Available

0

1

2

3

4

5

6

7

Yes

Yes

No

Yes

No

Yes

Yes

Yes

Description

—

Unavailable if Sound Blaster is enabled with
default configuration

Used by FDC

Unavailable when LPT is in ECP mode

Used for Cascade

—

—

—

System Resources

 25

3.6 I/O Address Map

Address

Size

Description

0000-001F

32 bytes

Master DMA controller

0020 - 002D 14 bytes

Master Interrupt Controller

0040 - 005F 32 bytes

Timer/Counter

0060 - 006F 32 bytes

Keyboard Controller

60h

61h

64h

1 byte

KBC data

1 byte Misc function and Speaker control

1 byte

KBC command / status

0070 - 0077

8 bytes

RTC/CMOS/NMI-Disable

0078 - 007F

8 bytes

Available for system use

0080

1 byte

Reserved (Debug port)

0081 - 008F 16 bytes

DMA page registers

0090-0091

2 bytes

Available for system use

0092

1 byte

System Control

0093 - 009F 13 bytes

Available for system use

00A0-00BF 32 bytes

Slave Interrupt Controller

00C0-00DF 32 bytes

Slave DMA Controller

00E0-00FF 32 bytes

Available for system use

0100-0CF7

Available for system use

0CF8 -0CFB 4 bytes

PCI configuration address

0CFC - 0CFF 4 bytes

PCI configuration data

0D00 - FFFF

—

Available for system use

26

System Resources

3.7 System Management Bus (I2C)
The System Management Bus (SMB) controller is integrated
into the VT82C686B chip on the ETX-EV133. There are sev-
eral slave devices that reside on the SMB. Their addresses
are as follows:

Address

1010000

1011110

Function

Device

Identification Info

SODIMM0

CMOS setting backup

EEPROM

Inside LAN ID

Control and Status

Ethernet # 1

System Resources

 27

28

System Resources

4 Phoenix Award BIOS

4.1 Description

The ETX-EV133 module has a Phoenix Award PCI/ISA BIOS ver.
6.0  for  system  configuration.  The  Award  BIOS  setup  program  is
designed to provide maximum flexibility in configuring the system
by  offering  various  options  that  can  be  tailored  for  end-user
requirements.  This  chapter  is  written  to  assist  you  in  the  proper
usage of these features.

4.2 Main Menu

To  access  the  Phoenix  AWARD  PCI/ISA  BIOS  Setup  program,
press <Del>   key immediately after powering up the system. The
Main Menu will be displayed.

Figure 4-1: AWARD BIOS Main Menu

Phoenix Award BIOS

 29

(cid:88) Standard CMOS Features: Use this menu for basic system

configuration (see Section 4.3).

(cid:88) Advanced BIOS Features: Use this menu to set the

Advanced Features available on your system (see Section
4.4).

(cid:88) Advanced Chipset Features: Change values in the

chipset registers and optimize your system's performance
(see Section 4.5).

(cid:88) Integrated Peripherals: Use this menu to specify your set-

tings for integrated peripherals (see Section 4.6).

(cid:88) Power Management Setup: Use this menu to specify your

settings for power management (see Section )4.7.

(cid:88) PnP/PCI Configuration: This entry appears if your system

supports PnP/PCI (see Section 4.8).

(cid:88) PC Health Status: Use this menu to specify your settings

for frequency/voltage control (see Section 4.9).

(cid:88) Load Fail-Safe Defaults: Loads the BIOS default values

for the minimal/stable performance for your system to oper-
ate.

(cid:88) Load Optimized Defaults: Loads the BIOS default values
that are factory settings for optimal system performance.

(cid:88) Supervisor / User Password: Use this menu to set User

and Supervisor Passwords.

(cid:88) Save & Exit Setup: Save CMOS value changes to CMOS

and exit setup.

(cid:88) Exit Without Saving: Abandon all CMOS value changes

and exit setup.

30

Phoenix Award BIOS

4.3 Standard CMOS Features

Figure 4-2: Standard CMOS Features Menu

The main menu includes the following main setup categories.

(cid:88) Date: The BIOS determines the day of the week from other

date information; this field is for information only.

(cid:88) Time: The time format is based on the 24-hour military-time
clock. For example, 1 p.m. is 13:00:00. Press the ( key to
move to the desired field. Press the PgUp or PgDn key to
increment the setting, or type the desired value into the
field.

(cid:88) IDE Primary and Secondary Master/Slave Items: This

selection brings you a configuration menu of the designated
Drive.

Phoenix Award BIOS

 31

(cid:88) Drive A, B: Select the correct specifications for the diskette

drive(s) installed in the computer.

(cid:90) None: No diskette drive installed.

(cid:90) 360K: 5-1/4 inch PC-type standard drive.

(cid:90) 1.2M: 5-1/4 inch AT-type high-density drive.

(cid:90) 720K: 3-1/2 inch double-sided drive.

(cid:90) 1.44M: 3-1/2 inch double-sided drive.

(cid:90) 2.88M: 3-1/2 inch double-sided drive.

(cid:88) Floppy Mode 3 Support: Enables support for 1.2 MB for-
mat capacity on 3-1/2 inch disk drives. This format is com-
monly used Japan. Options are: disabled, drive A, drive B,
both.

(cid:88) Video: Select the type of primary video subsystem in your
computer. The BIOS usually detects the correct video type
automatically. The BIOS supports a secondary video sub-
system, but you do not select it in Setup.

(cid:88) Halt On: During the power-on self-test (POST), the com-

puter stops if the BIOS detects a hardware error. You can
tell the BIOS to ignore certain errors during POST and con-
tinue the boot-up process. These are the selections:

(cid:90) No errors: POST does not stop for any errors.

(cid:90) All errors: If any non-fatal error, POST stops and

prompts to take corrective action.

(cid:90) All, But Keyboard: POST does not stop for a keyboard

error, but stops for all other errors.

(cid:90) All, But Diskette: POST does not stop for diskette drive

errors, but stops for all other errors.

(cid:90) All, But Disk/Key: POST does not stop for keyboard /

disk error, but stops for all other errors.

32

Phoenix Award BIOS

IDE Primary and Secondary Master/Slave Items

Figure 4-3: IDE Primary and Secondary Master/Slave Items Menu

IDE HDD Auto-detection
Press Enter to auto-detect the HDD on this channel. If detec-
tion is successful, it fills the remaining fields on this menu.

Press Enter

NoneAutoManual

IDE Primary Master
Selecting  'manual'  lets  you  set  the  remaining  fields  on  this
screen. Selects the type of fixed disk. "User Type" will let you
select  the  number  of  cylinders,  heads,  etc.  Note:  PRE-
COMP=65535 means NONE!

Capacity
Disk drive capacity (Approximated). Note that this size is usu-
ally slightly greater than the size of a formatted disk given by a
disk checking program.

Auto Display disk size

Access Mode
Choose the access mode for this hard disk.

Normal/LBA/Large/Auto

Phoenix Award BIOS

 33

4.4 Advanced BIOS Features

This section allows you to configure your system for basic opera-
tion.  You  have  the  opportunity  to  select  the  system's  default
speed, boot-up sequence, keyboard operation, shadowing, secu-
rity.

Figure 4-4: Advanced BIOS Features Menu

Virus Warning
Allows  you  to  choose  the  VIRUS  Warning  feature  for  IDE  Hard
Disk  boot  sector  protection.  If  this  function  is  enabled  and  an
attempt  is  made  to  write  data  into  this  area,  BIOS  will  show  a
warning message on screen and alarm beep. Enabled: Activates
automatically when the system boots up causing a warning mes-

34

Phoenix Award BIOS

sage to appear when anything attempts to access the boot sector
or  hard  disk  partition  table.  Disabled:  No  warning  message  will
appear.

CPU Internal Cache / CPU External Cache
These  two  categories  speed  up  memory  access.  However,  it
depends  on  CPU/chipset  design.  Enabled:  Enable  cache,  Dis-
abled: Disable cache.

CPU L2 Cache ECC Checking
This item allows you to enable/disable CPU L2 Cache ECC check-
ing. Enabled, Disabled.

Quick Power On Self Test
This  category  speeds  up  Power  On  Self  Test  (POST)  after  you
power up the computer. If it is set to Enable, BIOS will shorten or
skip  some  check  items  during  POST.  Enabled  Enable  quick
POST. Disabled: Normal POST.

First / Second / Third Boot Device
Enter brings you to Boot Device Menu. The BIOS attempts to load
the operating system from the selected device. See menu for pos-
sible options.

Boot Other Device
When enabled the BIOS will try to boot from second or third option
if booting from first device fails. When disabled the BIOS will not
use the alternative devices.

Boot Up NumLock Status
Select  power  on  state  for  NumLock.  The  choice:  Enabled/Dis-
abled.

Gate A20 Option
Select  if  chipset  or  keyboard  controller  should  control  GateA20.
Normal:  A  pin  in  the  keyboard  controller  controls  GateA20  Fast:
Lets chipset control GateA20.

Typematic Rate Setting
Key strokes repeat at a rate determined by the keyboard control-
ler. When enabled, the typematic rate and typematic delay can be
selected. Choices: Enabled/Disabled.

Phoenix Award BIOS

 35

Typematic Rate (Chars/Sec)
Sets  the  number  of  times  a  second  to  repeat  a  key  stroke  when
you hold the key down. Choices: 6, 8,10,12,15, 20, 24, 30.

Typematic Delay (Msec)
Sets the delay time after the key is held down before it begins to
repeat the keystroke. Choices: 250, 500, 750, 1000.

Security Option
Select  whether  the  password  is  required  every  time  the  system
boots or only when you enter setup. Choices: System: the system
will not boot and access to Setup will be denied if the correct pass-
word is not entered at the prompt. Setup: The system will boot, but
access  to  Setup  will  be  denied  if  the  correct  password  is  not
entered  at  the  prompt.  To  disable  security,  select  PASSWORD
SETTING at Main Menu and then you will be asked to enter pass-
word. Do not type anything and just press <Enter>, it will disable
security.  Once  the  security  is  disabled,  the  system  will  boot  and
you can enter Setup freely.

OS Select For DRAM > 64MB
Select  the  operating  system  that  is  running  with  greater  than
64MB of RAM on the system. Choices: Non-OS2, OS2.

Console Redirection
Award's Preboot Agent provides you with console redirection to let
you control a remote PC or embedded system via modem or direct
serial connection at boot time. Choices: Enable, Disable.

Baudrate
Select baud rate: 9600,19200, 38400, 57600 and 115200.

Agent Connect via
Fixed to NULL (Null modem cable), no selection possible.

Agent wait time (min)
Timeout in minutes to install agent if no serial connection can be
established.

Agent after boot
Enable this option to keep the Agent running after OS boot.

Summary Screen Show
Suppress the summary screen. Choices: Enable, Disable.

36

Phoenix Award BIOS

4.5 Advanced Chipset Features

Figure 4-5: Advanced Chipset Features Menu

DRAM Clock
This  item  allows  you  to  set  the  DRAM  Clock.  Options  are  Host
CLK, HCLK+33M or HCLK-33M. Please set the item according to
the Host (CPU) Clock and DRAM Clock.

DRAM Timing by SPD
If your DIMM memory has SPD (Serial Presence Detect) 8-pin IC
on  module,  you  can  set  this  option  to  Enabled.  System  will  set
your DRAM clock and timing from the SPD IC. If the option is set
as Disabled, DRAM clock and timing must be set from the items
below. (SDRAM Cycle Length and Bank Interleave).

SDRAM Cycle Length
This feature is similar to SDRAM CAS Latency Time. It controls
the  time  delay  (in  clock  cycles  -CLKs)  that  passes  before  the
SDRAM starts to carry out a read command after receiving it.

Phoenix Award BIOS

 37

This also determines the number of CLKs for the completion of
the  first  part  of  a  burst  transfer.  Thus,  the  lower  the  cycle
length, the faster the transaction. However, some SDRAM can-
not  handle  the  lower  cycle  length  and  may  become  unstable.
So, set the SDRAM Cycle Length to 2 for optimal performance
if possible but increase it to 3 if your system becomes unstable.

Bank Interleave
This  feature  enables  you  to  set  the  interleave  mode  of  the
SDRAM  interface.  Interleaving  allows  banks  of  SDRAM  to
alternate  their  refresh  and  access  cycles.  One  bank  will
undergo its refresh cycle while another is being accessed. This
improves performance  of  the  SDRAM  by  masking the  refresh
time of each bank.

P2C/C2P Concurrency
This  item  allows  you  to  enable/disable  the  PCI  to  CPU,  CPU  to
PCI concurrency. Choices: Enabled, Disabled.

Video RAM Cacheable
Select Enabled allows caching of the video RAM, resulting in bet-
ter  system  performance.  However,  if  any  program  writes  to  this
memory area, a system error may result. Choices: Enabled, Dis-
abled.

OnChip USB
This should be enabled if your system has a USB installed on the
system board and you want to use it. Even when so equipped, if
you add a higher performance controller, you will need to disable
this feature. Choices: Enabled, Disabled.

USB Keyboard Support
Select  Enabled  if  your  system  contains  a  Universal  Serial  Bus
(USB)  controller  and  you  have  a  USB  keyboard.  Choices:
Enabled, Disabled.

OnChip Sound
This item allows you to control the onboard AC 97 audio. Choices:
Auto, Disabled.

CPU to PCI Write Buffer
When this field is Enabled, writes from the CPU to the PCI bus are
buffered,  to  compensate  for  the  speed  differences  between  the
CPU and the PCI bus. When Disabled, the writes are not buffered

38

Phoenix Award BIOS

and the CPU must wait until the write is complete before starting
another write cycle. Choices: Enabled, Disabled.

PCI Dynamic Bursting
This  item  allows  you  to  enable/disable  the  PCI  dynamic  bursting
function. Choices: Enabled, Disabled.

PCI Master 0 WS Write
When Enabled, writes to the PCI bus are executed with zero wait
states.

PCI Delay Transaction
The chipset has an embedded 32-bit posted write buffer to support
delay  transactions  cycles.  Select  Enabled  to  support  compliance
with PCI specification version 2.1. Choices: Enabled, Disabled.

PCI#2 Access #1 Retry
When  disabled,  PCI#2  will  not  be  disconnected  until  access  fin-
ishes (default). When enabled, PCI#2 will be disconnected if max
retries  are  attempted  without  success.  Choices:  Enabled,  Dis-
abled.

Phoenix Award BIOS

 39

4.6 Integrated Peripherals

Figure 4-6:  Integrated Peripherals Menu

OnChip IDE Channel 0/1
The chipset contains a PCI IDE interface with support for two IDE
channels.  Select  Enabled  to  activate  the  primary  IDE  interface.
Select Disabled to deactivate this interface.

Primary & Secondary Master/Slave PIO
The four IDE PIO (Programmed Input/Output) fields let you set a
PIO mode (0-4) for each of the four IDE devices that the onboard
IDE  interface  supports.  Modes  0  through  4  provide  successively
increased  performance.  In  Auto  mode,  the  system  automatically
determines the best mode for each device. Choice: Auto, Mode 0,
Mode 1, Mode 2, Mode 3, Mode 4.

40

Phoenix Award BIOS

Primary & Secondary Master/Slave UDMA
Ultra DMA implementation is possible only if your IDE hard drive
supports it and the operating environment includes a DMA driver.
If  your  hard  drive  and  your  system  software  both  support  Ultra
DMA, select Auto to enable BIOS support.

Init Display First
This  item  allows  you  to  decide  to  active  either  PCI  Slot  or  AGP
first.

IDE HDD Block Mode
This  feature  enhances  disk  performance  by  allowing  multi-sector
data transfers and eliminates the interrupt handling time for each
sector.

Onboard Serial Port 1 & 2
Select an address and corresponding interrupt for the first/second
serial port. The default value for the first serial port is "3F8/IRQ4"
and the second serial port is "2F8/IRQ3".

UART 2 Mode
This item allows you to select which mode for the Onboard Serial
Port 2. Choices: Standard, HPSIR, ASKIR.

IR Function Duplex
This  item  allows  you  to  select  the  IR  half/full  duplex  function.
Choices: Half, Full.
TX,RX inverting enable
This  item  allow  you  to  enable  the  TX,  RX  inverting  which
depends on different H/W requirement. This field is not recom-
mended to change its default setting for avoiding any error in
your  system  Choices:  No,  No/No,  Yes(Default)/Yes,  No/Yes,
Yes.

Onboard Parallel Port
Select address and interrupt for the Parallel port.

Onboard Parallel Mode
Select an operating mode for the parallel port. Mode options are
Normal, EPP, ECP, ECP/EPP.

ECP Mode Use DMA
Select  a  DMA  channel  if  parallel  Mode  is  set  as  ECP,  ECP/
EPP.
Parallel Port EPP Type
Select a EPP Type if parallel Port is set as EPP, ECP/EPP.

Phoenix Award BIOS

 41

4.7 Power Management Setup

Figure 4-7:  Integrated Peripherals Menu

ACPI Function
Select Enabled only if your computer's operating system supports
ACPI (the Advanced Configuration and Power Interface) specifica-
tion. Currently, Windows 98 and Windows 2000 support ACPI.

Power Management
There  are  4  selections  for  Power  Management  (other  than  Dis-
abled), 3 of which have fixed mode :

Disabled  (default):  No  power  management.  Disables  all  four
modes.

Min.  Power  Saving:  Minimum  power  management.  Doze
Mode = 1 hr., Standby Mode = 1 hr., Suspend Mode = 1 hr.,

Max. Power Saving: Maximum power management — ONLY
AVAILABLE  FOR  SL  CPU's.  Doze  Mode  =  1  min.,  Standby
Mode = 1 min., Suspend Mode = 1 min.

42

Phoenix Award BIOS

User Defined: Allows you to set each mode individually. When
not disabled, each of the ranges are from 1 min. to 1 hr.

HDD Power Down is always set independently

ACPI Suspend Type:

S1 (POS) Power On suspend: All devices are powered up
except for the clock synthesizer. The Host and PCI clocks
are inactive and PIIX4 provides control signals and 32-kHz
Suspend Clock (SUSCLK) to allow for DRAM refresh and to
turn off the clock synthesizer. The only power consumed in
the system is due to DRAM Refresh and leakage current of
the powered devices. When the system resumes from POS,
PIIX4  can  optionally  resume  without  resetting  the  system,
can reset the processor only, or can reset the entire system.
When  no  reset  is  performed,  PIIX4  only  needs  to  wait  for
the clock synthesizer and processor PLLs to lock before the
system is resumed. This takes typically 20 ms.

S3 (STR) Suspend To RAM: Power is removed from most
of the system components during STR, except the DRAM.
Power  is  supplied  to  Suspend  Refresh  logic  in  the  Host
Controller, and RTC and Suspend Well logic in PIIX4. PIIX4
provides control signals and 32-kHz Suspend Clock (SUS-
CLK)  to  allow  for  DRAM  refresh  and  to  turn  off  the  clock
synthesizer and other power planes.

PM Control By APM
When  enabled,  an  Advanced  Power  Management  device  will  be
activated to enhance the Max. Power Saving mode and stop the
CPU internal clock. If  Max. Power Saving is not enabled, this will
be preset to No.

Video Off Option
Controls what causes the display to be switched off:

(cid:90) Suspend -> Off

(cid:90)  Always On

(cid:90)  All Mode -> Off

Phoenix Award BIOS

 43

Video Off Method
This determines the manner in which the monitor is blanked.

(cid:90) V/H SYNC+Blank causes the system to turn off the verti-
cal and horizontal synchronization signals and writes
blanks to the screen.

(cid:90) Blank Screen: This option only writes blanks to the

screen.

(cid:90) DPMSInitial: Display power management signaling.

(cid:90) Modem Use IRQ: Name the interrupt request (IRQ)

assigned to the modem (if any) on your system. Activity
of the selected IRQ always awakens the system.

Soft-Off By PWRBTN
The  field  defines  the  power-off  mode  when  using  an  ATX  power
supply.  The  Instant-Off  mode  means  powering  off  immediately
when  pressing  the  power  button.  In  the  Delay  4  Sec  mode,  the
system powers off when the power button is pressed for more than
four  seconds  or  places  the  system  in  a  very  low-power-usage
state,  with only enough circuitry receiving power to detect power
button activity or resume by ring activity when press for less than
four seconds. The default is 'Instant-Off'.

State After Power Failure
On: After a power failure, the system will automatically reboot
as soon as power is restored.

Off:  After  a  power  failure,  the  system  will  not  reboot  when
power  is  restored.  The  system  needs  to  be  turned  on  again
manually.

Auto: After a power failure, the system will automatically reboot
as  soon  power  is  restored  if  the  PC  was  turned  on  when  the
power failed. If the PC was already turned off when the power
failed, the system needs to be turned on again manually.

44

Phoenix Award BIOS

Wake Up Events
Setting an event on each device listed to awaken the system from
a soft off state.

(cid:90) VGA

(cid:90) LPT & COM

(cid:90) HDD & FDD

(cid:90) PCI Master

(cid:90) Power On by PCI Card

(cid:90) Wake Up on LAN/Ring

(cid:90) RTC Alarm Resume

(cid:90) Date (of Month)

(cid:90) Resume Time (hh:mm:ss)

(cid:90) Primary INTR

(cid:90) IRQs Activity Monitoring

Phoenix Award BIOS

 45

4.8 PnP/PCI Configuration

Figure 4-8: PnP/PCI Configuration Menu

This section describes configuration of the PCI bus system. PCI,
or Personal Computer Interconnect, is a system which allows I/O
devices  to  operate  at  speeds  nearing  the  speed  the  CPU  itself
uses when communicating with its own special components.

Reset Configuration Data
Normally,  you  leave  this  field  Disabled.  Select  Enabled  to  reset
ESCD  (Extended  System  Configuration  Date)  when  you  exit
Setup if you have installed a new add-on and the system reconfig-
uration has caused such a serious conflict that the operating sys-
tem cannot boot.

Resource Controlled By
The  Award  Plug  and  Play  BIOS  can  automatically  configure  all
boot and Plug-and-Play compatible devices. If you select Auto, all
the interrupt request (IRQ) and DMA assignment fields disappear,
as the BIOS automatically assigns them.

46

Phoenix Award BIOS

IRQ Resources
When  resources  are  controlled  manually,  assign  each  system
interrupt  as one  of  the  following  types,  depending on the  type of
device using the interrupt.

Legacy  ISA:  Devices  compliant  with  the  original  PC/AT  bus
specification,  requiring  a  specific  interrupt  (such  as  IRQ4  for
serial port 1).

PCI/ISA  PnP:  Device  compliant  with  the  Plug  and  Play  stan-
dard, whether designed for PCI or ISA bus architecture.

DMA Resources
When  resources  are  controlled  manually,  assign  each  system
DMA channel as one of the following types, depending on the type
of device using the DMA.

Legacy  ISA:  Devices  compliant  with  the  original  PC/AT  bus
specification, requiring a specific DMA channel.

PCI/ISA PnP: Devices compliant with the Plug and Play stan-
dard, whether designed for PCI or ISA bus architecture.

PCI/VGA Palette Snoop
Normally this option is always Disabled! Nonstandard VGA display
adapters  such  as  overlay  cards  or  MPEG  video  cards  may  not
show colors properly. Setting Enabled should correct this problem.
If this field set Enabled, any I/O access on the ISA bus to the VGA
card's palette registers will be reflected on the PCI bus. This will
allow overlay cards to adapt to the changing palette colors.

4.9 PC Health Status

CPU Warning Temperature
Brings up a submenu that lets you assign a temperature level that
is not to be exceeded by the CPU. If the CPU temperature goes
over this limit a audio warning signal sounds

Current CPU Temp.
Displays the current CPU temperature.

Current System Temp.
Displays the current system temperature.

Phoenix Award BIOS

 47

Vcore, 2.5V, 3.3V, 5V
Displays the actual voltage levels on the board.

Case Open Warning
When  enabled  an  audible  signal  is  generated  when  pin  GPE1#
and CBLID_P# on X4 are disconnected.

4.10 BIOS POST Codes

POST (hex)

Description

CFh

Test CMOS R/W functionality.

 C0h

 C1h

 C3h

 C5h

 0h1

 02h

 03h

 04h

 05h

 06h

 07h

Early chipset initialization:
- Disable shadow RAM
- Disable L2 cache (socket 7 or below)
- Program basic chipset registers

Detect memory

- Auto-detection of DRAM size, type and ECC
 - Auto-detection of L2 cache (socket 7 or below)

Expand compressed BIOS code to DRAM

Call chipset hook to copy BIOS back to E000 & F000 shadow
RAM.

Expand the Xgroup codes locating in physical address 1000:0

Reserved

Initial Superio_Early_Init switch.

Reserved

1. Blank out screen
2. Clear CMOS error flag

Reserved

1. Clear 8042 interface
2. Initialize 8042 self-test

1. Test special keyboard controller for Winbond 977 series

 08h

 Super I/O chips.

2. Enable keyboard interface.

 09h

Reserved

 0Ah

1. Disable PS/2 mouse interface (optional).
2. Auto detect ports for keyboard & mouse followed by a port

& interface swap (optional).

3. Reset keyboard for Winbond 977 series Super I/O chips.

48

Phoenix Award BIOS

POST (hex)

Description

 0Bh

 0Ch

 0Dh

 0Eh

 0Fh

 10h

 11h

 12h

 13h

 14h

 15h

 16h

 17h

 18h

19h

 1Ah

1Bh

 1Ch

 1Dh

 1Eh

 1Fh

 20h

 21h

 22h

Reserved

Reserved

Reserved

Test F000h segment shadow to see whether it is R/W-able or
not. If test fails, keep beeping the speaker.

Reserved

Auto detect flash type to load appropriate flash R/W codes into
the  run time area in F000 for ESCD & DMI support.

Reserved

Use walking 1's algorithm to check out interface in CMOS  cir-
cuitry.  Also set real-time clock power status, and then check for
override.

Reserved

Program chipset default values into chipset.  Chipset default
values are MODBINable by OEM customers.

Reserved

Initial Early_Init_Onboard_Generator switch.

Reserved

Detect CPU information including brand, SMI type (Cyrix or
Intel) and CPU level (586 or 686).

Reserved

Reserved

Initial interrupts vector table.  If no special specified, all H/W
interrupts are directed to SPURIOUS_INT_HDLR & S/W  inter-
rupts to SPURIOUS_soft_HDLR.

Reserved

Initial EARLY_PM_INIT switch.

Reserved

Load keyboard matrix (notebook platform)

Reserved

HPM initialization (notebook platform)

Reserved

Phoenix Award BIOS

 49

POST (hex)

Description

1. Check validity of RTC value:e.g. a value of 5Ah is an

invalid value for RTC minute.

2. Load CMOS settings into BIOS stack. If CMOS checksum

 fails, use default value instead.

3. Prepare BIOS resource map for PCI & PnP use. If ESCD is

valid, take into consideration of the ESCD's legacy
information.

4. Onboard clock generator initialization.  Disable respective

clock resource to empty PCI & DIMM slots.

5. Early PCI initialization:

- Enumerate PCI bus number
- Assign memory & I/O resource
- Search for a valid VGA device & VGA BIOS, and put it
   into C000:0.

Reserved

Reserved

Reserved

Initialize INT 09 buffer

Reserved

1. Program CPU internal MTRR (P6 & PII) for 0-640K

memory address. 2. Initialize the APIC for Pentium class CPU.

3. Program early chipset according to CMOS setup.
4. Measure CPU speed.
5. Invoke video BIOS.

Reserved

Reserved

Reserved

1. Initialize multi-language
2. Put information on screen display, including Award title, CPU

type, CPU speed ….

Reserved

Reserved

Reserved

Reserved

Reserved

Reset keyboard except Winbond 977 series Super I/O chips.

Reserved

 23h

 24h

 25h

 26h

 27h

 28h

 29h

 2Ah

 2Bh

 2Ch

 2Dh

 2Eh

 2Fh

 30h

 31h

 32h

 33h

 34h

50

Phoenix Award BIOS

POST (hex)

Description

 35h

 36h

 37h

 39h

 3Ah

 38h

 3Bh

 3Ch

 3Dh

 3Eh

 3Fh

 40h

 41h

 42h

 43h

 44h

 45h

 46h

 47h

 48h

Test DMA Channel 0

Reserved

Test DMA Channel 1

Test DMA Page Registers

Reserved

Reserved

Reserved

Test 8254 Channel 2

Reserved

Test 8259 interrupt mask bits for channel 1.

Reserved

Test 8259 interrupt mask bits for channel 2.

Reserved

Reserved

Test 8259 functionality.

Reserved

Reserved

Reserved

Initialize EISA slot

Reserved

1. Calculate total memory by testing the last double word of

 49h

each 64K page.

2. Program writes allocation for AMD K5 CPU.

 4Ah

 4Bh

 4Ch

 4Dh

Reserved

Reserved

Reserved

Reserved

1. Program MTRR of M1 CPU2.
2.Initialize L2 cache for P6 class CPU & program CPU with

proper cacheable range.

 4Eh

3. Initialize the APIC for P6 class CPU.
4. On MP platform, adjust the cacheable range to smaller

one in case the cacheable ranges between each CPU are
not identical.

Phoenix Award BIOS

 51

POST (hex)

Description

 4Fh

 50h

 51h

 52h

 53h

 54h

 55h

 56h

 57h

 58h

 59h

 5Ah

 5Bh

 5Ch

 5Dh

 5Eh

 5Fh

 60h

 61h

 62h

 63h

 64h

 65h

 66h

 67h

 68h

 69h

 6Ah

Reserved

Initialize USB

Reserved

Test all memory (clear all extended memory to 0)

Reserved

Reserved

Display number of processors (multi-processor platform)

Reserved

1. Display PnP logo
2. Early ISA PnP initialization
3. Assign CSN to every ISA PnP device.

Reserved

Initialize the combined Trend Anti-Virus code.

Reserved

Test EISA available memory

Reserved

1. Initialize Init_Onboard_Super_IO switch.
2. Initialize Init_Onbaord_AUDIO switch.

Reserved

Reserved

Okay to enter Setup utility; i.e. not until this POST stage can
users  enter the CMOS setup utility.

Reserved

Reserved

Reserved

Reserved

Initialize PS/2 Mouse

Reserved

Prepare memory size information for function call:   INT 15h
ax=E820h

Reserved

Turn on L2 cache

Reserved

52

Phoenix Award BIOS

POST (hex)

Description

 6Bh

 6Ch

 6Dh

 6Eh

 6Fh

 70h

 71h

 72h

 73h

 74h

 75h

 76h

 77h

 78h

 79h

 7Ah

 7Bh

 7Ch

 7Dh

 7Eh

 7Fh

 80h

 81h

 82h

Program chipset registers according to items described in Setup
& Auto-configuration table.

Reserved

1. Assign resources to all ISA PnP devices.
2. Auto assign ports to onboard COM ports if the corresponding

item in Setup is set to "AUTO".

Reserved

1. Initialize floppy controller
2. Set up floppy related fields in 40:hardware.

Reserved

Reserved

Reserved

Initialize fixed disk controller

Reserved

Detect & install all IDE devices: HDD, LS120, ZIP, CDROM…..

Reserved

Detect serial ports & parallel ports.

Reserved

Reserved

Detect & install co-processor

Reserved

Reserved

Reserved

Reserved

Switch back to text mode if full screen logo is supported.

- If errors occur, report errors & wait for keys
- If no errors occur or F1 key is pressed to continue:
  Clear EPA or customization logo.

Reserved

Reserved

1. Call chipset power management hook.
2. Recover the text fond used by EPA logo (not for full screen

logo)

3. If password is set, ask for password.

 83h

Save all data in stack back to CMOS

Phoenix Award BIOS

 53

POST (hex)

Description

 84h

Initialize ISA PnP boot devices

1. USB final Initialization
2. NET PC: Build SYSID structure
3. Switch screen back to text mode
4. Set up ACPI table at top of memory.
5. Invoke ISA adapter ROMs
6. Assign IRQs to PCI devices
7. Initialize APM
8. Clear noise of IRQs.

Reserved

Reserved

Reserved

Reserved

Reserved

Reserved

Reserved

Read HDD boot sector information for Trend Anti-Virus code

1. Enable L2 cache
2. Program boot up speed
3. Chipset final initialization.
4. Power management final initialization
5. Clear screen & display summary table
6. Program K6 write allocation
7. Program P6 class write combining

1. Program daylight saving
2. Update keyboard LED & typematic rate

1. Build MP table
2. Build & update ESCD
3. Set CMOS century to 20h or 19h
4. Load CMOS time into DOS timer tick
5. Build MSIRQ routing table.

85h

 86h

 87h

 88h

 89h

 90h

 91h

 92h

 93h

 94h

 95h

 96h

 FFh

Boot attempt (INT 19h)

54

Phoenix Award BIOS

5

 Driver Installation

This  chapter  describes  the  installation  procedure  for  all  device
drivers for the NuPRO-795 running Windows 2000/XP.

5.1 VIA Hyperion 4in1 Drivers

The  VIA  Hyperion  4in1  drivers  includes  four  system  drivers  to
improve performance and maintain stability of systems using VIA
chipsets. These four drivers are:

(cid:88) VIA Registry (INF) Driver

(cid:88) VIA AGP VxD driver

(cid:88) VIA ATAPI Vendor Support Driver

(cid:88) VIA PCI IRQ Miniport Driver

The VIA Hyperion 4in1 drivers automatically detect your operating
system and will install only the necessary drivers. The driver fea-
tures are as follows:

(cid:88) VIA IDE Bus Master Driver: For Windows NT users, the VIA

IDE Bus Mastering driver is the only driver that will be
installed on your system.

(cid:88) VIA Registry (INF) Driver will be installed. The driver will

enable the VIA Power Management function.

(cid:88) VIA AGP Vxd Driver will provide service routines for your

VGA driver and interface directly to hardware, providing fast
graphical access.

(cid:88) The IDE Filter driver enables the performance enhancing
bus mastering functions of ATA-capable hard disk drives
and ensures IDE device compatibility (also known as the
ATAPI Vendor Support Driver).

Installation Procedure

1. Operating  System  Requirements:  Windows  2000/XP
must be fully installed and running on the system prior to
installing drivers.

2. Close any running applications.

Driver Installation

 55

3. On

to
the  ADLINK  All-in-One  CD,  navigate
X:\NuPRO\NuPRO-795\Chipset  (where  X:  is  the  loca-
run
tion
VIAHyperion4in1453v.EXE.

CD-ROM

drive),

and

the

of

4. Bypass the Welcome dialog by clicking Next.

5. The readme file will appear, which contains similar infor-
mation to this installation guide. Click Yes to continue.

6. Keep the default setup and click Enable Normal Installa-

tion in Setup Mode Option. Click Next to continue.

7. Keep  the  default  setup  that  selects  all  three  items  VIA
PCI  IDE  Bus  Driver,  AGP  Driver  (AGP  3.0  Supported),
and  VIA  INF  Driver  2.00a  in  Setup  Mode  Option.  Click
Next to continue.

8. Keep  the  default  setup  that  selects Install  VIA  PCI  IDE
Bus  Driver  on  VIA  PCI  IDE  Bus  Driver  1.2a,  then  click
Next to continue.

9. Keep the default setup that selects Install AGP driver on
VIA_GART  AGP  Driver  4.42b,  then  click  Next  to  con-
tinue.

10.The Hyperion 4in1 drivers will automatically detect which
drivers you need and will tick the boxes corresponding to
the necessary drivers. It is recommended that you leave
these  boxes  as  they  appear,  unless  you  are  an
advanced user. Click Next.

11.You will be presented with a window that reads:

Set up has finished copying files to your computer.
Before you can use the program you must restart
Windows  or your  computer.  Yes  I  want  to restart
my computer now (ticked by default).

Remove  any  disks  from  your  drives  and  then  click
Finish to complete the installation.

12.Your computer will restart itself and the installation pro-

cess is complete.

56

Driver Installation

5.2 VGA Driver

This section provides information on how to install the VGA driver
that  comes  on  the  ADLINK  All-in-One  CD.  Please  follow  the
instructions set forth in this section carefully. Note that the appro-
priate operating  system  must be  installed on  your system before
you can install the VGA driver.

The following section describes the display driver installation pro-
cedure for Windows 2000/XP.

Installation Procedure

1. Boot Windows 2000/XP.

2. The  driver  is  included  on  the  ADLINK  All-in-One  CD.
directory:
Run  SETUP.exe
X:\NuPRO\NuPRO-795\VGA\Setup  (where  X:  is  the
location of the CD-ROM drive).

following

the

in

3. Click Next on the Welcome screen to read and agree to

the license agreement.

4. Click  Yes  if  you  agree  to  continue.  (NOTE:  If  you  click

No, the program will terminate.)

5. Click Yes to restart your computer to allow the new set-

tings to take effect.

6. Follow the screen instructions and use default settings to

complete setup when Windows 2000/XP restarts.

5.3 Realtek RTL8139CL+ Ethernet Controller

This  chapter  describes  the  LAN  driver  installation  for  the
RTL8139CL+  onboard  Ethernet  controller.  The  relevant  drivers
are  in  the  following  directory  on  the  ADLINK  All-in-One  CD:
X:\NuPRO\NuPRO-795\LAN (where X: is the location of the CD-
ROM drive).

In the following section, we will describe the LAN driver installation
for Windows 2000/XP.

Driver Installation

 57

Installation Procedure

Although  Windows  2000/XP  may  automatically  install  a  LAN
driver,  to  ensure  compatibility  we  recommend  that  you  manually
install the most up-to-date driver which is included on the ADLINK
All-in-One CD. After installing Windows 2000, please update to the
new driver using the following procedure.

1. Boot  Windows  2000/XP,  click  Start,  select  Settings,

and then double-click  Control Panel.

2. Double-click  the  System  icon,  click  the  Hardware  tab,

and click the Device Manager button.

3. Double-click  Network  Adapters,  then  double-click  the
Realtek RTL 8139C+ PCI Fast Ethernet Adapter entry.

4. Click  the  Driver  tab,  then  click  the  Update  Driver  but-

ton.

5. An  Upgrade  Device  Driver  Wizard  will  appear.  Click

Next.

6. Select Display a list of … and click Next. The next win-

dow may show a list of hardware models.

7.

Insert the ADLINK All-in-One CD and click Have Disk.

8. Browse to the RTL-8139C+ driver in the following path:
Select

X:\NuPRO\NuPRO-795\LAN\Win2000.
Netrts5.inf, click Open, then click OK.

9. Select  Realtek  RTL8139CL+  PCI  Fast  Ethernet
Adapter,  then  click  Next.  An  Update  Driver  Warning
window may pop up, click Yes to continue.

10.Click Next when the Wizard Summary window appears.

11.Click the Finish button, then click the Close button.

5.4 Audio Driver

This section describes the Audio driver installation for the Avance
AC’97 onboard Audio controllers. The relevant driver is located in
the
the  ADLINK  All-in-One  CD:
following  directory  on
X:\NuPRO\NuPRO-795\Audio.

58

Driver Installation

The following section describes the display driver installation pro-
cedure for Windows 2000/XP.

Installation Procedure

1. Boot Windows 2000/XP.

2. Locate  the  directory  X:\NuPRO\NuPRO-795\Audio  on

the CD-ROM, and run wdm_a362.exe.

3. Click Next on the Welcome screen, and then click Next

to continue driver installation.

4. Finally, click Finish to re-start.

Driver Installation

 59

60

Driver Installation

6

 Watchdog Timer

The NuPRO-795 includes a watchdog timer (WDT) that consists of
a one-second resolution down counter. Once a value is written to
the  WDT,  the  timer  automatically  starts  to  count  down.  If  the
counter ever reaches zero before the software restarts it, the soft-
ware  is  presumed  to  be  malfunctioning  and  the  processor's
RESET signal is asserted.

The watchdog function can be enabled or disabled by setting the
control register at I/O port 440h and 443h.

Status

Action

Enable / Refresh the Watchdog Timer Write timeout value to address 440h

Disable the Watchdog Timer.

Read 443h

Programming Examples:

Enable Watchdog Timer:

Write Timeout value to I/O port 440h

mov dx, 440

mov al, <0~255>

out dx, al

Disable Watchdog Timer:

Write and Value to I/O port 443h

mov dx, 443h

mov al, 1<0-255>

out dx, al

Value

Timeout

0

1

2

3

4

5

6

7

8

9

A

B

C

D

E

F

…

FF

None

1 sec

2 sec

3 sec

4 sec

5 sec

6 sec

7 sec

8 sec

9 sec

10 sec

11 sec

12 sec

13 sec

14 sec

15 sec

…

255 sec

Watchdog Timer

 61

62

Watchdog Timer

Warranty Policy

Thank  you  for  choosing  ADLINK.  To  understand  your  rights  and
enjoy all the after-sales services we offer, please read the follow-
ing carefully.

1. Before  using  ADLINK’s  products  please  read  the  user
manual and follow the instructions exactly. When sending in
damaged  products  for  repair,  please  attach  an  RMA
application
from:
http://rma.adlinktech.com/policy/.

form  which  can  be  downloaded

2. All ADLINK products come with a two-year guarantee:

(cid:88)The  warranty  period  starts  from  the  product’s  shipment

date from ADLINK’s factory.

(cid:88)Peripherals and third-party products not manufactured by
ADLINK  will  be  covered  by  the  original  manufacturers'
warranty.

(cid:88)For  products  containing  storage  devices  (hard  drives,
flash cards, etc.), please back up your data before send-
ing them for repair. ADLINK is not responsible for loss of
data.

(cid:88)Please ensure the use of properly licensed software with
our  systems.  ADLINK  does  not  condone  the  use  of
pirated software and will not service systems using such
software. ADLINK will not be held legally responsible for
products  shipped  with  unlicensed  software  installed  by
the user.

(cid:88)For  general  repairs,  please  do  not  include  peripheral
accessories.  If  peripherals  need  to  be  included,  be  cer-
tain to specify which items you sent on the RMA Request
&  Confirmation  Form.  ADLINK  is  not  responsible  for
items  not  listed  on  the  RMA  Request  &  Confirmation
Form.

Warranty Policy

 63

3. Our repair service is not covered by ADLINK's two-year

guarantee in the following situations:

(cid:88)Damage caused by not following instructions in the user's

manual.

(cid:88)Damage caused by carelessness on the user's part during

product transportation.

(cid:88)Damage  caused  by  fire,  earthquakes,  floods,  lightening,
pollution,  other  acts  of  God,  and/or  incorrect  usage  of
voltage transformers.

(cid:88)Damage caused by unsuitable storage environments (i.e.
high temperatures, high humidity, or volatile chemicals).

(cid:88)Damage caused by leakage of battery fluid during or after

change of batteries by customer/user.

(cid:88)Damage  from  improper  repair  by  unauthorized  techni-

cians.

(cid:88)Products with altered and/or damaged serial numbers are

not entitled to our service.

(cid:88)Other categories not protected under our warranty.

4. Customers  are  responsible  for  shipping  costs  to  transport

damaged products to our company or sales office.

5. To  ensure  the  speed  and  quality  of  product  repair,  please
download an RMA application form from our company web-
site:  http://rma.adlinktech.com/policy.  Damaged  products
with attached RMA forms receive priority.

If you have any  further questions, please email our FAE staff:
service@adlinktech.com.

64

Warranty Policy


[🔗 Link to the original document](.nupro-795series-manual-1/nupro-795series-manual-1.pdf)