# NuPRO-935A

Full-Sized PICMG 1.0 SBC

Intel® Q35/ICH9 Chipset

User's Manual

![Close-up of a green printed circuit board with various electronic components and connectors (no visible text or symbols)](.nupro-935a-50-13060-1030-204-en/df883074ad9639bc3dcbf492f8fc037a7e0f1b88efeacd60cfdd217b07e5a64e.jpg)

Manual Rev.: 2.04

Revision Date: April 26, 2011

Part No: 50-13060-1030

![Circular black-and-white recycling symbol with three white arrows forming a triangle (no text or symbols)](.nupro-935a-50-13060-1030-204-en/a33c45c660849437ecce2f8181e2f4f130746beb7205ad7be612a49bfb11c54a.jpg)

Recycled Paper

# Revision History

<table><tr><td>Revision</td><td>Release Date</td><td>Description of Change(s)</td></tr><tr><td>2.00</td><td>2008/08/29</td><td>Initial release</td></tr><tr><td>2.01</td><td>2008/10/29</td><td>Correct Board Layout (COM1/2)</td></tr><tr><td>2.02</td><td>2009/05/13</td><td>Update OS support, driver locations, add TPM driver installation</td></tr><tr><td>2.03</td><td>2010/07/03</td><td>Correct BIOS Power Button Mode description; correct CPU Fan connector, GbE connector, Floppy connector pin definitions; correct COM1 connector label (CN6); correct memory and heatsink/fan installation instructions; update addresses</td></tr><tr><td>2.04</td><td>2011/04/26</td><td>Remove Mini-DIN PS/2 KB/MS and legacy cables for boards with ordering numbers ending in “xx40” and higher; update addresses</td></tr></table>

# Preface

# Copyright 2008-2011 ADLINK Technology Inc.

This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer.

# Disclaimer

The information in this document is subject to change without prior notice in order to improve reliability, design, and function and does not represent a commitment on the part of the manufacturer.

In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.

# Environmental Responsibility

ADLINK is committed to fulfill its social responsibility to global environmental preservation through compliance with the European Union's Restriction of Hazardous Substances (RoHS) directive and Waste Electrical and Electronic Equipment (WEEE) directive. Environmental protection is a top priority for ADLINK. We have enforced measures to ensure that our products, manufacturing processes, components, and raw materials have as little impact on the environment as possible. When products are at their end of life, our customers are encouraged to dispose of them in accordance with the product disposal and/or recovery programs prescribed by their nation or company.

# Trademarks

Product names mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks of their respective companies.

# Using this Manual

# Audience and Scope

The NuPRO-935A User's Manual is intended for hardware technicians and systems operators with knowledge of installing, configuring and operating industrial grade single board computers.

# Manual Organization

This manual is organized as follows:

Preface: Presents important copyright notifications, disclaimers, trademarks, and associated information on the proper understanding and usage of this document and its associated product(s).

Chapter 1, Introduction: Introduces the NuPRO-935A, its features, applications, and specifications, including functional descriptions and board layout.

Chapter 2, Hardware Information: Provides technical information on connectors, jumpers and pin assignments for configuring the NuPRO-935A.

Chapter 3, Getting Started: Illustrates how to install components on the NuPRO-935A.

Chapter 4, Driver Installation: Provides information on how to install the NuPRO-935A device drivers.

Chapter 5, BIOS Setup: Describes basic navigation for the AMIBIOS®8 BIOS setup utility.

Appendix A, Watchdog Timer: Presents information on understanding and configuring the watchdog timer.

Appendix B, System Resources: Presents information on I/O mapping, IRQ routing, and resource allocation.

Important Safety Instructions: Presents safety instructions all users must follow for the proper setup, installation and usage of equipment and/or software.

Getting Service: Contact information for ADLINK's worldwide offices.

# Conventions

Take note of the following conventions used throughout this manual to make sure that users perform certain tasks and instructions properly.

![The image displays a digital icon of a white piece of paper with a folded top-left corner and faint horizontal lines running across it. A large, red checkmark is superimposed over the center of the document.](.nupro-935a-50-13060-1030-204-en/91c09104828b2ec409494086b951515e9dd857bee3a922f758d8d098cad00537.jpg)
NOTE:

Additional information, aids, and tips that help users perform tasks.

![The image shows a yellow triangular warning sign with a thick black border. Inside the triangle is a large black exclamation point centered within the shape.](.nupro-935a-50-13060-1030-204-en/a4e5ebe33fc8ea13ab8a1d32c0f60035c90547ff51d332c234f44260b6fffaa2.jpg)
CAUTION:

Information to prevent minor physical injury, component damage, data loss, and/or program corruption when trying to complete a task.

![The image features a red equilateral triangle centered on a white background. Inside the triangle is a large white exclamation point.](.nupro-935a-50-13060-1030-204-en/50c4455ad3bbf6ddc2eb98b37fe55081b91b394a9e1b778b4464c5340b361507.jpg)
WARNING:

Information to prevent serious physical injury, component damage, data loss, and/or program corruption when trying to complete a specific task.

This page intentionally left blank.

# Table of Contents

# Revision History...... ii

# Preface...... iii

# List of Figures ...... xi

# List of Tables...... xiii

# 1 Introduction ...... 1

1.1 Overview.... 1
1.2 Features.... 1
1.3 Specifications.... 2
1.4 Power Consumption 4
1.5 Block Diagram 5
1.6 Functional Description 6
1.7 Mechanical Drawing 9
1.8 I/O Connectivity 10
1.9 Package Contents 11

# 2 Hardware Information 13

2.1 Rear Panel I/O Ports.... 13
2.2 Board Layout 16
2.3 Onboard Connectors 18
2.4 Jumpers 25

# 3 Getting Started 27

3.1 Installing the CPU 27
3.2 Installing the CPU Fan and Heatsink.... 31
3.3 Installing the Power Connectors 34
3.4 Installing Memory Modules 35

# 4 Driver Installation.... 37

4.1 Intel® Q35 Express Chipset Driver 37
4.2 Display Driver.... 38
4.3 LAN Driver 38
4.4 ISA Driver.... 39
4.5 TPM Driver.... 39
4.6 Audio Driver 40

# 5 BIOS Setup 41

5.1 Starting the BIOS.... 41
5.2 Main Setup.... 45
5.3 Advanced BIOS Setup 46

5.3.1 CPU Configuration....47
5.3.2 IDE Configuration 48
5.3.3 Floppy Configuration....49
5.3.4 Super IO Configuration 50
5.3.5 Hardware Health Configuration 52
5.3.6 Remote Access Configuration 53
5.3.7 Trusted Computing 55
5.3.8 USB Configuration 56

5.4 Advanced PCI/PnP Settings 59
5.4.1 IRQ/DMA 59
5.4.2 ISA Plug and Play....60

5.5 Boot Settings 61
5.5.1 Boot Settings Configuration 61
5.5.2 Boot Device Priority 63
5.5.3 Boot Device Groups....63

5.6 Security Setup.... 64
5.7 Chipset Setup 67
5.7.1 South Bridge Configuration....68
5.7.2 Advanced Chipset Settings....69

5.8 Exit Menu.... 70

# A Appendix: Watchdog Timer....73

A.1 Sample Code 73

# B Appendix: System Resources....77

B.1 System Memory Map 77

B.2 Direct Memory Access Channels.... 78

B.3 IO Map 79

B.4 Interrupt Request (IRQ) Lines.... 81

# Important Safety Instructions 87

# Getting Service.... 89

This page intentionally left blank.

# List of Figures

Figure 1-1: NuPRO-935A Block Diagram .... 5
Figure 1-2: NuPRO-935A Board Dimensions (top view)......9
Figure 2-1: Rear Panel I/O Ports....13
Figure 2-2: Connectors and Jumpers Pt. 1 16
Figure 2-3: Connectors and Jumpers Pt. 2....17

This page intentionally left blank.

# List of Tables

Table 1-1: NuPRO-935A General Specifications....3
Table B-1: System Memory Map....77
Table B-2: Direct Memory Access Channels....78
Table B-3: IO Map 80
Table B-4: IRQ Lines PIC Mode 81
Table B-5: IRQ Lines APIC Mode 83
Table B-6: PCI Interrupt Request Routing....85
Table B-7: PCI Interrupt Routing Map 86

This page intentionally left blank.

# 1 Introduction

# 1.1 Overview

The ADLINK NuPRO-935A is a PICMG 1.0 industrial SBC supporting the next-generation Intel® Core 2 Quad/Duo and Intel® Celeron® processors in the LGA775 package to deliver a high performance platform for a wide array of industrial automation applications. The NuPRO-935A supports processing speeds up to 3.0 GHz and high-bandwidth network connectivity with PCI Express®-based gigabit LAN.

These advanced features, coupled with a dual-channel DDR2 system memory architecture and diverse I/O storage make the NuPRO-935A suitable for industrial automation and automation control applications requiring a standardize, easy-to-deploy, and cost-effective SBC.

# 1.2 Features

▶ Supports Intel® Core™2 Duo/ Core™2 Quad, processors in LGA775 package
▶ TPM hardware security chip (NuPRO-935A/DV only)
▶ Dual 10/100/1000Mbps Ethernet (NuPRO-935A/LV supports single GbE)
▶ Optional HD audio kit (DB-Audio2 daughter board)
▶ 5 USB 2.0 ports
▶ Supports 2 SATA II ports
▶ Watchdog Timer, Hardware Monitor
▶ RoHS compliant

![The image displays an icon of a white sheet of paper featuring faint gray horizontal lines across the lower section. A large, bold red checkmark is superimposed over the center of the document.](.nupro-935a-50-13060-1030-204-en/0869c2a0752f522e70e348c952fb983403d07796dd336055a1036f86167a5f78.jpg)
NOTE:

To purchase the optional DB-Audio2 daughter board, please contact your ADLINK sales representative.

# 1.3 Specifications

<table><tr><td colspan="2">System</td></tr><tr><td>CPU/Cache</td><td>Intel® CoreTM2 Quad, CoreTM2 Duo, Celeron® in LGA775 Socket</td></tr><tr><td>FSB</td><td>800/1066/1333 MHz</td></tr><tr><td>Chipset</td><td>Intel® 82Q35 Graphics Memory Controller HubIntel® ICH9 I/O Controller Hub</td></tr><tr><td>Memory</td><td>Two 240-pin DIMM sockets support 667/800MHz DDR2 (up to 4GB)</td></tr><tr><td>BIOS</td><td>AMI BIOS in 16-Mbit SPI Flash</td></tr><tr><td>Audio</td><td>Intel® High Definition Audio support via DB-Audio2 daughter board</td></tr><tr><td>Watch Dog Timer</td><td>1-255 second or 1-255 minute programmable and can generate system reset.</td></tr><tr><td>Hardware Monitor</td><td>CPU/System temperature, fan speed and onboard DC voltage</td></tr><tr><td>TPM</td><td>Infineon SLB 9635 TT 1.2 (NuPRO-935A/DV only)</td></tr><tr><td colspan="2">I/O Interfaces</td></tr><tr><td>IDE</td><td>One-channel UDMA 33, ATA-66/100 supportOne 40-pin IDE connector (1 device only)</td></tr><tr><td>Serial ATA</td><td>Two SATA ports, data rate up to 3 Gb/s</td></tr><tr><td>I/O Ports</td><td>1 USB 2.0 port on rear panel, four onboard2 Serial ports (one RS-232, one RS232/422/485/485+, by onboard pin-header)2 Gigabit Ethernet RJ45 ports (optional)1 VGA portPS/2 Keyboard/Mouse*1 Parallel port1 Floppy port</td></tr><tr><td>ISA</td><td>PCI-to-ISA Bridge: IT8888 (DMA not supported)</td></tr></table>

![The image displays a white icon of a document or sheet of paper featuring a folded top-right corner and faint gray horizontal lines running across the lower portion. A large, bold red checkmark is superimposed diagonally over the center of the paper.](.nupro-935a-50-13060-1030-204-en/1c3e45a5f82b69966870ffc3f1152c2f7c10e9e18294862507b30d847d09383d.jpg)
NOTE:

\* A Mini-DIN PS/2 KB/MS connector is not supported on boards with ordering numbers ending in "xx40" and higher. See "PS/2 Keyboard/Mouse Port" on page 14 for more information.

<table><tr><td colspan="2">Display</td></tr><tr><td>VGA</td><td>• GMA 3100 integrated in Q35 GMCH</td></tr><tr><td>VRAM</td><td>• Shared system memory up to 256 MB</td></tr><tr><td>CRT</td><td>• External Dsub-15 connector, resolution up to 2048 x 1536 @ 75 Hz</td></tr><tr><td colspan="2">Ethernet</td></tr><tr><td>Controller</td><td>• Intel® 82566DM and Intel® 82573L (NuPRO-935A/LV supports 82566DM only)</td></tr><tr><td>Ports</td><td>• Two RJ-45 Ethernet ports (NuPRO-935A/LV supports 1x GbE)</td></tr><tr><td colspan="2">Mechanical and Environment</td></tr><tr><td>Form Factor</td><td>• Standard full-size PICMG 1.0 SBC</td></tr><tr><td>Dimensions</td><td>• 338 x 122 mm (L x W)</td></tr><tr><td>Operating Temp.</td><td>• 0°C to 60°C</td></tr><tr><td>Storage Temp.</td><td>• -20°C to 80°C</td></tr><tr><td>Relative Humidity</td><td>• 5% to 90% non-condensing both operating and non-operating</td></tr><tr><td>Safety</td><td>• CE, FCC Class A</td></tr></table>

Table 1-1: NuPRO-935A General Specifications

# 1.4 Power Consumption

<table><tr><td colspan="2">Test Configuration</td></tr><tr><td>CPU</td><td>Intel® Core 2 Quad processor Q6600 2.40 GHz</td></tr><tr><td>Memory</td><td>Transcend DDR2 800 1GB x2</td></tr><tr><td>Graphics</td><td>Intel ® 82Q35 Graphics Memory controller</td></tr><tr><td>SATA Channel</td><td>Seagate ST3808110AS Barracuda 7200.9 80GB</td></tr><tr><td>Power Supply</td><td>COOLMAX FL-480ATX 450W</td></tr></table>

<table><tr><td colspan="5">DOS (idle)</td></tr><tr><td>Power Req.</td><td>+5V</td><td>+12V</td><td>CPU +12V</td><td>Total</td></tr><tr><td>Current (A)</td><td>3.37A</td><td>367.9mA</td><td>3.24A</td><td>—</td></tr><tr><td>Watts (W)</td><td>16.87W</td><td>4.42W</td><td>38.88</td><td>60.17W</td></tr><tr><td colspan="5">Windows XP, Idle</td></tr><tr><td>Power Req.</td><td>+5V</td><td>+12V</td><td>CPU +12V</td><td>Total</td></tr><tr><td>Current (A)</td><td>3.203A</td><td>233,6mA</td><td>1.578A</td><td>—</td></tr><tr><td>Watts (W)</td><td>16.02W</td><td>2.80W</td><td>18.94W</td><td>37.76W</td></tr><tr><td colspan="5">Windows XP, KPower</td></tr><tr><td>Power Req.</td><td>+5V</td><td>+12V</td><td>CPU +12V</td><td>Total</td></tr><tr><td>Current (A)</td><td>3.276A</td><td>533.0mA</td><td>7.616A</td><td>—</td></tr><tr><td>Watts (W)</td><td>16.38W</td><td>6.4W</td><td>91.39W</td><td>114.17W</td></tr><tr><td colspan="5">Windows XP, BurnIn Test 5.3</td></tr><tr><td>Power Req.</td><td>+5V</td><td>+12V</td><td>CPU +12V</td><td>Total</td></tr><tr><td>Current (A)</td><td>3.708A</td><td>555.1mA</td><td>5.728A</td><td>—</td></tr><tr><td>Watts (W)</td><td>18.54W</td><td>6.66W</td><td>68.74W</td><td>93.94W</td></tr></table>

# 1.5 Block Diagram

![Based on the provided diagram, here is the accurate description of the blocks and connections:\n\n**Central Processing Unit (CPU)**\n*   **Block:** 'CPU' containing text: 'Core™2 Quad/Duo Celeron®', 'LGA775 package', '800/1066/1333 MHz FSB', 'Dual-Core Hyper-Threading'.\n*   **Connection:** A double-headed arrow labeled '800/1066/1333 MHz FSB' connects the CPU to the Northbridge.\n\n**Northbridge**\n*   **Block:** 'Northbridge' containing text: 'Intel® Q35 GMCH'.\n*   **Connection:** A single line connects the Northbridge to the block 'CRT' (containing text 'DB-15').\n*   **Connection:** A double-headed arrow labeled 'DDR Channel A' connects the Northbridge to the block 'DIMM x2'. The text 'DDRII 667/800 MHz' is adjacent to this connection.\n*   **Connection:** A double-headed arrow labeled 'DDR Channel B' connects the Northbridge to the block 'DIMM x2'.\n*   **Connection:** A double-headed arrow labeled 'DMI Interface 2 GB/s' connects the Northbridge to the Southbridge.\n\n**Southbridge**\n*   **Block:** 'Southbridge' containing text: 'Intel® ICH9'. Inside the box are dotted outlines for internal controllers: 'SATA', 'PCIe Controller', 'USB 2.0', 'PCI Controller', 'LPC', 'SPI', and 'HD Codec'.\n*   **Left Connections:** Three double-headed arrows connect to external blocks:\n    *   'JMicron JMB20330 SATA to IDE Controller'\n    *   'SATA ports x2'\n    *   'USB 2.0 (Bracket x1, Internal x4)'\n*   **Right Connections:**\n    *   From 'PCIe Controller': A double-headed arrow labeled 'PCIe x1' connects to 'Intel 82566DM RJ-45'.\n    *   From 'PCIe Controller': A double-headed arrow labeled 'PCIe x1' connects to 'Intel 82573L RJ-45 (DV only)'.\n    *   From 'PCI Controller': A double-headed arrow labeled 'PCI Bus' connects to 'PCI 32-bit/ 33MHz bus'.\n    *   A double-headed arrow connects 'PCI 32-bit/ 33MHz bus' to 'IT8888G ISA Bridge'.\n    *   A double-headed arrow connects 'IT8888G ISA Bridge' to 'ISA bus'.\n*   **Bottom/Other Connections:**\n    *   From 'LPC': A double-headed arrow connects to 'TPM (DV only)'.\n    *   From 'LPC': A double-headed arrow connects to 'ITE8718 LPC Super I/O'.\n    *   From 'SPI': An arrow connects to 'SPI BIOS'.\n    *   From 'HD Codec': An arrow connects to 'Header for DB-Audio2'.\n    *   From the bottom edge of the Southbridge block: An arrow connects to 'Hardware Monitor'.\n\n**ITE8718 LPC Super I/O**\n*   **Block:** 'ITE8718 LPC Super I/O'.\n*   **Connections:** Four single lines connect to the left side of this block:\n    *   'KB/Mouse'\n    *   'LPT/FDD'\n    *   'RS-232'\n    *   'RS-232/ 422/485/ 485+'](.nupro-935a-50-13060-1030-204-en/5ea856d4f769b172d3bf12e770ecad6891f0216d009d5da1a4bab7b09f3941ca.jpg)

Figure 1-1: NuPRO-935A Block Diagram

# 1.6 Functional Description

# Processor Support

The NuPRO-935A is a single processor design for the latest Intel Yorkfield/Wolfdale/Conroe Processor family, starting from 1.8 GHz core frequency with future option up to 3.0 GHz. With one LGA775 socket, the CPU connects with Intel Q35 MCH through the 800/1066/1333 MHz Front Side Bus (FSB).

# Intel® Q35 + ICH9 Express chipset

The Intel® Q35 Express chipset provides the vital interfaces for the SBC. The Intel® Q35 comes with purpose-built capabilities designed specifically to address the key needs of the industrial computing environment and delivers improved system performance and comes with the integrated Intel® Graphics Media Accelerator 3100 engine that promotes advanced 3D, 2D, and video capabilities and cost-effective system building. The chipset also supports high-bandwidth interfaces including as PCI Express®, Serial ATA, and USB 2.0, as well as dual-channel DDR2 system memory.

# Intel® Graphics Media Accelerator 3100

The Intel® Graphics Media Accelerator (GMA) 3100 revolutionizes integrated graphics with new capabilities that provide significant increase in graphics performance. With support for DirectX 9 hardware acceleration, core frequency of 400 MHz, and up to 256 MB of video memory, the Intel GMA 3100 provides a cost-effective and high-performance graphics solution.

# Dual-channel DDR2 memory

To meet the requirements of memory-intensive applications, the NuPRO-935A has a dual-channel memory architecture supporting DDR2 667/800 MHz DIMMs. The high-bandwidth memory specification, meets the requirements of the latest 3D graphics, multimedia, and network application, and boosts system performance by eliminating bottlenecks.

# Gigabit Ethernet

The NuPRO-935A uses two Gigabit Ethernet controllers (Intel® 82566DM, 82573L) connected to the PCI-E x1 bus of the ICH9.82566DM is a single port Gigabit Ethernet Physical Layer Transceiver (PHY) that connects to its MAC through a dedicated interconnects. Both 82566DM and 82573L support operation at data rates of 10/100/1000 Mbps. Utilizing its wide bandwidth, the Gigabit LAN controller allows up to 1 Gbps of data transfer rate for superior network communications.

# Serial ATA II technology

Storage is efficient and secure with the Serial ATA II interface. Utilizing the Intel® ICH9, the NUPRO-935A supports up to two Serial ATA II devices capable of reading/writing data at up to 3 Gbps. The SATA specification improves chassis airflow via thinner and more flexible cables with lower pin count.

# Universal Serial Bus (USB) 2.0

The NUPRO-935A incorporates the Universal Serial Bus (USB) 2.0 specification that increases peripheral connection speed from 12 Mbps (USB 1.1) to 480 Mbps. USB 2.0 is backward compatible with USB 1.1.

# Hardware monitoring

A built-in, proactive hardware monitoring system in the ASIC monitors the CPU temperature, system fan rotations, and voltage levels to prevent overheating and/or component damage, effect timely failure detection, and ensure stable supply of current for critical components.

# Watchdog Timer

The watchdog timer (WDT) monitors system operations based on user-defined configurations. The WDT can be programmed for different time-out periods, such as from 1 to 255 seconds or from 1 to 255 minutes. The WDT generates a reset signal, then a reset request, after failure to strobe it within the programmed time period. A register bit may be enabled to indicate if the watchdog timer caused the reset event. The WDT register is cleared during the power-on sequence to enable the operating system to take appropriate action when the watchdog generates a reboot.

# Trusted Platform Module

The NuPRO-935A optionally supports TPM ver. 1.2 (Trusted Platform Module) for secure storage of keys, passwords and digital certificates. Systems supporting TPM offer improved hardware-based security in numerous applications, such as file and folder encryption, local password management, S-MIME e-mail, VPN and PKI authentication and wireless authentication for 802.1x and LEAP.

# 1.7 Mechanical Drawing

![117,92\n4,92\n9,82\n27,43\n337,82\n215,97\n4,50\n118,62\n4,92\n121,92](.nupro-935a-50-13060-1030-204-en/36943d95177bd613572f7a4596a7624946d0241892127b361ffe7fed8078996b.jpg)

Figure 1-2: NuPRO-935A Board Dimensions (top view)

# 1.8 I/O Connectivity

<table><tr><td>I/O</td><td>Bracket</td><td>Onboard</td><td>Golden Finger</td><td>Remarks</td></tr><tr><td>USB1</td><td>Y</td><td>—</td><td>—</td><td></td></tr><tr><td>VGA</td><td>Y</td><td>—</td><td>—</td><td>DB-15</td></tr><tr><td>GbE1 (RJ-45)</td><td>Y (with LED indication)</td><td>—</td><td>—</td><td>Act/Link/Speed</td></tr><tr><td>GbE2 (RJ-45)</td><td>Y (with LED indication)</td><td>—</td><td>—</td><td>Act/Link/Speed</td></tr><tr><td>PS/2 KB/MS1*</td><td>Y</td><td>—</td><td>—</td><td>—</td></tr><tr><td>KB/MS</td><td>—</td><td>Y</td><td>—</td><td>2.54 pitch</td></tr><tr><td>USB2/3</td><td>—</td><td>Y</td><td>—</td><td>2.54 pitch</td></tr><tr><td>USB4/5</td><td>—</td><td>Y</td><td>—</td><td>2.54 pitch</td></tr><tr><td>COM1/2</td><td>—</td><td>Y</td><td>—</td><td>2.54 pitch</td></tr><tr><td>Printer port</td><td>—</td><td>Y</td><td>—</td><td>—</td></tr><tr><td>IDE</td><td>—</td><td>Y</td><td>—</td><td>—</td></tr><tr><td>Floppy</td><td>—</td><td>Y</td><td>—</td><td>—</td></tr><tr><td>SATA-300 1/2</td><td>—</td><td>Y</td><td>—</td><td>—</td></tr><tr><td>ISA</td><td>—</td><td>—</td><td>Y</td><td>—</td></tr><tr><td>PCI 32-bit/33 MHz</td><td>—</td><td>—</td><td>Y</td><td>4 slots</td></tr></table>

![The image shows a white icon of a piece of paper with faint grey horizontal lines. A large, bold red checkmark is superimposed over the document, running diagonally from the bottom left to the top right. The top right corner of the paper is slightly curled.](.nupro-935a-50-13060-1030-204-en/ea8c1fb92d712499a9f8e876613750618cf598e9e6cd58dc151d2a23e349c3db.jpg)
NOTE:

\* Not supported on boards with ordering numbers ending in "xx40" and higher. See "PS/2 Keyboard/Mouse Port" on page 14 for more information.

# 1.9 Package Contents

Before unpacking, check the shipping carton for any damage. If the shipping carton and/or contents are damaged, inform your dealer immediately. Retain the shipping carton and packing materials for inspection. Obtain authorization from the dealer before returning any product to ADLINK.

▶ NuPRO-935A
▶ SATA cable x2
▶ SATA Power cable x1
▶ 2-port USB cable with bracket x1
▶ COM+Print cable with bracket x1
▶ COM cable with bracket x1
▶ PS/2 Y cable x1\*
▶ IDE cable x1\*
▶ Floppy cable x1\*
▶ ADLINK All-in-One Driver DVD
▶ User's manual

![The image displays a digital icon of a document. It features a white piece of paper with a folded top-left corner and faint horizontal lines running down the center. A large, bold red checkmark is superimposed over the center of the document, slanting upwards from left to right.](.nupro-935a-50-13060-1030-204-en/087bd93a1bbea720853cca94494bbb4d123f1775759e5983b7e4bf2cae9a1277.jpg)
NOTE:

\* Not included with ordering numbers ending in "xx40" and higher. See "PS/2 Keyboard/Mouse Port" on page 14 for more information.

![The image displays a cropped, red triangular warning sign. In the center is a white exclamation point.](.nupro-935a-50-13060-1030-204-en/db6d5894d9dfc3e85091129f828ffdd0168d6fb4735bf95b48938978668600c2.jpg)
WARNING:

The NuPRO-935A must be protected from static discharge and physical shock. Never remove any of the socketed parts except at a static-free workstation. Use the anti-static bag shipped with the product to handle the board. Wear a grounded wrist strap when installing and/or servicing.

This page intentionally left blank.

# 2 Hardware Information

This chapter provides information on the NuPRO-935A board layout, connector pin assignments, and jumper settings.

# 2.1 Rear Panel I/O Ports

![Diagram of an Ethernet cable connector with labeled ports and connectors](.nupro-935a-50-13060-1030-204-en/734e18b947c72e35d76d1dbee9409dbc973c95039550514b90b8fe58d774baec.jpg)

Figure 2-1: Rear Panel I/O Ports

<table><tr><td></td><td>Connector</td><td>Description</td></tr><tr><td>1</td><td>PS/2 KB/MS port</td><td>Connects a PS/2 mouse and keyboard $^{1}$ </td></tr><tr><td>2</td><td>Gigabit LAN port (RJ-45)</td><td>Provides Gigabit Ethernet connection</td></tr><tr><td>3</td><td>Gigabit LAN port (RJ-45)</td><td>Provides Gigabit Ethernet connection (not supported on NuPRO-935A/LV)</td></tr><tr><td>4</td><td>VGA port</td><td>This 15-pin port connects to a CRT or LCD monitor.</td></tr><tr><td>5</td><td>USB 2.0 port</td><td>High-speed USB ports available for connecting USB devices</td></tr></table>

![The image displays a white document icon featuring a folded top-right corner and faint horizontal lines suggesting text. A large, bold red checkmark is superimposed over the center of the document. There is no actual text present in the image.](.nupro-935a-50-13060-1030-204-en/047f42b9a38d17f9f7924f68b2bde4f608217532c4823daf17ea6b39e7160446.jpg)
NOTE:

$^{1}$ A Mini-DIN PS/2 KB/MS connector is not supported on boards with ordering numbers ending in “xx40” and higher. See “PS/2 Keyboard/Mouse Port” below.

# PS/2 Keyboard/Mouse Port

![6\n4\n5\n3\n2 1](.nupro-935a-50-13060-1030-204-en/d29d27dabe91345bd573882016856be02f8653c8f20d6afb15fe59d5c4c74334.jpg)

<table><tr><td>Pin #</td><td>Signal</td><td>Function</td></tr><tr><td>1</td><td>KBDAT</td><td>Keyboard Data</td></tr><tr><td>2</td><td>MSDAT</td><td>Mouse Data</td></tr><tr><td>3</td><td>GND</td><td>Ground</td></tr><tr><td>4</td><td>KBMS5V</td><td>Power</td></tr><tr><td>5</td><td>KBCLK</td><td>Keyboard Clock</td></tr><tr><td>6</td><td>MSCLK</td><td>Mouse Clock</td></tr></table>

For boards without a Mini-DIN PS/2 KB/MS connector, customers wishing to use a PS/2 type keyboard and mouse may purchase a PS/2 cable with bracket (P/N: 30-01019-2000) which connects to the External Keyboard/Mouse Connector (CN19).

![Close-up of a beige computer tower with two blue connectors and two black connectors (no text or symbols visible)](.nupro-935a-50-13060-1030-204-en/a634f433705a1c450112b3dc102614d2c66790463cdc297adfa7d30e67caaa41.jpg)

# PS/2 Mouse Port on bracket (green)

![6\n4\n5\n3\n2 1](.nupro-935a-50-13060-1030-204-en/fcf2947fa74a668d21895edf7da2ba86eb34da67f7b953217a42010081743bae.jpg)

<table><tr><td>Pin #</td><td>Signal</td><td>Function</td></tr><tr><td>1</td><td>MSDATA</td><td>Mouse Data</td></tr><tr><td>2</td><td>NC</td><td>not connected</td></tr><tr><td>3</td><td>GND</td><td>Ground</td></tr><tr><td>4</td><td>+5V</td><td>Power</td></tr><tr><td>5</td><td>CLK</td><td>Clock</td></tr><tr><td>6</td><td>NC</td><td>not connected</td></tr></table>

# PS/2 Keyboard Port on bracket (purple)

![6\n4\n5\n3\n2 1](.nupro-935a-50-13060-1030-204-en/b4c00a119d351b176c07832977dd0b182da9256dbcde1d654ec7563a64e3ff73.jpg)

<table><tr><td>Pin #</td><td>Signal</td><td>Function</td></tr><tr><td>1</td><td>KBDATA</td><td>Keyboard Data</td></tr><tr><td>2</td><td>NC</td><td>not connected</td></tr><tr><td>3</td><td>GND</td><td>Ground</td></tr><tr><td>4</td><td>+5V</td><td>Power</td></tr><tr><td>5</td><td>CLK</td><td>Clock</td></tr><tr><td>6</td><td>NC</td><td>not connected</td></tr></table>

# LAN (RJ-45) Ports

![Green LED\nAmber/Green LED](.nupro-935a-50-13060-1030-204-en/b49c5d711cb3e4a683de667c1a83051aa05b353c1745f657bb73b87d09ac6ca2.jpg)

<table><tr><td>Pin #</td><td>10BASE-T/100BASE-TX</td><td>1000BASE-T</td></tr><tr><td>1</td><td>TX+</td><td>BI_DA+</td></tr><tr><td>2</td><td>TX-</td><td>BI_DA-</td></tr><tr><td>3</td><td>RX+</td><td>BI_DB+</td></tr><tr><td>4</td><td>--</td><td>BI_DC+</td></tr><tr><td>5</td><td>--</td><td>BI_DC-</td></tr><tr><td>6</td><td>RX-</td><td>BI_DB-</td></tr><tr><td>7</td><td>--</td><td>BI_DD+</td></tr><tr><td>8</td><td>--</td><td>BI_DD-</td></tr></table>

Refer to the table below for the LAN port LED indications.

<table><tr><td colspan="2">ACT/LINK LED</td><td colspan="2">SPEED LED</td></tr><tr><td>Status</td><td>Description</td><td>Status</td><td>Description</td></tr><tr><td>Off</td><td>No Link</td><td>Off</td><td>10 Mb connection</td></tr><tr><td>Green</td><td>Linked</td><td>Amber</td><td>100 Mb connection</td></tr><tr><td>Blinking</td><td>Data Activity</td><td>Green</td><td>1 Gb connection</td></tr></table>

# USB Connector

![4\n3\n2\n1](.nupro-935a-50-13060-1030-204-en/594a7c2100851503096a7f0933aaeb2e0c13c5683fe8a6a22d123210d2a74252.jpg)

<table><tr><td>Pin #</td><td>Signal Name</td></tr><tr><td>1</td><td>Vcc</td></tr><tr><td>2</td><td>Data-</td></tr><tr><td>3</td><td>Data+</td></tr><tr><td>4</td><td>GND</td></tr></table>

# VGA Port

![10\n5\n15\n11\n6\n1](.nupro-935a-50-13060-1030-204-en/617103fcacc495f40f08b5dba66e8b40f7f6dc8168c372d8e8e29c02a0fbafb2.jpg)

<table><tr><td>Pin #</td><td>Signal</td></tr><tr><td>1</td><td>Red</td></tr><tr><td>2</td><td>Green</td></tr><tr><td>3</td><td>Blue</td></tr><tr><td>4</td><td>NC</td></tr><tr><td>5</td><td>Ground</td></tr><tr><td>6</td><td>Ground</td></tr><tr><td>7</td><td>Ground</td></tr><tr><td>8</td><td>Ground</td></tr><tr><td>9</td><td>+5 V</td></tr><tr><td>10</td><td>Ground</td></tr><tr><td>11</td><td>NC</td></tr><tr><td>12</td><td>DDC DAT</td></tr><tr><td>13</td><td>HSYNC</td></tr><tr><td>14</td><td>VSYNC</td></tr><tr><td>15</td><td>DDC CLK</td></tr></table>

# 2.2 Board Layout

The illustrations below show the locations of connectors, slots, and jumpers on the NuPRO-935A.

![Diagram of a computer motherboard layout with numbered components for identification](.nupro-935a-50-13060-1030-204-en/a8763fd1ddee3dbd7c7403c4d54cef3e7ebf78e1169f24ea0f2a39ae6e90fddb.jpg)

Figure 2-2: Connectors and Jumpers Pt. 1

<table><tr><td></td><td>Connector</td><td>Description</td></tr><tr><td>1</td><td>DIMM1</td><td>240-pin DDR2 DIMM slot</td></tr><tr><td>2</td><td>DIMM2</td><td>240-pin DDR2 DIMM slot</td></tr><tr><td>3</td><td>CN1</td><td>System Panel connector</td></tr><tr><td>4</td><td>CN7</td><td>ATX 12V Power connector</td></tr><tr><td>5</td><td>FAN1</td><td>System Fan connector</td></tr><tr><td>6</td><td>FAN2</td><td>CPU Fan connector</td></tr><tr><td>7</td><td>JP5</td><td>Clear CMOS</td></tr><tr><td>8</td><td>CN17</td><td>LPC port connector</td></tr><tr><td>9</td><td>CN19</td><td>External Keyboard/Mouse connector</td></tr></table>

![Diagram of an electronic device layout with numbered components and connectors](.nupro-935a-50-13060-1030-204-en/b356db9ae3c5302b9eb4b9ac78d85061bf2282ca7d606b0500eb265300ab229d.jpg)

Figure 2-3: Connectors and Jumpers Pt. 2

<table><tr><td></td><td>Connector</td><td>Description</td></tr><tr><td>10</td><td>CN4</td><td>HD Audio Daughter Board connector</td></tr><tr><td>11</td><td>CN5</td><td>COM2 connector</td></tr><tr><td>12</td><td>CN6</td><td>COM1 connector</td></tr><tr><td>13</td><td>CN2</td><td>Serial ATA connector</td></tr><tr><td>14</td><td>CN3</td><td>Serial ATA connector</td></tr><tr><td>15</td><td>CN8</td><td>Floppy port connector</td></tr><tr><td>16</td><td>CN10</td><td>IDE connector</td></tr><tr><td>17</td><td>CN11</td><td>USB1 pin header</td></tr><tr><td>18</td><td>CN12</td><td>USB2 pin header</td></tr><tr><td>19</td><td>CN13</td><td>LPT connector</td></tr><tr><td>20</td><td>JP1</td><td>COM1 mode jumper</td></tr><tr><td>21</td><td>JP2</td><td>COM1 mode jumper</td></tr><tr><td>22</td><td>JP3</td><td>COM1 mode jumper</td></tr><tr><td>23</td><td>JP4</td><td>COM1 mode jumper</td></tr></table>

# 2.3 Onboard Connectors

# ATX 12V Power Connector (CN7)

![2\n1\n4\n3](.nupro-935a-50-13060-1030-204-en/b91bff30a71d12643a95eb1cc36064133dca80e755e7c8c6e4e6c900e6178c56.jpg)

<table><tr><td>Pin #</td><td>Signal</td></tr><tr><td>1</td><td>GND</td></tr><tr><td>2</td><td>GND</td></tr><tr><td>3</td><td>+12V DC</td></tr><tr><td>4</td><td>+12V DC</td></tr></table>

![The image displays a digital icon of a white document or piece of paper with a folded top-right corner. Faint horizontal gray lines run across the paper, suggesting written text. Superimposed over the document is a large, bold, red checkmark (or tick mark) angled upward from left to right. There is no text present in the image.](.nupro-935a-50-13060-1030-204-en/beb0c7879ec5dd4d76aaf02d6614cf6def6e9625515af0b80f9856135cfbd41d.jpg)
NOTE:

The ATX 12V power connector must be connected to provide sufficient power to the SBC in either ATX or AT modes. See “Installing the Power Connectors” on page 34.

# CPU Fan Connector (FAN2)

![The image displays a black and white line drawing of a slot machine centered between the number 4 on the left and the number 1 on the right. The slot machine icon is a rectangular outline featuring a horizontal rectangle at the top and four smaller squares arranged in a row near the bottom.](.nupro-935a-50-13060-1030-204-en/7ad5ea5b012a98b4feaabee588004d875c1e86ab82627c52df412a9bbad97b66.jpg)

<table><tr><td>Pin #</td><td>Signal</td></tr><tr><td>1</td><td>GND</td></tr><tr><td>2</td><td>Fan power (+12V)</td></tr><tr><td>3</td><td>Fan Tachometer</td></tr><tr><td>4</td><td>Fan Speed Control</td></tr></table>

# System Fan Connector (FAN1)

![The image features a line drawing of a simplified building or house icon centered between the number '3' on the left and the number '1' on the right. The central icon depicts a rectangular structure with a smaller rectangle on top, containing three small squares arranged horizontally inside the main rectangle.](.nupro-935a-50-13060-1030-204-en/3147094b57af1e4c8ede00ffc3feeb54fd032a47acd0319fe1ea9c41f7b488cb.jpg)

<table><tr><td>Pin #</td><td>Signal</td></tr><tr><td>1</td><td>GND</td></tr><tr><td>2</td><td>Fan power (+12V)</td></tr><tr><td>3</td><td>Fan Tachometer</td></tr></table>

# IDE Connector (CN10)

![1\n2\n39\n40](.nupro-935a-50-13060-1030-204-en/e49103357fc190185d9c4be285a795dc214271c6a775322709ba6bb629a0d33a.jpg)

<table><tr><td>Pin #</td><td>Signal</td><td>Pin #</td><td>Signal</td></tr><tr><td>1</td><td>Reset IDE</td><td>2</td><td>Ground</td></tr><tr><td>3</td><td>Host data 7</td><td>4</td><td>Host data 8</td></tr><tr><td>5</td><td>Host data 6</td><td>6</td><td>Host data 9</td></tr><tr><td>7</td><td>Host data 5</td><td>8</td><td>Host data 10</td></tr><tr><td>9</td><td>Host data 4</td><td>10</td><td>Host data 11</td></tr><tr><td>11</td><td>Host data 3</td><td>12</td><td>Host data 12</td></tr><tr><td>13</td><td>Host data 2</td><td>14</td><td>Host data 13</td></tr><tr><td>15</td><td>Host data 1</td><td>16</td><td>Host data 14</td></tr><tr><td>17</td><td>Host data 0</td><td>18</td><td>Host data 15</td></tr><tr><td>19</td><td>Ground</td><td>20</td><td>NC</td></tr><tr><td>21</td><td>DRQ0 / DRQ1</td><td>22</td><td>Ground</td></tr><tr><td>23</td><td>Host IOW</td><td>24</td><td>Ground</td></tr><tr><td>25</td><td>Host IOR</td><td>26</td><td>Ground</td></tr><tr><td>27</td><td>IOCHRDY</td><td>28</td><td>Host ALE</td></tr><tr><td>29</td><td>DACK0 / DACK1</td><td>30</td><td>Ground</td></tr><tr><td>31</td><td>IRQ14 / IRQ 15</td><td>32</td><td>No connect</td></tr><tr><td>33</td><td>Address 1</td><td>34</td><td>No connect</td></tr><tr><td>35</td><td>Address 0</td><td>36</td><td>Address 2</td></tr><tr><td>37</td><td>Chip select 0</td><td>38</td><td>Chip select 1</td></tr><tr><td>39</td><td>Activity</td><td>40</td><td>Ground</td></tr></table>

# Floppy disk drive connector (CN8)

![1\n2\n33\n34](.nupro-935a-50-13060-1030-204-en/bbf8e6051853d3e0e75266260668e73aab4f27c4505a729650ac9a61630e01ac.jpg)

<table><tr><td>Pin #</td><td>Signal</td><td>Pin #</td><td>Signal</td></tr><tr><td>1</td><td>GND</td><td>2</td><td>Extended Density</td></tr><tr><td>3</td><td>GND</td><td>4</td><td>NC</td></tr><tr><td>5</td><td>NC</td><td>6</td><td>NC</td></tr><tr><td>7</td><td>GND</td><td>8</td><td>Index</td></tr><tr><td>9</td><td>GND</td><td>10</td><td>Motor A Select</td></tr><tr><td>11</td><td>GND</td><td>12</td><td>NC</td></tr><tr><td>13</td><td>GND</td><td>14</td><td>Drive A Select</td></tr><tr><td>15</td><td>GND</td><td>16</td><td>NC</td></tr><tr><td>17</td><td>GND</td><td>18</td><td>Step Direction</td></tr><tr><td>19</td><td>GND</td><td>20</td><td>Step Pulse</td></tr><tr><td>21</td><td>GND</td><td>22</td><td>Write Data</td></tr><tr><td>23</td><td>GND</td><td>24</td><td>Write Gate</td></tr><tr><td>25</td><td>GND</td><td>26</td><td>Track 0</td></tr><tr><td>27</td><td>GND</td><td>28</td><td>Write Protect</td></tr><tr><td>29</td><td>GND</td><td>30</td><td>Read Data</td></tr><tr><td>31</td><td>GND</td><td>32</td><td>Side 1</td></tr><tr><td>33</td><td>GND</td><td>34</td><td>Disk Change</td></tr></table>

# Parallel Port (CN13)

![1\n14\n13\n26](.nupro-935a-50-13060-1030-204-en/fa0d1ebacb8bf7d408882a96f2c5ae0a95101d8cb5f7e587b4253d7925d3e6bb.jpg)

<table><tr><td>Pin #</td><td>Signal</td><td>Pin #</td><td>Signal</td></tr><tr><td>1</td><td>Line Printer Strobe</td><td>14</td><td>Auto-Feed</td></tr><tr><td>2</td><td>Parallel Data 0</td><td>15</td><td>Error</td></tr><tr><td>3</td><td>Parallel Data 1</td><td>16</td><td>Initialize</td></tr><tr><td>4</td><td>Parallel Data 2</td><td>17</td><td>Select</td></tr><tr><td>5</td><td>Parallel Data 3</td><td>18</td><td>Ground</td></tr><tr><td>6</td><td>Parallel Data 4</td><td>19</td><td>Ground</td></tr><tr><td>7</td><td>Parallel Data 5</td><td>20</td><td>Ground</td></tr><tr><td>8</td><td>Parallel Data 6</td><td>21</td><td>Ground</td></tr><tr><td>9</td><td>Parallel Data 7</td><td>22</td><td>Ground</td></tr><tr><td>10</td><td>Acknowledge</td><td>23</td><td>Ground</td></tr><tr><td>11</td><td>Busy</td><td>24</td><td>Ground</td></tr><tr><td>12</td><td>Paper Empty</td><td>25</td><td>Ground</td></tr><tr><td>13</td><td>Select</td><td>26</td><td>NC</td></tr></table>

# HD Audio Daughter Board Connector (CN4)

![2\n10\n1\n9](.nupro-935a-50-13060-1030-204-en/bec60d0f7f74f89541688d7a794e576758e7a1aa1c6e62ca8cfccb94f695ca88.jpg)

<table><tr><td>Pin #</td><td>Signal</td><td>Function</td></tr><tr><td>1</td><td>GND</td><td>Ground</td></tr><tr><td>2</td><td>AUD_BCLK</td><td>Audio Clock</td></tr><tr><td>3</td><td>GND</td><td>Ground</td></tr><tr><td>4</td><td>ICH_AUD_SDIN0</td><td>Audio Data Input</td></tr><tr><td>5</td><td>P5V</td><td>+ 5V</td></tr><tr><td>6</td><td>ICH_AUD_SDOUT</td><td>Audio Data Output</td></tr><tr><td>7</td><td>P5V_AUD</td><td>+ 5V</td></tr><tr><td>8</td><td>P3V3_DVDD</td><td>3.3V</td></tr><tr><td>9</td><td>AUD_SYNC</td><td>Audio Synchronous</td></tr><tr><td>10</td><td>AUD_RST-L</td><td>Audio Reset</td></tr></table>

![The image displays an icon of a document. It features a white sheet of paper with thin horizontal grey lines and a folded top-left corner. A large, bold red checkmark is superimposed over the center of the document.](.nupro-935a-50-13060-1030-204-en/44f3c78affe261e397d02de2feb19df60318a9b477e8a5eb782e669b4c282925.jpg)
NOTE:

This connector is designed for use with the ADLINK DB-Audio2 daughter board.

# COM1 Connector (RS-422/485/485+) (CN6)

![2\n10\n1\n9](.nupro-935a-50-13060-1030-204-en/bafc70aece5526e2d2e9c4c9f051df92789af3d40e541d6cbbe1f79dfa17432e.jpg)

<table><tr><td>Pin #</td><td>Signal</td><td>Functions</td></tr><tr><td>1</td><td>TX-</td><td>Transmit (-)</td></tr><tr><td>2</td><td>NC</td><td>Not Connected</td></tr><tr><td>3</td><td>TX+</td><td>Transmit (+)</td></tr><tr><td>4</td><td>NC</td><td>Not Connected</td></tr><tr><td>5</td><td>RX+</td><td>Receive (+)</td></tr><tr><td>6</td><td>NC</td><td>Not Connected</td></tr><tr><td>7</td><td>RX-</td><td>Receive (-)</td></tr><tr><td>8</td><td>NC</td><td>Not Connected</td></tr><tr><td>9</td><td>GND</td><td>Ground</td></tr><tr><td>10</td><td>NC</td><td>Not Connected</td></tr></table>

Note: See Section 2.4 for COM1 mode jumper settings.

# COM1/COM2 Connector (RS-232) (CN5/6)

![2\n10\n1\n9](.nupro-935a-50-13060-1030-204-en/2946334cc11b903eebf80d44aee795880040e48ea791b3de1bf5c0f19ac0f1cc.jpg)

<table><tr><td>Pin #</td><td>Signal</td><td>Functions</td></tr><tr><td>1</td><td>DCD</td><td>Data Carrier Detect</td></tr><tr><td>2</td><td>DSR</td><td>Data Set Ready</td></tr><tr><td>3</td><td>RXD</td><td>Receive Data</td></tr><tr><td>4</td><td>RTS</td><td>Request to Send</td></tr><tr><td>5</td><td>TXD</td><td>Transmit Data</td></tr><tr><td>6</td><td>CTS</td><td>Clear to Send</td></tr><tr><td>7</td><td>DTR</td><td>Data Terminal Ready</td></tr><tr><td>8</td><td>RI</td><td>Ring Indicate</td></tr><tr><td>9</td><td>GND</td><td>Ground</td></tr><tr><td>10</td><td>NC</td><td>No Connect</td></tr></table>

# USB 2.0 Connector (CN11-12)

![2\n10\n1](.nupro-935a-50-13060-1030-204-en/e2019076dfe66d8fc88d80e14700c2498f8dc1c5f898cfd53be45c269972c13c.jpg)

<table><tr><td>Pin #</td><td>Signal</td><td>Pin #</td><td>Signal</td></tr><tr><td>1</td><td>+5V</td><td>2</td><td>+5V</td></tr><tr><td>3</td><td>USB0-</td><td>4</td><td>USB1-</td></tr><tr><td>5</td><td>USB0+</td><td>6</td><td>USB01+</td></tr><tr><td>7</td><td>GND</td><td>8</td><td>GND</td></tr><tr><td>9</td><td>Key</td><td>10</td><td>NC</td></tr></table>

# External Keyboard/Mouse Connector (CN19)

![The image displays a 2x2 grid of black squares on a white background. Inside each black square are two small white rectangles arranged vertically. The numbers '5', '1', '6', and '2' appear in the top-left, top-right, bottom-left, and bottom-right corners respectively.](.nupro-935a-50-13060-1030-204-en/76bb647c72832cc4c967d093f2b464172715e5f6c9c1c0e7d41f466c126858c6.jpg)

<table><tr><td>Pin #</td><td>Signal</td><td>Function</td></tr><tr><td>1</td><td>KDAT</td><td>Keyboard data</td></tr><tr><td>2</td><td>KCLK</td><td>Keyboard clock</td></tr><tr><td>3</td><td>MDAT</td><td>Mouse data</td></tr><tr><td>4</td><td>MCLK</td><td>Mouse data</td></tr><tr><td>5</td><td>P5V_KM</td><td>+5 V</td></tr><tr><td>6</td><td>GND</td><td>Ground</td></tr></table>

For use with PS/2 cable with bracket (P/N: 30-01019-2000).

# Serial ATA Connectors (CN2-3)

![1\n7](.nupro-935a-50-13060-1030-204-en/cb4d84e8679573f3752c297b8fc8e1c13a9bf0b5ff7091c0b6e2ecba61f26a81.jpg)

<table><tr><td>Pin #</td><td>Signal</td></tr><tr><td>1</td><td>GND</td></tr><tr><td>2</td><td>TXP</td></tr><tr><td>3</td><td>TXN</td></tr><tr><td>4</td><td>GND</td></tr><tr><td>5</td><td>RXN</td></tr><tr><td>6</td><td>RXP</td></tr><tr><td>7</td><td>GND</td></tr></table>

# System Panel Connector (CN1)

Connects to chassis-mounted buttons, speakers, and LEDs.

<table><tr><td>Pin #</td><td>Signal</td><td>Function</td><td>Pin Group</td></tr><tr><td>1</td><td>P5V</td><td>Power for +5v</td><td rowspan="3">Power LED</td></tr><tr><td>2</td><td>NC</td><td></td></tr><tr><td>3</td><td>HC_PLED-</td><td>Power LED signal</td></tr><tr><td>4</td><td>NC</td><td></td><td rowspan="2"></td></tr><tr><td>5</td><td>GND</td><td>Ground</td></tr><tr><td>6</td><td>GND</td><td>Ground</td><td rowspan="5">ATX Power Connector</td></tr><tr><td>7</td><td>NC</td><td></td></tr><tr><td>8</td><td>ATX_PSO</td><td>Power-on signal for</td></tr><tr><td>9</td><td>P5V_SB_A</td><td>Power for +5v</td></tr><tr><td>10</td><td>PMEJ</td><td>Power control signal</td></tr><tr><td>11</td><td>HC_SPKR</td><td>Speaker signal</td><td rowspan="4">Chassis Speaker</td></tr><tr><td>12</td><td>NC</td><td></td></tr><tr><td>13</td><td>NC</td><td></td></tr><tr><td>14</td><td>P5V</td><td>Power for +5v</td></tr><tr><td>15</td><td>HC_RSTB</td><td>RESET signal</td><td rowspan="2">Reset Button</td></tr><tr><td>16</td><td>GND</td><td>Ground</td></tr><tr><td>17</td><td>HDLED_P</td><td>Hard Disk LED signal</td><td rowspan="2">Hard Disk LED</td></tr><tr><td>18</td><td>P5V</td><td>Power for +5v</td></tr><tr><td>19</td><td>HC_PBTNJ</td><td>Power-on signal</td><td rowspan="2">Power-on Button</td></tr><tr><td>20</td><td>GND</td><td>Ground</td></tr></table>

# 2.4 Jumpers

# COM1 mode Jumper Settings (JP1-4)

Short the jumper pins according to the following settings to set COM1 to RS-232/422/485/485+ mode

![The image displays a diagram of a 7-segment display with four vertical segments visible, arranged in a 2x2 grid. The segments are black rectangles with white square cutouts.\n\nSurrounding the segments are numbers:\n- Above the top-left segment is the number '5'.\n- Above the top-right segment is the number '1'.\n- Below the bottom-left segment is the number '6'.\n- Below the bottom-right segment is the number '2'.](.nupro-935a-50-13060-1030-204-en/59aa5a2efdcb7b54c66a53977b2a75ea9a94d77edd9acfd12eb462e0de05c432.jpg)

<table><tr><td>#</td><td>RS-232</td><td>RS-422</td><td>RS-485</td><td>RS-485+</td></tr><tr><td>JP1</td><td>1-3, 2-4</td><td>3-5, 4-6</td><td>3-5, 4-6</td><td>3-5, 4-6</td></tr><tr><td>JP2</td><td>1-3, 2-4</td><td>3-5, 4-6</td><td>3-5, 4-6</td><td>3-5, 4-6</td></tr><tr><td>JP3</td><td>1-2</td><td>3-4</td><td>5-6</td><td>5-6</td></tr><tr><td>JP4</td><td>-</td><td>1-3, 2-4</td><td>1-3, 2-4</td><td>3-5, 4-6</td></tr></table>

# Clear CMOS (JP5)

The CMOS RAM data contains the date / time and BIOS setting information. CMOS is powered by the onboard button cell battery. To erase the CMOS RAM data: (1) Unplug the NuPRO-935A (2) short the JP1 pin 2-3 (3) turn the power on. After power on, remove the jumper cap from pin 2-3 and reinstall it to pin 1-2.

This page intentionally left blank.

<table><tr><td>RTC status</td><td>Connection</td><td>JP5</td></tr><tr><td>Normal</td><td>1 – 2</td><td>&lt;img src="images/83b2b0ab8b0e01bc7a1050b203f96d33e37386d3e8072425e023a244d27b9c0c.jpg"/&gt;</td></tr><tr><td>Clear CMOS</td><td>2 – 3</td><td>&lt;img src="images/9ddcd62c91a51bdad2624811522e9079744504861fe4dbc58f1770d5e9750bf8.jpg"/&gt;</td></tr></table>

# 3 Getting Started

This chapter provides information on how to install components on the NuPRO-935A SBC.

# 3.1 Installing the CPU

The NuPRO-935A supports a single Intel® Core™2 Quad/Duo, Pentium® D, or Celeron® processor via the surface mount LGA775 socket (Socket T).

![The image displays a warning sign featuring a red triangle with a black outline. Inside the triangle is a white exclamation point. Below the triangle, the word 'WARNING' is written in black capital letters.](.nupro-935a-50-13060-1030-204-en/aa6789561d091ce3b2ef3f8ad66b340e7a7a5c6dda8df54dd102764bcfc788ad.jpg)

Disconnect all power supply to the board before installing a CPU to prevent damaging the board and CPU.

Do not touch socket contacts. Damaging the contacts voids the product warranty. Follow the installation instructions carefully to avoid damaging SBC components.

![Close-up of a computer processor with a red prohibition symbol (no text or symbols on the chip or background)](.nupro-935a-50-13060-1030-204-en/0a45790a5471bbcb4f80487e8dca0af47b08cc2c1354d57ec5edc86a27ba4b5c.jpg)

# To install the CPU:

1. Press the load lever (A), then disengage it from the retention tab (B).

![A\nB](.nupro-935a-50-13060-1030-204-en/f16d47c9724499b83237ef039cd2cc49ba49872567625e2db902e1330e113ecd.jpg)

2. Lift and rotate the load lever to a $135^{\circ}$ angle

![Close-up of a mechanical component with a red curved arrow indicating motion or force, no visible text or symbols.](.nupro-935a-50-13060-1030-204-en/74d782ea18897dafc6d8b81db966608fd1680aa58e56bdf8460ced40058e734d.jpg)

3. Lift the load plate to a $100^{\circ}$ angle using your thumb and forefinger

![Close-up of a hand holding an open computer processor with a red curved arrow indicating the process (no text or symbols visible)](.nupro-935a-50-13060-1030-204-en/088f7184ada7bb137d83e67ea83c69b251d259dcdddaefbd455ba445e57b3e14.jpg)

4. Use your thumb to push and remove the protective socket cover (plastic) from the load plate

![Close-up of a hand holding an open CPU socket with a red arrow pointing to its interior (no text or symbols visible)](.nupro-935a-50-13060-1030-204-en/0fda89ebf0305a9572570332c845a518a70c6f1d5673a31313997c439fee5d1a.jpg)

5. Position the CPU over the socket, then match the notches on the CPU side with the alignment keys on the socket. The golden triangle on the CPU must be positioned on the bottom-left corner of the socket.

![Notch\nGolden triangle\nAlignment key](.nupro-935a-50-13060-1030-204-en/b8efbac006053c46d37b3221c616f6267a9b1f814126cf19a7d449c7de108cca.jpg)

![The image displays a warning sign. It features a dark red triangle pointing upward with a white exclamation point centered inside it. Below the triangle, the word 'WARNING' appears in black, capital letters on a white background.](.nupro-935a-50-13060-1030-204-en/3ac9cc06042a4f60d874b6d9f3b00ac4a559cbf6fbd1429503774e924403b1b0.jpg)

The CPU fits the socket in only one orientation. DO NOT force it into the socket to avoid damaging it.

6. Carefully place the CPU on the socket in a vertical motion. The socket has tabs that accommodate your fingers during installation.

![Socket tab](.nupro-935a-50-13060-1030-204-en/4decee6e396ada2edab3a1c35dcec0a647aed0f2528d6108fb4c58c2eea7fd9f.jpg)

7. Close the load plate (A), then fasten the load lever on the retention tab (B).

![Close-up of a computer processor casing with red arrows indicating internal components (no text or symbols)](.nupro-935a-50-13060-1030-204-en/290778f9a4c26ca2c29703957f6e59e25147df18413ee28a6a7d4c87f6471e00.jpg)

# 3.2 Installing the CPU Fan and Heatsink

![A vertical image showing a yellow triangular warning sign with a black border. Inside the triangle is a large black exclamation point. Below the triangle, the word 'CAUTION:' is written in black capital letters on a white background.](.nupro-935a-50-13060-1030-204-en/a0f0f6994e5e8e0ae68436a61d91d6cab5b33e40b83d0c9404c9235c1ae1b9c0.jpg)

The CPU requires a chassis with an airflow inlet and maximum internal ambient temperature of $60^{\circ}$ C. A especially-designed CPU fan and heatsink must be installed before using the SBC. Failure to install a CPU fan and heatsink may damage the system host board and/or the CPU.

The following CPU fan and heatsink assemblies are recommended for use with the NuPRO-935A:

![Close-up of a computer cooling fan with four cooling screws and heatsink (no visible text or labels)](.nupro-935a-50-13060-1030-204-en/03b65af61185147baefb19bd1068a24126216c9ae4413bf685e0c086c8442a87.jpg)

# 1U LGA 775 CPU Cooler

Dimensions:

• Heatsink: 92 x 87.6 x 28 mm
• Fan: 75 x 75 x 15 mm

Heatsink: Copper base + copper skived fin

Fan speed: 5500 RPM

Fan airflow: 10.48 CFM

Noise level: 51 dBA

Part number: 32-20065-0000

![Close-up of a CPU cooler with heatsink and cooling fins (no visible text or symbols)](.nupro-935a-50-13060-1030-204-en/23be3efe4528b7923a023a002ee57f35334294147aefcce0563e59e356ab61cf.jpg)

# 2U LGA 775 CPU Cooler

Dimensions:

• Heatsink: 89 x 83 x 68 mm
• Fan: 60 x 60 x 25 mm

Heatsink: Copper base + copper skived fin

Fan speed: 6800 RPM

Fan airflow: 35.3 CFM

Noise level: 46 dBA

Part number: 32-20066-0000

![Close-up of a black CPU fan with heatsink and cooling fins (no visible text or symbols)](.nupro-935a-50-13060-1030-204-en/f6c432d821784f87efc99e1b569c59142c59d1b16ab7a62b4900c48d9f10b5d6.jpg)

# 3U LGA 775 CPU Cooler

Dimensions:

• Heatsink: 100 x 100 x 70 mm
• Fan: 90 x 90 x 25 mm

Heatsink: Aluminum extrusion

Fan speed: 4500 RPM

Fan airflow: 57.7 CFM

Noise level: 47.5 dBA

Part number: 32-20058-0000 + 34-30381-0000

# CPU Fan/Heatsink Installation

When the CPU fan/heatsink installation procedures presented here are inconsistent with the installation procedures included with the CPU fan and heatsink package, follow the latter.

To install the CPU fan/heatsink:

1. Attach the backplate included with the fan/heatsink to the bottom side of the SBC. If necessary, remove the paper strip(s) from the self-adhesive pads to secure the backplate to the SBC.
2. Remove the cover or plastic protector from the CPU-side of the heatsink if necessary. The heatsink may have a thermal interface material pre-applied. If not, a packet of thermal grease will be supplied with the heatsink. Apply thermal grease evenly on top of the installed CPU if required.
3. Carefully lower the CPU fan/heatsink onto the CPU and align the captive screws with the mounting holes of the backplate. Ensure the fan cable is on the side closest to the fan connector. Begin threading each screw into the backplate, then gradually tighten the screws in a criss-cross pattern until they are fully secured (see diagram below).

![Close-up photo of a CPU fan with red directional arrows indicating rotation or cooling zones, numbered 1 to 4 pointing to the circuit board.](.nupro-935a-50-13060-1030-204-en/29159109ff396e0a40623e37e4f7d427f6ca0915a8d692a7e92ca8f70ffbc682.jpg)

![The image features a standard warning sign consisting of a yellow triangle with a black border containing a black exclamation point. Below the triangle, the text 'CAUTION:' is written in black capital letters.](.nupro-935a-50-13060-1030-204-en/aedb2d82116e6a1f8aa0982e3847c964672c4a28cc286f424ae01fe5f6ec012b.jpg)

Fully tightening a screw at one corner before beginning to tighten the other screws may cause uneven pressure to be applied to the CPU and damage the component and/or SBC.

4. Connect the CPU fan cable to the CPU fan connector on the SBC labeled FAN2 (see "Board Layout" on page 16).

Note: Do not use fan/heatsinks with push-pin type attachments. They may exert too much tension on the PCB and cause the board to flex, resulting in damage to the SBC.

# Holding the SBC with Fan/Heatsink Installed

When the fan/heatsink is installed, always hold the SBC with two hands by the card edges. Make sure to support the weight of the fan/heatsink to prevent the board from bending, resulting in damage to circuitry and/or components.

![Close-up of hands holding a green computer motherboard with visible CPU socket and cooling fan (no text or symbols)](.nupro-935a-50-13060-1030-204-en/321815abe117accab2ff1a99c38a456c2fbb85a4ca3c1e983b9067d20f3d81a1.jpg)

![The image displays a yellow triangular warning sign with a black border containing a black exclamation point. Below the triangle, the text 'CAUTION:' is written in black capital letters.](.nupro-935a-50-13060-1030-204-en/80ccfd1cd69e14e373b4e4c398a1c258509d851fa425ddc6acec52f807fad6a4.jpg)

Failure to properly support the weight of the fan/heatsink assembly when installed on the SBC may cause the board to flex and result in damage to circuitry and/or components.

# 3.3 Installing the Power Connectors

Refer to Section 2.3 Onboard Connectors on page 18 for detailed information on connectors and pin definitions referred to below.

# ATX 12V Power Connector

The NuPRO-935A requires +12V DC power connected to CN7 for proper operation in either ATX or AT modes. If necessary, order a ATX12V Convert Cable from ADLINK for use with Molex 4-pin power connectors (P/N 30-00006-0000).

# System Panel Connector

Before powering up the NuPRO-935A, connect the necessary signals from the backplane to the System Panel Connector (CN1). The ATX Power Connector pin group (pins 6-10) and Power On Button pin group (pins 19-20) must be connected for the system to power up in ATX mode.

# 3.4 Installing Memory Modules

The NuPRO-935A supports up to 4 GB of DDR2 800/667 MHz memory modules in two DDR2 DIMM sockets. A DDR2 module has a 240-pin footprint compared to the legacy 184-pin DDR DIMM. DDR2 modules are notched to facilitate correct installation on the DIMM sockets.

![The image displays a red triangular warning sign with a white border. Centered inside the triangle is a black exclamation point. Below the triangle, the text 'WARNING:' is written in black capital letters.](.nupro-935a-50-13060-1030-204-en/e036293fa53a6af54e513f95b32a5c5caadf1367a1d2ed1a5cceccb0caa174aa.jpg)

Disconnect all power supply to the board before installing a memory module to prevent damaging the board and memory module.

# Memory Configuration Options

The NuPRO-935A allows you to install 512 MB, 1GB and 2GB unbuffered non-ECC DDR2 DIMMs into the DIMM sockets following these configuration options:

▶ Channel A: DIMM1
Channel B: DIMM2
For dual-channel configuration, the total size of memory module installed per channel must be the same (DIMM1 = DIMM2).
It is recommended that you install DIMMs with the same CAS latency. For maximum compatibility, install memory modules with the same brand, model, and/or rating.

To install a memory module:

1. Locate the DIMM sockets on the SBC.
2. Press the socket's retaining clips outward to unlock.

![Mechanical component with black end caps and white connectors, no visible text or symbols](.nupro-935a-50-13060-1030-204-en/c45a3f5809d281d1454818cbcb8a86d5943078a54b2d6c3bb96db53bf99613dc.jpg)

3. Align the memory module on the socket making sure that the notch matches the break on the socket.

![Notch\n512 MB\n0087 833\nBreak](.nupro-935a-50-13060-1030-204-en/0cad67a74243008f9da406c997c1c9cda30e348d399e795fb0c00f95fb43e934.jpg)

4. Insert the module firmly into the slot until the retaining clips snap back inwards and the module is securely seated.

![Green RAM module with black connectors and red arrows indicating rotation, no visible text or symbols on the chip itself.](.nupro-935a-50-13060-1030-204-en/99e1feb7e807e3411d8bcf4ec895b9a4fc7e421d5174b108153e49b75cf9b22b.jpg)

# 4 Driver Installation

This chapter provides information on how to install the NuPRO-935A device drivers under Windows XP/Vista. The device drivers are located in the following ADLINK All-in-One DVD directories:

<table><tr><td>Chipset Driver</td><td>\NuPRO\NuPRO-935A\Chipset\</td></tr><tr><td>Display Driver</td><td>\NuPRO\NuPRO-935A\VGA\</td></tr><tr><td>LAN Driver</td><td>\NuPRO\NuPRO-935A\Ethernet\</td></tr><tr><td>ISA Driver</td><td>\NuPRO\NuPRO-935A\ISA\</td></tr><tr><td>TPM Driver</td><td>\NuPRO\NuPRO-935A\TPM\</td></tr><tr><td>Audio Driver</td><td>\Audio Daughter Board\DB-Audio2\</td></tr></table>

# 4.1 Intel® Q35 Express Chipset Driver

This section describes the installation of the Intel® Q35 Express chipset driver.

1. Locate the directory
X:\NuPRO\nuPRO-935A\Chipset\ from the ADLINK All-in-One DVD, select the operating system, then start the installation by double-clicking infinst\_autol.exe.
2. When the initial installation window appears, click Next to display the license agreement. When prompted, click Yes to continue.
3. Click Next on the Readme Information screen to begin installing the INF files.
4. When installation is complete, click Finish. Restart the system when prompted.
5. After restart, follow screen instructions to complete installation. Windows displays a found new hardware window and automatically installs the required drivers. If the New Hardware Found dialog box appears and prompts you to locate the location of the drivers, browse to the relevant directory.
6. Restart the system when prompted.

# 4.2 Display Driver

This section describes the installation of the Intel® Graphics Media Accelerator (GMA) 3000 driver.

To install the display driver:

1. Locate the display driver from this directory X:\NuPRO\nuPRO-935A\VGA\, then double-click on the Setup.exe file to start installation.
2. Follow screen instructions to complete installation, then restart the system if prompted.

# 4.3 LAN Driver

Follow these instructions to install the LAN driver.

1. Locate the LAN driver from the directory X:\NuPRO\NuPRO-935A\Ethernet\, then double-click on the PRO2KXP.exe file to start installation.
2. Follow screen instructions to complete installation, then restart the system if prompted.

# 4.4 ISA Driver

Follow these instructions to install the ISA driver.

1. Open the Device Manager on your system.

2. Right click on 'Other PCI Bridge Devices'.

3. A dialog box will appear. Select 'Update Driver...'

4. The 'Hardware Update Wizard' dialog box will open. Read the instructions and then click option 3, 'No, not this time', then click 'Next' to continue.

5. The next screen will prompt you to search for the location of the driver for your device. Click option 2, 'Install from a list or specific location (Advanced)' and then click 'Next'.

6. Locate the following folder on the ADLINK All-in-One DVD: X:\NuPRO\nuPRO-935A\ISA. Press 'Next' to install the inf files.

7. After successfully installing the files, the 'Hardware Update Wizard' will display the 'Completing the Hardware Update Wizard' screen. Click 'Finish'.

# 4.5 TPM Driver

Follow these instructions to install the TPM driver.

1. Locate the TPM driver from the directory X:\NuPRO\nuPRO-935A\TPM\ and run Setup.exe to start installation.

2. Follow the screen instructions to complete installation, then restart the system if prompted.

# 4.6 Audio Driver

Follow these instructions to install the audio driver for the optional DB-Audio2 daughter board.

![The image displays a white document icon featuring horizontal lines and a folded upper-right corner. A large, red checkmark is superimposed over the document.](.nupro-935a-50-13060-1030-204-en/a328c9369e125ee2dfc9d24ed35cbd8b48dc93f1e164687d09c402353fdcd82e.jpg)
NOTE:

Before installing the audio driver, check the BIOS settings to make sure that audio is enabled: Chipset > South Bridge Configurations > HDA Controller (see Section 5.7.1).

1. Place the ADLINK All-in-One DVD to the optical drive.
2. Locate the audio driver from the directory
X:\Audio Daughter Board\DB-Audio2\, then double-click on the setup.exe file to start installation.
3. Follow screen instructions to complete installation, then restart the system if prompted.

# 5 BIOS Setup

The following chapter describes basic navigation for the AMIBIOS®8 BIOS setup utility.

# 5.1 Starting the BIOS

To enter the setup screen, follow these steps:

1. Power on the system
2. Press the &lt; Delete &gt; key on your keyboard when you see the following text prompt:
&lt; Press DEL to run Setup &gt;
3. After you press the &lt;Delete&gt; key, the main BIOS setup menu displays. You can access the other setup screens from the main BIOS setup menu, such as Chipset and Power menus.

![American\nMegatrends\nwww.ami.com\nAMIBIOS (C) 2002 American Megatrends, Inc.\nBIOS Date: 10/08/07 12:39:39 Ver: 08.00.04\nIntel(R) Celeron(R) M Processor\nPress DEL to run Setup\nChecking NURAM..\nUSB Device(s): 2 Keyboards, 2 Mice, 1 Hub, 1 Storage Device\n1024MB OK\nAuto-Detecting Pri Master..IDE Hard Disk\nAuto-Detecting Pri Slave...ATAPI CDROM\nPri Master: 3.20 ST3B410A 007A](.nupro-935a-50-13060-1030-204-en/9fa20d8a705f2ddf8b8af03f1fbc7a5f8361e48d15dea9f56102b1a6cf268a36.jpg)

Note: In most cases, the &lt;Delete&gt; key is used to invoke the setup screen. There are several cases that use other keys, such as &lt;F1&gt;, &lt;F2&gt;, and so on.

# Setup Menu

The main BIOS setup menu is the first screen that you can navigate. Each main BIOS setup menu option is described in this user's guide.

The Main BIOS setup menu screen has two main frames. The left frame displays all the options that can be configured. "Grayed" options cannot be configured, "Blue" options can be.

The right frame displays the key legend. Above the key legend is an area reserved for a text message. When an option is selected in the left frame, it is highlighted in white. Often a text message will accompany it.

<table><tr><td colspan="7">BIOS SETUP UTILITY</td></tr><tr><td>Main</td><td>Advanced</td><td>PCIPnP</td><td>Boot</td><td>Security</td><td>Chipset</td><td>Exit</td></tr><tr><td colspan="6">System Overview</td><td rowspan="5">Use [ENTER], [TAB]or [SHIFT-TAB] toselect a field.Use [+] or [-] toconfigure system Time.</td></tr><tr><td colspan="6">AMIBIOS</td></tr><tr><td colspan="6">Version :08.00.15Build Date:07/03/08ID :N935AA10</td></tr><tr><td colspan="6">Processor</td></tr><tr><td colspan="6">Speed :255MHzCount :255</td></tr><tr><td colspan="6">System Memory</td><td rowspan="3">← Select Screen↑↓ Select Item+- Change FieldTab Select FieldF1 General HelpF10 Save and ExitESC Exit</td></tr><tr><td colspan="6">Size :503MB</td></tr><tr><td colspan="6">System Time [01:12:19]System Date [Tue 01/01/2002]</td></tr></table>

v02.61 (C) Copyright 1985-2006, American Megatrends, Inc.

# Navigation

The BIOS setup/utility uses a key-based navigation system called hot keys. Most of the BIOS setup utility hot keys can be used at any time during the setup navigation process.

These keys include &lt;F1&gt;, &lt;F10&gt;, &lt;Enter&gt;, &lt;ESC&gt;, &lt;Arrow&gt; keys, and so on.

![The flowchart describes the navigation structure of a BIOS Setup Utility.\n\n**Top Section:**\n*   A top block labeled **'BIOS Setup Utility'** points downward to the text **'Screens'**.\n*   Below 'Screens' is a horizontal sequence of boxes connected by double-headed arrows: **'Screen 1'** (-) **'Screen 2'** (-) **'Screen 3'** (-) **'Screen 4'** (-) **'Screen 5'**.\n*   A box to the left labeled **'Left and Right Keys to Select a Setup Screen'** has a dashed arrow pointing to **'Screen 1'**.\n\n**Middle Section:**\n*   An arrow points downward from 'Screens' to the text **'Items'**.\n*   Below 'Items' is a row of three boxes, each containing the symbol **'±'**, connected by double-headed arrows: **'±'** (-) **'±'** (-) **'±'**.\n*   To the left, a box labeled **'Tab Key to Select Fields'** has a dashed arrow pointing to the first **'±'** box in this row.\n*   To the right, a box labeled **'± To Change Field Values'** has a dashed arrow pointing to the third **'±'** box in this row.\n\n**Bottom Section:**\n*   Between the 'Items' row and the row below, there are downward and upward arrows.\n*   To the right, a box labeled **'Up and Down Keys to Select a Setup Item'** has a dashed arrow pointing to these vertical arrows.\n*   Below this is a second row of three boxes, each containing **'±'**, connected by double-headed arrows: **'±'** (-) **'±'** (-) **'±'**.\n*   To the left of this bottom row, the text **'Fields'** is connected via a bracket to the row of boxes.](.nupro-935a-50-13060-1030-204-en/3272d59e83491a3bf33bffcafaa0dbac6cffd70f3ba2ef780fcbd37f5d94cac3.jpg)

Note: There is a hot key legend located in the right frame on most setup screens.

The &lt; F8 &gt; key on your keyboard is the Fail-Safe key. It is not displayed on the key legend by default. To set the Fail-Safe settings of the BIOS, press the &lt; F8 &gt; key on your keyboard. It is located on the upper row of a standard 101 keyboard. The Fail-Safe settings allow the system to boot up with the least amount of options set. This can lessen the probability of conflicting settings.

# Hotkey Descriptions

F1 The &lt; F1 &gt; key allows you to display the General Help screen.

Press the &lt; F1 &gt; key to open the General Help screen.

![General Help\n↔ Select Screen ↓↑ Select Item\n+- Change Screen Enter Go to Sub Screen\nPGDN Next Page PGUP Previous Page\nHome Go to Top of the Screen End Go to Bottom of Screen\nF2/F3 Change Colors F7 Discard Changes\nF8 Load Failsafe Defaults F9 Load Optimal Defaults\nF10 Save and Exit ESC Exit\n(Ok)](.nupro-935a-50-13060-1030-204-en/f55722a8bbc02ca9c6e3aa3a3e7b8affd7d96dbfd74017c250ccc401aa117709.jpg)

F10 The &lt; F10 &gt; key allows you to save any changes you have made and exit Setup. Press the &lt; F10 &gt; key to save your changes. The following screen will appear:

![Save configuration changes and exit now?\n(Ok) (Cancel)](.nupro-935a-50-13060-1030-204-en/c4a89056435c2a54739dcf1931f9bd5779cdeb812576cab31a2b856e32d949b3.jpg)

Press the &lt;Enter&gt; key to save the configuration and exit. You can also use the &lt;Arrow&gt; key to select Cancel and then press the &lt;Enter&gt; key to abort this function and return to the previous screen.
ESC The &lt;Esc&gt; key allows you to discard any changes you have made and exit the Setup. Press the &lt;Esc&gt; key to exit the setup without saving your changes. The following screen will appear:

![Discard changes and exit setup now?\n(Ok) (Cancel)](.nupro-935a-50-13060-1030-204-en/b1643ad7520d3a4ac2fea255493761547e6b15d2bb58143bbd721b51ede66706.jpg)

Press the &lt;Enter&gt; key to discard changes and exit. You can also use the &lt;Arrow&gt; key to select Cancel and then press the &lt;Enter&gt; key to abort this function and return to the previous screen.
Enter The &lt;Enter&gt; key allows you to display or change the setup option listed for a particular setup item. The &lt;Enter&gt; key can also allow you to display the setup sub-screens.

# 5.2 Main Setup

When you first enter the Setup Utility, you will enter the Main setup screen. You can always return to the Main setup screen by selecting the Main tab. There are two Main Setup options. They are described in this section. The Main BIOS Setup screen is shown below.

<table><tr><td colspan="7">BIOS SETUP UTILITY</td></tr><tr><td>Main</td><td>Advanced</td><td>PCIPnP</td><td>Boot</td><td>Security</td><td>Chipset</td><td>Exit</td></tr><tr><td colspan="6">System Overview</td><td rowspan="5">Use [ENTER], [TAB]or [SHIFT-TAB] toselect a field.Use [+] or [-] toconfigure system Time.</td></tr><tr><td colspan="6">AMIBIOS</td></tr><tr><td colspan="6">Version :08.00.15Build Date:07/03/08ID :N935AA10</td></tr><tr><td colspan="6">Processor</td></tr><tr><td colspan="6">Speed :255MHzCount :255</td></tr><tr><td colspan="6">System MemorySize :503MB</td><td rowspan="2">← Select Screen↑↓ Select Item+- Change FieldTab Select FieldF1 General HelpF10 Save and ExitESC Exit</td></tr><tr><td colspan="6">System Time [01:12:19]System Date [Tue 01/01/2002]</td></tr></table>

v02.61 (C) Copyright 1985-2006, American Megatrends, Inc.

# System Time/System Date

Use this option to change the system time and date. Highlight System Time or System Date using the &lt;Arrow&gt; keys. Enter new values using the keyboard. Press the &lt;Tab&gt; key or the &lt;Arrow&gt; keys to move between fields. The date must be entered in MM/DD/YY format. The time is entered in HH:MM:SS format.

Note: The time is in 24-hour format. For example, 5:30 A.M. appears as 05:30:00, and 5:30 P.M. as 17:30:00.

# 5.3 Advanced BIOS Setup

Select the Advanced tab from the setup screen to enter the Advanced BIOS Setup screen. You can select any of the items in the left frame of the screen, such as SuperIO Configuration, to go to the sub menu for that item. You can display an Advanced BIOS Setup option by highlighting it using the &lt;Arrow&gt; keys. The Advanced BIOS Setup screen is shown below.

The sub menus are described on the following pages.

<table><tr><td colspan="7">BIOS SETUP UTILITY</td></tr><tr><td>Main</td><td>Advanced</td><td>PCIPnP</td><td>Boot</td><td>Security</td><td>Chipset</td><td>Exit</td></tr><tr><td colspan="7">Advanced SettingsWARNING: Setting wrong values in below sections may cause system to malfunction.CPU ConfigurationIDE ConfigurationFloppy ConfigurationSuperIO ConfigurationHardware Health ConfigurationRemote Access ConfigurationTrusted ComputingUSB ConfigurationConfigure CPU.Select Screen↑↓ Select ItemEnter Go to Sub ScreenF1 General HelpF10 Save and ExitESC Exit</td></tr><tr><td colspan="7">v02.61 (C) Copyright 1985-2006, American Megatrends, Inc.</td></tr></table>

# 5.3.1 CPU Configuration

You can use this screen to select options for the CPU Configuration Settings. Use the up and down &lt;Arrow&gt; keys to select an item. Use the &lt;+&gt; and &lt;-&gt; keys to change the value of the selected option. A description of the selected item appears on the right side of the screen. The settings are described on the following pages. An example of the CPU Configuration screen is shown below.

<table><tr><td colspan="2">BIOS SETUP UTILITY</td></tr><tr><td colspan="2">Advanced</td></tr><tr><td>Configure advanced CPU settingsModule Version:3F.08Manufacturer:IntelFrequency :255MHzFSB Speed :113MHzCache L1 :0 KBCache L2 :0 KBRatio Actual Value:9</td><td>← Select Screen↑↓ Select ItemF1 General HelpF10 Save and ExitESC Exit</td></tr><tr><td colspan="2">v02.61 (C) Copyright 1985-2006, American Megatrends, Inc.</td></tr></table>

# 5.3.2 IDE Configuration

You can use this screen to select options for the IDE Configuration Settings. Use the up and down &lt;Arrow&gt; keys to select an item. Use the &lt;+&gt; and &lt;-&gt; keys to change the value of the selected option. A description of the selected item appears on the right side of the screen. The settings are described on the following pages. An example of the IDE Configuration screen is shown below.

<table><tr><td colspan="3">BIOS SETUP UTILITY</td></tr><tr><td colspan="3">Advanced</td></tr><tr><td colspan="2">IDE Configuration</td><td>Options</td></tr><tr><td>SATA#1 Configuration</td><td>[Compatible]</td><td>Disabled</td></tr><tr><td>SATA#2 Configuration</td><td>[Enhanced]</td><td>Compatible</td></tr><tr><td>Primary IDE Master</td><td>: [Not Detected]</td><td>Enhanced</td></tr><tr><td>Primary IDE Slave</td><td>: [Not Detected]</td><td></td></tr><tr><td>Secondary IDE Master</td><td>: [Not Detected]</td><td></td></tr><tr><td>Secondary IDE Slave</td><td>: [Not Detected]</td><td></td></tr><tr><td>Third IDE Master</td><td>: [Not Detected]</td><td></td></tr><tr><td>Fourth IDE Master</td><td>: [Not Detected]</td><td></td></tr><tr><td></td><td></td><td>← Select Screen↑↓ Select Item+- Change OptionF1 General HelpF10 Save and ExitESC Exit</td></tr></table>

# SATA Configuration

This item specifies which mode the SATA channels should be initialized in. The settings are Disabled, Compatible and Enhanced. When running in Compatible mode, SATA channel can be configured as a legacy IDE channel.

# IDE Master/Slave

Select one of the hard disk drives to configure it. Press &lt;Enter&gt; to access its sub menu.

# 5.3.3 Floppy Configuration

You can use this screen to specify options for the Floppy Configuration Settings. Use the up and down &lt;Arrow&gt; keys to select an item. Use the &lt;+&gt; and &lt;-&gt; keys to change the value of the selected option. The settings are described on the following pages. The screen is shown below.

<table><tr><td colspan="2">BIOS SETUP UTILITY</td></tr><tr><td colspan="2">Advanced</td></tr><tr><td>Floppy Configuration</td><td rowspan="2">Select the type offloppy driveconnected to thesystem.</td></tr><tr><td>Floppy A [1.44 MB 3 $\frac{1}{2}$ &quot;]</td></tr><tr><td></td><td>← Select Screen↑↓ Select Item+- Change OptionF1 General HelpF10 Save and ExitESC Exit</td></tr></table>

Options: 360 KB 5 $\frac{1}{4}$ ", 1.2 MB 5 $\frac{1}{4}$ ", 720 KB 3 $\frac{1}{2}$ ", 1.44 MB 3 $\frac{1}{2}$ ", 2.88 MB 3 $\frac{1}{2}$ ".

# 5.3.4 Super IO Configuration

You can use this screen to select options for the Super IO settings. Use the up and down &lt;Arrow&gt; keys to select an item. Use the &lt;+&gt; and &lt;-&gt; keys to change the value of the selected option. The settings are described on the following pages. The screen is shown below.

<table><tr><td colspan="2">BIOS SETUP UTILITY</td></tr><tr><td colspan="2">Advanced</td></tr><tr><td colspan="2">Configure ITE8718 Super IO Chipset</td></tr><tr><td>OnBoard Floppy Controller [Enabled]Serial Port1 Address [3F8/IRQ4]Serial Port2 Address [2F8/IRQ3]Parallel Port Address [378]Parallel Port Mode [Normal]Parallel Port IRQ [IRQ7]</td><td>Allows BIOS to Enable or Disable Floppy Controller.← Select Screen↑↓ Select Item+- Change OptionF1 General HelpF10 Save and ExitESC Exit</td></tr></table>

# Onboard Floppy Controller

Options: Disabled, Enabled

# Serial Port1 Address

Select an address and a corresponding interrupt for Serial Port1. Options: 3F8/IRQ4, 3E8/IRQ4, 2F8/IRQ3, 2E8/IRQ3.

# Serial Port2 Address

This option specifies the base I/O port address and Interrupt Request address of Serial Port2. The settings of Serial Port2 are the same as Serial Port1. However, the setting used by Serial Port1 will not be available for Serial Port2. For example, if Serial Port1 uses 3F8/IRQ4, the option, the 3F8/IRQ4 will not appear in the options of Serial Port2.

# Parallel Port Mode

This option specifies the parallel port mode.

▶ Normal: Set this value to allow the standard parallel port mode to be used.
▶ EPP: The parallel port can be used with devices that adhere to the Enhanced Parallel Port (EPP) specification. EPP uses the existing parallel port signals to provide asymmetric bi-directional data transfer driven by the host device.
▶ ECP: The parallel port can be used with devices that adhere to the Extended Capabilities Port (ECP) specification. ECP uses the DMA protocol to achieve data transfer rates up to 2.5 Megabits per second. ECP provides symmetric Bi-directional communication.
▶ EPP+ECP: Allow the parallel port to support both the ECP and EPP modes simultaneously.

# Parallel Port IRQ

This option specifies the IRQ used by the parallel port.

- IRQ5: Set this value to allow the serial port to use Interrupt 5.
▶ IRQ7: Set this value to allow the serial port to use Interrupt 7. The majority of parallel ports on computer systems use IRQ7 and I/O Port 378H as the standard setting.

# 5.3.5 Hardware Health Configuration

This option displays the current status of all of the monitored hardware devices / components such as voltages and temperatures.

<table><tr><td colspan="2">BIOS SETUP UTILITY</td></tr><tr><td colspan="2">Advanced</td></tr><tr><td colspan="2">Hardware Health ConfigurationCPU Temperature :39°C/102°FSystem Temperature :38°C/100°FFan1 Speed :4192 RPMFan2 Speed :N/ACPU Core :1.200 U+3.30U :3.376 U+5.00U :4.784 U+12.0U :12.032 U5USB :4.677 U← Select Screen↑↓ Select ItemF1 General HelpF10 Save and ExitESC Exit</td></tr></table>

v02.61 (C) Copyright 1985-2006, American Megatrends, Inc.

# 5.3.6 Remote Access Configuration

Remote access configuration provides the settings to allow remote access by another computer to get POST messages and send commands through serial port access.

<table><tr><td colspan="2">BIOS SETUP UTILITY</td></tr><tr><td colspan="2">Advanced</td></tr><tr><td colspan="2">Configure Remote Access type and parameters</td></tr><tr><td>Remote Access</td><td>[Enabled]</td></tr><tr><td>Serial port number</td><td>[COM1]</td></tr><tr><td>Base Address, IRQ</td><td>[3F8h, 4]</td></tr><tr><td>Serial Port Mode</td><td>[115200 8,n,1]</td></tr><tr><td>Flow Control</td><td>[None]</td></tr><tr><td>Redirection After BIOS POST</td><td>[Always]</td></tr><tr><td>Terminal Type</td><td>[ANSI]</td></tr><tr><td>UT-UTF8 Combo Key Support</td><td>[Enabled]</td></tr><tr><td>Sredir Memory Display Delay</td><td>[No Delay]</td></tr><tr><td></td><td></td></tr></table>

v02.61 (C) Copyright 1985-2006, American Megatrends, Inc.

# Remote Access

Select this option to Enable or Disable the BIOS remote access feature.

Note: Enabling Remote Access requires a dedicated serial port connection. Once both serial ports are configured to disabled, you should set this value to Disabled or it may cause abnormal boot.

# Serial Port Number

Select the serial port you want to use for the remote access interface. You can set the value for this option to COM1 or COM2.

Note: If you have changed the resource assignment of the serial ports in Advanced> SuperIO Configuration, you must Save Changes and Exit, reboot the system, and enter the setup menu again in order to see those changes reflected in the available Remote Access options.

# Serial Port Mode

Select the baud rate you want the serial port to use for console redirection. The options are 115200 8,n,1; 57600 8,n,1; 19200 8,n,1; and 09600 8,n,1.

# Flow Control

Set this option to select Flow Control for console redirection. The settings for this value are None, Hardware, or Software.

# Redirection After BIOS POST

This option allows you to set Redirection configuration after BIOS POST. The settings for this value are Disabled, Boot Loader, or Always.

▶ Disabled: Set this value to turn off the redirection after POST
▶ Boot Loader: Set this value to allow the redirection to be active during POST and Boot Loader.
▶ Always: Set this value to allow the redirection to be always active.

# Terminal Type

This option is used to select either VT100/VT-UTF8 or ANSI terminal type. The settings for this value are ANSI, VT100, or VT-UTF8.

# VT-UTF8 Combo Key Support

This option enables VT-UTF8 Combination Key Support for ANSI/VT100 terminals. The settings for this value are Enabled or Disabled.

# Sredir Memory Display Delay

This option gives the delay in seconds to display memory information. The options for this value are No Delay, Delay 1 Sec, Delay 2 Sec, or Delay 4 Sec.

# 5.3.7 Trusted Computing

Trusted computing is an industry standard to make personal computers more secure through a dedicated hardware chip, called a Trusted Platform Module (TPM). This option enables or disables the TPM support.

<table><tr><td colspan="2">BIOS SETUP UTILITY</td></tr><tr><td colspan="2">Advanced</td></tr><tr><td>Trusted ComputingTCG/TPM SUPPORT [Yes]Execute TPM Command [Don&#x27;t changel]Clearing the TPM [Press Enter]TPM Enable/Disable Status [Disabled]TPM Owner Status [UnOwned]</td><td>Enable/Disable TPMTCG (TPM 1.1/1.2) supp in BIOS← Select Screen↑↓ Select Item+- Change OptionF1 General HelpF10 Save and ExitESC Exit</td></tr></table>

v02.61 (C) Copyright 1985-2006, American Megatrends, Inc.

# 5.3.8 USB Configuration

You can use this screen to select options for the USB Configuration. Use the up and down &lt;Arrow&gt; keys to select an item. Use the &lt;+&gt; and &lt;-&gt; keys to change the value of the selected option. The settings are described on the following pages. The screen is shown below.

<table><tr><td colspan="2">BIOS SETUP UTILITY</td></tr><tr><td colspan="2">Advanced</td></tr><tr><td>USB ConfigurationModule Version - 2.24.0-11.4USB Devices Enabled :1 DriveLegacy USB Support [Enabled]Port 64/60 Emulation [Disabled]USB 2.0 Controller Mode [HiSpeed]BIOS EHCI Hand-Off [Enabled]USB Mass Storage Device Configuration</td><td>Enables support for legacy USB. AUTO option disables legacy support if no USB devices are connected.&lt; Select Screen↑↓ Select Item+- Change OptionF1 General HelpF10 Save and ExitESC Exit</td></tr></table>

v02.61 (C) Copyright 1985-2006, American Megatrends, Inc.

# Legacy USB Support

Legacy USB Support refers to USB mouse and keyboard support. Normally if this option is not enabled, any attached USB mouse or USB keyboard will not become available until a USB compatible operating system is fully booted with all USB drivers loaded. When this option is enabled, any attached USB mouse or USB keyboard can control the system even when there are no USB drivers loaded on the system. Set this value to enable or disable the Legacy USB Support.

▶ Disabled: Set this value to prevent the use of any USB device in DOS or during system boot.
▶ Enabled: Set this value to allow the use of USB devices during boot and while using DOS.
▶ Auto: This option auto detects USB Keyboards or Mice and if found, allows them to be utilized during boot and while using DOS.

# Port 64/60 Emulation

This option uses USB to receive the IO port 64/60 trap to emulate the legacy keyboard controller.

# USB 2.0 Controller Mode

The USB 2.0 Controller Mode configures the data rate of the USB port. The options are FullSpeed (12 Mbps) and HiSpeed (480 Mbps).

# BIOS EHCI hand-off

This option provides a workaround for operating systems without ECHI hand-off support. The EHCI ownership change should claim by EHCI driver.

# USB Mass Storage Device Configuration

This is a submenu for configuring the USB Mass Storage Class Devices when BIOS finds they are in use on USB ports. Emulation Type can be set according to the type of attached USB mass storage device(s). If set to Auto, USB devices less than 530MB will be emulated as Floppy and those greater than 530MB will remain as hard drive. The Forced FDD option can be used to force a hard disk type drive (such as a Zip drive) to boot as FDD.

<table><tr><td colspan="2">BIOS SETUP UTILITY</td></tr><tr><td colspan="2">Advanced</td></tr><tr><td>USB Mass Storage Device ConfigurationUSB Mass Storage Reset Delay [20 Sec]Device #1 USB Flash DiskEmulation Type [Auto]</td><td>Number of secondsPOST waits for theUSB mass storagedevice after startunit command.← Select Screen↑↓ Select Item+- Change OptionF1 General HelpF10 Save and ExitESC Exit</td></tr></table>

v02.61 (C) Copyright 1985-2006, American Megatrends, Inc.

# 5.4 Advanced PCI/PnP Settings

Select the PCI/PnP tab from the setup screen to enter the Plug and Play BIOS Setup screen. You can display a Plug and Play BIOS Setup option by highlighting it using the &lt;Arrow&gt; keys. The Plug and Play BIOS Setup screen is shown below.

![BIOS SETUP UTILITY\nMain Advanced PCIPnP Boot Security Chipset Exit\nAdvanced PCI/PnP Settings\nWARNING: Setting wrong values in below sections\nmay cause system to malfunction.\nIRQ3 (Reserved)\nIRQ4 (Reserved)\nIRQ5 (Available)\nIRQ7 (Reserved)\nIRQ9 (Available)\nIRQ10 (Available)\nIRQ11 (Available)\nIRQ14 (Available)\nIRQ15 (Available)\nDMA Channel 0 (Available)\nDMA Channel 1 (Available)\nDMA Channel 3 (Available)\nDMA Channel 5 (Available)\nAvailable: Specified\nIRQ is available to be\nused by PCI/PnP\ndevices.\nReserved: Specified\nIRQ is reserved for\nuse by Legacy ISA\ndevices.\n← Select Screen\n↑↓ Select Item\n+- Change Option\nF1 General Help\nF10 Save and Exit\nESC Exit](.nupro-935a-50-13060-1030-204-en/b927dce6fa18665aa10a4100eab28f5bc24824553671f722210cc1cf679fe138.jpg)

v02.61 (C) Copyright 1985-2006, American Megatrends, Inc.

# 5.4.1 IRQ/DMA

Set this value to allow the IRQ settings to be modified. Available – This setting allows the specified IRQ/DMA to be used by a PCI/PnP device. Reserved – This setting allows the specified IRQ/DMA to be used by a legacy ISA device.

# 5.4.2 ISA Plug and Play

This setting enables/disables the ISA Plug and Play functionality.

<table><tr><td colspan="6">BIOS SETUP UTILITY</td></tr><tr><td>Main</td><td>Advanced</td><td>PCIPnP</td><td>Boot</td><td>Security</td><td>Chipset Exit</td></tr><tr><td></td><td></td><td></td><td></td><td></td><td rowspan="3">Enabled: LPT 278h will have conflict with ISA PnP configuration port</td></tr><tr><td>IRQ3</td><td></td><td></td><td>[Reserved]</td><td></td></tr><tr><td>IRQ4</td><td></td><td></td><td>[Reserved]</td><td></td></tr><tr><td>IRQ5</td><td></td><td></td><td>[Available]</td><td></td><td rowspan="7">ISA window 380h-29Fh will be disabled for ISA PnP port.</td></tr><tr><td>IRQ7</td><td></td><td></td><td>[Reserved]</td><td></td></tr><tr><td>IRQ9</td><td></td><td></td><td>[Available]</td><td></td></tr><tr><td>IRQ10</td><td></td><td></td><td>[Available]</td><td></td></tr><tr><td>IRQ11</td><td></td><td></td><td>[Available]</td><td></td></tr><tr><td>IRQ14</td><td></td><td></td><td>[Available]</td><td></td></tr><tr><td>IRQ15</td><td></td><td></td><td>[Available]</td><td></td></tr><tr><td>DMA Channel 0</td><td></td><td></td><td>[Available]</td><td></td><td>← Select Screen</td></tr><tr><td>DMA Channel 1</td><td></td><td></td><td>[Available]</td><td></td><td>↑↓ Select Item</td></tr><tr><td>DMA Channel 3</td><td></td><td></td><td>[Available]</td><td></td><td>+- Change Option</td></tr><tr><td>DMA Channel 5</td><td></td><td></td><td>[Available]</td><td></td><td>F1 General Help</td></tr><tr><td>DMA Channel 6</td><td></td><td></td><td>[Available]</td><td></td><td>F10 Save and Exit</td></tr><tr><td>DMA Channel 7</td><td></td><td></td><td>[Available]</td><td></td><td>ESC Exit</td></tr><tr><td colspan="3">Enable ISA PnP configuration</td><td>[Enabled]</td><td></td><td></td></tr></table>

# 5.5 Boot Settings

Select the Boot tab from the setup screen to enter the Boot BIOS Setup screen. You can select any of the items in the left frame of the screen, such as Boot Device Priority, to go to the sub menu for that item. You can display a Boot BIOS Setup option by highlighting it using the &lt;Arrow&gt; keys. The Boot Settings screen is shown below:

<table><tr><td colspan="2">Main Advanced PCIPnP Boot Security Chipset Exit</td></tr><tr><td>Boot Settings</td><td rowspan="8">Configure Settings during System Boot.</td></tr><tr><td>▶ Boot Settings Configuration</td></tr><tr><td>▶ Boot Device Priority</td></tr><tr><td>▶ Hard Disk Drives</td></tr><tr><td>▶ Removable Drives</td></tr><tr><td>▶ CD/DVD Drives</td></tr><tr><td>▶ USB Drives</td></tr><tr><td>▶ Network Drives</td></tr><tr><td></td><td>← Select Screen↑↓ Select ItemEnter Go to Sub ScreenF1 General HelpF10 Save and ExitESC Exit</td></tr></table>

# 5.5.1 Boot Settings Configuration

Use this screen to select options for the Boot Settings Configuration. Use the up and down &lt;Arrow&gt; keys to select an item. Use the &lt;Plus&gt; and &lt;Minus&gt; keys to change the value of the selected option. The settings are described on the following pages. The screen is shown below.

# BIOS SETUP UTILITY

# Boot

Boot Settings Configuration

<table><tr><td>Quick Boot</td></tr><tr><td>Quiet Boot</td></tr><tr><td>Bootup Num-Lock</td></tr></table>

<table><tr><td>[Enabled]</td></tr><tr><td>[Disabled]</td></tr><tr><td>[On]</td></tr></table>

<table><tr><td>Allows BIOS to skip certain tests while booting. This will decrease the time needed to boot the system.</td></tr></table>

<table><tr><td>←</td><td>Select Screen</td></tr><tr><td>↑↓</td><td>Select Item</td></tr><tr><td>+-</td><td>Change Option</td></tr><tr><td>F1</td><td>General Help</td></tr><tr><td>F10</td><td>Save and Exit</td></tr><tr><td>ESC</td><td>Exit</td></tr></table>

v02.61 (C) Copyright 1985-2006, American Megatrends, Inc.

# Quick Boot

Enabling this setting will cause the BIOS power-on self test routine to skip some of its tests during bootup for faster system boot.

# Quiet Boot

When this feature is enabled, the BIOS will display the full-screen logo during the boot-up sequence, hiding normal POST messages.

When it is disabled, the BIOS will display the normal POST messages, instead of the full-screen logo.

# Bootup Num-Lock

This setting is to set the Num Lock status when the system is powered on. Setting to [On] will turn on the Num Lock key when the system is powered on. Setting to [Off] will allow users to use the arrow keys on the numeric keypad.

# 5.5.2 Boot Device Priority

The items allow you to set the sequence of boot devices where BIOS attempts to load the disk operating system. First press &lt;Enter&gt; to enter the sub-menu. Then you may use the arrow keys to select the desired device, then press &lt;+&gt;, &lt;-&gt; or &lt;PageUp&gt;, &lt;PageDown&gt; key to move it up/down in the priority list.

# 5.5.3 Boot Device Groups

The Boot devices are listed in groups by device type. First press &lt;Enter&gt; to enter the sub-menu. Then you may use the arrow keys to select the desired device, then press &lt;+&gt;, &lt;-&gt; or &lt;PageUp&gt;, &lt;PageDown&gt; key to move it up/down in the priority list. Only the first device in each device group will be available for selection in the Boot Device Priority option.

# 5.6 Security Setup

<table><tr><td colspan="6">BIOS SETUP UTILITY</td></tr><tr><td colspan="6">Main Advanced PCIPnP Boot Security Chipset Exit</td></tr><tr><td colspan="4">Security Settings</td><td rowspan="2" colspan="2">Install or Change the password.</td></tr><tr><td rowspan="2" colspan="4">Supervisor Password :Not InstalledUser Password :Not InstalledChange Supervisor PasswordChange User PasswordClear User Password</td></tr><tr><td colspan="2">← Select Screen↑↓ Select ItemEnter ChangeF1 General HelpF10 Save and ExitESC Exit</td></tr><tr><td colspan="6">v02.61 (C) Copyright 1985-2006, American Megatrends, Inc.</td></tr></table>

# Password Support

# Two Levels of Password Protection

Provides both a Supervisor and a User password. If you use both passwords, the Supervisor password must be set first.

The system can be configured so that all users must enter a password every time the system boots or when Setup is executed, using either or either the Supervisor password or User password.

The Supervisor and User passwords activate two different levels of password security. If you select password support, you are prompted for a one to six character password. Type the password on the keyboard. The password does not appear on the screen when typed. Make sure you write it down. If you forget it, you must drain NVRAM and re-configure.

# Remember the Password

Keep a record of the new password when the password is changed. If you forget the password, you must erase the system configuration information in NVRAM.

To access the sub menu for the following items, select the item and press &lt; Enter&gt;:

▶ Change Supervisor Password
▶ Change User Password
▶ Clear User Password

# Supervisor Password

Indicates whether a supervisor password has been set.

# User Password

Indicates whether a user password has been set.

# Change Supervisor Password

Select this option and press &lt; Enter &gt; to access the sub menu. You can use the sub menu to change the supervisor password.

# Change User Password

Select this option and press &lt; Enter &gt; to access the sub menu. You can use the sub menu to change the user password.

# Clear User Password

Select this option and press &lt; Enter &gt; to access the sub menu. You can use the sub menu to clear the user password.

# Change Supervisor Password

Select Change Supervisor Password from the Security Setup menu and press &lt; Enter &gt;.

Enter New Password:

Type the password and press &lt; Enter &gt;. The screen does not display the characters entered. Retype the password as prompted and press &lt; Enter &gt;. If the password confirmation is incorrect, an error message appears. The password is stored in NVRAM after completes.

# Change User Password

Select Change User Password from the Security Setup menu and press &lt; Enter &gt;.

Enter New Password:

Type the password and press &lt; Enter &gt;. The screen does not display the characters entered. Retype the password as prompted and press &lt; Enter &gt;. If the password confirmation is incorrect, an error message appears. The password is stored in NVRAM after completes.

# 5.7 Chipset Setup

Select the Chipset tab from the setup screen to enter the Chipset BIOS Setup screen. You can select any of the items in the left frame of the screen to go to the sub menu for that item. The Chipset BIOS Setup screen is shown below.

<table><tr><td colspan="6">BIOS SETUP UTILITY</td></tr><tr><td>Main</td><td>Advanced</td><td>PCIPnP</td><td>Boot</td><td>Security</td><td>Chipset Exit</td></tr><tr><td colspan="5">Advanced Chipset SettingsWARNING: Setting wrong values in below sections may cause system to malfunction.► South Bridge ConfigurationACPI Aware O/S [Yes]Resume On PMEN [Disabled]Restore on AC Power Loss [Last State]Power Button Mode [On/Off]← Select Screen↑↓ Select ItemEnter Go to Sub ScreenF1 General HelpF10 Save and ExitESC Exitv02.61 (C) Copyright 1985-2006, American Megatrends, Inc.</td><td>Configure South Bridge features.← Select Screen↑↓ Select ItemEnter Go to Sub ScreenF1 General HelpF10 Save and ExitESC Exit</td></tr></table>

# 5.7.1 South Bridge Configuration

You can use this screen to select options for the South Bridge Configuration. Use the up and down &lt;Arrow&gt; keys to select an item. Use the &lt;Plus&gt; and &lt;Minus&gt; keys to change the value of the selected option.

<table><tr><td colspan="2">BIOS SETUP UTILITY</td></tr><tr><td colspan="2">Chipset</td></tr><tr><td>South Bridge Chipset Configuration</td><td>Options</td></tr><tr><td rowspan="2">GbE LAN Boot [Disabled]GbE Wake Up From S5 [Disabled]HDA Controller [Enabled]</td><td>EnabledDisabled</td></tr><tr><td>← Select Screen↑↓ Select Item+- Change OptionF1 General HelpF10 Save and ExitESC Exit</td></tr></table>

# GbE LAN Boot

Invoke the onboard LAN's PXE ROM to enable boot from LAN. The options are Enabled and Disabled.

# GbE Wake Up From S5

Set onboard LAN boot wake up from power down mode. The options are Enabled and Disabled.

# HDA Controller

Set this value to Enable/Disable the HDA Controller.

# 5.7.2 Advanced Chipset Settings

# ACPI Aware O/S

This option specifies which OS support ACPI. The options are Enabled and Disabled.

# Resume On PME#

This option specifies if the PME#. event will generate a system wake event. The sub-options are Enabled and Disabled.

# Restore on AC Power Loss

Determines which state the computer enters when AC power is restored after a power loss. The options for this value are Last State, Power On and Power Off.

▶ Power Off: Set this value to always power off the system while AC power is restored.
▶ Power On: Set this value to always power on the system while AC power is restored.
▶ Last State: Set this value to power off/on the system depending on the last system power state while AC power is restored.

# Power Button Mode

This option specifies the effect when the power button pressed.

▶ On/Off: The system is powered down immediately if the power button is pressed.
▶ Suspend: The system is powered down if the power button is pressed for more than four seconds. Pressing the button momentarily (for less than 4 seconds) will put the system in "suspend" mode.

# 5.8 Exit Menu

Select the Exit tab from the setup screen to enter the Exit BIOS Setup screen. You can display an Exit BIOS Setup option by highlighting it using the &lt;Arrow&gt; keys. The Exit BIOS Setup screen is shown below.

<table><tr><td colspan="7">BIOS SETUP UTILITY</td></tr><tr><td>Main</td><td>Advanced</td><td>PCIPnP</td><td>Boot</td><td>Security</td><td>Chipset</td><td>Exit</td></tr><tr><td colspan="6">Exit Options</td><td rowspan="2">Exit system setup after saving the changes.F10 key can be used for this operation.← Select Screen↑↓ Select ItemEnter Go to Sub ScreenF1 General HelpF10 Save and ExitESC Exit</td></tr><tr><td colspan="6">Save Changes and ExitDiscard Changes and ExitDiscard ChangesLoad Optimal DefaultsLoad Failsafe Defaults</td></tr></table>

v02.61 (C) Copyright 1985-2006, American Megatrends, Inc.

# Save Changes and Exit

When you have completed the system configuration changes, select this option to leave Setup and reboot the computer so the new system configuration parameters can take effect.

Save Configuration Changes and Exit Now?

[Ok] [Cancel]

appears in the window. Select Ok to save changes and exit.

# Discard Changes and Exit

Select this option to quit Setup without making any permanent changes to the system configuration.

Discard Changes and Exit Setup Now?

[Ok] [Cancel]

appears in the window. Select Ok to discard changes and exit.

# Discard Changes

Select Discard Changes from the Exit menu and press &lt; Enter &gt;.

Select Ok to discard changes.

# Load Optimal Defaults

Automatically sets all Setup options to a complete set of default settings when you select this option. The Optimal settings are designed for maximum system performance, but may not work best for all computer applications. In particular, do not use the Optimal Setup options if your computer is experiencing system configuration problems.

Select Load Optimal Defaults from the Exit menu and press &lt;Enter&gt;.

Select Ok to load optimal defaults.

# Load Failsafe Defaults

Automatically sets all Setup options to a complete set of default settings when you select this option. The Failsafe settings are designed for maximum system stability, but not maximum performance. Select the FailSafe Setup options if your computer is experiencing system configuration problems.

Select Load Fail-Safe Defaults from the Exit menu and press &lt;Enter&gt;.

Load FailSafe Defaults?

[Ok] [Cancel]

appears in the window. Select Ok to load FailSafe defaults.

This page intentionally left blank.

# Appendix A - Watchdog Timer

A sample program for configuring the NuPRO-935A's watchdog timer is included on the ADLINK All-in-One DVD in the following directory: \NuPRO\NuPRO-935A\WDT.

# A.1 Sample Code

```c
#include&lt;stdlib.h&gt;
#include&lt;stdio.h&gt;
#include&lt;string.h&gt;
#include&lt;dos.h&gt;

void WDTRUN(int config_port, int count_value);
void Enter_IT8718_Config(int config_port);
void Exit_IT8718_Config(int config_port);

void main(int argc, char *argv[])
{
    int number, DevID1, DevID2, chipflag = 0;
    int iport = 0x2E; // Default config_port = 0x2E

    if ((argc == 1) || ((argc == 3) && (*argv[2] != '4') && (*argv[3] != 'E')) || (argc > 3))
    {
    printf("ADLINK Watchdog Timer Utility of NuPRO-935A\n\n");
    printf(" Usage: ITE8718 value [4E]\n");
    printf(" value: 1 to 15300 second.\n");
    printf(" Write 0 will disable watchdog timer.\n\n");
    printf(" 4E - change IO port to 0x4E. Default is 0x2E.\n");
    exit(1);
    }
    else
    {
    // User selected io port.
    if (argc == 3) { iport = 0x4E;
    printf("IOPORT Usage: 0x4E\n");
    }
}
```

```c
//Detect ITE8718F.
Enter_IT8718_Config(ioport);

//Get Chip ID Byte 1 = 0x87, Gip ID Byte 2 = 0x18
outportb(ioport, 0x20);
DevID1 = importb(ioport+1);
outportb(ioport, 0x21);
DevID2 = importb(ioport+1);

if((DevID1 == 0x87) && (DevID2 == 0x18))
    chipflag = 1;

if(chipflag == 0)
{
    printf("ADLINK Watchdog Timer Utility of NuPRO-935A\n\n");
    printf("Can't find any ITE IT8718F on system!\n");
    Exit_IT8718_Config(ioport);
    exit(1);
}
else
{
    printf("ADLINK Watchdog Timer Utility of NuPRO-935A\n\n");
    number=atoi(argv[1]);

    WDTRUN(ioport,number);
    Exit_IT8718_Config(ioport);
}
}

void Enter_IT8718_Config(int config_port)
{
    switch(config_port)
    {
    case 0x2E:
    //Address port = 0x2E, enter keys = 0x87, 0x01, 0x55, 0x55
```

```c
outportb(0x2E, 0x87);
outportb(0x2E, 0x01);
outportb(0x2E, 0x55);
outportb(0x2E, 0x55);
break;
case 0x4E:
    //Address port = 0x4E, enter keys
= 0x87, 0x01, 0x55, 0xAA
    outportb(0x2E, 0x87);
    outportb(0x2E, 0x01);
    outportb(0x2E, 0x55);
    outportb(0x2E, 0xAA);
    break;
default:
    break;
}
void Exit_IT8718_Config(int config_port)
{
    outportb(config_port, 0x02);
    outportb(config_port+1, 0x02);
}
void WDTRUN(int config_port, int count_value)
{
    int temp;
    int counter;

    //Select WDT device
    outportb(config_port, 0x07);
    outportb(config_port+1, 0x07); //device 7

    //Set second/minute mode
    outportb(config_port, 0x72);
    temp = inportb(config_port+1);

    if(count_value == 0)
    {
    counter = count_value;
    printf("WDT is Disabled.");
    outportb(config_port+1, temp); //WDT
    output through PWROK2 default is Disabled.
    } // end of (count_value == 0)
```

```c
else if(count_value &lt;= 60){
    temp = temp | 0x80;//chip's default is minute.
    counter = count_value;
    printf("WDT timeout in %d seconds.",counter);
    // temp = temp | 0x40;//enable WDT output through KBRST
    temp = temp | 0x10;//enable WDT output through PWROK2 (pulse)
    outportb(config_port+1, temp);
    } // end of (count_value&lt;=60) else if(((count_value&gt;60) && (count_value&lt;=15300)) || (count_value &gt; 15300))
    {
    //Count the timeout value
    if(count_value > 15300)
    count_value = 15300;
    counter = count_value/60;
    if((count_value%60)>30)
    counter=counter+1;
    printf("WDT timeout in %d minutes.",counter);
    // temp = temp | 0x40;//enable WDT output through KBRST
    temp = temp | 0x10;//enable WDT output through PWROK2 (pulse)
    outportb(config_port+1, temp);
    } // end of (count_value>60)

    //reset WDT by KB, MS interrupt
    // outportb(config_port, 0x71);
    // temp = inportb(config_port + 1);
    // temp = temp | 0x60;//Bit 6 = KB interrupt, Bit 5 = MS interrupt
    // outportb(config_port+1, temp);
    //Write count value
    outportb(config_port, 0x73);
    outportb(config_port+1, counter);

} // end of WDTRUN
```

# Appendix B System Resources

B.1 System Memory Map

<table><tr><td>Address Range (decimal)</td><td>Address Range (hex)</td><td>Size</td><td>Description</td></tr><tr><td>(4GB-2MB)</td><td>FFE00000 - FFFFFFFF</td><td>2 MB</td><td>High BIOS Area</td></tr><tr><td>(4GB-18MB) - (4GB-17MB-1)</td><td>FEE00000 - FEEFFFFFF</td><td>1 MB</td><td>FSB Interrupt Memory Space</td></tr><tr><td>(4GB-20MB) - (4GB-19MB-1)</td><td>FEC00000 - FECFFFFFF</td><td>1 MB</td><td>APIC Configuration Space</td></tr><tr><td>15MB - 16MB</td><td>F00000 - FFFFFFF</td><td>1 MB</td><td>ISA Hole</td></tr><tr><td>960 K - 1024 K</td><td>F0000 - FFFFF</td><td>64 KB</td><td>System BIOS Area</td></tr><tr><td>896 K - 960 K</td><td>E0000 - EFFFF</td><td>64 KB</td><td>Extended System BIOS Area</td></tr><tr><td>768 K - 896 K</td><td>C0000 - DFFFF</td><td>128 KB</td><td>PCI expansion ROM areaC0000 - C7FFF: Onboard VGA BIOSCB800 - CC7FFF: Intel 82566DM PXE option ROM when onboard LAN boot ROM is enabled.CC800 - CD7FFF: Marvell 88E805 option ROM when onboard LAN boot ROM is enabled.</td></tr><tr><td>640 K - 768 K</td><td>A0000 - BFFFF</td><td>128 KB</td><td>Video Buffer &amp; SMM space</td></tr><tr><td>0 K - 640 K</td><td>00000 - 9FFFF</td><td>640 KB</td><td>DOS Area</td></tr></table>

Table B-1: System Memory Map

B.2 Direct Memory Access Channels

<table><tr><td>Channel Number</td><td>Data Width</td><td>System Resource</td></tr><tr><td>0</td><td>8-bits</td><td>Parallel port(1)</td></tr><tr><td>1</td><td>8-bits</td><td>Parallel port(1)</td></tr><tr><td>2</td><td>8-bits</td><td>Diskette drive(1)</td></tr><tr><td>3</td><td>8-bits</td><td>Parallel port(1)</td></tr><tr><td>4</td><td></td><td>Reserved - cascade channel</td></tr><tr><td>5</td><td>16-bits</td><td>Open</td></tr><tr><td>6</td><td>16-bits</td><td>Open</td></tr><tr><td>7</td><td>16-bits</td><td>Open</td></tr></table>

Table B-2: Direct Memory Access Channels
Note (1): DMA channel 0/1/3 is selected when using parallel port. Floppy and parallel port cannot be used at the same time.

B.3 IO Map

<table><tr><td>Hex Range</td><td>Device</td></tr><tr><td>000-01F</td><td>DMA controller 1, 8237A-5 equivalent</td></tr><tr><td>020-02D and 030-03F</td><td>Interrupt controller 1, 8259 equivalent</td></tr><tr><td>02E-02F</td><td>LPC SIO (ITE8718) configuration index/data registers</td></tr><tr><td>040-05F</td><td>Timer, 8254-2 equivalent</td></tr><tr><td>060, 062, 064, 066, 068-06F</td><td>8742 equivalent (keyboard)</td></tr><tr><td>061, 063, 065, 067</td><td>NMI control and status</td></tr><tr><td>070-07F</td><td>Real Time Clock Controller( bit 7 -NMI mask)</td></tr><tr><td>080-091</td><td>DMA page register</td></tr><tr><td>092</td><td>Reset (Bit 0)/ Fast Gate A20 (Bit 1)</td></tr><tr><td>93-9F</td><td>DMA page registers continued</td></tr><tr><td>0A0-0B1 and 0B4-0BF</td><td>Interrupt controller 2, 8259 equivalent</td></tr><tr><td>0B2 and 0B3</td><td>APM control and status port respectively</td></tr><tr><td>0C0-0DF</td><td>DMA controller 2, 8237A-5 equivalent</td></tr><tr><td>0E0-0EF</td><td>Available</td></tr><tr><td>0F0</td><td>Co-processor error register</td></tr><tr><td>0F1</td><td>N/A</td></tr><tr><td>0F2-0F3</td><td>N/A</td></tr><tr><td>0F4</td><td>IDE ID port</td></tr><tr><td>0F5-0F7</td><td>N/A</td></tr><tr><td>0F8</td><td>IDE Index port</td></tr><tr><td>0F9-0FB</td><td>N/A</td></tr><tr><td>0FC</td><td>IDE Data port</td></tr><tr><td>0FD-0FF</td><td>N/A</td></tr><tr><td>100-179</td><td>Available</td></tr><tr><td>180-181</td><td>Default AIM4 SRAM control register (May be remapped)</td></tr><tr><td>182-1EF</td><td>Available</td></tr><tr><td>1F0-1F7</td><td>Primary IDE Controller (AT Drive)</td></tr><tr><td>1FB-22F</td><td>Available</td></tr><tr><td>230 -277</td><td>Available</td></tr></table>

<table><tr><td>Hex Range</td><td>Device</td></tr><tr><td>278-27F</td><td>Parallel Port 2</td></tr><tr><td>280-2F7</td><td>Available</td></tr><tr><td>2F8-2FF</td><td>Serial Port 2</td></tr><tr><td>300-36F</td><td>Available</td></tr><tr><td>370-377</td><td>Alt. Floppy Disk Controller</td></tr><tr><td>378-37F</td><td>Parallel Port 1</td></tr><tr><td>380-3AF</td><td>Available</td></tr><tr><td>3B0-3BB and 3BF</td><td>Mono/VGA mode video</td></tr><tr><td>3BC-3BE</td><td>Reserved for parallel port</td></tr><tr><td>3C0-3DF</td><td>VGA registers</td></tr><tr><td>3E0-3EF</td><td>Available</td></tr><tr><td>3F0-3F7</td><td>Primary Floppy disk controller</td></tr><tr><td>3F8-3FF</td><td>Serial port 1</td></tr><tr><td>4D0</td><td>Master PIC Edge/Level Trigger register</td></tr><tr><td>4D1</td><td>Slave PIC Edge/Level Trigger register</td></tr><tr><td>CF8-CFB</td><td>PCI configuration address register (32 bit I/O only)</td></tr><tr><td>CF9</td><td>Reset Control register (8 bit I/O)</td></tr><tr><td>CFC-CFF</td><td>PCI configuration data register</td></tr><tr><td>400</td><td>Smbus base address for SB.</td></tr><tr><td>480</td><td>GPIO Base Address for SB</td></tr><tr><td>800</td><td>PM (ACPI) Base Address for SB</td></tr><tr><td>860</td><td>Alias for ICH TCO base address.</td></tr><tr><td>0A00~0AFF</td><td>Reserved for SIO functions base address (ex: PME / GPIO etc)</td></tr><tr><td>200-23Fh</td><td>Reserved for ISA.</td></tr><tr><td>240-25Fh</td><td>Reserved for ISA.</td></tr><tr><td>280-28Fh</td><td>Reserved for ISA.</td></tr><tr><td>2A0-2DFh</td><td>Reserved for ISA.</td></tr><tr><td>300-33Fh</td><td>Reserved for ISA.</td></tr><tr><td>380-39Fh</td><td>Reserved for ISA.</td></tr></table>

Table B-3: IO Map

# B.4 Interrupt Request (IRQ) Lines

IRQ Lines PIC Mode

<table><tr><td>IRQ#</td><td>Typical Interrupt Resource</td><td>Connected to Pin</td><td>Available</td></tr><tr><td>0</td><td>Counter 0</td><td>N/A</td><td>No</td></tr><tr><td>1</td><td>Keyboard controller</td><td>N/A</td><td>No</td></tr><tr><td>2</td><td>Cascade interrupt from slave PIC</td><td>N/A</td><td>No</td></tr><tr><td>3</td><td>Serial Port 2 (COM2) / PCI / ISA</td><td>IRQ3 via SERIRQ, IRQ3 at ISA bus</td><td>Note (1)</td></tr><tr><td>4</td><td>Serial Port 1 (COM1) / PCI / ISA</td><td>IRQ4 via SERIRQ, IRQ4 at ISA bus</td><td>Note (1)</td></tr><tr><td>5</td><td>Parallel Port 2 (LPT2) / PCI / ISA</td><td>IRQ5 via SERIRQ, IRQ5 at ISA bus</td><td>Note (1)</td></tr><tr><td>6</td><td>Floppy Drive Controller</td><td>IRQ6 via SERIRQ</td><td>No</td></tr><tr><td>7</td><td>Parallel Port 1 (LPT1) / PCI / ISA</td><td>IRQ7 via SERIRQ, IRQ7 at ISA bus</td><td>Note (1)</td></tr><tr><td>8</td><td>Real-time clock</td><td>N/A</td><td>No</td></tr><tr><td>9</td><td>SCI / PCI</td><td>IRQ9 via SERIRQ, IRQ9 at ISA bus</td><td>Note (1), (2)</td></tr><tr><td>10</td><td>PCI / ISA</td><td>IRQ10 via SERIRQ, IRQ10 at ISA bus</td><td>Note (1)</td></tr><tr><td>11</td><td>PCI / ISA</td><td>IRQ11 via SERIRQ, IRQ11 at ISA bus</td><td>Note (1)</td></tr><tr><td>12</td><td>PS/2 Mouse / PCI / ISA</td><td>IRQ12 via SERIRQ, IRQ12 at ISA bus</td><td>Note (1)</td></tr><tr><td>13</td><td>Math Processor</td><td>N/A</td><td>No</td></tr><tr><td>14</td><td>Primary IDE controller / PCI / ISA</td><td>IRQ14 via SERIRQ, IRQ14 at ISA bus</td><td>Note (1)</td></tr><tr><td>15</td><td>Secondary IDE controller / PCI / ISA</td><td>IRQ15 via SERIRQ, IRQ15 at ISA bus</td><td>Note (1)</td></tr></table>

Table B-4: IRQ Lines PIC Mode

Note (1): These IRQs can be used for PCI devices when onboard device is disabled. If IRQ is from ISA, user must reserve IRQ for ISA in BIOS setup menu.

Note (2): BIOS does not open IRQ 9 setting for ISA bus.

IRQ Lines APIC Mode

<table><tr><td>IRQ#</td><td>Typical Interrupt Resource</td><td>Connected to Pin</td><td>Available</td></tr><tr><td>0</td><td>Counter 0</td><td>N/A</td><td>No</td></tr><tr><td>1</td><td>Keyboard controller</td><td>N/A</td><td>No</td></tr><tr><td>2</td><td>Cascade interrupt from slave PIC</td><td>N/A</td><td>No</td></tr><tr><td>3</td><td>Serial Port 2 (COM2) / PCI / ISA</td><td>IRQ3 via SERIRQ, IRQ3 at ISA bus</td><td>Note (1)</td></tr><tr><td>4</td><td>Serial Port 1 (COM1) / PCI / ISA</td><td>IRQ4 via SERIRQ, IRQ4 at ISA bus</td><td>Note (1)</td></tr><tr><td>5</td><td>Parallel Port 2 (LPT2) / PCI / ISA</td><td>IRQ5 via SERIRQ, IRQ5 at ISA bus</td><td>Note (1)</td></tr><tr><td>6</td><td>Floppy Drive Controller</td><td>IRQ6 via SERIRQ</td><td>No</td></tr><tr><td>7</td><td>Parallel Port 1 (LPT1) / PCI / ISA</td><td>IRQ7 via SERIRQ, IRQ7 at ISA bus</td><td>Note (1)</td></tr><tr><td>8</td><td>Real-time clock</td><td>N/A</td><td>No</td></tr><tr><td>9</td><td>SCI / PCI</td><td>IRQ9 via SERIRQ, IRQ9 at ISA bus</td><td>Note (1), (2)</td></tr><tr><td>10</td><td>PCI / ISA</td><td>IRQ10 via SERIRQ, IRQ10 at ISA bus</td><td>Note (1)</td></tr><tr><td>11</td><td>PCI / ISA</td><td>IRQ11 via SERIRQ, IRQ11 at ISA bus</td><td>Note (1)</td></tr><tr><td>12</td><td>PS/2 Mouse / PCI / ISA</td><td>IRQ12 via SERIRQ, IRQ12 at ISA bus</td><td>Note (1)</td></tr><tr><td>13</td><td>Math Processor</td><td>N/A</td><td>No</td></tr><tr><td>14</td><td>Primary IDE controller / PCI / ISA</td><td>IRQ14 via SERIRQ, IRQ14 at ISA bus</td><td>Note (1)</td></tr><tr><td>15</td><td>Secondary IDE controller / PCI / ISA</td><td>IRQ15 via SERIRQ, IRQ15 at ISA bus</td><td>Note (1)</td></tr><tr><td>16</td><td>N/A</td><td>PCI Slot 1/2/3/4, PCIE Port 0/1/2/3/4/5 UHCI Controller 4/6, PEG Root Port, I.G.D</td><td>Yes</td></tr><tr><td>17</td><td>N/A</td><td>PCI Slot 1/2/3/4, PCIE Port 0/1/2/3/4/5, PEG Root Port,</td><td>Yes</td></tr></table>

<table><tr><td>IRQ#</td><td>Typical Interrupt Resource</td><td>Connected to Pin</td><td>Available</td></tr><tr><td>18</td><td>N/A</td><td>PCI Slot 1/2/3/4, PCIE Port 0/1/2/3/4/5 UHCI Controller 3, PEG Root Port, SATA Host controller, SMBus Controller, Thermal Controller, EHCI Controller #2</td><td>Yes</td></tr><tr><td>19</td><td>N/A</td><td>PCI Slot 1/2/3/4, PCIE Port 0/1/2/3/4/5 UHCI Controller 2/7, PEG Root Port, SATA Host controller, SATA Host controller#1,</td><td>Yes</td></tr><tr><td>20</td><td>N/A</td><td>ICH9 internal GBE controller</td><td>No</td></tr><tr><td>21</td><td>N/A</td><td>UHCI Controller 5</td><td>No</td></tr><tr><td>22</td><td>N/A</td><td>ICH9 HDA</td><td>No</td></tr><tr><td>23</td><td>N/A</td><td>UHCI Controller 1, EHCI Controller 1</td><td>No</td></tr></table>

Table B-5: IRQ Lines APIC Mode

Note (1): These IRQs can be used for PCI devices when onboard device is disabled. If IRQ is from ISA, user must reserve IRQ for ISA in BIOS setup menu.

Note (2): BIOS does not open IRQ 9 setting for ISA bus.

PCI Interrupt Request Routing

<table><tr><td>Bus #</td><td>Device #</td><td>Function #</td><td>Routing</td><td>Description</td></tr><tr><td>00h</td><td>00h</td><td>00h</td><td>N/A</td><td>Intel 965 GME GMCH Host-Hub Interface Bridge</td></tr><tr><td>00</td><td>01H</td><td>00H</td><td>Internal</td><td>PEG. Root Port</td></tr><tr><td>02</td><td>00H</td><td>0FFH</td><td>N/A</td><td>PEG. Port</td></tr><tr><td>00h</td><td>02h</td><td>00h</td><td>Internal</td><td>Intel Integrated Graphics Device</td></tr><tr><td>00h</td><td>02h</td><td>01h</td><td>Internal</td><td>Intel Integrated Graphics Device (Function 1)</td></tr><tr><td>00h</td><td>19h</td><td>00h</td><td>Internal</td><td>GbE Controller</td></tr><tr><td>00h</td><td>1Ah</td><td>00h</td><td>Internal</td><td>Intel USB UHCI Controller 4</td></tr><tr><td>00h</td><td>1Ah</td><td>01h</td><td>Internal</td><td>Intel USB UHCI Controller 5</td></tr><tr><td>00h</td><td>1Ah</td><td>02h</td><td>Internal</td><td>Intel USB UHCI Controller 7</td></tr><tr><td>00h</td><td>1Ah</td><td>07h</td><td>Internal</td><td>Intel USB EHCI Controller 2</td></tr><tr><td>00h</td><td>1Bh</td><td>00h</td><td>Internal</td><td>High Definition Audio controller</td></tr><tr><td>00h</td><td>1Ch</td><td>00h</td><td>Internal</td><td>Intel ICH Express Root port 0</td></tr><tr><td>00h</td><td>1Ch</td><td>01h</td><td>Internal</td><td>Intel ICH Express Root port 1</td></tr><tr><td>00h</td><td>1Ch</td><td>02h</td><td>Internal</td><td>Intel ICH Express Root port 2</td></tr><tr><td>00h</td><td>1Ch</td><td>03h</td><td>Internal</td><td>Intel ICH Express Root port 3</td></tr><tr><td>00h</td><td>1Ch</td><td>04h</td><td>Internal</td><td>Intel ICH Express Root port 4</td></tr><tr><td>00h</td><td>1Ch</td><td>05h</td><td>Internal</td><td>Intel ICH Express Root port 5</td></tr><tr><td>00h</td><td>1Dh</td><td>00h</td><td>Internal</td><td>Intel USB UHCI Controller 1</td></tr><tr><td>00h</td><td>1Dh</td><td>01h</td><td>Internal</td><td>Intel USB UHCI Controller 2</td></tr><tr><td>00h</td><td>1Dh</td><td>02h</td><td>Internal</td><td>Intel USB UHCI Controller 3</td></tr><tr><td>00h</td><td>1Dh</td><td>03h</td><td>Internal</td><td>Intel USB UHCI Controller 6</td></tr><tr><td>00h</td><td>1Dh</td><td>07h</td><td>Internal</td><td>Intel USB EHCI Controller 1</td></tr><tr><td>00h</td><td>1Eh</td><td>00h</td><td>N/A</td><td>Intel Hub Interface to PCI Bridge</td></tr><tr><td>00h</td><td>1Fh</td><td>00h</td><td>N/A</td><td>Intel LPC Interface Bridge</td></tr><tr><td>00h</td><td>1Fh</td><td>02h</td><td>Internal</td><td>Intel SATA Host /Raid controller</td></tr><tr><td>00h</td><td>1Fh</td><td>03h</td><td>Internal</td><td>Intel SMBus Controller</td></tr><tr><td>00h</td><td>1Fh</td><td>05h</td><td>Internal</td><td>Intel Host SATA controller1</td></tr><tr><td>00h</td><td>1Fh</td><td>06h</td><td>Internal</td><td>Thermal Controller</td></tr><tr><td>01h</td><td>07h</td><td>0FFh</td><td>external</td><td>ITE8888 PCI to ISA bridge</td></tr><tr><td>01h</td><td>0Ch</td><td>0FFh</td><td>external</td><td>PCI slot 4</td></tr></table>

<table><tr><td>Bus #</td><td>Device #</td><td>Function #</td><td>Routing</td><td>Description</td></tr><tr><td>01h</td><td>0Dh</td><td>0FFh</td><td>external</td><td>PCI slot 3</td></tr><tr><td>01h</td><td>0Eh</td><td>0FFh</td><td>external</td><td>PCI slot 2</td></tr><tr><td>01h</td><td>0Fh</td><td>0FFh</td><td>external</td><td>PCI slot 1</td></tr><tr><td>04h</td><td>00h</td><td>0FFh</td><td>Internal</td><td>PCIE Port #0</td></tr><tr><td>05h</td><td>00h</td><td>0FFh</td><td>Internal</td><td>PCIE Port #1</td></tr><tr><td>06h</td><td>00h</td><td>0FFh</td><td>Internal</td><td>PCIE Port #2</td></tr><tr><td>07h</td><td>00h</td><td>0FFh</td><td>Internal</td><td>PCIE Port #3</td></tr><tr><td>08h</td><td>00h</td><td>0FFh</td><td>Internal</td><td>PCIE Port #4</td></tr><tr><td>09h</td><td>00h</td><td>0FFh</td><td>Internal</td><td>PCIE Port #5</td></tr></table>

Table B-6: PCI Interrupt Request Routing

PCI Interrupt Routing Map

<table><tr><td>PIRQ</td><td>A</td><td>B</td><td>C</td><td>D</td><td>E</td><td>F</td><td>G</td><td>H</td></tr><tr><td>INT Line</td><td>INTA</td><td>INTB</td><td>INTC</td><td>INTD</td><td></td><td></td><td></td><td></td></tr><tr><td>PEG Root Port</td><td>INTA</td><td>INTB</td><td>INTC</td><td>INTD</td><td></td><td></td><td></td><td></td></tr><tr><td>VGA</td><td>X</td><td></td><td></td><td></td><td></td><td></td><td></td><td></td></tr><tr><td>SATA Controller</td><td></td><td></td><td>X</td><td>X</td><td></td><td></td><td></td><td></td></tr><tr><td>SATA Controller1</td><td></td><td></td><td></td><td>X</td><td></td><td></td><td></td><td>X</td></tr><tr><td>SMBUS Controller</td><td></td><td></td><td>X</td><td></td><td></td><td></td><td></td><td></td></tr><tr><td>Thermal Controller</td><td></td><td></td><td>X</td><td></td><td></td><td></td><td></td><td></td></tr><tr><td>UHCI 1</td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td>X</td></tr><tr><td>UHCI 2</td><td></td><td></td><td></td><td>X</td><td></td><td></td><td></td><td></td></tr><tr><td>UHCI 3</td><td></td><td></td><td>X</td><td></td><td></td><td></td><td></td><td></td></tr><tr><td>UHCI 4</td><td>X</td><td></td><td></td><td></td><td></td><td></td><td></td><td></td></tr><tr><td>UHCI 5</td><td></td><td></td><td></td><td></td><td></td><td>X</td><td></td><td></td></tr><tr><td>UHCI 6</td><td>X</td><td></td><td></td><td></td><td></td><td></td><td></td><td>X</td></tr><tr><td>UHCI 7</td><td></td><td></td><td></td><td>X</td><td></td><td></td><td></td><td></td></tr><tr><td>EHCI 1</td><td></td><td></td><td></td><td></td><td></td><td></td><td></td><td>X</td></tr><tr><td>EHCI 2</td><td></td><td></td><td>X</td><td></td><td></td><td></td><td></td><td></td></tr><tr><td>HDA</td><td></td><td></td><td></td><td></td><td></td><td></td><td>X</td><td></td></tr><tr><td>Intel GBE</td><td></td><td></td><td></td><td></td><td>X</td><td></td><td></td><td></td></tr><tr><td>PCIE port 0</td><td>INTA</td><td>INTB</td><td>INTC</td><td>INTD</td><td></td><td></td><td></td><td></td></tr><tr><td>PCIE port 1</td><td>INTB</td><td>INTC</td><td>INTD</td><td>INTA</td><td></td><td></td><td></td><td></td></tr><tr><td>PCIE port 2</td><td>INTC</td><td>INTD</td><td>INTA</td><td>INTB</td><td></td><td></td><td></td><td></td></tr><tr><td>PCIE port 3</td><td>INTD</td><td>INTA</td><td>INTB</td><td>INTC</td><td></td><td></td><td></td><td></td></tr><tr><td>PCIE port 4</td><td>INTA</td><td>INTB</td><td>INTC</td><td>INTD</td><td></td><td></td><td></td><td></td></tr><tr><td>PCIE port 5</td><td>INTB</td><td>INTC</td><td>INTD</td><td>INTA</td><td></td><td></td><td></td><td></td></tr><tr><td>PCI Slot1</td><td>INTB</td><td>INTC</td><td>INTD</td><td>INTA</td><td></td><td></td><td></td><td></td></tr><tr><td>PCI Slot2</td><td>INTC</td><td>INTD</td><td>INTA</td><td>INTB</td><td></td><td></td><td></td><td></td></tr><tr><td>PCI Slot3</td><td>INTD</td><td>INTA</td><td>INTB</td><td>INTC</td><td></td><td></td><td></td><td></td></tr><tr><td>PCI Slot4</td><td>INTA</td><td>INTB</td><td>INTC</td><td>INTD</td><td></td><td></td><td></td><td></td></tr></table>

Table B-7: PCI Interrupt Routing Map

# Important Safety Instructions

For user safety, please read and follow all instructions, WARNINGS, CAUTIONS, and NOTES marked in this manual and on the associated equipment before handling/operating the equipment.

▶ Read these safety instructions carefully.
- Keep this user’s manual for future reference.
▶ Read the specifications section of this manual for detailed information on the operating environment of this equipment.
▶ When installing/mounting or uninstalling/removing equipment:

▷ Turn off power and unplug any power cords/cables.

▶ To avoid electrical shock and/or damage to equipment:

▷ Keep equipment away from water or liquid sources;
▷ Keep equipment away from high heat or high humidity;
▷ Keep equipment properly ventilated (do not block or cover ventilation openings);

▶ Make sure to use recommended voltage and power source settings;

▶ Always install and operate equipment near an easily accessible electrical socket-outlet;

▷ Secure the power cord (do not place any object on/over the power cord);

▶ Only install/attach and operate equipment on stable surfaces and/or recommended mountings; and,

▷ If the equipment will not be used for long periods of time, turn off and unplug the equipment from its power source.

▶ Never attempt to fix the equipment. Equipment should only be serviced by qualified personnel.

A Lithium-type battery may be provided for uninterrupted, backup or emergency power.

![The image displays a triangular warning sign with a dark red background and a large white exclamation point in the center. Below the triangle, the text 'WARNING:' is printed in black capital letters.](.nupro-935a-50-13060-1030-204-en/44d0b05447a33de5ca2aa8edafb0e88a2c1aa8593a345833acacb77e96573925.jpg)

Risk of explosion if battery is replaced with one of an incorrect type. Dispose of used batteries appropriately.

▶ Equipment must be serviced by authorized technicians when:

▷ The power cord or plug is damaged;
▷ Liquid has penetrated the equipment;
▷ It has been exposed to high humidity/moisture;
$\triangleright$ It is not functioning or does not function according to the user's manual;
▷ It has been dropped and/or damaged; and/or,
▷ It has an obvious sign of breakage.

# Getting Service

Contact us should you require any service or assistance.

# ADLINK Technology, Inc.

Address: 9F, No.166 Jian Yi Road, Zhonghe District
New Taipei City 235, Taiwan
新北市中和區建一路 166 號 9 樓

Tel: +886-2-8226-5877

Fax: +886-2-8226-5717

Email: service@adlinktech.com

# Ampro ADLINK Technology, Inc.

Address: 5215 Hellyer Avenue, #110, San Jose, CA 95138, USA

Tel: +1-408-360-0200

Toll Free: +1-800-966-5200 (USA only)

Fax: +1-408-360-0222

Email: info@adlinktech.com

# ADLINK Technology (China) Co., Ltd.

Address: 上海市浦东新区张江高科技园区芳春路 300 号 (201203)
300 Fang Chun Rd., Zhangjiang Hi-Tech Park,
Pudong New Area, Shanghai, 201203 China

Tel: +86-21-5132-8988

Fax: +86-21-5132-3588

Email: market@adlinktech.com

# ADLINK Technology Beijing

Address: 北京市海淀区上地东路 1 号盈创动力大厦 E 座 801 室(100085)
Rm. 801, Power Creative E, No. 1, B/D
Shang Di East Rd., Beijing, 100085 China

Tel: +86-10-5885-8666

Fax: +86-10-5885-8625

Email: market@adlinktech.com

# ADLINK Technology Shenzhen

Address: 深圳市南山区科技园南区高新南七道 数字技术园
A1 栋 2 楼 C 区 (518057)
2F, C Block, Bldg. A1, Cyber-Tech Zone, Gao Xin Ave. Sec. 7,
High-Tech Industrial Park S., Shenzhen, 518054 China

Tel: +86-755-2643-4858

Fax: +86-755-2664-6353

Email: market@adlinktech.com

# ADLINK Technology (Europe) GmbH

Address: Nord Carree 3, 40477 Duesseldorf, Germany

Tel: +49-211-495-5552

Fax: +49-211-495-5557

Email: emea@adlinktech.com

# ADLINK Technology, Inc. (French Liaison Office)

Address: 15 rue Emile Baudot, 91300 Massy CEDEX, France

Tel: +33 (0) 1 60 12 35 66

Fax: +33 (0) 1 60 12 35 66

Email: france@adlinktech.com

# ADLINK Technology Japan Corporation

Address: 〒101-0045 東京都千代田区神田鍛冶町 3-7-4

神田 374 ビル 4F

KANDA374 Bldg. 4F, 3-7-4 Kanda Kajicho,

Chiyoda-ku, Tokyo 101-0045, Japan

Tel: +81-3-4455-3722

Fax: +81-3-5209-6013

Email: japan@adlinktech.com

# ADLINK Technology, Inc. (Korean Liaison Office)

Address: 서울시 서초구 서초동 1506-25 한도 B/D 2 층

2F, Hando B/D, 1506-25, Seocho-Dong, Seocho-Gu,

Seoul 137-070, Korea

Tel: +82-2-2057-0565

Fax: +82-2-2057-0563

Email: korea@adlinktech.com

# ADLINK Technology Singapore Pte. Ltd.

Address: 84 Genting Lane #07-02A, Cityneon Design Centre,

Singapore 349584

Tel: +65-6844-2261

Fax: +65-6844-2263

Email: singapore@adlinktech.com

# ADLINK Technology Singapore Pte. Ltd. (Indian Liaison Office)

Address: No. 1357, "Anupama", Sri Aurobindo Marg, 9th Cross,

JP Nagar Phase I, Bangalore - 560078, India

Tel: +91-80-65605817

Fax: +91-80-22443548

Email: india@adlinktech.com
[🔗 Link to the original document](.nupro-935a-50-13060-1030-204-en/nupro-935a-50-13060-1030-204-en.pdf)