# NuPRO-E47

PICMG $^{®}$ 1.3 Full Size LGA1700 Intel $^{®}$ Core $^{TM}$

i9/i7/i5/i3 Processor-Based SHB

User's Manual

![Green printed circuit board with various electronic components and connectors (no readable text or symbols)](.nupro-e47-50m-41810-1000-10/92874dcbc904ca73b90e8b4301146aa71b2c9cdcc45012aefb5509229bb43f2d.jpg)

Manual Rev.: 1.0

Revision Date: March 04, 2024

Part No: 50M-41810-1000

# Revision History

<table><tr><td>Revision</td><td>Release Date</td><td>Description of Change(s)</td></tr><tr><td>1.0</td><td>March 04, 2024</td><td>Initial release</td></tr></table>

# Preface

# Copyright 2024 ADLINK Technology, Inc.

This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer.

# Disclaimer

The information in this document is subject to change without prior notice in order to improve reliability, design, and function and does not represent a commitment on the part of the manufacturer.

In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.

# Environmental Responsibility

ADLINK is committed to fulfill its social responsibility to global environmental preservation through compliance with the European Union's Restriction of Hazardous Substances (RoHS) directive and Waste Electrical and Electronic Equipment (WEEE) directive. Environmental protection is a top priority for ADLINK. We have enforced measures to ensure that our products, manufacturing processes, components, and raw materials have as little impact on the environment as possible. When products are at their end of life, our customers are encouraged to dispose of them in accordance with the product disposal and/or recovery programs prescribed by their nation or company.

# Trademarks

Product names mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks of their respective companies.

# Conventions

Take note of the following conventions used throughout this manual to make sure that users perform certain tasks and instructions properly.

![The image displays an icon of a white document with a folded upper-left corner and horizontal black lines representing text. A large, bold red checkmark is superimposed diagonally over the document. There is no actual text.](.nupro-e47-50m-41810-1000-10/96341dde68ca93702f6d15cc79ac03e08629c1af4a62fbf6b83a18a1dc096deb.jpg)
NOTE:

Additional information, aids, and tips that help users perform tasks.

![The image displays a yellow triangular warning sign containing a black exclamation mark in the center.](.nupro-e47-50m-41810-1000-10/296a0bb06eac54e28486cc0d49fc4ea796f9075f211479c9d4127ceaedf7b820.jpg)
CAUTION:

Information to prevent minor physical injury, component damage, data loss, and/or program corruption when trying to complete a task.

![The image features a dark red, upward-pointing triangle containing a white exclamation mark in its center. A thin black horizontal line runs across the very top edge of the triangle.](.nupro-e47-50m-41810-1000-10/da2354094d77871490e0518f38ec432ca142212327f26309ad3a0dd912279b5a.jpg)
WARNING:

Information to prevent serious physical injury, component damage, data loss, and/or program corruption when trying to complete a specific task.

# Table of Contents

# Preface.... iii

# List of Figures ...... vii

# List of Tables ix

# 1 Introduction ...... 1

1.1 Overview.... 1
1.2 Features.... 1
1.3 Specifications.... 2
1.4 Block Diagram 5
1.5 Schematics and Dimensions 6
1.6 I/O Connectivity 6
1.7 Rear Panel I/O Ports 8
1.8 Board Layout 10
1.9 Onboard Connectors 12
1.10 Jumpers & Switches 20

# 2 Getting Started 21

2.1 Package Contents 21
2.2 Driver Installation 22
2.3 Optional Accessories 23

# A Appendix: BIOS Setup 25

A.1 Entering the BIOS.... 25
A.2 Menu Structure 25
A.3 Main Menu 27
A.4 Advanced Menu 28

A.4.1 CPU Configuration....28
A.4.2 Power Management 30
A.4.3 Serial Console Redirection 30

A.4.4 USB Configuration....32
A.4.5 TPM 2.0 Configuration....33
A.4.6 Onboard Device Configuration 34
A.4.7 NCT6126H Hardware Monitor 36
A.4.8 BIOS Watchdog Timer....37
A.4.9 PCI Express Configuration 38
A.4.10 Miscellaneous....40
A.4.11 Network Stack Configuration 41

A.5 Chipset.... 42

A.5.1 System Agent (SA) Configuration....42
A.5.2 PCH-IO Configuration....44

A.6 Security 47

A.6.1 Secure Boot menu 48
A.6.2 Security Configuration 48

A.7 Boot 49
A.8 Save & Exit 53
A.9 MEBx 54

# Important Safety Instructions.... 55

# Getting Service 57

# List of Figures

Figure 1-1: NuPRO-E47 Block Diagram ....5
Figure 1-2: Board Dimensions ...... 6
Figure 1-3: Rear Panel I/O Ports....8
Figure 1-4: Board Layout .... 10

This page intentionally left blank.

# List of Tables

Table 1-1: NuPRO-E47 I/O Connectivity ...... 7
Table 1-2: Rear Panel I/O Legend 8
Table 1-3: Board Layout Legend ...... 11

This page intentionally left blank.

# 1 Introduction

# 1.1 Overview

The ADLINK NuPRO-E47 is a PICMG 1.3 System Host Board (SHB) supporting the 12th Generation Intel® Core™ i9/i7/i5/i3 and Pentium® processors in LGA1700 package to deliver a scalable high performance platform for a wide array of industrial applications. The NuPRO-E47 supports 10nm process CPUs at up to 5.0 GHz with integrated graphics and memory controllers and Direct Media Interface (DMI) connectivity to the Intel® Q670E Express chipset. Dual-channel DDR5 memory is supported up to a maximum of 64GB on two DIMM slots.

These advanced features, coupled with PCI Express® x16 expansion capability, dual PCI Express®-based Gigabit Ethernet, SATA 6 Gb/s and USB 3.2 support make the NuPRO-E47 ideal for vision and automation control applications.

# 1.2 Features

▶ Supports Intel® Core™ i9/i7/i5/i3 and Pentium® processors in LGA1700 package

▶ Integrated Intel® HD Graphics

PCI Express® x16 expansion capability via backplane

▶ Dual 2.5-Gigabit Ethernet

▶ 10x USB 3.x ports (3x USB 3.2 Gen2 x1 ports on rear panel, 7x USB 3.2 Gen1 x1 headers on SHB)

▶ 4x USB 2.0 ports on backplane

▶ 6x SATA 6 Gb/s ports on SHB

▶ 4x COM ports (including 2x RS232/422/485)

▶ 1x HDMI on rear panel

▶ 1x DVI-D header on SHB

▶ 1x VGA header on SHB

▶ 1x M.2 M-Key, 2280, supporting PCIe Gen4 x4

▶ 1x LPT port

▶ Watchdog timer, hardware monitor
▶ Optional HD audio kit (DB-Audio2 daughter board)
▶ TPM2.0
▶ RoHS compliant

![The image shows a white document icon with a folded top-right corner and faint horizontal lines. A large, bold red checkmark is superimposed over the document.](.nupro-e47-50m-41810-1000-10/7ed404b07f8c551513d5ccb42de0a2c538c2cf4f8f8d35278dd5e053c5ae85c2.jpg)
NOTE:

To purchase the optional DB-Audio2 daughter board, please contact your ADLINK sales representative.

# 1.3 Specifications

Processor& System

<table><tr><td>CPU</td><td>Intel® CoreTM i9-12900E, up to 5.0 GHz, 16 Cores, 30M Cache, 65W TDPIntel® CoreTM i9-12900TE, up to 4.8 GHz, 16 Cores, 30M Cache, 35W TDPIntel® CoreTM i7-12700E, up to 4.8 GHz, 12 Cores, 25M Cache, 65W TDPIntel® CoreTM i7-12700TE, up to 4.7 GHz, 12 Cores, 25M Cache, 35W TDPIntel® CoreTM i5-12500E, up to 4.5 GHz, 6 Cores, 18M Cache, 65W TDPIntel® CoreTM i5-12500TE, up to 4.3 GHz, 6 Cores, 18M Cache, 35W TDPIntel® CoreTM i3-12100E, up to 4.2 GHz, 4 Cores, 12M Cache, 60W TDPIntel® CoreTM i3-12100TE, up to 4.0 GHz, 4 Cores, 12M Cache, 35W TDPIntel® Pentium® Gold G7400E, up to 3.6 GHz, 2 Cores, 6M Cache, 46W TDPIntel® Pentium® Gold G7400TE, up to 3.0 GHz, 2 Cores, 6M Cache, 35W TDPIntel® Celeron® G6900E, up to 3.0 GHz, 2 Cores, 4M Cache, 46W TDPIntel® Celeron® G6900TE, up to 2.4 GHz, 2 Cores, 4M Cache, 35W TDP</td></tr><tr><td>Chipset</td><td>Intel® Q670E</td></tr></table>

<table><tr><td>Memory</td><td>Dual channel DDR5 4800 MHz, up to 64GB</td></tr><tr><td>BIOS</td><td>AMI® UEFI BIOS256 Mbit SPI flash memory</td></tr><tr><td>TPM</td><td>Infineon TPM SLB 9670XQ2.0 or 9670VQ2.0</td></tr><tr><td>WDT</td><td>1-255 sec. or 1-255 min. software programmable, can generate system reset</td></tr><tr><td>Hardware Monitor</td><td>CPU temperature, system temperature, system voltage, CPU fan speed</td></tr><tr><td>OS</td><td>Microsoft® Windows® 10 64-bit (Windows 10 IoT Enterprise LTSC 21H2 19044)Microsoft® Windows® 11 64-bit (Windows 11 IoT Enterprise 22H2 22621)Ubuntu 20.04.6 64-bit</td></tr></table>

I/O

<table><tr><td>Serial ATA</td><td>6x SATA 3.0 onboard with RAID support</td></tr><tr><td>Serial Ports</td><td>2x RS-232 via onboard 2.0 pitch box header2x RS-232/422/485 with auto flow control via onboard 2.0 pitch box header</td></tr><tr><td>PCIe/PCI bus (Via backplane)</td><td>1x PCIe x16 with Intel PCIe slot bifurcation support, can be configured to 1x PCIe x16 or 2x PCIe x8 (based on backplane), 1x PCIe x4 to backplane, and 4x PCI to backplane</td></tr><tr><td>USB</td><td>10x USB 3.x (3x USB 3.2 Gen2 x1 ports on rear I/O &amp; 7x USB 3.2 Gen1 x1 onboard box header)4x USB 2.0 to backplane</td></tr><tr><td>LPT Port</td><td>1x LPT port via onboard box header</td></tr><tr><td>Audio</td><td>1x box header for audio module DB-Audio2</td></tr></table>

Audio

<table><tr><td>Codec</td><td>Realtek® ALC262 support by DB-Audio2 daughter board</td></tr><tr><td>Interface</td><td>Intel® High Definition Audio via onboard box header</td></tr></table>

Display

<table><tr><td>Graphics</td><td>Integrated Intel® HD series, based on CPU for different GPU</td></tr><tr><td>VGA</td><td>1x VGA on rear I/O, resolution up to 1920 x 1200@60Hz</td></tr><tr><td>DVI-D</td><td>1x DVI-D via onboard pin header, resolution up to 1920 x 1200@60Hz</td></tr><tr><td>HDMI</td><td>1x HDMI on rear I/O, resolution up to 4096 x 2160 @ 60Hz</td></tr></table>

Ethernet

<table><tr><td>Controller</td><td>LAN1: Intel® I225-V PHY via RJ45LAN2: Intel® I225-LM via RJ45</td></tr><tr><td>Interface</td><td>2x PCIe x1 bus</td></tr><tr><td>iAMT</td><td>Support iAMT 11 on LAN2</td></tr><tr><td>Wake On LAN</td><td>Support on LAN1 &amp; LAN2</td></tr></table>

Mechanical and Environmental

<table><tr><td>Form Factor</td><td>Full-sized PICMG® 1.3 system host board</td></tr><tr><td>Dimensions</td><td>338 mm x 126 mm (L x W)</td></tr><tr><td>Operating Temperature</td><td>0 to 60°C</td></tr><tr><td>Storage Temperature</td><td>-40 to 80°C</td></tr><tr><td>Certification</td><td>CE &amp; FCC Class A</td></tr><tr><td>Relative Humidity</td><td>5% to 95%, non-condensing</td></tr></table>

# 1.4 Block Diagram

![This flowchart illustrates the architecture of a motherboard based on the Intel Q670E Chipset and an Intel Core Processor.\n\n**Top Section: Processor**\n*   **Central Block:** 'Intel Core i9/i7/i5/i3 Processor (Formally Alder Lake S) LGA 1700 Socket'\n*   **Left Connections (Video):**\n    *   'HDMI' connects via 'DDI' through a 'DP to HDMI1' block.\n    *   'DVI-D' connects via 'DDI'.\n    *   'VGA' connects via 'DDI' through a 'DP to VGA' block.\n*   **Right Connections (Memory & PCIe):**\n    *   'Channel A' and 'Channel B' connect to 'Vertical UDIMM' blocks.\n    *   'PCIe Gen3 x16' connects to 'PICMG 1.3 GF A & B'.\n    *   'PCIe Gen4 x4' connects to 'M.2 M Key'.\n*   **Downward Connection:** A double-headed arrow labeled 'DMI Gen1 x8' connects the Processor to the Chipset below.\n\n**Bottom Section: Chipset**\n*   **Central Block:** 'Intel Q670E Chipset'\n*   **Left Connections (Inputs/Expansion):**\n    *   Two 'RJ45' blocks connect via 'I225-V' and 'I225-LM' respectively (both labeled 'PCIe x1').\n    *   Three 'USB 3.2 (10Gb)' blocks connect via 'USB 3.2 & USB 2.0'.\n    *   One 'USB 3.2 (5Gb)' block connects via 'USB 3.2 & USB 2.0'.\n    *   Four 'USB 3.2 header (5Gb)' blocks connect via 'USB 3.2 & USB 2.0'.\n    *   'PICMG 1.3 GF A' connects via 'PCIe Gen3 x4'.\n    *   'PICMG 1.3 GF C' connects via '4x USB 2.0'.\n    *   'PICMG 1.3 GF D' connects via '4x PCI' through a 'PCle to PCI' block and a 'PCle x1' label.\n    *   'Buzzer' connects directly.\n*   **Right Connections (Outputs/Interfaces):**\n    *   Six 'SATA' lines connect to 'SATA 6Gb' blocks.\n    *   'HD Audio' connects to 'Audio header'.\n    *   An unlabeled line connects to an '8-bit GPIO header'.\n    *   **Super IO Block:** Connected via 'eSPI'. It links to:\n        *   Two 'RS232/422/485 header' blocks.\n        *   Two 'RS232 header' blocks.\n        *   'LTP header'.\n        *   'FAN header'.\n    *   **SPI Connections:**\n        *   Connects to 'TPM'.\n        *   Connects to a 'BUS SW' block.\n        *   The 'BUS SW' block connects to 'BIOS ROM' and 'DB40 Connector' via 'SPI'.](.nupro-e47-50m-41810-1000-10/ca2e2cc8fd19af8bd95a4fbf21ecaf9548c54215e2c9f765ef474b1a48d2c0b8.jpg)

Figure 1-1: NuPRO-E47 Block Diagram

# 1.5 Schematics and Dimensions

![The image displays a square icon containing a white piece of paper with a folded top-right corner and faint horizontal lines. Overlaid on the paper is a large red checkmark. The entire graphic is enclosed within a thin black border.](.nupro-e47-50m-41810-1000-10/be1ca8e0bcc379741c46af6c8b78601abb017f2e216c20c2b0e8ff223aabb479.jpg)
NOTE:

All dimensions shown are in mm (millimeters).

![338.10\n333.60\n173.60\n126.39\n121.47\n104.80\n340.10](.nupro-e47-50m-41810-1000-10/3b045d9b2b9cbc9e2e580820df42206a821e9c140e7b0fd7c5676579443949c7.jpg)

Figure 1-2: Board Dimensions

# 1.6 I/O Connectivity

<table><tr><td>I/O</td><td>Bracket</td><td>Onboard</td><td>Edge Connector</td><td>Remarks</td></tr><tr><td>VGA</td><td>—</td><td>Y</td><td>—</td><td>Cable w/ bracket optional</td></tr><tr><td>DVI-D</td><td>—</td><td>Y</td><td>—</td><td>Cable w/ bracket optional</td></tr><tr><td>LAN1/2 (RJ-45)</td><td>Y</td><td>—</td><td>—</td><td>Act/Link/Speed LEDs</td></tr><tr><td>USB 3.2 Gen2 x1</td><td>3</td><td>—</td><td>—</td><td></td></tr><tr><td>USB 3.2 Gen1 x1</td><td>—</td><td>7</td><td>—</td><td>Cable w/ bracket optional</td></tr><tr><td>USB 2.0</td><td>—</td><td>—</td><td>4</td><td></td></tr></table>

<table><tr><td>I/O</td><td>Bracket</td><td>Onboard</td><td>Edge Connector</td><td>Remarks</td></tr><tr><td>COM</td><td>—</td><td>4</td><td>—</td><td>2.00” pitch</td></tr><tr><td>SATA</td><td>—</td><td>6</td><td>—</td><td>—</td></tr><tr><td>PCIe x4</td><td>—</td><td>—</td><td>Y</td><td>—</td></tr><tr><td>PCIe x16</td><td>—</td><td>—</td><td>Y</td><td>—</td></tr><tr><td>PCI 32bit/33MHz</td><td>—</td><td>—</td><td>Y</td><td>via ITE IT8892</td></tr></table>

Table 1-1: NuPRO-E47 I/O Connectivity

# 1.7 Rear Panel I/O Ports

![A\nB\nC\nD\nE\nF](.nupro-e47-50m-41810-1000-10/1f3970b3e60c94d7006b10c85e3f9e9a19b4ad199633968f30a4d1eee1ed4563.jpg)

Figure 1-3: Rear Panel I/O Ports

<table><tr><td></td><td>Connector</td><td>Description</td></tr><tr><td>A</td><td>LAN2 (RJ-45)</td><td>2.5 Gigabit Ethernet (supports Intel® AMT)</td></tr><tr><td>B</td><td>LAN1 (RJ-45)</td><td>2.5 Gigabit Ethernet</td></tr><tr><td>C/D/E</td><td>USB 3.x x3</td><td>USB 3.2 Gen2 x1 ports</td></tr><tr><td>F</td><td>HDMI</td><td>HDMI connector for LCD monitor</td></tr></table>

Table 1-2: Rear Panel I/O Legend

# USB 3.0 Connectors

![1\n2\n3\n4\n5\n6\n7\n8\n9](.nupro-e47-50m-41810-1000-10/05f37cb0cc97a10fa34c9d23b64f620edf26e5d2224f5b8d84ddb3e9baa9c9c6.jpg)

<table><tr><td>Pin #</td><td>Signal Name</td></tr><tr><td>1</td><td>USB3.0_P5VA</td></tr><tr><td>2</td><td>USB2_CMAN</td></tr><tr><td>3</td><td>USB2_CMAP</td></tr><tr><td>4</td><td>GND</td></tr><tr><td>5</td><td>USB3A_CMRXN</td></tr><tr><td>6</td><td>USB3A_CMRXP</td></tr><tr><td>7</td><td>GND</td></tr><tr><td>8</td><td>USB3A_CMTXN</td></tr><tr><td>9</td><td>USB3A_CMTXP</td></tr></table>

# LAN (RJ-45) Ports

![LED1\nLED2\n8\n1](.nupro-e47-50m-41810-1000-10/cfe05006e6ee5cc8802fa435d752eb9cf46d17511ce3b4a0f2cb2dcc9af64160.jpg)

<table><tr><td>Pin #</td><td>10BASE-T/100BASE-TX</td><td>1000BASE-T</td></tr><tr><td>1</td><td>TX+</td><td>BI_DA+</td></tr><tr><td>2</td><td>TX-</td><td>BI_DA-</td></tr><tr><td>3</td><td>RX+</td><td>BI_DB+</td></tr><tr><td>4</td><td>--</td><td>BI_DC+</td></tr><tr><td>5</td><td>--</td><td>BI_DC-</td></tr><tr><td>6</td><td>RX-</td><td>BI_DB-</td></tr><tr><td>7</td><td>--</td><td>BI_DD+</td></tr><tr><td>8</td><td>--</td><td>BI_DD-</td></tr></table>

<table><tr><td colspan="2">LED1</td><td colspan="2">LED2</td></tr><tr><td>Status</td><td>Description</td><td>Status</td><td>Description</td></tr><tr><td>Off</td><td>No Link</td><td>Off</td><td>10/100 Mb connection</td></tr><tr><td>Yellow</td><td>Linked</td><td>Green</td><td>1 Gb connection</td></tr><tr><td>Blinking</td><td>Data Activity</td><td>Orange</td><td>2.5 Gb connection</td></tr></table>

# HDMI Port

![1\n2\n18\n19](.nupro-e47-50m-41810-1000-10/44272e4f820acb6e08615a98531eceb67a4d6b6ff19ba39a9e68db0b9fe700ec.jpg)

<table><tr><td>Pin #</td><td>Signal</td><td>Pin #</td><td>Signal</td></tr><tr><td>1</td><td>HDMI0_P2</td><td>11</td><td>GND</td></tr><tr><td>2</td><td>GND</td><td>12</td><td>HDMI0_CKN</td></tr><tr><td>3</td><td>HDMI0_N2</td><td>13</td><td>TP_HDMI0_CEC</td></tr><tr><td>4</td><td>DMI0_P1</td><td>14</td><td>NC</td></tr><tr><td>5</td><td>GND</td><td>15</td><td>HDMI0_SCL_SNK</td></tr><tr><td>6</td><td>HDMI0_N1</td><td>16</td><td>HDMI0_SDA_SNK</td></tr><tr><td>7</td><td>HDMI0_P0</td><td>17</td><td>GND</td></tr><tr><td>8</td><td>GND</td><td>18</td><td>P_+5V_S0_HDMI0</td></tr><tr><td>9</td><td>HDMI0_N0</td><td>19</td><td>HDMI0_HPD_SNK</td></tr><tr><td>10</td><td>HDMI0_CKP</td><td></td><td></td></tr></table>

# 1.8 Board Layout

![A B\ni\nh\ng\nf\nC\nD E\nF G H I J K L N P R S T U\nM O Q\nV\nW\nX\ne d c b a Z Y](.nupro-e47-50m-41810-1000-10/d30523c4b7b105cd63169a80255426655dd7dcd6a3ab5f244644447bc65e6551.jpg)

Figure 1-4: Board Layout

<table><tr><td></td><td>Connector</td><td>Description</td></tr><tr><td>A</td><td>CN40</td><td>DIMM B0</td></tr><tr><td>B</td><td>CN38</td><td>DIMM A0</td></tr><tr><td>C</td><td>CN1</td><td>CPU</td></tr><tr><td>D</td><td>FAN1</td><td>CPU fan header</td></tr><tr><td>E</td><td>M2M1</td><td>M.2 M Key</td></tr></table>

<table><tr><td></td><td>Connector</td><td>Description</td></tr><tr><td>F</td><td>CN35</td><td>System panel header</td></tr><tr><td>G</td><td>CN22</td><td>LTP</td></tr><tr><td>H</td><td>CN7</td><td>COM #1</td></tr><tr><td>I</td><td>CN8</td><td>COM #2</td></tr><tr><td>J</td><td>CN9</td><td>COM #3</td></tr><tr><td>K</td><td>CN10</td><td>COM #4</td></tr><tr><td>L</td><td>CN43</td><td>SATA #5</td></tr><tr><td>M</td><td>CN44</td><td>SATA #6</td></tr><tr><td>N</td><td>CN32</td><td>SATA #3</td></tr><tr><td>O</td><td>CN33</td><td>SATA #4</td></tr><tr><td>P</td><td>CN30</td><td>SATA #1</td></tr><tr><td>Q</td><td>CN31</td><td>SATA #2</td></tr><tr><td>R</td><td>CN26</td><td>USB3.0 #4/5</td></tr><tr><td>S</td><td>CN27</td><td>USB3.0 #6/7</td></tr><tr><td>T</td><td>CN28</td><td>USB3.0 #8/9</td></tr><tr><td>U</td><td>USB4</td><td>USB3.0 #10</td></tr><tr><td>V</td><td>CN41</td><td>Clear CMOS</td></tr><tr><td>W</td><td>CN42</td><td>Clear RTC</td></tr><tr><td>X</td><td>CN2</td><td>SMBus pull high voltage jumper (reserved)</td></tr><tr><td>Y</td><td>BT1</td><td>RTC battery</td></tr><tr><td>Z</td><td>VGA1</td><td>VGA header</td></tr><tr><td>a</td><td>CN5</td><td>Audio header</td></tr><tr><td>b</td><td>CN34</td><td>DVI-D header</td></tr><tr><td>c</td><td>DB3</td><td>DB40</td></tr><tr><td>d</td><td>CN50</td><td>Debug header</td></tr><tr><td>e</td><td>DIO</td><td>8-bit GPIO header</td></tr><tr><td>f</td><td>CN49</td><td>PCI BUS 5V/3.3V jumper (reserved)</td></tr><tr><td>g</td><td>FAN2</td><td>System fan header</td></tr><tr><td>h</td><td>PCN1</td><td>IMVP IC FW update jumper</td></tr><tr><td>i</td><td>CN36</td><td>Power 4-pin (ATX 12V)</td></tr></table>

Table 1-3: Board Layout Legend

# 1.9 Onboard Connectors

COM #1 to #4 Connector (RS-232) (CN7/8/9/10)
![1\n2\n9\n10](.nupro-e47-50m-41810-1000-10/f054fa30c19aaf161ad44e1953235801eb814ff7ac3bd1c328c434395d346404.jpg)

<table><tr><td>Pin #</td><td>RS-232 Signal</td></tr><tr><td>1</td><td>DCD</td></tr><tr><td>2</td><td>DSR</td></tr><tr><td>3</td><td>RXD</td></tr><tr><td>4</td><td>RTS</td></tr><tr><td>5</td><td>TXD</td></tr><tr><td>6</td><td>CTS</td></tr><tr><td>7</td><td>DTR</td></tr><tr><td>8</td><td>RI</td></tr><tr><td>9</td><td>GND</td></tr><tr><td>10</td><td>NC</td></tr></table>

<table><tr><td></td><td>COM#1</td><td>COM#2</td><td>COM#3</td><td>COM#4</td></tr><tr><td>Connector</td><td>CN8</td><td>CN7</td><td>CN9</td><td>CN10</td></tr><tr><td>Pitch</td><td>2.00 mm</td><td>2.00 mm</td><td>2.00 mm</td><td>2.00 mm</td></tr></table>

COM #1 to #2 Connector (RS-422/485) (CN7/8)

![1\n2\n9\n10](.nupro-e47-50m-41810-1000-10/e82c5dd51e3d55b62b5b874bd85193e628d600a90c4d367e111253d47f194687.jpg)

<table><tr><td>Pin #</td><td>RS-422</td><td>RS-485</td></tr><tr><td>1</td><td>TXD-</td><td>Data-</td></tr><tr><td>2</td><td>NC</td><td>NC</td></tr><tr><td>3</td><td>TXD+</td><td>Data+</td></tr><tr><td>4</td><td>NC</td><td>NC</td></tr><tr><td>5</td><td>RXD+</td><td>NC</td></tr><tr><td>6</td><td>NC</td><td>NC</td></tr><tr><td>7</td><td>RXD-</td><td>NC</td></tr><tr><td>8</td><td>NC</td><td>NC</td></tr><tr><td>9</td><td>GND</td><td>GND</td></tr><tr><td>10</td><td>NC</td><td>NC</td></tr></table>

# USB 3.0 Connectors (CN26/27/28)

![Pure diagram of a rectangular structure with numbered corners (1 and 20), no text or symbols present.](.nupro-e47-50m-41810-1000-10/4875f51bf2525e74af042e682989e5f437cdfa652fa89785249afd8374595dc8.jpg)

<table><tr><td>Pin #</td><td>Signal</td><td>Pin #</td><td>Signal</td></tr><tr><td>1</td><td>P5V_USB3B</td><td>20</td><td>NC</td></tr><tr><td>2</td><td>S_USB3_RN3_R</td><td>19</td><td>P5V_USB3B</td></tr><tr><td>3</td><td>S_USB3_RP3_R</td><td>18</td><td>S_USB3_RN4_R</td></tr><tr><td>4</td><td>GND</td><td>17</td><td>S_USB3_RP4_R</td></tr><tr><td>5</td><td>S_USB3_TN3_R</td><td>16</td><td>GND</td></tr><tr><td>6</td><td>S_USB3_TP3_R</td><td>15</td><td>S_USB3_TN4_R</td></tr><tr><td>7</td><td>GND</td><td>14</td><td>S_USB3_TP4_R</td></tr><tr><td>8</td><td>S_USB2_N2_R</td><td>13</td><td>GND</td></tr><tr><td>9</td><td>S_USB2_P2_R</td><td>12</td><td>S_USB2_N3_R</td></tr><tr><td>10</td><td>S_USB_OC1#</td><td>11</td><td>S_USB2_P3_R</td></tr></table>

# DVI-D Header (CN34)

<table><tr><td></td><td>Pin #</td><td>Signal</td></tr><tr><td rowspan="20">&lt;img src="images/9473a448e35a6424321687983d1bce394dcbd0b57618053728838792d99d6dc7.jpg"/&gt;</td><td>1</td><td>GND</td></tr><tr><td>2</td><td>GND</td></tr><tr><td>3</td><td>TMD_CKP</td></tr><tr><td>4</td><td>TMD_N2</td></tr><tr><td>5</td><td>TMD_CKN</td></tr><tr><td>6</td><td>TMD_P2</td></tr><tr><td>7</td><td>GND</td></tr><tr><td>8</td><td>GND</td></tr><tr><td>9</td><td>TMD_SCL</td></tr><tr><td>10</td><td>TMD_N1</td></tr><tr><td>11</td><td>TMD_SDA</td></tr><tr><td>12</td><td>TMD_P1</td></tr><tr><td>13</td><td>GND</td></tr><tr><td>14</td><td>GND</td></tr><tr><td>15</td><td>TMD_HPD</td></tr><tr><td>16</td><td>TMD_NO</td></tr><tr><td>17</td><td>+5V_PSU_DVI</td></tr><tr><td>18</td><td>TMD_P0</td></tr><tr><td>19</td><td>GND</td></tr><tr><td>20</td><td>GND</td></tr></table>

VGA Header (VGA1)
![2\n1\n14\n13](.nupro-e47-50m-41810-1000-10/295682f87c2a75ae6c12f9b9f0b808fb1f8d36d53ac9655d065ff9c129d1164f.jpg)

<table><tr><td>Pin #</td><td>Signal</td><td>Pin #</td><td>Signal</td></tr><tr><td>1</td><td>+5V</td><td>8</td><td>Green</td></tr><tr><td>2</td><td>DDC_DAT</td><td>9</td><td>GND</td></tr><tr><td>3</td><td>NC</td><td>10</td><td>Blue</td></tr><tr><td>4</td><td>DDC_CLK</td><td>11</td><td>GND</td></tr><tr><td>5</td><td>GND</td><td>12</td><td>HSYNC</td></tr><tr><td>6</td><td>Red</td><td>13</td><td>GND</td></tr><tr><td>7</td><td>GND</td><td>14</td><td>VSYNC</td></tr></table>

ATX 12V Power Connector (CN36)

![2\n1\n4\n3](.nupro-e47-50m-41810-1000-10/f5d105b27301e6cb309e1490f62d9a193c7cbd4a72c4ee8b84a847b2d6fbb907.jpg)

<table><tr><td>Pin #</td><td>Signal</td></tr><tr><td>1</td><td>GND</td></tr><tr><td>2</td><td>GND</td></tr><tr><td>3</td><td>+12V DC</td></tr><tr><td>4</td><td>+12V DC</td></tr></table>

Serial SATA Connectors (CN30 to 33, CN43, CN44)

![1\n7](.nupro-e47-50m-41810-1000-10/60465d7a61a7ecb6356d6eec52889b7bc9d57b6a832b93fcadd9569c17ebdc44.jpg)

<table><tr><td>Pin #</td><td>Signal</td></tr><tr><td>1</td><td>GND</td></tr><tr><td>2</td><td>TXP</td></tr><tr><td>3</td><td>TXN</td></tr><tr><td>4</td><td>GND</td></tr><tr><td>5</td><td>RXN</td></tr><tr><td>6</td><td>RXP</td></tr><tr><td>7</td><td>GND</td></tr></table>

# Audio Header (CN5)

This connector is designed for use with the ADLINK DB-Audio2 daughter board.

![1\n2\n9\n10](.nupro-e47-50m-41810-1000-10/722ba2e0324a03719537adf09acbf2e2d0aa812aebcefa105ec6050f01e01da7.jpg)

<table><tr><td>Pin #</td><td>Signal</td><td>Function</td></tr><tr><td>1</td><td>GND</td><td>Ground</td></tr><tr><td>2</td><td>AUD_BCLK</td><td>Audio Clock</td></tr><tr><td>3</td><td>GND</td><td>Ground</td></tr><tr><td>4</td><td>ICH_AUD_SDIN1</td><td>Audio Data Input</td></tr><tr><td>5</td><td>P5V</td><td>+ 5V</td></tr><tr><td>6</td><td>ICH_AUD_SDOUT</td><td>Audio Data Output</td></tr><tr><td>7</td><td>P5V_AUD</td><td>+ 5V</td></tr><tr><td>8</td><td>P3V3_DVDD</td><td>3.3V</td></tr><tr><td>9</td><td>AUD_SYNC</td><td>Audio Synchronous</td></tr><tr><td>10</td><td>AUD_RSTJ</td><td>Audio Reset</td></tr></table>

# System Panel Header (CN35)

Connects to chassis-mounted buttons, speakers, and LEDs.

![2\n1\n20\n19](.nupro-e47-50m-41810-1000-10/58d4425daaee3d284599dcffda3d6af3c2c4ef59faf3213fc7e5be5e26d71d80.jpg)

<table><tr><td>Pin #</td><td>Signal</td></tr><tr><td>1</td><td>GND</td></tr><tr><td>2</td><td>SPKR</td></tr><tr><td>3</td><td>RSTBTN</td></tr><tr><td>4</td><td>NC</td></tr><tr><td>5</td><td>NC</td></tr><tr><td>6</td><td>NC</td></tr><tr><td>7</td><td>GND</td></tr><tr><td>8</td><td>+5V_PSU</td></tr><tr><td>9</td><td>PWRBTN</td></tr><tr><td>10</td><td>NC</td></tr><tr><td>11</td><td>NC</td></tr><tr><td>12</td><td>GND</td></tr><tr><td>13</td><td>NC</td></tr><tr><td>14</td><td>KEYLOCK</td></tr><tr><td>15</td><td>HLED</td></tr><tr><td>16</td><td>PLED</td></tr><tr><td>17</td><td>HLED_POWER</td></tr><tr><td>18</td><td>NC</td></tr><tr><td>19</td><td>NC</td></tr><tr><td>20</td><td>+5V_PSU</td></tr></table>

# Fan Header (FAN1, FAN2)

4

![The image displays a black and white line drawing of a piece of furniture, likely a cabinet or dresser. The top section is divided vertically into two columns and horizontally into multiple rows, suggesting several small drawers. The bottom section consists of a single wide drawer spanning the entire width. This wide drawer features four small square knobs arranged in a horizontal row. Additionally, the top right drawer has a small rectangular handle.](.nupro-e47-50m-41810-1000-10/1dcd67e1ed5f2c560be86915be4df0f42f2e3fbbce9e074ef76653a8e3228226.jpg)

<table><tr><td>Pin #</td><td>Signal</td></tr><tr><td>1</td><td>GND</td></tr><tr><td>2</td><td>Fan power (+12V)</td></tr><tr><td>3</td><td>Fan Tachometer</td></tr><tr><td>4</td><td>Fan Speed Control</td></tr></table>

# LTP Header (CN22)

<table><tr><td>25</td><td>1</td></tr><tr><td>26</td><td>2</td></tr></table>

<table><tr><td>Pin #</td><td>Signal</td><td>Pin #</td><td>Signal</td></tr><tr><td>1</td><td>STB-L</td><td>14</td><td>GND</td></tr><tr><td>2</td><td>AFD-L</td><td>15</td><td>PD6</td></tr><tr><td>3</td><td>PD0</td><td>16</td><td>GND</td></tr><tr><td>4</td><td>ERR-L</td><td>17</td><td>PD7</td></tr><tr><td>5</td><td>PD1</td><td>18</td><td>GND</td></tr><tr><td>6</td><td>INIT-L</td><td>19</td><td>ACK-L</td></tr><tr><td>7</td><td>PD2</td><td>20</td><td>GND</td></tr><tr><td>8</td><td>SLIN-L</td><td>21</td><td>BUSY</td></tr><tr><td>9</td><td>PD3</td><td>22</td><td>GND</td></tr><tr><td>10</td><td>GND</td><td>23</td><td>PE</td></tr><tr><td>11</td><td>PD4</td><td>24</td><td>GND</td></tr><tr><td>12</td><td>GND</td><td>25</td><td>SLCT</td></tr><tr><td>13</td><td>PD5</td><td>26</td><td>NC</td></tr></table>

# 8-bit GPIO Header (DIO).

![19 20\n1 2](.nupro-e47-50m-41810-1000-10/25e4a9e41425a091d3c5f93e75a606d5e79e847193d49198d649eea475fa3568.jpg)

<table><tr><td>Pin #</td><td>Signal</td></tr><tr><td>1</td><td>DO0</td></tr><tr><td>2</td><td>DO4</td></tr><tr><td>3</td><td>DO1</td></tr><tr><td>4</td><td>DO5</td></tr><tr><td>5</td><td>DO2</td></tr><tr><td>6</td><td>DO6</td></tr><tr><td>7</td><td>DO3</td></tr><tr><td>8</td><td>DO7</td></tr><tr><td>9</td><td>DI0</td></tr><tr><td>10</td><td>DI4</td></tr><tr><td>11</td><td>DI1</td></tr><tr><td>12</td><td>DI5</td></tr><tr><td>13</td><td>DI2</td></tr><tr><td>14</td><td>DI6</td></tr><tr><td>15</td><td>DI3</td></tr><tr><td>16</td><td>DI7</td></tr><tr><td>17</td><td>GND</td></tr><tr><td>18</td><td>GND</td></tr><tr><td>19</td><td>NC</td></tr><tr><td>20</td><td>NC</td></tr></table>

# 1.10 Jumpers & Switches

# Clear CMOS Jumper (CN41)

To clear the BIOS settings (RTC RST#):

1. Power down and disconnect power from the system.
2. Short pins 2-3 on CN41.
3. Reconnect power and power up the system.
4. Wait 3 seconds or more.
5. Power down and disconnect power from the system.
6. Re-short pins 1-2, and power up the system..

<table><tr><td>CMOS Status</td><td>Connection</td><td>CN41</td></tr><tr><td>Normal</td><td>1 – 2</td><td>&lt;img src="images/1f60d309a8b800acc01a89cc8ff71d4d2f0dc2b8f684a92db79adf7dd118dc36.jpg"/&gt;</td></tr><tr><td>Clear CMOS</td><td>2 – 3</td><td>&lt;img src="images/617c0cc4a9152055199f884cb118eb4d2c0523b55828aea683c21fedb9bb450d.jpg"/&gt;</td></tr></table>

# Clear RTC Jumper (CN42)

To clear the BIOS settings and data/time (SRTCRST#):

1. Power down and disconnect power from the system.
2. Short pins 2-3 on CN42.
3. Reconnect power and power up the system.

After power up, remove the jumper cap from pins 2-3 and reinstall it to pins 1-2.

<table><tr><td>CMOS Status</td><td>Connection</td><td>CN42</td></tr><tr><td>Normal</td><td>1 – 2</td><td>&lt;img src="images/986ad1c519a8a3b8b1557f0a6c54cb5ed2a5249ca53e4b3810d7595e5cb27e2b.jpg"/&gt;</td></tr><tr><td>Clear CMOS</td><td>2 – 3</td><td>&lt;img src="images/1b70ed70513640d25547474db7c1e85576d619e578e2adfa3d0ca34dddccb9e2.jpg"/&gt;</td></tr></table>

To clear CMOS, clear both CMOS and RTC jumpers at the same time.

# 2 Getting Started

# 2.1 Package Contents

Before unpacking, check the shipping carton for any damage. If the shipping carton and/or contents are damaged, inform your dealer immediately. Retain the shipping carton and packing materials for inspection. Obtain authorization from the dealer before returning any product to ADLINK.

▶ NuPRO-E47
▶ SATA data cable with latch (x2)
▶ 2-port USB 3.0 cable with bracket (2.0 mm pitch)
▶ 2-port COM cable with bracket (2.0 mm pitch)
▶ Printer port cable with bracket (2.0 mm pitch)

![The image features a red triangle containing a white exclamation point, positioned above the text 'WARNING:' printed in black, uppercase letters.](.nupro-e47-50m-41810-1000-10/57367cf3e90df85a491f1c6c7e0a69327838a186b9135cf95dfe101a1a999064.jpg)

The NuPRO-E47 must be protected from static discharge and physical shock. Never remove any of the socketed parts except at a static-free workstation. Use the anti-static bag shipped with the product to handle the board. Wear a grounded wrist strap when installing and/or servicing.

# 2.2 Driver Installation

Download requisite drivers, as follows, for your system from http://www.adlinktech.com and install.

Intel® Chipset Device Software
Intel® Management Engine Components
Intel® UHD Graphics Driver
Intel® SerialIO Driver
Intel® Network Connections Drivers
Intel® HID Event Filter
Intel® Dynamic Tuning Technology
Intel® GNA
Intel® PPM
Intel® Rapid Storage Technology
▶ Realtek Audio ALC262

![The image shows a red triangular warning sign with a white border. Inside the triangle is a large white exclamation point in the center.](.nupro-e47-50m-41810-1000-10/155e366883eca7c69cdefc0ce39fda1c15d0ed21967dc70b4e9da7c355491bea.jpg)
WARNING:

In order to enable RAID or AHCI mode, you must pre-install the Intel® Rapid Storage Technology driver during the Windows\* installation process. using the F6 installation method.

# 2.3 Optional Accessories

ADLINK offers optional accessories for NuPRO-E47. Please contact ADLNIK sales representatives for details.

▶ DB-Audio2 (high-definition audio) 91-49030-0010
▶ LGA1700 1U CPU cooler 32-21002-0000-A0
▶ LGA1700 2U CPU cooler 32-20976-1000-A0
▶ DVI-D/VGA cable with bracket 30-25309-0000-A0
▶ 4-port USB 3.0 cable with bracket 30-25305-0020-A0
▶ 2-port USB 3.0 cable (right angle) with bracket 30-25046-0110-A0
▶ 1-port COM cable with bracket 30-25003-2100
▶ DIO cable with bracket 30-25304-0000-B0

This page intentionally left blank.

# Appendix A BIOS Setup

The following chapter describes basic navigation for the AMIBIOS $^{®}$ EFI BIOS setup utility.

# A.1 Entering the BIOS

To enter the setup screen, follow these steps:

1. Power on the motherboard
2. Press &lt; Delete &gt; when the prompt appears:

# A.2 Menu Structure

This section presents the seven primary menus of the BIOS Setup Utility. Use the following table as a quick reference for the contents of the BIOS Setup Utility. The subsections in this section describe the submenus and setting options for each menu item. The default setting options are presented in bold, and the function of each setting is described in the right hand column of the respective table.

indicates a submenu

Gray text indicates info only

Bold italics font indicates default setting

<table><tr><td>Main</td><td>Advanced</td><td>Chipset</td><td>Security</td></tr><tr><td>- System Date- System Time</td><td>► CPUConfiguration► Power Management► Serial Console Redirection► USB Configuration► TPM 2.0 Configuration► Onboard Devices Configuration► NCT6106D HW Monitor► BIOS Watchdog Timer► PCIe Express Configuration► Miscellaneous► Network Stake Configuration► Intel® Ethernet Controller (3) I225-V► Intel® Ethernet Controller (3) I225-LM</td><td>► System Agent (SA)Configuration► PCH-I/O Configuration- PCH digital I/O device</td><td>- Administrator Password- User Password► Secure Boot menu► Security Configuration</td></tr></table>

<table><tr><td>Boot</td><td>Save &amp; Exit</td><td>MEBx</td></tr><tr><td>- Setup PromptTimeout- BootupNumLock State- Quiet Boot- Fast Boot- Boot Option #1- Boot Option #2- Boot Option #3- Boot Option #4- Boot Option #5- Boot Option #6- Boot Option #7- Boot Option #8- Boot Option #9- Boot Option #10- Boot Option #11</td><td>- Save Changes and Exit- DiscardChanges and Exit- Save Changes and Reset- DiscardChanges and Reset- Save Changes- DiscardChanges- RestoreDefaults- Save as User Defaults- Restore User Defaults- Launch EFIShell from file system device</td><td>- Intel(R) ME Password</td></tr></table>

# A.3 Main Menu

The Main Menu provides read-only information about your system and also allows you to set the System Date and Time

<table><tr><td>Feature</td><td>Option</td><td>Description</td></tr><tr><td>System Date</td><td>xxx mm/dd/yyyy</td><td rowspan="2">Sets the date and time. Use Tab to switch between elements.</td></tr><tr><td>System Time</td><td>hh:mm:ss</td></tr></table>

# A.4 Advanced Menu

This menu contains the settings for most of the user interfaces in the system.

<table><tr><td>Feature</td><td>Description</td></tr><tr><td>▶ CPU Configuration</td><td>CPU Configuration</td></tr><tr><td>▶ Power Management</td><td>System ACPI Parameters</td></tr><tr><td>▶ Serial Console Redirection</td><td>Serial Console Redirection</td></tr><tr><td>▶ USB Configuration</td><td>USB Configuration Parameters</td></tr><tr><td>▶ TPM 2.0 Configuration</td><td>TPM 2.0 Configuration</td></tr><tr><td>▶ Onboard Devices Configuration</td><td>Onboard Device Parameters</td></tr><tr><td>▶ NCT6106D HW Monitor</td><td>Monitor hardware status</td></tr><tr><td>▶ BIOS Watchdog Timer</td><td>BIOS Watch Dog Configuration</td></tr><tr><td>▶ PCI Express Configuration</td><td>PCI Express Configuration settings</td></tr><tr><td>▶ Miscellaneous</td><td>Miscellaneous</td></tr><tr><td>▶ Network Stake</td><td>Network Stack Settings</td></tr><tr><td>▶ Intel® Ethernet Controller I225-V</td><td rowspan="2">Configure Gigabit Ethernet device parameters</td></tr><tr><td>▶ Intel® Ethernet Controller I225-LM</td></tr></table>

# A.4.1 CPU Configuration

<table><tr><td>Feature</td><td>Option</td><td>Description</td></tr><tr><td>Hyper-threading</td><td>EnabledDisabled</td><td>Enable or Disable Hyper-Threading Technology</td></tr><tr><td>Active Performance-cores</td><td>All321</td><td>Number of P-cores to enable in each processor package. Note: Number of Cores and E-cores are looked at together. When both are {0,0}, Pcode will enable all cores.</td></tr><tr><td>Intel (VMX) Virtualization Technology</td><td>Enabled Disabled</td><td>When enabled, a VMM can utilize the additional hardware capabilities provided by Vanderpool Technology.</td></tr><tr><td>Intel(R) SpeedStep(TM)</td><td>Enabled Disabled</td><td>Allow more than two frequency ranges to be supported.</td></tr><tr><td>Intel(R) Speed Shift Technology</td><td>Enabled Disabled</td><td>Enable/Disable Intel(R) Speed Shift Technology Support. Enabling will expose the CPPC v2 interface to allow for hardware controlled P-states.</td></tr><tr><td>Turbo Mode</td><td>Enabled Disabled</td><td>Enable/Disable processor Turbo Mode (required EMTTM enabled too). AUTO means enabled.</td></tr><tr><td>C states</td><td>Disabled Enabled</td><td>Enable/Disable CPU Power Management. Allows CPU to go to C states when it's not 100% utilized.</td></tr><tr><td>TCC Activation Offset</td><td>0</td><td>Offset from factory set Tcc activation temperature at which the Thermal Control Circuit must be activated. Tcc will be activated at: Tcc activation Temp – Tcc Activation Offset. Tcc Activation Offset range is 0 to 63</td></tr></table>

# A.4.2 Power Management

<table><tr><td>Feature</td><td>Option</td><td>Description</td></tr><tr><td>Power Supply Unit</td><td>ATX ModeEmulate AT Mode</td><td>Select Emulation AT or ATX function. If this option set to [Emulation AT], BIOS will report no suspend functions (S3 &amp; S4) to ACPI OS. In windows XP, it will make OS show shutdown message during system shutdown. ATX: OS will turn off system power when shutdown.</td></tr><tr><td>State After G3</td><td>Last StatePower OffLast State</td><td>Specify what state to go to when power is re-applied after a power failure (G3 states).</td></tr><tr><td>RTC Wake system from S5</td><td>DisabledFixed TimeDynamic Time</td><td>Enable or disable System wake on alarm event. Select FixedTime, system will wake on the hr::min::sec specified. Select DynamicTime, system will wake on the current time + Increase minutes(S).</td></tr><tr><td>PCIe Wake</td><td>EnabledDisabled</td><td>Enable or disable PCI Express wake capability.</td></tr></table>

# A.4.3 Serial Console Redirection

<table><tr><td>Feature</td><td>Option</td><td>Description</td></tr><tr><td>Console Redirection</td><td>Disabled Enabled</td><td>Console Redirection Enable or Disable</td></tr><tr><td>Terminal Type</td><td>ANSIVT100VT100PlusVT-UTF9</td><td>Emulation: ANSI: Extended ASCII char set. VT100: ASCII char set. VT100Plus: Extends VT100 to support color, function keys, etc. VT-UTF8: Uses UTF8 encoding to map Unicode chars onto 1 or more bytes.</td></tr><tr><td>Bites per second</td><td>1152009600192003840057600</td><td>Selects serial port transmission speed. The speed must be matched on the other side. Long or noisy lines may require lower speeds.</td></tr><tr><td>Data Bits</td><td>87</td><td>Data Bites</td></tr><tr><td>Parity</td><td>NoneEvenOddMarkSpace</td><td>A parity bit can be sent with the data bits to detect some transmission errors. Even: parity bit is 0 if the num of 1's in the data bits is even. Odd: parity bit is 0 if num of 1's in the data bits is odd. Mark: parity bit is always 1. Space: Parity bit is always 0. Mark and Space Parity do not allow for error detection.</td></tr><tr><td>Stop Bits</td><td>12</td><td>Stop bits indicates the end of a serial data packet. (A stat bit indicates the beginning). The standard setting is 1 stop bit. Communication with slow devices may requires more than 1 stop bit.</td></tr><tr><td>Flow Control</td><td>NoneHardwareRTS/CTS</td><td>Flow control can prevent data loss from buffer overflow. When sending data, if the receiving buffers are full, a 'stop' signal can be sent to stop the data flow. Once the buffers are empty, a 'start' signal can be sent to re-start the flow. Hardware flow control uses tow wires to send start/stop signals.</td></tr><tr><td>VT-UTF8 Combo Key Support</td><td>EnabledEnabled</td><td>Enabled VT-UTF8 Combination Key Support for ANSI/VT100 terminals.</td></tr><tr><td>Recorder Mode</td><td>DisabledEnabled</td><td>With the mode enabled only text will be sent. This is to capture Terminal data.</td></tr><tr><td>Resolution 100x31</td><td>DisabledEnabled</td><td>Enables or disables extended terminal resolution.</td></tr><tr><td>Putty KeyPad</td><td>VT100LINUXXTERMR6SCOESCNVT400</td><td>Select FunctionKey and KeyPad on Putty.</td></tr></table>

# A.4.4 USB Configuration

<table><tr><td>Feature</td><td>Option</td><td>Description</td></tr><tr><td>USB Mass Storage Driver Support</td><td>EnabledDisabled</td><td>Enable/Disable USB Mass Storage Driver Support</td></tr><tr><td>USB transfer time-out</td><td>20 sec1 sec5 sec10 sec</td><td>The time-out value for Control, Bulk, and Interrupt transfers.</td></tr><tr><td>Device reset time-out</td><td>20 sec10 sec30 sec40 sec</td><td>USB mass storage device Start Unit command time-out.</td></tr><tr><td>Device power-up delay</td><td>AutoManual</td><td>Maximum time the device will take before it properly reports itself to the Host Controller. 'Auto' uses default value: for a Root port it is 100 ms, for a Hub port the delay is taken from Hub descriptor.</td></tr></table>

# A.4.5 TPM 2.0 Configuration

<table><tr><td>Feature</td><td>Option</td><td>Description</td></tr><tr><td>Security Device Support</td><td>EnableDisable</td><td>Enables or Disables BIOS support for security device. O.S. will not show Security Device. TCG EFI protocol and INT1A interface will not be available</td></tr><tr><td>SHA256 PCR Bank</td><td>EnabledDisabled</td><td>Enable or Disable SHA256 PCR Bank</td></tr><tr><td>SHA384 PCR Bank</td><td>DisabledEnabled</td><td>Enable or Disable SHA384 PCR Bank</td></tr><tr><td>Pending operation</td><td>NoneTPM Clear</td><td>Schedule an Operation for the Security Device. NOTE: Your computer will reboot during restart in order to change State of Security Device.</td></tr><tr><td>Platform Hierarchy</td><td>EnabledDisabled</td><td>Enable or Disable Platform Hierarchy</td></tr><tr><td>Storage Hierarchy</td><td>EnabledDisabled</td><td>Enable or Disable Storage Hierarchy</td></tr><tr><td>Endorsement Hierarchy</td><td>EnabledDisabled</td><td>Enable or Disable Endorsement Hierarchy</td></tr><tr><td>Physical Presence Spec Version</td><td>1.31.2</td><td>Select to Tell O.S. to support PPI Spec Version 1.2 or 1.3. Note some HCK tests might not support 1.3.</td></tr><tr><td>PH Randomization</td><td>EnabledDisabled</td><td>Enables or Disables Platform Hierarchy randomization. DO NOT ENABLE THIS QUESTION IN</td></tr></table>

# A.4.6 Onboard Device Configuration

<table><tr><td>Feature</td><td>Option</td><td>Description</td></tr><tr><td>COM1</td><td>EnabledDisabled</td><td>Enable or Disable Serial Port (COM)</td></tr><tr><td>COM1 Mode Control</td><td>RS232RS422RS485</td><td>Select COM1 mode. RS232, RS422, RS485</td></tr><tr><td>COM2</td><td>EnabledDisabled</td><td>Enable or Disable Serial Port (COM)</td></tr><tr><td>COM2 Mode Control</td><td>RS232RS422RS485</td><td>Select COM1 mode. RS232, RS422, RS485</td></tr><tr><td>COM3</td><td>EnabledDisabled</td><td>Enable or Disable Serial Port (COM)</td></tr><tr><td>COM4</td><td>EnabledDisabled</td><td>Enable or Disable Serial Port (COM)</td></tr><tr><td>Parallel Port</td><td>EnabledDisabled</td><td>Enable or Disable Parallel Port (LPT/LPTE)</td></tr><tr><td>Change Settings</td><td>AutoIO=378h; IRQ=5; IO=378h;IRQ=5,6,7,9,10,11,12; IO=278h;IRQ=5,6,7,9,10,11,12; IO=3BCh;IRQ=5,6,7,9,10,11,12;</td><td>Select an optimal settings for Super IO Device</td></tr><tr><td>Device Mode</td><td>STD Printer ModeSPP ModeEPP-1.9 and SPP ModeEPP-1.7 and SPP ModeECP ModeECP and EPP-1.9 ModeECP and EPP-1.7 Mode</td><td>Change the Printer Port Mode</td></tr><tr><td>LAN #1</td><td>EnabledDisabled</td><td>Enable/Disable</td></tr><tr><td>LAN #2</td><td>EnabledDisabled</td><td>Enable/Disable</td></tr></table>

# A.4.7 NCT6126H Hardware Monitor

<table><tr><td>Feature</td><td>Option</td><td>Description</td></tr><tr><td>CPU Fan Control Mode(Fan 1)</td><td>SMART FAN IV Manual mode</td><td>Configure Fan Control Mode. Select Manual Mode, user can configure a fix fan duty. Select SMART FAN IV, user can configure 4 temperatures and 4 fan duties. Select Auto Mode, FAN will run at automatic speed with thermal.</td></tr><tr><td>Temperature 1</td><td>25</td><td>The value of temperature1.</td></tr><tr><td>FD/PRM 1</td><td>140</td><td>The value of Fan Duty/RPM when temperature is T1.</td></tr><tr><td>Temperature 2</td><td>35</td><td>The value of temperature2.</td></tr><tr><td>FD/PRM 2</td><td>170</td><td>The value of Fan Duty/RPM when temperature is T2.</td></tr><tr><td>Temperature 3</td><td>45</td><td>The value of temperature3.</td></tr><tr><td>FD/PRM 3</td><td>200</td><td>The value of Fan Duty/RPM when temperature is T3.</td></tr><tr><td>Temperature 4</td><td>55</td><td>The value of temperature4.</td></tr><tr><td>FD/PRM 4</td><td>230</td><td>The value of Fan Duty/RPM when temperature is T4.</td></tr><tr><td>Critical Temperature</td><td>60</td><td>Fan temperature critical value.</td></tr><tr><td>CPU Fan Control Mode(Fan 2)</td><td>SMART FAN IV Manual mode</td><td>Configure Fan Control Mode. Select Manual Mode, user can configure a fix fan duty. Select SMART FAN IV, user can configure 4 temperatures and 4 fan duties. Select Auto Mode, FAN will run at automatic speed with thermal.</td></tr><tr><td>Temperature 1</td><td>25</td><td>The value of temperature1.</td></tr><tr><td>FD/PRM 1</td><td>140</td><td>The value of Fan Duty/RPM when temperature is T1.</td></tr><tr><td>Temperature 2</td><td>35</td><td>The value of temperature2.</td></tr><tr><td>FD/PRM 2</td><td>170</td><td>The value of Fan Duty/RPM when temperature is T2.</td></tr><tr><td>Temperature 3</td><td>45</td><td>The value of temperature3.</td></tr><tr><td>FD/PRM 3</td><td>200</td><td>The value of Fan Duty/RPM when temperature is T3.</td></tr><tr><td>Temperature 4</td><td>55</td><td>The value of temperature4.</td></tr><tr><td>FD/PRM 4</td><td>230</td><td>The value of Fan Duty/RPM when temperature is T4.</td></tr><tr><td>Critical Temperature</td><td>60</td><td>Fan temperature critical value.</td></tr></table>

# A.4.8 BIOS Watchdog Timer

<table><tr><td>Feature</td><td>Option</td><td>Description</td></tr><tr><td>BIOS POST Watchdog</td><td>DisabledSecond ModeMinute Mode</td><td>1. Disable: Disable WatchDog Timer;2. Second Mode: Enable Watchdog Timer in second mode; 3. Minute Mode: Enable Watchdog Timer in minute mode.</td></tr></table>

# A.4.9 PCI Express Configuration

<table><tr><td>Feature</td><td>Option</td><td>Description</td></tr><tr><td>▶ PEG Port Configuration</td><td></td><td>PEG Port Options</td></tr><tr><td>▶ PCI Express Root Port B0</td><td></td><td>PCI Express Root Port B0 Settings.</td></tr><tr><td>Pcie PII SCC</td><td>Auto0.0% - 2.0%Disable</td><td>Pcie PII SSC percentage. AUTO - Keep hw default, no BIOS override. Range is 0.0%-2.0%.PEG Port Options</td></tr><tr><td>Clock B0Assignment (REFCLK0)</td><td>EnabledPlatform-PORDisabled</td><td rowspan="4">Platform-POR = clock is assigned to PCIe port or LAN according to board layout. Enabled = keep clock enabled even if unused. Disabled = Disable clock.</td></tr><tr><td>Clock B0Assignment (REFCLK1)</td><td>EnabledPlatform-PORDisabled</td></tr><tr><td>Clock B0Assignment (REFCLK2)</td><td>EnabledPlatform-PORDisabled</td></tr><tr><td>Clock B0Assignment (REFCLK3)</td><td>EnabledPlatform-PORDisabled</td></tr></table>

# A.4.9.1 PEG Port Configuration

<table><tr><td>Feature</td><td>Option</td><td>Description</td></tr><tr><td>PCI Express Root Port 1</td><td>EnabledDisabled</td><td>Control the PCI Express Root Port</td></tr><tr><td>PCIe Speed</td><td>AutoGen1Gen2Gen3Gen4Gen5</td><td>Configure PCIe Speed</td></tr><tr><td>PEG1 Max Payload Size</td><td>256128</td><td>Select PEG Max Payload Size;Choose Auto(Default Device Capability) or force to 128/256 Bytes</td></tr><tr><td>PCI Express Root Port 2</td><td>EnabledDisabled</td><td>Control the PCI Express Root Port</td></tr><tr><td>PCIe Speed</td><td>AutoGen1Gen2Gen3Gen4Gen5</td><td>Configure PCIe Speed</td></tr><tr><td>PEG2 Max Payload Size</td><td>256128</td><td>Select PEG Max Payload Size;Choose Auto(Default Device Capability) or force to 128/256 Bytes</td></tr><tr><td>PCI Express Root Port 3</td><td>EnabledDisabled</td><td>Control the PCI Express Root Port</td></tr><tr><td>PCIe Speed</td><td>AutoGen1Gen2Gen3Gen4Gen5</td><td>Configure PCIe Speed</td></tr><tr><td>PEG3 Max Payload Size</td><td>256128</td><td>Select PEG Max Payload Size;Choose Auto(Default Device Capability) or force to 128/256 Bytes</td></tr></table>

# A.4.9.2 PCI Express Root Port B0

<table><tr><td>Feature</td><td>Option</td><td>Description</td></tr><tr><td>PCI Express Root Port B0</td><td>EnabledDisabled</td><td>Control the PCI Express Root Port</td></tr><tr><td>PCIe Speed</td><td>AutoGen1Gen2Gen3Gen4Gen5</td><td>Configure PCIe Speed</td></tr><tr><td>Detect Non-Compliance Device</td><td>DisabledEnabled</td><td>Detect Non-Compliance PCI Express Device. If enable, it will take more time at POST time.</td></tr><tr><td>Advanced Error Reporting</td><td>EnabledDisabled</td><td>Advanced Error Reporting Enable/Disable.</td></tr><tr><td>Max Payload</td><td>256128512</td><td>Max Payload settings</td></tr></table>

# A.4.10 Miscellaneous

<table><tr><td>Feature</td><td>Option</td><td>Description</td></tr><tr><td>Control Iommu Pre-boot Behavior</td><td>Disable IOMMUEnable IOMMU during boot</td><td>Enable IOMMU in Pre-boot environment (If DMAR table is installed in DXE and If VTD_INFFO_PPI is installed in PEI.)</td></tr><tr><td>DMA Control Guarantee</td><td>DisabledEnabled</td><td>Enable/Disable DMA_CONTROL_GUARANT EE bit</td></tr><tr><td>Above 4GB MMIO BIOS assignment</td><td>EnabledDisabled</td><td>Enable/Disable above 4GB MemoryMappedIO BIOS assignment. This is enabled automatically when Aperture Size is set to 2048MB.</td></tr></table>

# A.4.11 Network Stack Configuration

<table><tr><td>Feature</td><td>Option</td><td>Description</td></tr><tr><td>Network Stack</td><td>Disabled Enabled</td><td>Enable/Disable UEFI Network Stack</td></tr><tr><td>IPv4 PXE Support</td><td>Disabled Enabled</td><td>Enable/Disable IPv4 PXE boot support. If disabled, IPv4 PXE boot support will not be available.</td></tr><tr><td>IPv4 HTTP Support</td><td>Disabled Enabled</td><td>Enable/Disable IPv4 HTTP boot support. If disabled, IPv4 HTTP boot support will not be available.</td></tr><tr><td>IPv6 PXE Support</td><td>Disabled Enabled</td><td>Enable/Disable IPv6 PXE boot support. If disabled, IPv6 PXE boot support will not be available.</td></tr><tr><td>IPv6 HTTP Support</td><td>Disabled Enabled</td><td>Enable/Disable IPv6 HTTP boot support. If disabled, IPv6 HTTP boot support will not be available.</td></tr><tr><td>PXE boot wait time</td><td>0</td><td>Wait time in seconds to press ESC key to abort the PXE boot. Use either +/- or numeric keys to set the value.</td></tr><tr><td>Media detect count</td><td>1</td><td>Number of times the presence of media will be checked. Use either +/- or numeric keys to set the value.</td></tr></table>

# A.5 Chipset

<table><tr><td>Feature</td><td>Option</td><td>Description</td></tr><tr><td>► System (SA) Configuration</td><td></td><td>System Agent (SA) Parameters</td></tr><tr><td>► PCH-IO Configuration</td><td></td><td>PCH Parameters</td></tr><tr><td>PCH digital I/O device</td><td>Disabled Enabled</td><td>Disable/Enable ACPI GPIO Device support for PCH digital I/O and user LED</td></tr></table>

# A.5.1 System Agent (SA) Configuration

<table><tr><td>Feature</td><td>Option</td><td>Description</td></tr><tr><td>► Memory Configuration</td><td></td><td>Memory Configuration Parameters</td></tr><tr><td>► Graphics Configuration</td><td></td><td>Graphics Configuration</td></tr><tr><td>► VMD setup menu</td><td></td><td>VMD Configuration settings</td></tr><tr><td>► NVMe Configuration</td><td></td><td>NVMe Device Options Settings</td></tr><tr><td>NVMe Controller</td><td>Enabled Disabled</td><td>Control the PCI Express Root Port</td></tr><tr><td>VT-d</td><td>Enabled Disabled</td><td>VT-d capability</td></tr></table>

# A.5.1.1 Graphic Configuration

<table><tr><td>Feature</td><td>Option</td><td>Description</td></tr><tr><td>Primary Display</td><td>IGFXAutoPEG SlotPCH PCI</td><td>Select which of IGFX/PEG/PCI Graphics device should be Primary Display or select HG for Hybrid Gfx.</td></tr><tr><td>Internal Graphics</td><td>EnabledAutoDisabled</td><td>Keep IGFX enabled based on the setup options.</td></tr><tr><td>GTT Size</td><td>8MB2MB4MB</td><td>Select the GTT Size</td></tr><tr><td>Aperture Size</td><td>256MB128MB512MB1024MB2048MB</td><td>Select the Aperture SizeNote: Above 4GB MMIO BIOS assignment is automatically enabled when selecting &gt;2048MB aperture.To use this feature, please disable CSM Support.</td></tr><tr><td>DVMT Pre-Allocated</td><td>32M4M8M16M64M</td><td>Select DVMT 5.0 Pre-Allocated (Fixed) Graphics Memory size used by the Internal Graphics Device</td></tr></table>

# A.5.1.2 VMD Setup Menu

<table><tr><td>Feature</td><td>Option</td><td>Description</td></tr><tr><td>Enable VMD controller</td><td>Disabled Enabled</td><td>Enable/Disable to VMD controller</td></tr><tr><td>Enable VMD Global Mapping</td><td>Enabled Disabled</td><td>Enable/Disable to VMD Global Mapping</td></tr><tr><td>RAID0</td><td>Enabled Disabled</td><td>Enable/Disable RAID0 support</td></tr><tr><td>RAID1</td><td>Enabled Disabled</td><td>Enable/Disable RAID1 support</td></tr><tr><td>RAID5</td><td>Enabled Disabled</td><td>Enable/Disable RAID5 support</td></tr><tr><td>RAID10</td><td>Enabled Disabled</td><td>Enable/Disable RAID10 support</td></tr><tr><td>Intel Rapid Recovery Technology</td><td>Enabled Disabled</td><td>Enable/Disable Intel Rapid Recovery Technology.</td></tr><tr><td>RRT volumes can span internal and eSATA device</td><td>Enabled Disabled</td><td>Enable/Disable RRT volumes can span internal and eSATA drives</td></tr><tr><td>Intel(R) Optane(TM) Memory</td><td>Enabled Disabled</td><td>Enable/Disable System Acceleration with Intel(R) Optane(TM) Memory feature.</td></tr></table>

# A.5.2 PCH-IO Configuration

<table><tr><td>Feature</td><td>Option</td><td>Description</td></tr><tr><td>▶ SATA Configuration</td><td></td><td>SATA Device Options Settings</td></tr><tr><td>▶ USB Configuration</td><td></td><td>USB Configuration Settings</td></tr></table>

# A.5.2.1 SATA Configuration

<table><tr><td>Feature</td><td>Option</td><td>Description</td></tr><tr><td>SATA Mode Selection</td><td>AHCI</td><td>Determines how SATA controller(s) operate.</td></tr><tr><td>SATA Controller Speed</td><td>Gen3DefaultGen1Gen2</td><td>Indicates the maximum speed the SATA controller can support.</td></tr><tr><td>SATA HDD 0</td><td>EnabledDisabled</td><td rowspan="6">Enable or Disable SATA Port</td></tr><tr><td>SATA HDD 1</td><td>EnabledDisabled</td></tr><tr><td>SATA HDD 2</td><td>EnabledDisabled</td></tr><tr><td>SATA HDD 3</td><td>EnabledDisabled</td></tr><tr><td>SATA HDD 4</td><td>EnabledDisabled</td></tr><tr><td>SATA HDD 5</td><td>EnabledDisabled</td></tr></table>

# A.5.2.2 USB Configuration

<table><tr><td>Feature</td><td>Option</td><td>Description</td></tr><tr><td>USB Port Disable Override</td><td>Disable LinkSelect Per-Pin</td><td>Selectively Enable/Disable the corresponding USB port from reporting a Device Connection to the controller.</td></tr><tr><td>USB SS Physical Connector #0</td><td>EnabledDisabled</td><td rowspan="10">Enable/Disable this USB Physical Connector (physical port). Once disabled, any USB devices plug into the connector will not be detected by BIOS or OS.</td></tr><tr><td>USB SS Physical Connector #1</td><td>EnabledDisabled</td></tr><tr><td>USB SS Physical Connector #2</td><td>EnabledDisabled</td></tr><tr><td>USB SS Physical Connector #3</td><td>EnabledDisabled</td></tr><tr><td>USB SS Physical Connector #4</td><td>EnabledDisabled</td></tr><tr><td>USB SS Physical Connector #5</td><td>EnabledDisabled</td></tr><tr><td>USB SS Physical Connector #6</td><td>EnabledDisabled</td></tr><tr><td>USB SS Physical Connector #7</td><td>EnabledDisabled</td></tr><tr><td>USB SS Physical Connector #8</td><td>EnabledDisabled</td></tr><tr><td>USB SS Physical Connector #9</td><td>EnabledDisabled</td></tr><tr><td>USB HS Physical Connector #0</td><td>EnabledDisabled</td><td rowspan="10">Enable/Disable this USB Physical Connector (physical port). Once disabled, any USB devices plug into the connector will not be detected by BIOS or OS.</td></tr><tr><td>USB HS Physical Connector #1</td><td>EnabledDisabled</td></tr><tr><td>USB HS Physical Connector #2</td><td>EnabledDisabled</td></tr><tr><td>USB HS Physical Connector #3</td><td>EnabledDisabled</td></tr><tr><td>USB HS Physical Connector #4</td><td>EnabledDisabled</td></tr><tr><td>USB HS Physical Connector #5</td><td>EnabledDisabled</td></tr><tr><td>USB HS Physical Connector #6</td><td>EnabledDisabled</td></tr><tr><td>USB HS Physical Connector #7</td><td>EnabledDisabled</td></tr><tr><td>USB HS Physical Connector #8</td><td>EnabledDisabled</td></tr><tr><td>USB HS Physical Connector #9</td><td>EnabledDisabled</td></tr></table>

# A.6 Security

<table><tr><td>Feature</td><td>Option</td><td>Description</td></tr><tr><td>Administrator Password</td><td></td><td>Set Administrator Password</td></tr><tr><td>User Password</td><td></td><td>Set User Password</td></tr><tr><td>▶ Secure Boot menu</td><td></td><td>Secure Boot configuration</td></tr><tr><td>▶ Security Configuration</td><td></td><td>Security Configuration settings</td></tr></table>

# A.6.1 Secure Boot menu

<table><tr><td>Feature</td><td>Option</td><td>Description</td></tr><tr><td>Secure Boot Control</td><td>Disabled Enabled</td><td>Secure Boot feature is Active if Secure Boot is Enabled, Platform key (PK) is enrolled and the system is in User mode. The mode change requires platform reset.</td></tr><tr><td>Secure Boot Mode</td><td>Standard Custom</td><td>Secure Boot mode options: Standard or Custom.In Custom mode, Secure Boot Policy variables can be configured by a physically present user without full authentication</td></tr></table>

# A.6.2 Security Configuration

<table><tr><td>Feature</td><td>Option</td><td>Description</td></tr><tr><td>BIOS Lock</td><td>EnabledDisabled</td><td>Enable/Disable the PCH BIOS Lock Enable feature. Required to be enabled to ensure SMM protect of flash.</td></tr></table>

# A.7 Boot

<table><tr><td>Feature</td><td>Option</td><td>Description</td></tr><tr><td>Setup PromptTimeout</td><td>1</td><td>Number of seconds to wait for setup activation key. The maximum value is 8.</td></tr><tr><td>Bootup NumLock State</td><td>OffOn</td><td>Select the keyboard NumLock state</td></tr><tr><td>Quiet Boot</td><td>EnabledDisabled</td><td>Enables or disables Quiet Boot option</td></tr><tr><td>Fast Boot</td><td>Disable LinkEnabled</td><td>Enables or disables boot with initialization of a minimal set of devices required to launch active boot option. Has no effect for BBS boot options.</td></tr><tr><td>Boot Option #1</td><td>Hard DiskNVMEUEFI APCD/DVDSDUSB Hard DiskUSB CD/DVDUSB KeyUSB FloppyUSB LanNetworkDisabled</td><td>Sets the system boot order</td></tr><tr><td>Boot Option #2</td><td>NVMEHard DiskUEFI APCD/DVDSDUSB Hard DiskUSB CD/DVDUSB KeyUSB FloppyUSB LanNetworkDisabled</td><td>Sets the system boot order</td></tr><tr><td>Boot Option #3</td><td>UEFI APHard DiskNVMECD/DVDSDUSB Hard DiskUSB CD/DVDUSB KeyUSB FloppyUSB LanNetworkDisabled</td><td>Sets the system boot order</td></tr><tr><td>Boot Option #4</td><td>CD/DVDHard DiskNVMEUEFI APSDUSB Hard DiskUSB CD/DVDUSB KeyUSB FloppyUSB LanNetworkDisabled</td><td>Sets the system boot order</td></tr><tr><td>Boot Option #5</td><td>SDHard DiskNVMEUEFI APCD/DVDUSB Hard DiskUSB CD/DVDUSB KeyUSB FloppyUSB LanNetworkDisabled</td><td>Sets the system boot order</td></tr><tr><td>Boot Option #6</td><td>USB Hard DiskHard DiskNVMEUEFI APCD/DVDSDUSB CD/DVDUSB KeyUSB FloppyUSB LanNetworkDisabled</td><td>Sets the system boot order</td></tr><tr><td>Boot Option #7</td><td>USB CD/DVDHard DiskNVMEUEFI APCD/DVDSDUSB Hard DiskUSB KeyUSB FloppyUSB LanNetworkDisabled</td><td>Sets the system boot order</td></tr><tr><td>Boot Option #8</td><td>USB KeyHard DiskNVMEUEFI APCD/DVDSDUSB Hard DiskUSB CD/DVDUSB FloppyUSB LanNetworkDisabled</td><td>Sets the system boot order</td></tr><tr><td>Boot Option #9</td><td>USB FloppyHard DiskNVMEUEFI APCD/DVDSDUSB Hard DiskUSB CD/DVDUSB KeyUSB LanNetworkDisabled</td><td>Sets the system boot order</td></tr><tr><td>Boot Option #10</td><td>USB LanHard DiskNVMEUEFI APCD/DVDSDUSB Hard DiskUSB CD/DVDUSB KeyUSB FloppyNetworkDisabled</td><td>Sets the system boot order</td></tr><tr><td>Boot Option #11</td><td>NetworkHard DiskNVMEUEFI APCD/DVDSDUSB Hard DiskUSB CD/DVDUSB KeyUSB FloppyUSB LanDisabled</td><td>Sets the system boot order</td></tr></table>

# A.8 Save & Exit

<table><tr><td>Feature</td><td>Description</td></tr><tr><td>Save Changes and Exit</td><td>Exit system setup after saving the changes.</td></tr><tr><td>Discard Changes and Exit</td><td>Exit system setup without saving any changes.</td></tr><tr><td>Save Changes and Reset</td><td>Reset the system after saving the changes.</td></tr><tr><td>Discard Changes and Reset</td><td>Reset the system without saving any changes.</td></tr><tr><td>Save Changes</td><td>Save Changes done so far to any of the setup options.</td></tr><tr><td>Discard Changes</td><td>Discard Changes done so far to any of the setup options.</td></tr><tr><td>Restore Defaults</td><td>Restore/Load Default values for all the setup options.</td></tr><tr><td>Save as User Defaults</td><td>Save the changes done so far as User Defaults.</td></tr><tr><td>Restore User Defaults</td><td>Restore the User Defaults to all the setup options</td></tr><tr><td>Launch EFI Shell from file system device</td><td>Attempts to Launch EFI Shell application (Shell.efi) from one of the available file system devices</td></tr></table>

# A.9 MEBx

<table><tr><td>Feature</td><td>Option</td><td>Description</td></tr><tr><td>Intel(R) ME Password</td><td></td><td>MEBx Login</td></tr></table>

# Important Safety Instructions

For user safety, please read and follow all instructions, WARNINGS, CAUTIONS, and NOTES marked in this manual and on the associated equipment before handling/operating the equipment.

▶ Read these safety instructions carefully.
- Keep this user’s manual for future reference.
▶ Read the specifications section of this manual for detailed information on the operating environment of this equipment.
▶ When installing/mounting or uninstalling/removing equipment:

▷ Turn off power and unplug any power cords/cables.

▶ To avoid electrical shock and/or damage to equipment:

▷ Keep equipment away from water or liquid sources;
▷ Keep equipment away from high heat or high humidity;
▷ Keep equipment properly ventilated (do not block or cover ventilation openings);

▶ Make sure to use recommended voltage and power source settings;

▶ Always install and operate equipment near an easily accessible electrical socket-outlet;

▷ Secure the power cord (do not place any object on/over the power cord);

▶ Only install/attach and operate equipment on stable surfaces and/or recommended mountings; and,

▷ If the equipment will not be used for long periods of time, turn off and unplug the equipment from its power source.

▶ Never attempt to fix the equipment. Equipment should only be serviced by qualified personnel.

A Lithium-type battery may be provided for uninterrupted, backup or emergency power.

![The image displays a vertical rectangular sign with a black border and a white background. The upper portion features a red triangle with its apex pointing upward. Centered inside the red triangle is a black exclamation point. The lower portion of the sign contains the word 'WARNING' printed in black capital letters.](.nupro-e47-50m-41810-1000-10/08220b60ecb6f0faf8e7005dae84c5a4a08e1adbc5b544fb45fdce0873e263e6.jpg)

Risk of explosion if battery is replaced with one of an incorrect type. Dispose of used batteries appropriately.

▶ Equipment must be serviced by authorized technicians when:

The power cord or plug is damaged;
▷ Liquid has penetrated the equipment;
▷ It has been exposed to high humidity/moisture;
$\triangleright$ It is not functioning or does not function according to the user's manual;
It has been dropped and/or damaged; and/or it has an obvious sign of breakage.

![Yellow triangular warning sign with black smoke symbol indicating hazard or stress](.nupro-e47-50m-41810-1000-10/14ecf6eeba55718dd825e322dc6a331f350a2d7d3a9f78814a0d13fe66823723.jpg)

# WARNING

# Burn hazard.

Touching this surface could result in bodily injury. To reduce risk of injury allow the surface to cool before touching.

# Getting Service

Ask an Expert: https://www.adlinktech.com/en/Askanexpert

# ADLINK Technology, Inc.

No.66 Huaya 1st Road, Guishan District

Taoyuan City 333, Taiwan

Tel: +886-3-216-5088

Fax: +886-3-328-5706

Email: service@adlinktech.com

# Ampro ADLINK Technology, Inc.

5215 Hellyer Avenue, #110

San Jose, CA 95138, USA

Tel: +1-408-360-0200

Toll Free: +1-800-966-5200 (USA only)

Fax: +1-408-360-0222

Email: info@adlinktech.com

# ADLINK Technology (China) Co., Ltd.

300 Fang Chun Rd., Zhangjiang Hi-Tech Park

Pudong New Area, Shanghai, 201203 China

Tel: +86-21-5132-8988

Fax: +86-21-5132-3588

Email: market@adlinktech.com

# ADLINK Technology GmbH

Hans-Thoma-Strasse 11

D-68163 Mannheim, Germany

Tel: +49-621-43214-0

Fax: +49-621 43214-30

Email: emea@adlinktech.com

Please visit the Contact page at www.adlinktech.com for information on how to contact the ADLINK regional office nearest you.

# ADLINK Technology, Inc. (French Liaison Office)

Address: 6 allée de Londres, Immeuble Ceylan
91940 Les Ulis, France

Tel: +33 (0) 1 60 12 35 66

Fax: +33 (0) 1 60 12 35 66

Email: france@adlinktech.com

# ADLINK Technology Japan Corporation

Address: 〒101-0045 東京都千代田区神田鍛冶町 3-7-4
神田 374 ビル 4F
KANDA374 Bldg. 4F, 3-7-4 Kanda Kajicho,
Chiyoda-ku, Tokyo 101-0045, Japan

Tel: +81-3-4455-3722

Fax: +81-3-5209-6013

Email: japan@adlinktech.com

# ADLINK Technology, Inc. (Korean Liaison Office)

Address: 경기도 성남시 분당구 수내로 46 번길 4 경동빌딩 2 층 (수내동 4-4 번지) (우) 463-825

2F, Kyungdong B/D, 4 Sunae-ro 46 beon-gil

Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-825

Toll Free +82-80-800-0585

Tel +82-31-786-0585

Fax +82-31-786-0583

Email: korea@adlinktech.com

# ADLINK Technology Singapore Pte. Ltd.

Address: 84 Genting Lane #07-02A, Cityneon Design Centre Singapore 349584

Tel: +65-6844-2261

Fax: +65-6844-2263

Email: singapore@adlinktech.com

# ADLINK Technology Singapore Pte. Ltd. (Indian Liaison Office)

Address: #50-56, First Floor, Spearhead Towers Margosa Main Road (between 16th/17th Cross) Malleswaram, Bangalore - 560 055, India

Tel: +91-80-65605817, +91-80-42246107

Fax: +91-80-23464606

Email: india@adlinktech.com

# ADLINK Technology, Inc. (Israeli Liaison Office)

Address: 27 Maskit St., Corex Building
PO Box 12777
Herzliya 4673300, Israel

Tel: +972-54-632-5251

Fax: +972-77-208-0230

Email: israel@adlinktech.com

# ADLINK Technology, Inc. (UK Liaison Office)

Tel: +44 774 010 59 65

Email: UK@adlinktech.com
[🔗 Link to the original document](.nupro-e47-50m-41810-1000-10/nupro-e47-50m-41810-1000-10.pdf)