# PXI-3982

# PXI Embedded Controller

# User's Manual

![Exterior view of a network equipment unit (no visible text or symbols on the device body)](.pxi-3982-50-17058-1000-10/4e92e4fa8029f48c93cf8b1aa44a0e499c882f53bc526802d301c207e249e5f0.jpg)

Manual Rev.: 1.0

Revision Date: January 26, 2021

Part No: 50-17058-1000

Revision History

<table><tr><td>Revision</td><td>Release Date</td><td>Description of Change(s)</td></tr><tr><td>1.0</td><td>2021-01-26</td><td>Initial release</td></tr></table>

# Preface

# Copyright © 2021 ADLINK Technology Inc.

This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer.

# Disclaimer

The information in this document is subject to change without prior notice in order to improve reliability, design, and function and does not represent a commitment on the part of the manufacturer.

In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.

ADLINK is committed to fulfill its social responsibility to global environmental preservation through compliance with the European Union's Restriction of Hazardous Substances (RoHS) directive and Waste Electrical and Electronic Equipment (WEEE) directive. Environmental protection is a top priority for ADLINK. We have enforced measures to ensure that our products, manufacturing processes, components, and raw materials have as little impact on the environment as possible. When products are at their end of life, our customers are encouraged to dispose of them in accordance with the product disposal and/or recovery programs prescribed by their nation or company.

![Symbol of a trash bin crossed with two crossed lines, no text or labels present](.pxi-3982-50-17058-1000-10/020f5e61d2a9ef6b43759252d7cf5363b1e093632435761f35f9156b9ee2557d.jpg)

Battery Labels (for products with battery)
![Symbol of a trash bin crossed out by two diagonal lines (no text or numbers present)](.pxi-3982-50-17058-1000-10/73b17962935f6737c1f63ebf074886157469679ff5d6736e654c6b49c0045b39.jpg)

![Recycling symbol icon with three chasing arrows inside a square frame (no text or labels)](.pxi-3982-50-17058-1000-10/31155a81d02f642351aa27c02915481cabc6530f7b4c9463f70a5bc71c3c5bc5.jpg)

Li-ion

![RECYCLE\nRBRC\nLi-ion\n7.800.822.8837](.pxi-3982-50-17058-1000-10/69bb88fca637a9b51327250ba1e6621ba24a19aea0f2be78dc13b01a2781a4b0.jpg)

![Abstract geometric pattern with interlocking X and Y shapes (no text or symbols)](.pxi-3982-50-17058-1000-10/93baa7cccf604aadb9e939ae41a894ff9a15184fa2784d799362179f23b9c1e3.jpg)

廢電池請回收

# California Proposition 65 Warning

![The image displays a standard triangular warning sign featuring a yellow background with a thick black border. Inside the triangle, centered, is a large black exclamation mark.](.pxi-3982-50-17058-1000-10/820cbb3147eba90f4db8409d31879713c06b4a014f5c2099043311e5df8d1eb5.jpg)

WARNING: This product can expose you to chemicals including acrylamide, arsenic, benzene, cadmium, Tris(1,3-dichloro-2-propyl)phosphate (TDCPP), 1,4-Dioxane, formaldehyde, lead, DEHP, styrene, DINP, BBP, PVC, and vinyl materials, which are known to the State of California to cause cancer, and acrylamide, benzene, cadmium, lead, mercury, phthalates, toluene, DEHP, DIDP, DnHP, DBP, BBP, PVC, and vinyl materials, which are known to the State of California to cause birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

# Trademarks

Product names mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks of their respective companies.

# Conventions

Take note of the following conventions used throughout this manual to make sure that users perform certain tasks and instructions properly.

![The image displays a graphic icon of a white document with a folded top-left corner and faint horizontal lines. A large, bold red checkmark is superimposed over the center of the document.](.pxi-3982-50-17058-1000-10/8e81512c6ee241721a25a2b9d62abf25b56aae86c28fbeadbcbd1283de983887.jpg)
NOTE:

Additional information, aids, and tips that help users perform tasks.

![The image displays a standard caution sign: a yellow triangle with a black border containing a large black exclamation point in the center, set against a white background.](.pxi-3982-50-17058-1000-10/59bf6facf0bf2353a3682b4b59385245501449f8d302dd3cc1f4cd1578c23747.jpg)
CAUTION:

Information to prevent minor physical injury, component damage, data loss, and/or program corruption when trying to complete a task.

![A red triangular warning sign with a white border containing a white exclamation point in the center.](.pxi-3982-50-17058-1000-10/b8695f45b26534f62c386231b87aa8c905ffdd582bfdacb42d6b5e103e4cc3aa.jpg)
WARNING:

Information to prevent serious physical injury, component damage, data loss, and/or program corruption when trying to complete a specific task.

# Table of Contents

# Revision History...... ii

# Preface.... iii

# List of Figures ix

# List of Tables.... xi

# 1 Introduction ...... 1

1.1 Features.... 2
1.2 Specifications.... 3
1.3 I/O and Indicators 7

1.3.1 Front Panel 7
1.3.2 GPIB Connector 10
1.3.3 Reset Button.... 11
1.3.4 LED Indicators 11
1.3.5 USB 2.0 Ports....12
1.3.6 Gigabit Ethernet Ports 13
1.3.7 USB 3.0 Ports....14
1.3.8 Onboard Connections and Settings.... 15

# 2 Getting Started 17

2.1 Package Contents 17
2.2 Operating System Installation.... 18

2.2.1 Installation Environment 19
2.2.2 Installing the PXI-3982 20
2.2.3 Replacing the Hard Drive or Solid State Drive ..... 22
2.2.4 Clearing CMOS 24

# 3 Driver Installation.... 25

# A Appendix: PXI Trigger I/O Functions ......27

A.1 Data Types.... 27
A.2 Function Library 29

A.2.1 TRIG\_Init 29
A.2.2 TRIG\_Close 30
A.2.3 TRIG\_SetSoftTrg 31
A.2.4 TRIG\_Trigger\_Route 32
A.2.5 TRIG\_Trigger\_Clear 34
A.2.6 TRIG\_GetSoftTrg....35
A.2.7 TRIG\_Trigger\_Route\_Query 36
A.2.8 TRIG\_GetDriverRevision 38

# B Appendix: BIOS Setup....39

B.1 Entering the BIOS.... 39
B.2 Navigation 40
B.3 Menu Structure 41
B.4 Main 42

B.4.1 BIOS Information 42
B.4.2 Processor Information....42
B.4.3 PCH Information 43
B.4.4 System Management....43
B.4.5 System Date and Time 45

B.5 Advanced 46

B.5.1 CPU Configuration....46
B.5.2 Memory Configuration 48
B.5.3 Graphics Configuration 49
B.5.4 Onboard Devices Configuration....50
B.5.5 USB Configuration....51
B.5.6 Network Stack Configuration 52
B.5.7 TPM Configuration....52
B.5.8 Hardware Health Configuration 52

B.6 Security 53
B.6.1 Secure Boot Menu....53
B.7 Boot 55
B.7.1 CSM Configuration 56
B.8 Save & Exit 57

C Appendix: Dual BIOS 59
D Appendix: Legacy Boot Mode Settings....61

Important Safety Instructions.... 63

Getting Service.... 65

This page intentionally left blank.

# List of Figures

Figure 1-1: Functional Block Diagram....3
Figure 1-2: Front Panel 7
Figure 1-3: PXI Trigger SMB Jack 8
Figure 1-4: DisplayPort Connector....9
Figure 1-5: GPIB Connector....10
Figure 1-6: LED Indicators 11
Figure 1-7: Onboard Configuration 15

This page intentionally left blank.

# List of Tables

Table 1-1: Front Panel Legend 7
Table 1-2: DisplayPort Pin Assignment 9
Table 1-3: GPIB Pin Description....10
Table 1-4: LED Indicator Legend 11
Table 1-5: USB 2.0 Port Pin Assignment.... 12
Table 1-6: Ethernet Port Pin Assignments.... 13
Table 1-7: Ethernet Status LED Descriptions 13
Table 1-8: Onboard Configuration Legend 15
Table B-1: BIOS Hot Key Functions 40

This page intentionally left blank.

# 1 Introduction

The ADLINK PXI-3982 PXI $^{™}$ embedded controller, based on the Intel $^{®}$ Core $^{™}$ i7 processor, is specifically designed for PXI-based testing systems, providing a rugged and stable operating environment for a wide variety of testing and measurement applications.

Combining a state-of-the-art Intel® Core™ i7-6820EQ processor, and up to 32 GB of 2133 MHz DDR4 memory, the PXI-3982 utilizes four separate computing engines on a single processor, enabling execution of eight independent tasks simultaneously in a multitasking environment.

PXI-based testing systems typically make up a PXI platform and diversified standalone instruments for complex testing tasks. The PXI-3982 provides ample interface choices, including a DisplayPort connector, four USB 3.0 and two USB 2.0 ports for peripheral devices and USB instrument control, dual Gigabit Ethernet ports for LAN connections or controlling LXI instruments, an SMB connector for configurable input/output routing of signals to and from a PXI Trigger Bus on a PXI chassis, and a Micro-D GPIB connector for GPIB instrument connection.

![The image displays a white document icon with a folded top-left corner and faint horizontal gray lines, overlaid with a large red checkmark.](.pxi-3982-50-17058-1000-10/504094e2dea6bc798ca31b679347e2ff5c2ff346e6e83f27599ab503cbb5d8ca.jpg)
NOTE:

Memory addressing over 4 GB is OS-dependent, such that a 32-bit operating system may be unable to address memory space over 4GB. To fully utilize memory, 64-bit operating systems are required.

# 1.1 Features

- PXI™-1 PXI Hardware Specification Rev. 2.2 complaint
▶ 6th Generation Intel $^{®}$ Core $^{™}$ i7-6820EQ processor for maximum computing power, 3.5 GHz maximum in single-core, Turbo Boost mode
▶ Dual Channel DDR4 SO-DIMM
▷ Up to 32 GB 2133 MHz
▶ Maximum System Throughput 132 MB/s
▶ Preinstalled 256 GB or more SATA SSD
▶ Supports 2.5" HDD or SSD
▷ SATA 6.0 Gb/s
▶ Supports AHCI
▶ Integrated I/O
▶ Dual Gigabit Ethernet ports
▷ 4x USB 3.0 Ports
▷ 2x USB 2.0 Ports
▶ Built-in GPIB (IEEE488) controller
▷ 1x DisplayPort connector
▶ Trigger I/O for advanced PXI trigger functions
▶ OS
▷ Microsoft Windows 10 64-bit

# 1.2 Specifications

![**Labeled Blocks:**\n\n*   **Front Panel Connectors** (Container block)\n    *   DisplayPort Connector x1\n    *   GPIB Connector\n    *   GbE Connector\n    *   GbE Connector\n    *   USB2.0 Connector x2\n    *   USB3.0 Connector x4\n    *   SMB Connector\n*   **Mobile 6th Gen Intel® Core™ I7-6820EQ Processor**\n*   **DDR4 2133/2400 MHz SODIMM 1**\n*   **DDR4 2133/2400 MHz SODIMM 2**\n*   **PCI Express to PCI Switch**\n*   **Mobile Intel® QM170 Chipset**\n*   **GPIB Controller**\n*   **GbE Controller I219**\n*   **GbE Controller I210**\n*   **2.5' SATA Interposer Board**\n*   **Programmable MUX**\n*   **Rear Connector to PXI Chassis**\n\n**Connections:**\n\n*   **DisplayPort Connector x1** → **Mobile 6th Gen Intel® Core™ I7-6820EQ Processor** (Label: DP/HDMI Dual Mode)\n*   **Mobile 6th Gen Intel® Core™ I7-6820EQ Processor** ↔ **DDR4 2133/2400 MHz SODIMM 1** (Label: Memory Bus)\n*   **Mobile 6th Gen Intel® Core™ I7-6820EQ Processor** ↔ **DDR4 2133/2400 MHz SODIMM 2** (Label: Memory Bus)\n*   **Mobile 6th Gen Intel® Core™ I7-6820EQ Processor** ↔ **PCI Express to PCI Switch** (Label: PCIe Gen3 x16)\n*   **Mobile 6th Gen Intel® Core™ I7-6820EQ Processor** ↔ **Mobile Intel® QM170 Chipset** (Labels: Intel FDI, DMI 3.0)\n*   **GPIB Connector** → **GPIB Controller** (Label: GPIB)\n*   **GPIB Controller** → **Mobile Intel® QM170 Chipset** (Label: PCIe x1)\n*   **GbE Connector** → **GbE Controller I219** (Label: GbE I/F)\n*   **GbE Controller I219** → **Mobile Intel® QM170 Chipset** (Label: PCIe x1)\n*   **GbE Connector** → **GbE Controller I210** (Label: GbE I/F)\n*   **GbE Controller I210** → **Mobile Intel® QM170 Chipset** (Label: PCIe x1)\n*   **USB2.0 Connector x2** → **Mobile Intel® QM170 Chipset** (Label: USB 2.0)\n*   **USB3.0 Connector x4** → **Mobile Intel® QM170 Chipset** (Label: USB 3.0)\n*   **Mobile Intel® QM170 Chipset** → **2.5' SATA Interposer Board** (Label: SATA)\n*   **Mobile Intel® QM170 Chipset** ↔ **Programmable MUX** (Label: PCIe x1)\n*   **PCI Express to PCI Switch** ↔ **Rear Connector to PXI Chassis** (Label: PCI Bus)\n*   **SMB Connector** → **Programmable MUX** (Label: Trigger Signal)\n*   **Programmable MUX** → **Rear Connector to PXI Chassis** (Label: PXI Trigger Bus)](.pxi-3982-50-17058-1000-10/95a77da61d6ce885f7766fbada598cb097708b0ac9c19d3a7d11a1f30d151b78.jpg)

Figure 1-1: Functional Block Diagram

# Processor

Intel® Core™ i7-6820EQ 2.8 GHz processor
▶ DMI (Direct Media Interface) 3.0 with 8 GT/s bandwidth in each direction

# Chipset

Mobile Intel $^{®}$ QM170 chipset

# Memory

▶ Two standard 260-pin DDR4 SODIMM sockets
▶ Supports 2133 MHz DDR4 RAM up to 32 GB total
▶ Supports non-ECC, unbuffered memory

# Video

▶ DisplayPort resolution up to 3840 x 2160 @ 60 Hz
▶ DVI (with passive DisplayPort-to-DVI adapter) resolution up to 1920 x 1200 @ 60 Hz

![The image displays a document icon featuring a folded top-right corner and faint horizontal lines representing text, overlaid with a large red checkmark.](.pxi-3982-50-17058-1000-10/3d0320112eb1c55e63d39d9035af586771b86de9a003aece62bb2a7b42dbfc2a.jpg)
NOTE:

DisplayPort adapters for other standards are available, with maximum available resolution dependent on the adapter

# Storage

Built-in 2.5" 256 GB or more SATA solid state hard drive.

# Ethernet Connectivity

Dual Gigabit Ethernet controllers through two RJ-45 connectors with speed/link/active LED on the faceplate, with both supporting Wake on LAN.

# USB

Two USB 2.0 and four USB 3.0 ports on the faceplate.

# GPIB

Onboard IEEE488 GPIB controller through Micro-D 25-pin connector on the faceplate.

# Trigger I/O

One SMB connector on the faceplate to route an external trigger signal to/from PXI trigger bus.

# Dimensions (3U PXI module)

3U/3-slot PXI standard

# Expansion Slots

System slot (5V VIO PCI bus) and 2 controller expansion slots on chassis/backplane. 32-bit and 5V VIO PCI bus of system slot.

# Weight

0.91 kg (exclusive of packaging)

![The image displays a red triangular warning sign with a thick white border. Centered inside the red triangle is a large white exclamation mark.](.pxi-3982-50-17058-1000-10/3b17b9265e32c462fb6278407e089c42f436e324ec2a807742176922d084860a.jpg)

WARNING:

Do not remove the blue key from the PXI-3982 system connector, only the 5V VIO PCI bus is compatible; the 3.3V VIO PCI bus is not. SEVERE system damage may result.

Environmental

<table><tr><td>Condition</td><td>Range</td></tr><tr><td>Operating temperature with SSD</td><td>0 to 55°C</td></tr><tr><td>Operating temperature with HDD</td><td>0 to 50°C</td></tr><tr><td>Storage temperature</td><td>-20 to 70°C</td></tr><tr><td>Relative humidity, non-condensing</td><td>5 to 95%</td></tr></table>

# Shock and Vibration

Functional shock 30 G, half-sine, 11 ms pulse duration

Random vibration:

▶ Operating: 5 to 500 Hz, 0.21 Grms, 3 axes
▶ Non-operating: 5 to 500 Hz, 2.46 Grms, 3 axes

![The image displays a simple icon of a white document with a folded top-left corner. Faint gray horizontal lines run across the paper, suggesting text. A large, bold red checkmark is superimposed over the left side of the document. There is no actual text to transcribe.](.pxi-3982-50-17058-1000-10/94c4fbbfce266afb71ac6f725ec3e62bb36791f2814ff810930d741edfc1c8ee.jpg)

NOTE:

Environmental, shock, and vibration values are only valid with use of an ADLINK-provided SSD.

# Certifications

Electromagnetic compatibility:

▶ EN 61326-1 (IEC 61326-1): Class A emissions; Basic immunity
▶ EN 55011 (CISPR 11): Group 1, Class A emissions
EN 55032 2015/AC: 2016 Class A
▶ EN 55032 2015/AC: 2016 Class A
▶ EN 55024 2010+ A1: 2015
▶ EN 61000-3-2:2014: Class A
EN 61000-3-3:2013: Class A
EN 55024:2010+A1:2015: Immunity
▶ FCC 47 CFR Part 15 Subpart A (Class A)
▶ ICES-001 Class A
▶ ICES-003 Issue 6-2016
▶ AS/NZS CISPR 11: Group 1, Class A emissions
AS/NZS CISPR 32: 2015 (Ed 2.0)/C1:2016: Class A

The PXI-3982 meets the essential requirements of applicable European Directives.

Power Requirements

<table><tr><td>Typical Consumption</td><td>DC +3.3V</td><td>DC +5V</td><td>DC +12V</td></tr><tr><td>Typical operation(Measured while W10 is idle)</td><td>5A</td><td>2.5A</td><td>2A</td></tr><tr><td>Heavy operation(Measured while W10 is under heavy CPU and storage utilization)</td><td>5A</td><td>2.8A</td><td>8A</td></tr></table>

# 1.3 I/O and Indicators

# 1.3.1 Front Panel

![ADLINK\nTECHNOLOGY INC.\nPXI-3982\nPXI Embedded\nController\nHD HS\nPW\nA\nG\nTRIG\nB\nF\nC\nD\nE\nGPIOB](.pxi-3982-50-17058-1000-10/53c3834a989c1b2f5d58d2e9267f8cb2ca85a52b23a97e0fa10c32201fe518ba.jpg)

Figure 1-2: Front Panel

<table><tr><td>A</td><td>Reset Button</td><td>E</td><td>GPIB Connector (Micro D-Sub 25P)</td></tr><tr><td>B</td><td>DisplayPort</td><td>F</td><td>2x Gigabit Ethernet</td></tr><tr><td>C</td><td>4x USB 3.0</td><td>G</td><td>PXI Trigger Connector (SMB jack)</td></tr><tr><td>D</td><td>2x Type-A USB 2.0</td><td>H</td><td>LED Indicators</td></tr></table>

Table 1-1: Front Panel Legend

# PXI Trigger Connector

![Ground\nTrigger](.pxi-3982-50-17058-1000-10/e2424c0413a9e398a0a3428cb923544e771468de4e65db07b5dedb2f39a50a29.jpg)

Figure 1-3: PXI Trigger SMB Jack

The PXI trigger connector is an SMB jack, used to route external trigger signals to or from the PXI backplane. Trigger signals are TTL-compatible and edge sensitive. The PXI-3982 provides four trigger routing modes from/to the PXI trigger connector to synchronize PXI modules, including

▶ From a selected trigger bus line to PXI trigger connector
▶ From the PXI trigger connector to a selected trigger bus line
▶ From software trigger to a selected trigger bus line
▶ From software trigger to PXI trigger connector

All trigger modes are programmable by the provided driver.

# DisplayPort Connectors

Provide monitor connection with installation of requisite adapters required if connecting to VGA/DVI/HDMI monitors. Dual display function is also supported.

![19\n1\n20\n2](.pxi-3982-50-17058-1000-10/077e269b54c4318f474c9ce46c2a6001ede7342910865f3ee8d55bddc6e2c5f2.jpg)

Figure 1-4: DisplayPort Connector

<table><tr><td>Pin</td><td>Signal</td><td>Pin</td><td>Signal</td></tr><tr><td>1</td><td>CN_DDPx0+</td><td>11</td><td>GND</td></tr><tr><td>2</td><td>GND</td><td>12</td><td>CN_DDPx3-</td></tr><tr><td>3</td><td>CN_DDPx0-</td><td>13</td><td>CN_DDPx_AUX_SEL</td></tr><tr><td>4</td><td>CN_DDPx1+</td><td>14</td><td>CN_DDPx_CONFIG2</td></tr><tr><td>5</td><td>GND</td><td>15</td><td>CN_DDPx_AUX+</td></tr><tr><td>6</td><td>CN_DDPx1-</td><td>16</td><td>GND</td></tr><tr><td>7</td><td>CN_DDPx2+</td><td>17</td><td>CN_DDPx_AUX-</td></tr><tr><td>8</td><td>GND</td><td>18</td><td>CN_DDPx_HPD</td></tr><tr><td>9</td><td>CN_DDPx2-</td><td>19</td><td>GND</td></tr><tr><td>10</td><td>CN_DDPx3+</td><td>20</td><td>+V3.3_DDPx_PWR</td></tr></table>

Table 1-2: DisplayPort Pin Assignment

# 1.3.2 GPIB Connector

The GPIB connector is a micro D-sub 25P connector, controlling external bench-top instruments. Connection to other instruments requires the optional ACL-IEEE488-MD1-A cable. The onboard GPIB controller provides:

▶ Full compatibility with IEEE 488 standard
▶ Up to 1.5 MB/s data transfer rates
▶ Onboard 2 KB FIFO for read/write operations
▶ Driver APIs are compatible with NI-488.2 driver software
▶ Connection with up to 14 instruments

![1\n13\n14\n25](.pxi-3982-50-17058-1000-10/fe26bb9dbc02ba0ec7bcc730598188875aa0007b5a1b6a72408a261caba1c737.jpg)

Figure 1-5: GPIB Connector

<table><tr><td>Pin</td><td>Signal</td><td>Description</td><td>Pin</td><td>Signal</td><td>Description</td></tr><tr><td>1</td><td>DIO1#</td><td>GPIB Data 1</td><td>14</td><td>DIO5#</td><td>GPIB Data 5</td></tr><tr><td>2</td><td>DIO2#</td><td>GPIB Data 2</td><td>15</td><td>DIO6#</td><td>GPIB Data 6</td></tr><tr><td>3</td><td>DIO3#</td><td>GPIB Data 3</td><td>16</td><td>DIO7#</td><td>GPIB Data 7</td></tr><tr><td>4</td><td>DIO4#</td><td>GPIB Data 4</td><td>17</td><td>DIO8#</td><td>GPIB Data 8</td></tr><tr><td>5</td><td>EOI</td><td>End Or Identify</td><td>18</td><td>REN</td><td>Remote Enable</td></tr><tr><td>6</td><td>DAV</td><td>Data Valid</td><td>19</td><td>Ground</td><td>Signal Ground</td></tr><tr><td>7</td><td>NRFD</td><td>Not Ready For Data</td><td>20</td><td>Ground</td><td>Signal Ground</td></tr><tr><td>8</td><td>NDAC</td><td>No Data Accepted</td><td>21</td><td>Ground</td><td>Signal Ground</td></tr><tr><td>9</td><td>IFC</td><td>Interface Clear</td><td>22</td><td>Ground</td><td>Signal Ground</td></tr><tr><td>10</td><td>SRQ</td><td>Service Request</td><td>23</td><td>Ground</td><td>Signal Ground</td></tr><tr><td>11</td><td>ATN</td><td>Attention</td><td>24</td><td>Ground</td><td>Signal Ground</td></tr><tr><td>12</td><td>Chassis Ground</td><td>Chassis Ground</td><td>25</td><td>Ground</td><td>Signal Ground</td></tr><tr><td>13</td><td>Ground</td><td>Signal Ground</td><td></td><td></td><td></td></tr></table>

Table 1-3: GPIB Pin Description

# 1.3.3 Reset Button

The reset button, activated by insertion of any pin-like implement, executes a hard reset for the PXI-3982.

# 1.3.4 LED Indicators

Three LED indicators on the faceplate indicate operational status of the PXI-3982, as follows.

![HD HS\nPW](.pxi-3982-50-17058-1000-10/1a54f45fd2655c11fef1f819a8f26e9318150c151e5040f1b088845c514d1962.jpg)

Figure 1-6: LED Indicators

<table><tr><td>LED</td><td>Color</td><td>Description</td></tr><tr><td>PW</td><td>Green</td><td>Indicates system power, remaining lit when the system boots normally and main power supply is functioning.</td></tr><tr><td>HD</td><td>Yellow</td><td>Indicates operating state of the HDD or SSD, flashing during access to or activity on the SATA HDD.</td></tr><tr><td>HS</td><td>Blue</td><td>Indicates system status, blinking on and off once during boot when system status is good, and continuously blinking or remaining lit when the system malfunctions.</td></tr></table>

Table 1-4: LED Indicator Legend

# 1.3.5 USB 2.0 Ports

The PXI-3982 provides two USB 2.0 ports via USB Type-A connectors on the faceplate, all compatible with hi-speed, full-speed and low-speed USB devices. Supported boot devices include USB flash drive, USB floppy, USB CD-ROM, and others, with boot priority and device settings configured in BIOS. See section B.7: "Boot" on page 55 for more information.

![Pure electrical connector pinout diagram without any text or symbols](.pxi-3982-50-17058-1000-10/ad01ca32cdab4263d3d23bf9fa47529ce153040926cd7f1c0a770cf2d6a9e932.jpg)

![1\n2\n3\n4](.pxi-3982-50-17058-1000-10/09aaf2e2b607ea55647a9774c554030ed9d526a4e8c59ca1ecd2a74d730b526f.jpg)

<table><tr><td>Pin</td><td>Signal</td></tr><tr><td>1/5</td><td>Power 5V</td></tr><tr><td>2/6</td><td>USB Data-</td></tr><tr><td>3/7</td><td>USB Data +</td></tr><tr><td>4/8</td><td>Ground</td></tr></table>

Table 1-5: USB 2.0 Port Pin Assignment

# 1.3.6 Gigabit Ethernet Ports

Dual Gigabit Ethernet connection is provided on the PXI-3982 front panel.

<table><tr><td>Pin</td><td>1000Base-T Signal</td><td>100/10Base-T Signal</td></tr><tr><td>1</td><td>MDI0+</td><td>TX+</td></tr><tr><td>2</td><td>MDI0-</td><td>TX-</td></tr><tr><td>3</td><td>MDI1+</td><td>RX+</td></tr><tr><td>4</td><td>MDI2+</td><td>Reserved</td></tr><tr><td>5</td><td>MDI2-</td><td>Reserved</td></tr><tr><td>6</td><td>MDI1-</td><td>RX-</td></tr><tr><td>7</td><td>MDI3+</td><td>Reserved</td></tr><tr><td>8</td><td>MDI3-</td><td>Reserved</td></tr></table>

Table 1-6: Ethernet Port Pin Assignments

Each Ethernet port includes two LED indicators, one Active/Link indicator and one Speed indicator, functioning as follows.

<table><tr><td></td><td>LED</td><td>Status</td><td>Description</td></tr><tr><td rowspan="6">&lt;img src="images/1a70e868dd9ca54f497195118c07f80ab0431365ff1879a659fbdcc9a4bf1b5c.jpg"/&gt;</td><td rowspan="3">Speed(Green/Orange)</td><td>Off</td><td>10 Mbps</td></tr><tr><td>Green</td><td>100 Mbps</td></tr><tr><td>Orange</td><td>1000 Mbps</td></tr><tr><td rowspan="3">Active/Link(Orange)</td><td>Off</td><td>Ethernet port is disconnected</td></tr><tr><td>On</td><td>Ethernet port is connected with no data transmission</td></tr><tr><td>Flashing</td><td>Ethernet port is connected with data transmitted/received</td></tr></table>

Table 1-7: Ethernet Status LED Descriptions

# 1.3.7 USB 3.0 Ports

The PXI-3982 provides four Type-A USB 3.0 ports on the front panel, supporting SuperSpeed, Hi-Speed, full-speed, and low-speed downstream transmission. Multiple boot devices, including USB flash, USB external HD, and USB CD-ROM drives are supported, with boot priority configured in BIOS.

![The image depicts a white icon of a piece of paper with a folded top-left corner. Faint gray horizontal lines are drawn across the paper. A large red checkmark is superimposed diagonally over the center of the document.](.pxi-3982-50-17058-1000-10/3d77b2e3044e785820d651e368981a57e22db93a808210c2a579043251aaa252.jpg)
NOTE:

USB 3.0 may not be supported by the OS installation programs/environment. Use USB 2.0 ports for OS installation if necessary.

# 1.3.8 Onboard Connections and Settings

![ADLINK\nTECHNOLOGY INC.\n2.5' SATA SSD\n3TG6-P\nSeries\ninnodisk\nA\nB\nH15\nSW1\nSW2\nR271\nR280\nR286\nR285\nR283\nR279\nR274\nR270\nR269\nR268\nR267\nR266\nR265\nR264\nR263\nR262\nR261\nR260\nR259\nR258\nR257\nR256\nR255\nR254\nR253\nR252\nR251\nR250\nR249\nR248\nR247\nR246\nR245\nR244\nR243\nR242\nR241\nR240\nR239\nR238\nR237\nR236\nR235\nR234\nR233\nR232\nR231\nR230\nR229\nR228\nR227\nR226\nR225\nR224\nR223\nR222\nR221\nR220\nR219\nR218\nR217\nR216\nR215\nRNQ18\nCN13\nCN15](.pxi-3982-50-17058-1000-10/a1b1931a9ed7293bce7af1d35d8537acf3edbc724cec8bf0b20d2fd86ea18d9d.jpg)

Figure 1-7: Onboard Configuration

<table><tr><td>A</td><td>SW1 Clear CMOS switch</td></tr><tr><td>B</td><td>SATA connector</td></tr></table>

Table 1-8: Onboard Configuration Legend

This page intentionally left blank.

# 2 Getting Started

This chapter describes procedures for installing the PXI-3982 and making preparations for its operation, including hardware and software setup. Note that the PXI controller is shipped with RAM and an HDD or SSD preinstalled. Contact ADLINK or an authorized dealer if there are any problems during the installation.

![The image displays a graphic icon of a white document with a folded top-right corner and faint horizontal lines, overlaid with a large, bold red checkmark.](.pxi-3982-50-17058-1000-10/04094a5d657d0cddebbee694f7c70cc48b88a18099935aba5327b1ead4a3af8b.jpg)
NOTE:

Diagrams and illustrated equipment are for reference only. Actual system configuration and specifications may vary.

# 2.1 Package Contents

Before beginning, check the package contents for any damage and ensure that the following items are included:

▶ PXI-3982 Controller (equipped with RAM and HDD or SSD)
▶ PXI-3982 Quick Start Guide
▶ DisplayPort to DVI cable

If any of these items are missing or damaged, contact the dealer from whom you purchased the product. Save the shipping materials and carton in case you want to ship or store the product in the future.

![The image displays a central red triangle pointing upward containing a white exclamation mark. This symbol is flanked on the left and right sides by vertical black bars.](.pxi-3982-50-17058-1000-10/3557aded346ff4968dd81e3d10aa74a6507a19acac5a66d242654d5abcf40e4f.jpg)
WARNING:

Do not install or apply power to equipment that is damaged or missing components. Retain the shipping carton and packing materials for inspection. Contact an ADLINK dealer/vendor immediately for assistance and obtain authorization before returning any product.

# 2.2 Operating System Installation

For more detailed information about the operating system, refer to the documentation provided by the operating system manufacturer. Preferred/supported operating systems for the PXI controller are:

▶ Windows 10 64-bit
▶ For other OS support, contact ADLINK

Most operating systems require initial installation from a hard drive, floppy drive, or CD-ROM drive. The PXI controller supports USB CD-ROM drive, USB flash disk, USB external hard drive, or a USB floppy drive as the first boot device. See section B.7: "Boot" on page 55 for information about setting the boot devices. These devices should be configured, installed, and tested with the supplied drivers before attempting to load the new operating system.

![The image displays a graphic icon of a white document sheet featuring faint horizontal lines and a folded top-right corner. A large, bold red checkmark is drawn diagonally across the center of the paper.](.pxi-3982-50-17058-1000-10/6d4ce1a7a5aab3f6bd762c22fd9e6b7b5febc1fcd86bbca92949914158668808.jpg)
NOTE:

Read the release notes and installation documentation provided by the operating system vendor. Be sure to read all the README files or documents provided on the distribution disks, as these typically note documentation discrepancies or compatibility problems.

1. Select the appropriate boot device order from the BIOS Boot Setup Menu based on the OS installation media used. For example, if the OS is distributed on a bootable installation CD, select USB CD-ROM as the first boot device and reboot the system with the installation CD in the USB CD-ROM drive.
2. Proceed with the OS installation as directed and be sure to select appropriate device types if prompted. Refer to the appropriate hardware manuals for specific device types and compatibility modes of ADLINK PXI products.
3. When installation is complete, reboot the system and set the boot device order in the BIOS Boot Setup Menu accordingly.

# 2.2.1 Installation Environment

When preparing to install any equipment described in this manual, first refer to Important Safety Instructions.

Only install equipment in well lit areas on flat, sturdy surfaces with access to basic tools such as flat- and cross-head screw-drivers, preferably with magnetic heads as screws and stand-offs are small and easily misplaced.

Recommended Installation Tools include:

▶ Phillips (cross-head) screwdriver
▶ Flat-head screwdriver
Anti-static wrist strap
Anti-static mat

ADLINK PXI system controllers are electrostatically sensitive and can be easily damaged by static electricity. The equipment must be handled on a grounded anti-static mat, and operators must wear an anti-static wristband, grounded at the same point as the anti-static mat.

Inspect the carton and packaging for damage. Shipping and handling may cause damage to the contents. Ensure that all contents are undamaged before installing.

![The image displays a standard warning sign. It features a yellow triangle with a black border containing a large black exclamation point. Below the triangle, the text 'CAUTION:' is printed in black capital letters.](.pxi-3982-50-17058-1000-10/3f0f5cb8ba6326f78d38c58456b2d3e2c745dc4a8776b6d2ebfcff055bf23aac.jpg)

All equipment must be protected from static discharge and physical shock. Never remove any of the socketed parts except at a static-free workstation. Use the anti-static bag shipped with the product to handle the equipment and wear a grounded wrist strap when servicing or installing.

# 2.2.2 Installing the PXI-3982

1. Release the red locking lever.

![Close-up of a black mechanical component with red and black parts, showing a red arrow pointing to a specific area (no text or symbols visible)](.pxi-3982-50-17058-1000-10/6e06c9cc3e80adf17ae5ea8af5658a18768c3f64c674957d7f33b0cc1d373a2a.jpg)

2. Depress the latch.

![Close-up of a mechanical device with a red arrow pointing to a red component, no visible text or symbols.](.pxi-3982-50-17058-1000-10/f9d5f47171b23192d504617bc58cb1b551fdc21c5f345335f37a113ef93c70bd.jpg)

3. Locate the system controller slot of the chassis (Slot 1).

4. Align the controller's top and bottom edges with the card guides, and carefully slide the PXI-3982 into the chassis, as shown.

![ADLINK\nPXIS-2719A\n19-Slot Smart PXI Chassis\nPXI-3982\nPXI Embedded\nController\nTRIG\nADLINK\nTECHNOLOGY INC.\nINNODISK\n2.5' SATA SSD\n3TG6-P\nSeries](.pxi-3982-50-17058-1000-10/359f1c3fbd99742ce0bbe4ee64135d240cc4e03ea1b53342450d2d2e13d0ebca.jpg)

5. Elevate the latch until the PXI-3982 is fully seated in the chassis backplane. The alignment pin on the rear of the latch can be threaded into the best fit alignment port in the chassis rail.

6. Fasten the four mounting screws on the faceplate and connect all peripheral devices.

# 2.2.3 Replacing the Hard Drive or Solid State Drive

The PXI controller provides a SATA 3.0 port with a pre-installed 2.5" SATA hard drive or solid state drive. Replacing the HDD or SSD is accomplished as follows.

1. Locate the five screws attaching the hard drive housing to the PXI controller, as shown.

![innodisk\n2.5' SATA SSD\n3TG6-P\nSeries\nADLINK\nTECHNOLOGY INC.](.pxi-3982-50-17058-1000-10/b37daac82dc67a2d19aa879d2e0eacbe0a0a8c2b15dcdbabbcffc31a01a5fe9a.jpg)

2. Remove the screws.
3. Gently lift and remove the housing with the installed HDD or SSD.

4. Locate the four screws (two on each side, as shown) fixing the hard drive, and remove them.

![0025-T5S-AE\nSF D6Y17EJ\nE49 E48 E47 E46 E45 E44 E43 E42 E41 E40 E39 E38 E37 E36 E35 E34 E33 E32 E31 E30 E29 E28 E27 E26 E25 E24 E23 E22 E21 E20 E19 E18 E17 E16 E15 E14 E13 E12 E11 E10 E9 E8 E7 E6 E5 E4 E3 E2 E1 E0 E0\nE40 E39 E38 E37 E36 E35 E34 E33 E32 E31 E30 E29 E28 E27 E26 E25 E24 E23 E22 E21 E20 E19 E18 E17 E16 E15 E14 E13 E12 E11 E10 E9\nE41 E40 E39 E38 E37 E36 E35 E34 E33 E32 E31 E30\nE42 E41 E40 E39 E38 E37 E36\nE43 E42 E41 E40 E39 E38\nE44 E43 E42 E41 E40 E39\nE45 E44 E43 E42 E41 E40\nE46 E45 E44 E43 E42 E41\nE47 E46 E45 E44 E43 E42\nE48 E47 E46 E45 E44 E43\nE49 E48 E47 E46\nE50 E49 A-001\nG507VMX20077 OP\nC:CL\nCI\n2060-800025-001 REV P2\nTP 022 000 C\nOVP\nTV9\nTV10\nE56\nE16\nE17\nE26\nE27\nE30\nE33\nE65\nE85\nE86\nE87\nE88\nE89\nE90\nE91\nE92\nE93\nE94\nE95\nE96\nE97\nE98\nE99\nE10\nE11\nE12\nE13\nE14\nE15\nE16\nE17\nE18\nE19\nE20\nE21\nE22\nE23\nE24\nE25\nE26\nE27\nE28\nE29\nE30](.pxi-3982-50-17058-1000-10/ed73f0dd2588fe015e5948df4a978d85a6ebcc3e8361c81f193e602ff5d8ee20.jpg)

5. To install an HDD, SSD, or other compatible SATA hard drive, reverse the steps and reinstall the PXI controller into the PXI system.

# 2.2.4 Clearing CMOS

In the event of a system malfunction causing the PXI controller to halt or fail to boot, clear the CMOS and restore the controller BIOS to its default settings. To clear the CMOS:

1. Shut down the controller operating system and turn off the PXI Chassis.
2. Remove the PXI controller from the chassis. Observe all anti-static precautions.
3. Locate the CMOS clear switch (SW1) on the board (see section 1.3.8: "Onboard Connections and Settings" on page 15). Move the switch from the Normal position...

![The image displays a close-up of a digital interface element against a dark gray background. It features a horizontal rectangular bar where the majority of the bar is a medium gray color. Attached to the far right end of this gray section is a white rectangular block. Below the left end of the medium gray section, there is a small, solitary white dot.](.pxi-3982-50-17058-1000-10/5985838699c7771422725e101fcdb09d62a9f7f507520498e8a57c159297efce.jpg)

...to the Clear position.

![A dark grey horizontal bar containing a white square and a small white dot below it on the left, resembling a magnifying glass icon, and a large dark grey rectangle to the right.](.pxi-3982-50-17058-1000-10/310be449fd242495fd735250ad8db898ae381587cd9d97759cdbd7d9bcd41d4e.jpg)

Wait five seconds, then return the switch to the Normal position.

![The image displays a close-up of a digital interface element, resembling a progress bar. It features a long, dark gray horizontal rectangle that extends almost to the right edge, followed by a white square at the far right. Below the left edge of the gray bar is a small white dot. There is no text.](.pxi-3982-50-17058-1000-10/cd95d04ca512b9a1b272cb07eb8f0c8884e85e67215ea1bda7fcd90901454bb8.jpg)

4. Remount the controller into the PXI chassis.
5. Press &lt;Delete&gt; or &lt;ESC&gt; to enter BIOS Setup when the splash logo appears.
6. Press &lt;F9&gt; to load optimized defaults in BIOS Setup.
7. Modify the system date and time.
8. Press &lt;F10&gt; to save configuration and exit.

# 3 Driver Installation

Download the Windows 10 drivers for your system from the product page at www.adlinktech.com/Products/PXI\_PXle/PXIControllers/PXI-3982 and install.

Use of Windows 10 requires the following drivers:

▶ Chipset Driver
▶ Graphics Driver
▶ Ethernet/LAN Driver
▶ PXI Trigger I/O Driver
Intel ME Driver
▶ GPIB Driver
Intel RST Driver

The following optional utility programs are also provided:

▶ MAPS Core Windows Software Suite for ADLINK Measurement, Automation, and PXI products
▶ PXI Platform Services

After downloading and extracting a given file, run the executable and follow its instructions to complete installation.

This page intentionally left blank.

# Appendix A PXI Trigger I/O Functions

This appendix describes use of the PXI trigger I/O function library for the PXI controller, to program routing of trigger signals between the trigger I/O SMB connector on the faceplate and the PXI trigger bus on the backplane. API files are located in the installation directory of the PXI Trigger I/O driver.

# A.1 Data Types

The library uses these data types in pxitrigio.h in the directory X:\ADLINK\PXI Trigger IO\Include. It is recommended that you use these data types in your application programs. The table shows the data type names, ranges, and corresponding data types in C/C++, Visual Basic, and Delphi for reference.

<table><tr><td rowspan="2">Type</td><td rowspan="2">Description</td><td rowspan="2">Range</td><td colspan="3">Type</td></tr><tr><td>C/C++ (for 32-bit compiler)</td><td>Visual Basic</td><td>Pascal (Delphi)</td></tr><tr><td>U8</td><td>8-bit ASCII character</td><td>0 to 255</td><td>unsigned char</td><td>Byte</td><td>Byte</td></tr><tr><td>I16</td><td>16-bit signed integer</td><td>-32768 to 32767</td><td>short</td><td>Integer</td><td>SmallInt</td></tr><tr><td>U16</td><td>16-bit unsigned integer</td><td>0 to 65535</td><td>unsigned short</td><td>Not supported by BASIC, use the signed integer (I16) instead</td><td>Word</td></tr><tr><td>I32</td><td>32-bit signed integer</td><td>-2147483648 to 2147483647</td><td>long</td><td>Long</td><td>LongInt</td></tr><tr><td>U32</td><td>32-bit unsigned integer</td><td>0 to 4294967295</td><td>unsigned long</td><td>Not supported by BASIC, use the signed long integer (I32) instead</td><td>Cardinal</td></tr><tr><td>F32</td><td>32-bit single-precision floating-point</td><td>-3.402823E38 to 3.402823E38</td><td>float</td><td>Single</td><td>Single</td></tr><tr><td>F64</td><td>64-bit double-precision floating-point</td><td>1.7976831348 62315E308 to 1.7976831348 62315E309</td><td>double</td><td>Double</td><td>Double</td></tr></table>

# A.2 Function Library

This section provides detailed definitions of the functions available in the function library. Each function includes a description, list of supported cards, syntax, parameter list and Return Code information.

# A.2.1 TRIG\_Init

# Description

Initializes trigger I/O function of PXI controller. TRIG\_Init must be called before the invocation of any other trigger I/O function.

# Syntax

C/C++

I16 TRIG\_Init()

Visual Basic

TRIG\_Init As Integer

# Parameter

None

# Return Code

ERR\_NoError

ERR\_BoardBusy

ERR\_OpenDriverFail

ERR\_GetGPIOAddress

# A.2.2 TRIG\_Close

# Description

Closes trigger I/O function of PXI controller, releasing resources allocated for the trigger I/O function. Users must invoke TRIG\_Close before exiting the application.

# Syntax

```txt
C/C++
I16 TRIG_Close()
Visual Basic
TRIG_Close() As Integer
```

# Parameter

None

# Return Code

```txt
ERR_NoError
ERR_BoardNoInit
```

# A.2.3 TRIG\_SetSoftTrg

# Description

Generates a TTL trigger signal to the trigger I/O SMB connector on the faceplate or the PXI trigger bus on the backplane by software command.

# Syntax

C/C++

I16 TRIG\_SetSoftTrg(U8 Status)

Visual Basic

TRIG\_SetSoftTrg (ByVal status As Byte) As Integer

# Parameters

Status

Logic level of trigger signal.

Available value description:

0: Logic low

1: Logic high

# Return Code

ERR\_NoError

ERR\_BoardNoInit

# A.2.4 TRIG\_Trigger\_Route

# Description

Routes the trigger signal between the trigger I/O SMB connector on the faceplate and the PXI trigger bus on the backplane. This function also allows routing of the software-generated trigger signal to SMB connector or trigger bus.

# Syntax

C/C++

I16 TRIG\_Trigger\_Route (U32 source, U32 dest, U32 halfway)

# Visual Basic

TRIG\_Trigger\_Route (ByVal source As Long, ByVal dest As Long, ByVal halfway As Long) As Integer

# Parameters

source

Source of trigger routing can be one of the following values.

<table><tr><td>Available value</td><td>Description</td></tr><tr><td>PXI_TRIG_VAL_SMB</td><td>SMB connector on the faceplate</td></tr><tr><td>PXI_TRIG_VAL_SOFT</td><td>Software-generated trigger signal</td></tr><tr><td>PXI_TRIG_VAL_TRIG0</td><td>PXI trigger bus #0</td></tr><tr><td>PXI_TRIG_VAL_TRIG1</td><td>PXI trigger bus #1</td></tr><tr><td>PXI_TRIG_VAL_TRIG2</td><td>PXI trigger bus #2</td></tr><tr><td>PXI_TRIG_VAL_TRIG3</td><td>PXI trigger bus #3</td></tr><tr><td>PXI_TRIG_VAL_TRIG4</td><td>PXI trigger bus #4</td></tr><tr><td>PXI_TRIG_VAL_TRIG5</td><td>PXI trigger bus #5</td></tr><tr><td>PXI_TRIG_VAL_TRIG6</td><td>PXI trigger bus #6</td></tr><tr><td>PXI_TRIG_VAL_TRIG7</td><td>PXI trigger bus #7</td></tr></table>

# dest

Destination of trigger routing can be one of the following.

<table><tr><td>Available value</td><td>Description</td></tr><tr><td>PXI_TRIG_VAL_SMB</td><td>SMB connector on the faceplate</td></tr><tr><td>PXI_TRIG_VAL_TRIG0</td><td>PXI trigger bus #0</td></tr><tr><td>PXI_TRIG_VAL_TRIG1</td><td>PXI trigger bus #1</td></tr><tr><td>PXI_TRIG_VAL_TRIG2</td><td>PXI trigger bus #2</td></tr><tr><td>PXI_TRIG_VAL_TRIG3</td><td>PXI trigger bus #3</td></tr><tr><td>PXI_TRIG_VAL_TRIG4</td><td>PXI trigger bus #4</td></tr><tr><td>PXI_TRIG_VAL_TRIG5</td><td>PXI trigger bus #5</td></tr><tr><td>PXI_TRIG_VAL_TRIG6</td><td>PXI trigger bus #6</td></tr><tr><td>PXI_TRIG_VAL_TRIG7</td><td>PXI trigger bus #7</td></tr></table>

# halfway

Halfway point of trigger routing. This parameter is used only to route the software-generated trigger signal to the SMB connector on the faceplate. In this case, the halfway should be set as one of the trigger bus lines, otherwise as PXI\_TRIG\_VAL\_NONE.

<table><tr><td>Available value</td><td>Description</td></tr><tr><td>PXI_TRIG_VAL_NONE</td><td>No halfway point</td></tr><tr><td>PXI_TRIG_VAL_TRIG0</td><td>PXI trigger bus #0</td></tr><tr><td>PXI_TRIG_VAL_TRIG1</td><td>PXI trigger bus #1</td></tr><tr><td>PXI_TRIG_VAL_TRIG2</td><td>PXI trigger bus #2</td></tr><tr><td>PXI_TRIG_VAL_TRIG3</td><td>PXI trigger bus #3</td></tr><tr><td>PXI_TRIG_VAL_TRIG4</td><td>PXI trigger bus #4</td></tr><tr><td>PXI_TRIG_VAL_TRIG5</td><td>PXI trigger bus #5</td></tr><tr><td>PXI_TRIG_VAL_TRIG6</td><td>PXI trigger bus #6</td></tr><tr><td>PXI_TRIG_VAL_TRIG7</td><td>PXI trigger bus #7</td></tr></table>

# Return Code

ERR\_NoError
ERR\_BoardNoInit
ERR\_Set\_Path

# A.2.5 TRIG\_Trigger\_Clear

# Description

Clears the trigger routing setting.

# Syntax

C/C++

I16 TRIG\_Trigger\_Clear()

Visual Basic

TRIG\_Trigger\_Clear() As Integer

# Parameters

None

# Return Code

ERR\_NoError

ERR\_BoardNoInit

ERR\_Trigger\_Clr

# A.2.6 TRIG\_GetSoftTrg

# Description

Acquires the current software trigger state, with default state after system boot of Logic Low.

# Syntax

C/C++

I16 TRIG\_GetSoftTrg(U8 \*Status)

Visual Basic

TRIG\_GetSoftTrg (status As Byte) As Integer

# Parameters

Status

Returns the logic level of software trigger signal.

Returned value:

0: Logic low

1: Logic high

# Return Code

ERR\_NoError

ERR\_BoardNoInit

ERR\_Query\_Status

# A.2.7 TRIG\_Trigger\_Route\_Query

# Description

Acquires the current trigger signal routing path.

# Syntax

```txt
C/C++
```

```txt
I16 TRIG_Trigger_Route_Query (U32* source, U32* dest, U32* halfway)
```

# Visual Basic

TRIG\_Trigger\_Route\_Query (source As Long, dest As Long, halfway As Long) As Integer

# Parameters

source

Returns to the current source of trigger routing, with possible values including:

<table><tr><td>Available Definition</td><td>Defined Value</td></tr><tr><td>PXI_TRIG_VAL_NONE</td><td>0</td></tr><tr><td>PXI_TRIG_VAL_SMB</td><td>2</td></tr><tr><td>PXI_TRIG_VAL_SOFT</td><td>3</td></tr><tr><td>PXI_TRIG_VAL_TRIG0</td><td>111</td></tr><tr><td>PXI_TRIG_VAL_TRIG1</td><td>112</td></tr><tr><td>PXI_TRIG_VAL_TRIG2</td><td>113</td></tr><tr><td>PXI_TRIG_VAL_TRIG3</td><td>114</td></tr><tr><td>PXI_TRIG_VAL_TRIG4</td><td>115</td></tr><tr><td>PXI_TRIG_VAL_TRIG5</td><td>116</td></tr><tr><td>PXI_TRIG_VAL_TRIG6</td><td>117</td></tr><tr><td>PXI_TRIG_VAL_TRIG7</td><td>118</td></tr></table>

# dest

Returns to the current destination of trigger routing, with possible values including:

<table><tr><td>Available Definition</td><td>Defined Value</td></tr><tr><td>PXI_TRIG_VAL_NONE</td><td>0</td></tr><tr><td>PXI_TRIG_VAL_SMB</td><td>2</td></tr><tr><td>PXI_TRIG_VAL_TRIG0</td><td>111</td></tr><tr><td>PXI_TRIG_VAL_TRIG1</td><td>112</td></tr><tr><td>PXI_TRIG_VAL_TRIG2</td><td>113</td></tr><tr><td>PXI_TRIG_VAL_TRIG3</td><td>114</td></tr><tr><td>PXI_TRIG_VAL_TRIG4</td><td>115</td></tr><tr><td>PXI_TRIG_VAL_TRIG5</td><td>116</td></tr><tr><td>PXI_TRIG_VAL_TRIG6</td><td>117</td></tr><tr><td>PXI_TRIG_VAL_TRIG7</td><td>118</td></tr></table>

# halfway

Returns to the current halfway point of trigger routing, with possible values including:

<table><tr><td>Available Value</td><td>Description</td></tr><tr><td>PXI_TRIG_VAL_NONE</td><td>0</td></tr><tr><td>PXI_TRIG_VAL_TRIG0</td><td>111</td></tr><tr><td>PXI_TRIG_VAL_TRIG1</td><td>112</td></tr><tr><td>PXI_TRIG_VAL_TRIG2</td><td>113</td></tr><tr><td>PXI_TRIG_VAL_TRIG3</td><td>114</td></tr><tr><td>PXI_TRIG_VAL_TRIG4</td><td>115</td></tr><tr><td>PXI_TRIG_VAL_TRIG5</td><td>116</td></tr><tr><td>PXI_TRIG_VAL_TRIG6</td><td>117</td></tr><tr><td>PXI_TRIG_VAL_TRIG7</td><td>118</td></tr></table>

# Return Code

ERR\_NoError
ERR\_BoardNoInit
ERR\_Query\_Status

# A.2.8 TRIG\_GetDriverRevision

# Description

Acquires the PXI Trigger software driver version; format of the version number is major.minor1.minor2.

# Syntax

```txt
C/C++
```

```txt
I16 TRIG_GetDriverRevision(unsigned short *major, unsigned short *minor1, unsigned short *minor2)
```

# Visual Basic

```txt
TRIG_GetDriverRevision (major As Integer, minor1 As Integer, minor2 As Integer) As Integer
```

# Parameters

```txt
major
```

Returns the major version number of the pxi trigger software driver

```txt
minor1
```

Returns the first minor version number of the pxi trigger software driver

```txt
minor2
```

Returns the second minor version number of the pxi trigger software driver

# Return Code

```txt
ERR_NoError
```

```txt
ERR_Query_Revision
```

# Appendix B BIOS Setup

# B.1 Entering the BIOS

1. Power on or reboot the PXI controller.
2. Press the &lt;Delete&gt; or &lt;Esc&gt; key when the controller beeps. This should be concurrent with the main startup screen. The BIOS setup program loads after a short delay.
3. The Main menu is displayed when you first enter the BIOS setup program.

The main BIOS setup menu is the first screen that you can navigate. Each main BIOS setup menu option is described in this chapter.

The Main BIOS setup menu screen has two main frames. The left frame displays all the options that can be configured. "Grayed" options cannot be configured, "Blue" options can.

The right frame displays the key legend. Above the key legend is an area reserved for a text message. When an option is selected in the left frame, it is highlighted in white. Often a text message will accompany it.

# B.2 Navigation

The BIOS setup utility uses a key-based navigation system called hot keys. Most hot keys can be used at any time during navigation.

<table><tr><td>Key(s)</td><td>Function</td></tr><tr><td>Right Arrow, Left Arrow</td><td>Moves between different setup menus</td></tr><tr><td>Up Arrow, Down Arrow</td><td>Moves between options within a setup menu</td></tr><tr><td></td><td>Opens a sub-menu or displays all available settings for a highlighted configuration option</td></tr><tr><td></td><td>Returns to the previous menu and shortcuts to the Exit menu from top-level menus</td></tr><tr><td>&lt;+&gt; and &lt;--&gt;</td><td>Cycles between all available settings</td></tr><tr><td></td><td>Selects time and date fields</td></tr><tr><td></td><td>Opens the general help window for the BIOS</td></tr><tr><td></td><td>Loads previous values into the BIOS</td></tr><tr><td></td><td>Restores optimal default values into the BIOS</td></tr><tr><td></td><td>Saves the current configuration and exits BIOS setup</td></tr></table>

Table B-1: BIOS Hot Key Functions

![This image displays a digital icon featuring a white document with horizontal lines, representing text or a list. Overlaid on the document is a large, red checkmark.](.pxi-3982-50-17058-1000-10/fe26516f8f476348e7fd93901df03039202e0cb46806600e2e5e7bc32c6b1440.jpg)
NOTE:

A hot key legend is located in the right frame on most setup screens.

# B.3 Menu Structure

This section presents the primary menus of the BIOS Setup Utility. Use the following table as a quick reference for the contents of the BIOS Setup Utility. The sub-sections that follow provide further details for each top-level menu and sub-menu and the setting options for each menu item. Default setting options are presented in bold and the function of each setting is described in the right hand column of the respective table.

<table><tr><td>Main</td><td>BIOS Information Processor Information PCH Information System Management ▶ System Date and Time</td></tr><tr><td>Advanced</td><td>CPU Configuration ▶ Memory Configuration ▶ Graphics Configuration ▶ Onboard Devices Configuration ▶ USB Configuration ▶ Hardware Health Configuration ▶ TPM Configuration ▶ Hardware Health Configuration ▶</td></tr><tr><td>Security</td><td>Password Description Administrator Password User Password Secure Boot Menu ▶</td></tr><tr><td>Boot</td><td>Boot Configuration CSM Configuration ▶</td></tr><tr><td>Save &amp; Exit</td><td>Save Options Default Options Boot Override</td></tr></table>

Note: ▶ indicates a sub-menu

# B.4 Main

The Main Menu provides read-only information about your system and also allows you to set the System Date and Time. Refer to the tables below for details about each section/sub-menu.

# B.4.1 BIOS Information

<table><tr><td>Feature</td><td>Options</td><td>Description</td></tr><tr><td>BIOS Vendor</td><td>Info only</td><td>American Megatrends</td></tr><tr><td>Core Version</td><td>Info only</td><td>Displays Core version</td></tr><tr><td>Compliancy</td><td>Info only</td><td>Displays compliance information</td></tr><tr><td>Project Version</td><td>Info only</td><td>ADLINK BIOS version</td></tr><tr><td>Build Date and Time</td><td>Info only</td><td>Date the ADLINK BIOS was built</td></tr><tr><td>Access Level</td><td>Info only</td><td>Current BIOS menu access permission</td></tr></table>

# B.4.2 Processor Information

<table><tr><td>Feature</td><td>Options</td><td>Description</td></tr><tr><td>Name</td><td>Info only</td><td>Displays CPU brand name</td></tr><tr><td>Brand String</td><td>Info only</td><td>Displays CPU brand string</td></tr><tr><td>Frequency</td><td>Info only</td><td>Displays CPU frequency</td></tr><tr><td>Processor ID</td><td>Info only</td><td>Displays CPU ID</td></tr><tr><td>Stepping</td><td>Info only</td><td>Displays CPU stepping</td></tr><tr><td>Number of Processors</td><td>Info only</td><td>Displays number of processors</td></tr><tr><td>Microcode Revision</td><td>Info only</td><td>Displays Intel CPU microcode version</td></tr><tr><td>GT Info</td><td>Info only</td><td>Displays GT info of Intel Graphics</td></tr><tr><td>GOP Version</td><td>Info only</td><td>Graphics Output Protocol version</td></tr><tr><td>Memory RC Version</td><td>Info only</td><td>Displays memory version</td></tr><tr><td>Total Memory</td><td>Info only</td><td>Displays installed memory size</td></tr><tr><td>Memory Frequency</td><td>Info only</td><td>Displays memory frequency</td></tr></table>

# B.4.3 PCH Information

<table><tr><td>Feature</td><td>Options</td><td>Description</td></tr><tr><td>Name</td><td>Info only</td><td>Displays PCH name</td></tr><tr><td>PCH SKU</td><td>Info only</td><td>Displays PCH SKU</td></tr><tr><td>Stepping</td><td>Info only</td><td>Displays PCH stepping</td></tr><tr><td>LAN PHY Revision</td><td>Info only</td><td>Displays LAN PHY revision</td></tr><tr><td>ME FW Version</td><td>Info only</td><td>Displays version of ME</td></tr><tr><td>ME Firmware SKU</td><td>Info only</td><td>Displays ME Firmware Kit SKU number</td></tr></table>

# B.4.4 System Management

The System Management sub-menu contains the following five sub-menus with read-only system information.

# B.4.4.1 Board Information

<table><tr><td>Board Information</td><td>Options</td><td>Description</td></tr><tr><td>SEMA Firmware</td><td>Info only</td><td>Displays SEMA firmware</td></tr><tr><td>Build Date</td><td>Info only</td><td>Displays SEMA firmware build date</td></tr><tr><td>SEMA Boot Loader</td><td>Info only</td><td>Displays SEMA boot loader</td></tr><tr><td>Build Date</td><td>Info only</td><td>Displays SEMA boot loader build date</td></tr><tr><td>Hardware Version</td><td>Info only</td><td>Displays SEMA hardware version</td></tr><tr><td>Serial Number</td><td>Info only</td><td>Displays SEMA S/N</td></tr><tr><td>Manufacturing Date</td><td>Info only</td><td>Displays SEMA manufacture date</td></tr><tr><td>Last Repair Date</td><td>Info only</td><td>Displays last SEMA repair date</td></tr><tr><td>MAC ID</td><td>Info only</td><td>Displays SMC MAC ID</td></tr></table>

# B.4.4.2 Temperatures

<table><tr><td>Feature</td><td>Options</td><td>Description</td></tr><tr><td colspan="3">CPU Temperature</td></tr><tr><td>Current</td><td>Info only</td><td>Displays current CPU temperature</td></tr><tr><td>Startup</td><td>Info only</td><td>Displays CPU startup temperature</td></tr><tr><td>Min</td><td>Info only</td><td>Displays min. CPU temperature</td></tr><tr><td>Max</td><td>Info only</td><td>Displays max. CPU temperature</td></tr><tr><td colspan="3">Board Temperature</td></tr><tr><td>Current</td><td>Info only</td><td>Displays current board temperature</td></tr><tr><td>Startup</td><td>Info only</td><td>Displays board startup temperature</td></tr><tr><td>Min</td><td>Info only</td><td>Displays min. board temperature</td></tr><tr><td>Max</td><td>Info only</td><td>Displays max. board temperature</td></tr></table>

# B.4.4.3 Power Consumption

<table><tr><td>Feature</td><td>Options</td><td>Description</td></tr><tr><td>Current Input Current</td><td>Info only</td><td>Displays input current</td></tr><tr><td>Current Input Power</td><td>Info only</td><td>Displays input power</td></tr><tr><td>VCORE</td><td>Info only</td><td>Displays actual voltage of the VCC_CORE</td></tr><tr><td>VGFX</td><td>Info only</td><td>Displays actual voltage of the VGFX</td></tr><tr><td>VMEM</td><td>Info only</td><td>Displays actual voltage of the VMEM</td></tr><tr><td>5VSB</td><td>Info only</td><td>Displays actual voltage of the 5VSB</td></tr><tr><td>VIN</td><td>Info only</td><td>Displays actual voltage of the VIN</td></tr><tr><td>5V</td><td>Info only</td><td>Displays actual voltage of the 5V</td></tr><tr><td>3.3V</td><td>Info only</td><td>Displays actual voltage of the 3.3V</td></tr><tr><td>3.3VSB</td><td>Info only</td><td>Displays actual voltage of the 3.3VSB</td></tr></table>

# B.4.4.4 Runtime Statistics

<table><tr><td>Feature</td><td>Options</td><td>Description</td></tr><tr><td>Total Runtime</td><td>Info only</td><td>Specifies the total time in minutes the system has spent running in S0 state</td></tr><tr><td>Current Runtime</td><td>Info only</td><td>Specifies the time in seconds the system has been running in S0 state, where the counter is cleared when the system is removed from the external power supply</td></tr><tr><td>Power Cycles</td><td>Info only</td><td>Specifies the number of times external power has been shut off</td></tr><tr><td>Boot Cycles</td><td>Info only</td><td>Boot count is increased after a HW- or SW-Reset or successful power-up</td></tr><tr><td>Boot Reason</td><td>Info only</td><td>Shows the event responsible for reboot of the system</td></tr></table>

# B.4.4.5 Flags

<table><tr><td>Feature</td><td>Options</td><td>Description</td></tr><tr><td>BMC Flags</td><td>Info only</td><td></td></tr><tr><td>BIOS Select</td><td>Info only</td><td>Displays the current BIOS ROM selection</td></tr><tr><td>ATX/AT-Mode</td><td>Info only</td><td>Displays ATX/AT mode</td></tr><tr><td>Exception Code</td><td>Info only</td><td>System exception reason</td></tr></table>

# B.4.5 System Date and Time

<table><tr><td>Feature</td><td>Options</td><td>Description</td></tr><tr><td>System Date</td><td>Weekday, MM/DD/YYYY</td><td>Requires alpha-numeric entry of the day of the week, day of the month, calendar month, and all 4 digits of the year, indicating the century and year (Fri XX/XX/20XX)</td></tr><tr><td>System Time</td><td>HH/MM/SS</td><td>Presented as a 24-hour clock in hours, minutes, and seconds</td></tr></table>

# B.5 Advanced

Provides settings for most user interfaces in the system.

B.5.1 CPU Configuration

<table><tr><td>Feature</td><td>Options</td><td>Description</td></tr><tr><td>CPU Signature</td><td>Info only</td><td>Displays CPU signature</td></tr><tr><td>Microcode Patch</td><td>Info only</td><td>Displays microcode revision</td></tr><tr><td>Max CPU Speed</td><td>Info only</td><td>Displays maximum CPU operating Frequency</td></tr><tr><td>Min CPU Speed</td><td>Info only</td><td>Displays minimum CPU operating frequency</td></tr><tr><td>CPU Speed</td><td>Info only</td><td>Displays CPU operating frequency</td></tr><tr><td>Processor Cores</td><td>Info only</td><td>Displays Processor Cores</td></tr><tr><td>Hyper Threading Technology</td><td>Info only</td><td>Displays presence/absence of Intel Hyper Threading support</td></tr><tr><td>Intel VT-x Technology</td><td>Info only</td><td>Displays presence/absence of Intel Virtualization Technology support</td></tr><tr><td>Intel SMX Technology</td><td>Info only</td><td>Displays presence/absence of Intel SMX Technology support</td></tr><tr><td>64-bit</td><td>Info only</td><td>Displays presence/absence of Intel 64-bit support</td></tr><tr><td>EIST Technology</td><td>Info only</td><td>Displays presence/absence of Enhanced Intel SpeedStep Technology</td></tr><tr><td>CPU C3 state</td><td>Info only</td><td>Displays presence/absence of C3 state support</td></tr><tr><td>CPU C6 state</td><td>Info only</td><td>Displays presence/absence of C6 state support</td></tr><tr><td>CPU C7 state</td><td>Info only</td><td>Displays presence/absence of C7 state support</td></tr><tr><td>L1 Data Cache</td><td>Info only</td><td>Displays cache info</td></tr><tr><td>L1 Code Cache</td><td>Info only</td><td>Displays cache info</td></tr><tr><td>L2 Cache</td><td>Info only</td><td>Displays cache info</td></tr><tr><td>L3 Cache</td><td>Info only</td><td>Displays cache info</td></tr><tr><td>L4 Cache</td><td>Info only</td><td>Displays cache info</td></tr><tr><td>Hyper-Threading</td><td>Disabled Enabled</td><td>Enabled for Windows XP and Linux (OS optimized for Hyper-Threading Technology) and disabled for other OS (not optimized); when Disabled only one thread per enabled core is active</td></tr><tr><td>VT-d</td><td>Disabled Enabled</td><td>Enables/disables VT-d function on MCH</td></tr><tr><td>Intel Virtualization Technology</td><td>Disabled Enabled</td><td>Enables/disables support for Intel Virtualization technology</td></tr><tr><td>Intel® SpeedStep(TM)</td><td>Disabled Enabled</td><td>Allows support for more than two frequency ranges</td></tr><tr><td>Turbo Mode</td><td>Disabled Enabled</td><td>Enables/disables turbo mode</td></tr><tr><td>CPU C States</td><td>Enabled Disabled</td><td>Enables/disables CPU C states</td></tr><tr><td>Package C State Limit</td><td>C0/C1C2C3C6C7AUTO</td><td>Maximum Package C State limit</td></tr></table>

B.5.2 Memory Configuration

<table><tr><td>Feature</td><td>Options</td><td>Description</td></tr><tr><td>Memory RC Version</td><td>Info only</td><td>Displays Memory Reference Code version</td></tr><tr><td>Memory Frequency</td><td>Info only</td><td>Displays memory frequency</td></tr><tr><td>Total Memory</td><td>Info only</td><td>Displays total memory</td></tr><tr><td>VDD</td><td>Info only</td><td>Displays the voltage</td></tr><tr><td>DIMM#0</td><td>Info only</td><td>Displays DIMM#0</td></tr><tr><td>DIMM#1</td><td>Info only</td><td>Displays DIMM#1</td></tr><tr><td>Memory Timings (tCL-tRCD-tRP-tRAS)</td><td>Info only</td><td>Displays memory timings</td></tr><tr><td>I2C write Protect control</td><td>ActiveWrite protect</td><td>I2C write Protect control</td></tr><tr><td>SPD Write Protect</td><td>DisabledEnabled</td><td>Enabled: Writes tp SMBus slave addresses A0h – AEh are disabled</td></tr><tr><td>Max TOLUD</td><td>Dynamic1 to 3.5GB</td><td>Maximum Value of TOLUD.Dynamic assignment would adjust TOLUD automatically based on largest MMIO length of installed graphic controller</td></tr></table>

B.5.3 Graphics Configuration

<table><tr><td>Feature</td><td>Options</td><td>Description</td></tr><tr><td>Primary Display</td><td>AutoIGFXPCIE</td><td>Selects which IGFX/PCIE graphics device should be the primary display</td></tr><tr><td>Internal Graphics</td><td>AUTODisabledEnabled</td><td>Keeps IGFX enabled based on the setup options</td></tr><tr><td>Aperture Size</td><td>128MB256MB512M1024MB2048MB4096MB</td><td>Displays maximum CPU operating frequency</td></tr><tr><td>DVMT Pre-Allocated</td><td>32MB4 to2048MB</td><td>Selects DVMT Pre-Allocated (Fixed) Graphics Memory size used by the Internal Graphics Device</td></tr><tr><td>DVMT Total Gfx Mem</td><td>128MB256MBMAX</td><td>Selects DVMT Total Graphics Memory size used by the Internal Graphics Device</td></tr></table>

B.5.4 Onboard Devices Configuration

<table><tr><td>Feature</td><td>Options</td><td>Description</td></tr><tr><td colspan="3">LAN Port Configuration</td></tr><tr><td>LAN1 #1 (Intel I219)</td><td>EnabledDisabled</td><td>Enables/disables onboard I219 LAN controller</td></tr><tr><td>LAN2 #1 (Intel I210)</td><td>EnabledDisabled</td><td>Enables/disables onboard I210 LAN controller</td></tr><tr><td colspan="3">SATA Configuration</td></tr><tr><td>SATA Speed Selection</td><td>DefaultGen1Gen2Gen3</td><td>Indicates the maximum speed the SATA controller can support</td></tr><tr><td>Serial ATA Port</td><td>Info only</td><td>Installed SATA device name</td></tr><tr><td>Software Preserve</td><td>Info only</td><td>Bootable OS in installed SATA device</td></tr><tr><td>SATA Port</td><td>DisabledEnabled</td><td>Enables/disables SATA port</td></tr></table>

B.5.5 USB Configuration

<table><tr><td>Feature</td><td>Options</td><td>Description</td></tr><tr><td>USB Module Version</td><td>Info only</td><td></td></tr><tr><td>USB Controllers</td><td>Info only</td><td>Display USB Controller type</td></tr><tr><td>USB Devices</td><td>Info only</td><td>Lists USB-connected peripheral devices</td></tr><tr><td>Legacy USB Support</td><td>EnabledDisabledAuto</td><td>Enables legacy USB support, where Auto disables legacy support if no USB devices are connected, and Disable retains USB devices only for EFI applications and setup</td></tr><tr><td>XHCI Hand-off</td><td>EnabledDisabled</td><td>A workaround for OS without XHCI hand-off support. XHCI ownership change should be claimed by the XHCI OS driver</td></tr><tr><td>USB Mass Storage Driver Support</td><td>EnabledDisabled</td><td>Enables/disables USB Mass Storage driver support</td></tr><tr><td>Port 60/64 Emulation</td><td>EnabledDisabled</td><td>Enables I/O port 60h/64h emulation; should be enabled for complete USB keyboard legacy support for non-USB aware OS</td></tr><tr><td>USB Transfer Timeout</td><td>1 sec5 sec10 sec20 sec</td><td>Timeout value for Control, Bulk, and Interrupt transfers</td></tr><tr><td>Device Reset Timeout</td><td>10 sec20 sec30 sec40 sec</td><td>USB mass storage device Start Unit command timeout</td></tr><tr><td>Device Power-up Delay</td><td>AutoManual</td><td>Maximum time before the device properly reports itself to the Host Controller. &#x27;Auto&#x27; uses default value: for a Root port, 100 ms, for a Hub port the delay is taken from the Hub descriptor</td></tr></table>

# B.5.6 Network Stack Configuration

<table><tr><td>Feature</td><td>Options</td><td>Description</td></tr><tr><td>Network Stack</td><td>Enabled Disabled</td><td>Enables/disables UEFI network stack</td></tr><tr><td>IPv4 PXE Support</td><td>Enabled Disabled</td><td>Enables/disables IPv4 PXE boot support</td></tr><tr><td>IPv6 PXE Support</td><td>Enabled Disabled</td><td>Enables/disables IPv6 PXE boot support</td></tr><tr><td>PXE Boot Wait Time</td><td>0 sec</td><td>Wait time for ESC key to abort PXE boot</td></tr><tr><td>Media detect count</td><td>1</td><td>Number of times presence of media will be checked</td></tr></table>

# B.5.7 TPM Configuration

<table><tr><td>Feature</td><td>Options</td><td>Description</td></tr><tr><td>Security Device Support</td><td>Disable Enable</td><td>Enable or disable BIOS support for security device</td></tr></table>

# B.5.8 Hardware Health Configuration

<table><tr><td>Feature</td><td>Options</td><td>Description</td></tr><tr><td>System Temperature</td><td>Info only</td><td>Ambient temperature</td></tr><tr><td>+3.3V(System)</td><td>Info only</td><td>System +3.3V voltage</td></tr><tr><td>VBAT</td><td>Info only</td><td>Battery voltage</td></tr><tr><td>+5V(System)</td><td>Info only</td><td>System +5V voltage</td></tr><tr><td>+12V(System)</td><td>Info only</td><td>System +12V voltage</td></tr></table>

# B.6 Security

<table><tr><td>Feature</td><td>Options</td><td>Description</td></tr><tr><td>Password Description</td><td>Info only</td><td>Provides information about password characteristics as well as password length requirements: min. 3, max. 20</td></tr><tr><td>Administrator Password</td><td>Enter password</td><td>If ONLY the Administrator Password is set, then this only limits access to BIOS Setup and is only asked for when entering BIOS Setup</td></tr><tr><td>User Password</td><td>Enter password</td><td>If ONLY the User Password is set, then this is a power on password and must be entered to boot as well as to enter BIOS Setup and while in BIOS Setup the User will have Administrator rights</td></tr><tr><td>HDD Security Configuration</td><td>Enter password</td><td>HDD Security Configuration for selected drive</td></tr><tr><td>Secure Boot menu</td><td>Sub-menu</td><td>See section B.6.1.1 below</td></tr></table>

# B.6.1 Secure Boot Menu

<table><tr><td>Feature</td><td>Options</td><td>Description</td></tr><tr><td>Secure Boot</td><td>DisabledEnabled</td><td>Secure Boot can be enabled if:1. System running in User mode with enrolled Platform Key (PK)2. CSM function is disabled</td></tr><tr><td>Secure Boot Mode</td><td>StandardCustom</td><td>Secure Boot mode selector.Custom mode enables users to change Image Execution policy and manage Secure Boot Keys</td></tr><tr><td>Key Management</td><td>Sub-menu</td><td>See section B.6.1.1 below</td></tr></table>

# B.6.1.1 Key Management

<table><tr><td>Feature</td><td>Options</td><td>Description</td></tr><tr><td>Provision Factory Default Keys</td><td>Disabled Enabled</td><td>Install factory default Secure Boot keys when System is in Setup Mode</td></tr><tr><td>Enroll all Factory Default Keys</td><td>N/A</td><td>Force System to User Mode – install all Factory Default keys (PK, KEK, db, dbt, dbx). Change takes effect after reboot</td></tr><tr><td>Platform Key (PK)</td><td>Set Key</td><td rowspan="5">Enroll Factory Defaults or load the keys from a file with:1. Public Key Certificate in:a) EFI_SIGNATURE_LISTb) EFI_CERT_X509c) EFI_CERT_RSA2048d) EFI_CERT_SHA2562. Authenticated UEFI VariableKey source: Default, Custom,Mixed modified from Setup menu</td></tr><tr><td>Key Exchange Keys</td><td>Set Key</td></tr><tr><td>Authorized Signatures</td><td>Set Key</td></tr><tr><td>Forbidden Signatures</td><td>Set Key</td></tr><tr><td>Authorized TimeStamps</td><td>Set Key</td></tr></table>

B.7 Boot

<table><tr><td>Feature</td><td>Options</td><td>Description</td></tr><tr><td colspan="3">Boot Configuration</td></tr><tr><td>Setup Prompt Timeout</td><td>1</td><td>Number of seconds to wait for setup activation key; to wait indefinitely, set to 65536 (0xFFFF)</td></tr><tr><td>Bootup NumLock State</td><td>On Off</td><td>Set keyboard NumLock state at boot</td></tr><tr><td>Quiet Boot</td><td>Disabled Enabled</td><td>Enable or disable Quiet Boot option</td></tr><tr><td>CSM Configuration</td><td>Sub-menu</td><td>See section B.7.1 on page 56</td></tr><tr><td>Fast Boot</td><td>Disabled Enabled</td><td>Enable or disable boot with initialization of a minimal set of devices required to launch active boot option; has no effect for BBS boot options</td></tr><tr><td>Boot Option Priorities</td><td>Boot Option #1 to Boot Option #8</td><td>Select which potential boot sources should be checked, and in what order, during the boot process</td></tr><tr><td>New Boot Option Policy</td><td>Default Place First Place Last</td><td>Controls the placement of newly detected UEFI boot options</td></tr></table>

B.7.1 CSM Configuration

<table><tr><td>Feature</td><td>Options</td><td>Description</td></tr><tr><td>CSM Support</td><td>EnabledDisabled</td><td>Enables or Disables CSM Support</td></tr><tr><td>CSM16 Module Version</td><td>Info only</td><td>Displays the CSM16 module version number</td></tr><tr><td>GateA20 Active</td><td>Upon RequestAlways</td><td>UPON REQUEST means GA20 can be disabled using BIOS services, ALWAYS means GA20 cannot be disabled; useful when any RT code is executed above 1MB</td></tr><tr><td>INT19 Trap Response</td><td>ImmediatePostponed</td><td>BIOS reaction on INT19 trapping by Option ROM; IMMEDIATE executes trap immediately and POSTPONED executes trap during legacy boot</td></tr><tr><td>Boot Option Filter</td><td>UEFI andLegacyLegacy onlyUEFI only</td><td>Controls to which devices the system can boot</td></tr><tr><td colspan="3">Option ROM Execution</td></tr><tr><td>Network</td><td>Do not launchLegacy onlyUEFI only</td><td>Controls execution of UEFI and Legacy PXE OpROM</td></tr><tr><td>Storage</td><td>Do not launchUEFILegacy only</td><td>Controls execution of UEFI and Legacy Storage OpROM</td></tr><tr><td>Video</td><td>Do not launchUEFILegacy only</td><td>Controls execution of UEFI and Legacy Video OpROM</td></tr><tr><td>Other PCI Devices</td><td>UEFILegacy</td><td>For PCI devices other than Network, Mass Storage, or Video, defines the OpROM to launch</td></tr></table>

# B.8 Save & Exit

<table><tr><td>Feature</td><td>Options</td><td>Description</td></tr><tr><td colspan="3">Save Options</td></tr><tr><td>Save Changes and Exit</td><td></td><td>Saves changes and exits system setup</td></tr><tr><td>Discard Changes and Exit</td><td></td><td>Discards changes and exits system setup</td></tr><tr><td>Save Changes and Reset</td><td></td><td>Saves changes and resets system</td></tr><tr><td>Discard Changes and Reset</td><td></td><td>Discards changes and resets system</td></tr><tr><td>Save Changes</td><td></td><td>Save changes made so far to setup options</td></tr><tr><td>Discard Changes</td><td></td><td>Discards changes made so far to setup options</td></tr><tr><td colspan="3">Default Options</td></tr><tr><td>Restore Defaults</td><td></td><td>Restores/loads default values for all setup options</td></tr><tr><td>Save as User Defaults</td><td></td><td>Saves changes made so far as User Defaults</td></tr><tr><td>Restore User Defaults</td><td></td><td>Restores User Defaults to all setup options</td></tr><tr><td colspan="3">Boot Override</td></tr><tr><td>Launch EFI Shell from filesystem device</td><td></td><td>Attempts to launch EFI shell application (shell.efi) from an available filesystem device</td></tr></table>

This page intentionally left blank.

# Appendix C Dual BIOS

Dual BIOS is a backup function that maintains normal operation of the PXI system module when unexpected boot failure occurs under the default BIOS. Dual BIOS consists of a main BIOS, a backup BIOS, and an independent controller. In normal boot, the main BIOS powers on and boots the system into the OS, monitored by the independent controller. If the main BIOS malfunctions, for example, as the result of corruption incurred by a failed update, boot procedure is terminated abnormally. The backup BIOS is then activated automatically to perform boot procedure. When backup BIOS is activated, during BIOS power-on, notifications are generated indicating that backup BIOS has been deployed. To restore main BIOS function, contact technical support.

This page intentionally left blank.

# Appendix D Legacy Boot Mode Settings

UEFI boot mode is default for the PXI-3982 BIOS.

To boot in legacy boot mode, change related settings in the BIOS menu:

1. Power on and press &lt;DEL&gt; or &lt;ESC&gt; to enter BIOS menu
2. Move to Boot
3. Move to Boot, CSM Configuration
4. Under "CSM Support" select "Enabled"
5. Under "Network" select "Legacy"
6. Under "Storage" select "Legacy"
7. Under "Video" select "Legacy"
8. Under "Other PCI devices" select "Legacy"
9. Press &lt;F10&gt; and &lt;Enter&gt; to save and exit BIOS menu. The system will restart and apply settings for Legacy boot mode.

To restore UEFI boot mode:

1. Power on and press &lt;DEL&gt; or &lt;ESC&gt; to enter BIOS menu
2. Press &lt;F9&gt; and &lt;Enter&gt; to load optimized defaults
3. Press &lt;F10&gt; and &lt;Enter&gt; to save and exit BIOS menu

The system restarts and default settings for UEFI boot mode are applied.

This page intentionally left blank.

# Important Safety Instructions

For user safety, please read and follow all instructions, Warnings, Cautions, and Notes marked in this manual and on the associated device before handling/operating the device, to avoid injury or damage.

S'il vous plaît prêter attention stricte à tous les avertissements et mises en garde figurant sur l'appareil, pour éviter des blessures ou des dommages.

▶ Read these safety instructions carefully.
- Keep the User’s Manual for future reference.
▶ Read the Specifications section of this manual for detailed information on the recommended operating environment.
The device can be operated at an ambient temperature of $55^{\circ}$ C.

\- When installing/mounting or uninstalling/removing device, or when removal of a chassis cover is required for user servicing (See “Getting Started” on page 17.):

▷ Turn off power and unplug any power cords/cables.
▷ Reinstall all chassis covers before restoring power.

▶ To avoid electrical shock and/or damage to device:

▷ Keep device away from water or liquid sources.
▷ Keep device away from high heat or humidity.
▷ Keep device properly ventilated (do not block or cover ventilation openings).

▶ Always use recommended voltage and power source settings.

▶ Always install and operate device near an easily accessible electrical outlet.

▷ Secure the power cord (do not place any object on/over the power cord).

▶ Only install/attach and operate device on stable surfaces and/or recommended mountings.

▶ If the device will not be used for long periods of time, turn off and unplug it from its power source

▶ Never attempt to repair the device, which should only be serviced by qualified technical personnel using suitable tools

▶ A Lithium-type battery may be provided for uninterrupted backup or emergency power.

![The image displays a yellow triangular warning sign with a thick black border. Centered inside the triangle is a large black exclamation point. Below the triangle, the text 'CAUTION:' is printed in black capital letters.](.pxi-3982-50-17058-1000-10/627c79c5275704b33b1cd73a043f6fab6cd1b8a0fa6a76ea26f2c20594ce236d.jpg)

Risk of explosion if battery is replaced with one of an incorrect type; please dispose of used batteries appropriately.

Risque d'explosion si la pile est remplacée par une autre de type incorrect. Veuillez jeter les piles usagées de façon appropriée.

▶ The device must be serviced by authorized technicians when:

▷ The power cord or plug is damaged.
▷ Liquid has entered the device interior.
The device has been exposed to high humidity and/or moisture.
The device is not functioning or does not function according to the User's Manual.
The device has been dropped and/or damaged and/or shows obvious signs of breakage.

▶ Disconnect the power supply cord before loosening the thumbscrews and always fasten the thumbscrews with a screwdriver before starting the system up.

It is recommended that the device be installed only in a server room or computer room where access is:

▶ Restricted to qualified service personnel or users familiar with restrictions applied to the location, reasons therefor, and any precautions required.

▶ Only afforded by the use of a tool or lock and key, or other means of security, and controlled by the authority responsible for the location.

<table><tr><td>&lt;img src="images/d66696f04de938d23de5592d1d70c70e96c7068844a217d47d548a0e5a549195.jpg"/&gt;</td><td>BURN HAZARDTouching this surface could result in bodily injury.To reduce risk, allow the surface to cool before touching.RISQUE DE BRÛLURESNe touchez pas cette surface, cela pourrait entraîner des blessures.Pour éviter tout danger, laissez la surface refroidir avant de la toucher.</td></tr></table>

# Getting Service

Ask an Expert: http://askanexpert.adlinktech.com

# ADLINK Technology, Inc.

9F, No.166 Jian Yi Road, Zhonghe District

New Taipei City 235, Taiwan

Tel: +886-2-8226-5877

Fax: +886-2-8226-5717

Email: service@adlinktech.com

# Ampro ADLINK Technology, Inc.

5215 Hellyer Avenue, #110

San Jose, CA 95138, USA

Tel: +1-408-360-0200

Toll Free: +1-800-966-5200 (USA only)

Fax: +1-408-360-0222

Email: info@adlinktech.com

# ADLINK Technology (China) Co., Ltd.

300 Fang Chun Rd., Zhangjiang Hi-Tech Park

Pudong New Area, Shanghai, 201203 China

Tel: +86-21-5132-8988

Fax: +86-21-5132-3588

Email: market@adlinktech.com

# ADLINK Technology GmbH

Hans-Thoma-Strasse 11

D-68163 Mannheim, Germany

Tel: +49-621-43214-0

Fax: +49-621 43214-30

Email: emea@adlinktech.com

Please visit the Contact page at www.adlinktech.com for information on how to contact the ADLINK regional office nearest you.
[🔗 Link to the original document](.pxi-3982-50-17058-1000-10/pxi-3982-50-17058-1000-10.pdf)