# VPX6200 BIOS

# User’s Manual

Manual Rev.: Rev. 1.0

Revision Date: April 30, 2024

Part No.: 50M-31428-2000

# Preface

# Copyright © 2024 ADLINK Technology, Inc.

This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer.

# Disclaimer

The information in this document is subject to change without prior notice in order to improve reliability, design, and function and does not represent a commitment on the part of the manufacturer.

In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.

# Environmental Responsibility

ADLINK is committed to fulfill its social responsibility to global environmental preservation through compliance with the European Union's Restriction of Hazardous Substances (RoHS) directive and Waste Electrical and Electronic Equipment (WEEE) directive. Environmental protection is a top priority for ADLINK. We have enforced measures to ensure that our products, manufacturing processes, components, and raw materials have as little impact on the environment as possible. When products are at their end of life, our customers are encouraged to dispose of them in accordance with the product disposal and/or recovery programs prescribed by their nation or company.

![Symbol of a trash bin crossed out by two diagonal lines (no text or numbers present)](.vpx6200-bios-50m-31428-2000-10/34635ac6d5dad759f8dc26e38c21bac34f207d95fd94e792a103a87af7e64ee3.jpg)

![The image displays a simple graphic on a white background consisting of three horizontal black rectangles stacked vertically. A large, solid black rectangle dominates the center. Above and below this central rectangle are two thinner, horizontal black bars of equal height. Thin white gaps separate the central rectangle from the top and bottom bars, and all elements are aligned horizontally.](.vpx6200-bios-50m-31428-2000-10/792829e39f0f450ae05a0601d2f724abc8951840ab30e1ed26a961f4e84d0aa8.jpg)

# Trademarks

Product names mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks of their respective companies.

Revision History

<table><tr><td>Revision</td><td>Release Date</td><td>Description of Change(s)</td></tr><tr><td>1.0</td><td>2024-04-30</td><td>Initial release</td></tr></table>

# Table of Contents

# Preface .................

# Table of Contents...

# 1 BIOS Setup Menu .....

1.1 Introduction... .5
1.2 Menu Selection Bar .. ..5
1.3 Menu Conventions.. .5

# 2 Getting Started... 6

2.1 BIOS Information.. .7
2.2 System Information.. .7
2.3 System Date/Time . ..8
2.4 Board Information.. .8

# 3 Advanced Menu ................. . 10

3.1 CPU Configuration.. .. 11
3.2 Power & Performance . .12

3.2.1 CPU – Power Management Control . . 12
3.2.2 GT – Power Management Control.. . 23

3.3 Power Management . ..24
3.3.1 Voltage Monitor .... . 25
3.4 System Management.. ..26
3.4.1 SEMA Flags .. . 27

3.5 Thermal Management . ..28

3.5.1 CPU Thermal Configuration............. .. 29
3.5.2 Platform Thermal Configuration.. . 30
3.5.3 Temperatures .......... ..... 33

3.6 Watchdog Timer .. ..34
3.7 Super IO Configuration.. ..35

3.7.1 NCT5104DSEC Super IO Configuration .......... ..... 35

3.8 VPX Configuration.. ..37
3.9 USB Configuration.. ..39
3.10 AMI Graphic Output Protocol Policy.. ..40
3.11 Serial Port Console Redirection.. ..41
3.12 Network Stack Configuration.. ..42
3.13 Trusted Computing . ..43

# 4 Chipset Menu..... . 45

4.1 System Agent (SA) Configuration . ..46

4.1.1 Memory Configuration ........... .... . 47
4.1.2 PEG Port Feature Configuration........... ...... 48
4.1.3 VMD Setup Menu .......... ...... 48
4.1.4 PCI Express Configuration ............ ..... 49

4.2 PCH-IO Configuration.. ..52

4.2.1 SATA and RST Configuration ... . 54
4.2.2 Software Feature Mask Configuration ... . 56
4.2.3 USB Configuration. 57
4.2.4 Security Configuration .. . 58
4.2.5 HD Audio Configuration ............ . 59

4.2.6 Serial IO Configuration . . 60
4.2.7 PCH Thermal Throttling Control .. . 61

# 5 Server Mgmt Menu ................. . 62

5.1 System Event Log . ..63
5.2 View FRU Information.. ..64
5.3 BMC Network Configuration . ..65
5.4 ADLINK IPMI Configuration . ..66
5.5 View System Event Log.. ..67
5.6 BMC User Settings.. .67

# 6 Security Menu ................... . 68

6.1 Secure Boot.. ..70
7 Boot Menu.... 71
8 Save & Exit... . 73

# Important Safety Instructions..... . 74

# Getting Service ..... .. 76

# 1 BIOS Setup Menu

# 1.1 Introduction

The BIOS setup utility is invoked by pressing &lt;ESC&gt; or &lt;DEL&gt; keys. User can change BIOS settings during setup utility runs. A reset of system is required in order to make new settings take effect.

In BIOS setup utility, there are several hot keys designed for specific purposes. Hot keys are listed below.

 &lt;F1&gt;: General help in setup menu
 &lt;F8&gt;: Load previous BIOS values
 &lt;F9&gt;: Load BIOS default in setup utility
 &lt;F10&gt;: Save & Exit setup utility

# 1.2 Menu Selection Bar

The Menu Selection Bar is located at the top of the screen. It displays the top level available menus to the user:

 Main Menu
 Advanced Menu
 Chipset Menu
 Server Mgmt Menu
 Security Menu
 Boot Menu
 Save & Exit Menu

# 1.3 Menu Conventions

The appearance of setup menu listed in this chapter is a sample to describe the item list. It is shown on VT100 terminal via serial console. Followings are the menu conventions.

# Using color

The mandatory BIOS setup fields are in black. The BIOS setup fields currently not used are in grey. The display only strings are in black.

# Using brackets

Editable menu options are marketed with squares ‘[‘ and ‘]’ to distinguish them from display only fields that can’t be modified.

# 2 Getting Started

The Main Menu provides read-only information about system and also allows to set system’s date and time. Refer to the tables below, it shows the screen shot of Main menu for detail, and submenus and settings as well.

Aptio Setup – AMI

<table><tr><td colspan="3">Main Advanced Chipset Server Mgmt Security Boot Save &amp; Exit</td></tr><tr><td>BIOS Information</td><td></td><td rowspan="16">Set the Date. Use Tab to switch between Date elements.</td></tr><tr><td>BIOS Vendor</td><td>American Megatrends</td></tr><tr><td>BIOS Version</td><td>0.14.10</td></tr><tr><td>Build Date</td><td>04/9/2023</td></tr><tr><td>SEMA Firmware Version</td><td>ADLINK 001</td></tr><tr><td>BMC Firmware Version</td><td>1.04</td></tr><tr><td>MRC Version</td><td>2.2.0.9</td></tr><tr><td>GOP Version</td><td>17.0.1075</td></tr><tr><td>ME FW Version</td><td>15.0.41.2142</td></tr><tr><td>BIOS Boot Source</td><td>Primary BIOS</td></tr><tr><td>System Information</td><td></td></tr><tr><td>Project Name</td><td>VPX-6200</td></tr><tr><td>Product ID</td><td>KX SKU</td></tr><tr><td>System Node</td><td>A</td></tr><tr><td>CPU Board Version</td><td>A1</td></tr><tr><td>CPU Brand String</td><td>Intel(R) Xeon(R) W-1186</td></tr><tr><td></td><td>5MRE @ 2.60GHz</td><td rowspan="9">&lt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; ExitESC: Exit</td></tr><tr><td>CPU Frequency</td><td>2.6GHz</td></tr><tr><td>Total Memory</td><td>32768 MB (DDR4)</td></tr><tr><td>Memory Frequency</td><td>3200 MHz</td></tr><tr><td>PCH SKU</td><td>H RM590E</td></tr><tr><td>&gt; Board Information</td><td></td></tr><tr><td>System Date</td><td>[Thu 01/07/2022]</td></tr><tr><td>System Time</td><td>[16:28:59]</td></tr><tr><td>Access Level</td><td>Administrator</td></tr></table>

# 2.1 BIOS Information

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>BIOS Vendor</td><td>Info-only.American Megatrends</td><td>Display vendor name of system BIOS.</td></tr><tr><td>BIOS Version</td><td>Info-only.x.yy.zz</td><td>Display version of booting BIOS.</td></tr><tr><td>Build Date</td><td>Info-only.MM/DD/YYYY</td><td>It shows the date that BIOS was built.</td></tr><tr><td>SEMA Firmware Version</td><td>Info-only.</td><td>Display version of SEMA EC</td></tr><tr><td>BMC Firmware Version</td><td>Info-only.</td><td>Display version of IPMI</td></tr><tr><td>MRC Version</td><td>Info-only.w.x.y.z</td><td>Display the revision of MRC code which is implemented in BIOS.</td></tr><tr><td>GOP Version</td><td>Info-only.yyyy/x.y.zzzz</td><td>GOP Version: When video option ROM is set to “UEFI Only”, it will show up.</td></tr><tr><td>ME FW Version</td><td>Info-only.ww.x.yy.zzzz</td><td>Display the version of Intel manageability firmware which is implemented in BIOS.</td></tr><tr><td>BIOS Boot Source</td><td>Info-only.Primary BIOS/Backup BIOS</td><td>It shows which BIOS flash boots the system.Primary BIOS: usually means that boots from SPI0Backup BIOS: usually means that boots from SPI1</td></tr></table>

# 2.2 System Information

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>Project Name</td><td>Info-only.VPX-6200</td><td>It shows the project name.</td></tr><tr><td>Product ID</td><td>Info-only.</td><td>It shows the Product ID.KX or KR SKU.</td></tr><tr><td>System Node</td><td>Info-only.</td><td>It shows the System Node.Node A or B.</td></tr><tr><td>CPU Board Version</td><td>Info-only.A1/A2/A3/...</td><td>It shows the CPU board HW version.</td></tr><tr><td>CPU Brand String</td><td>Info-only.Intel(R) Core, ...</td><td>It shows what CPU is booting the system.</td></tr><tr><td>CPU Frequency</td><td>Info-only.XXXX GHz</td><td>It shows CPU&#x27;s frequency.</td></tr><tr><td>Total Memory</td><td>Info-only.XXXX MB (DDRx)</td><td>It shows total memory size used on the motherboard and memory type.</td></tr><tr><td>Memory Frequency</td><td>Info-only.XXXX MHz</td><td>It shows memory&#x27;s frequency.</td></tr><tr><td>PCH SKU</td><td>Info-only.xxxx</td><td>It shows what PCH SKU is designed on motherboard.</td></tr></table>

# 2.3 System Date/Time

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>System Date</td><td>MM/DD/YYYY</td><td>For configuring/showing system date. When setting the Date, usekey to switch between Date elements.</td></tr><tr><td>System Time</td><td>HH:MM:SS</td><td>For configuring/showing system time. When setting the Time, usekey to switch between Time elements.</td></tr><tr><td>Access Level</td><td>Info-only.Administrator/User</td><td>It shows what access level is used to enter BIOS setup menu.</td></tr></table>

# 2.4 Board Information

Aptio Setup – AMI
Main

<table><tr><td colspan="2">Board Information</td><td rowspan="10"></td></tr><tr><td>Serial Number</td><td>N/A</td></tr><tr><td>Manufacturing Date</td><td>N/A</td></tr><tr><td>Last Repair Date</td><td>N/A</td></tr><tr><td>MAC ID</td><td>N/A</td></tr><tr><td colspan="2">Runtime Statistics</td></tr><tr><td>Total Runtime</td><td>12h 51m</td></tr><tr><td>Current Runtime</td><td>0h 01m 29s</td></tr><tr><td>Boot Cycles</td><td>198</td></tr><tr><td>Boot Reason</td><td>Software-reset</td></tr><tr><td></td><td></td><td>&gt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; ExitESC: Exit</td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>Serial Number</td><td>Info-only.</td><td>Display board's serial number.</td></tr><tr><td>Manufacturing Date</td><td>Info-only.</td><td>Display manufacturing date.</td></tr><tr><td>Last Repair Date</td><td>Info-only.</td><td>Display Last Repair Date.</td></tr><tr><td>MAC ID</td><td>Info-only.</td><td>Shows onboard Ethernet's MAC ID.</td></tr><tr><td>Total Runtime</td><td>Info-only.</td><td>The returned value specifies the total time in minutes the system is running in S0 state.</td></tr><tr><td>Current Runtime</td><td>Info-only.</td><td>The returned value specifies the time inseconds the system is running in SO state.This counter is cleared when the system is removed from the external power supply.</td></tr><tr><td>Boot Cycles</td><td>Info-only.</td><td>The boot cycle is increased after a HW or SW reset or after a successful power-up.</td></tr><tr><td>Boot Reason</td><td>Info-only.</td><td>The boot reason is the event which causes the reboot of the system.</td></tr></table>

# 3 Advanced Menu

This menu contains the settings for most of the user interfaces in the system.

Aptio Setup – AMI

<table><tr><td colspan="2">Main Advanced Chipset Server Mgmt Security Boot Save &amp; Exit</td></tr><tr><td rowspan="2">&gt;CPU Configuration&gt;Power &amp; Performance&gt;Power Management&gt;System Management&gt;Thermal Management&gt;Watchdog Timer&gt;Super IO Configuration&gt;VPX Configuration&gt;USB Configuration&gt;AMI Graphic Output Protocol Policy&gt;Serial Port Console Redirection&gt;Network Stack Configuration&gt;Trusted Computing&gt;TLS Auth Configuration&gt;RAM Disk Configuration</td><td>CPU ConfigurationParameters</td></tr><tr><td>&gt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; ExitESC: Exit</td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>CPU Configuration</td><td>Submenu</td><td>For configuring CPU features/functions.</td></tr><tr><td>Power &amp; Performance</td><td>Submenu</td><td>For configuring Power &amp; Performance Options</td></tr><tr><td>Power Management</td><td>Submenu</td><td></td></tr><tr><td>System Management</td><td>Submenu</td><td></td></tr><tr><td>Thermal Management</td><td>Submenu</td><td></td></tr><tr><td>Watchdog Timer</td><td>Submenu</td><td></td></tr><tr><td>Super IO Configuration</td><td>Submenu</td><td></td></tr><tr><td>VPX Configuration</td><td>Submenu</td><td></td></tr><tr><td>USB Configuration</td><td>Submenu</td><td></td></tr><tr><td>AMI Graphic Output Protocol Policy</td><td>Submenu</td><td>User Select Monitor Output by Graphic Output Protocol</td></tr><tr><td>Network Stack Configuration</td><td>Submenu</td><td></td></tr><tr><td>Trusted Computing</td><td>Submenu</td><td></td></tr><tr><td>TLS Auth Configuration</td><td>Submenu</td><td></td></tr><tr><td>RAM Disk Configuration</td><td>Submenu</td><td></td></tr></table>

# 3.1 CPU Configuration

Aptio Setup – AMI
Advanced

<table><tr><td colspan="2">CPU Configuration</td><td rowspan="12"></td></tr><tr><td>Type</td><td>Intel(R) Xeon(R)W-11865MRE@2.60GHz</td></tr><tr><td>Speed</td><td>2600 MHz</td></tr><tr><td>ID</td><td>0x806D1</td></tr><tr><td>Stepping</td><td>R0</td></tr><tr><td>Number of Processors</td><td>8Core(s) / 8Thread(s)</td></tr><tr><td>Microcode Revision</td><td>40</td></tr><tr><td>GT Info</td><td>0x9A70</td></tr><tr><td>eDRAM Size</td><td>N/A</td></tr><tr><td>L1 Instruction Cache</td><td>32 KB x 8</td></tr><tr><td>L2 Cache</td><td>1280 KB x 8</td></tr><tr><td>L3 Cache</td><td>24MB</td></tr><tr><td>L4 Cache</td><td>N/A</td><td rowspan="3">&gt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.</td></tr><tr><td>VMX</td><td>Supported</td></tr><tr><td>SMX/TXT</td><td>Supported</td></tr><tr><td>Intel (VMX) Virtualization</td><td>[Enable]</td><td rowspan="3">F1: General HelpF8: Previous ValuesF9: Optimized Default</td></tr><tr><td>Technology</td><td></td></tr><tr><td>Active Processor Cores</td><td>[All]</td></tr><tr><td>Hyper-Threading</td><td>[Enabled]</td><td rowspan="2">F10: Save &amp; ExitESC: Exit</td></tr><tr><td>Intel Trusted Execution Technology</td><td>[Disabled]</td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>Type</td><td>Info-only.</td><td>It shows what detail CPU information</td></tr><tr><td>Speed</td><td>Info-only.</td><td>It shows what detail CPU information</td></tr><tr><td>ID</td><td>Info-only.</td><td>It shows what detail CPU information</td></tr><tr><td>Stepping</td><td>Info-only.</td><td>It shows what detail CPU information</td></tr><tr><td>Number of Processors</td><td>Info-only.</td><td>It shows what detail CPU information</td></tr><tr><td>Microcode Revision</td><td>Info-only.</td><td>It shows what detail CPU information</td></tr><tr><td>GT Info</td><td>Info-only.</td><td>It shows what detail CPU information</td></tr><tr><td>eDRAM Size</td><td>Info-only.</td><td>It shows what detail CPU information</td></tr><tr><td>L1 Instruction Cache</td><td>Info-only.</td><td>It shows what detail CPU information</td></tr><tr><td>L2 Cache</td><td>Info-only.</td><td>It shows what detail CPU information</td></tr><tr><td>L3 Cache</td><td>Info-only.</td><td>It shows what detail CPU information</td></tr><tr><td>L4 Cache</td><td>Info-only.</td><td>It shows what detail CPU information</td></tr><tr><td>VMX</td><td>Info-only.</td><td>It shows what CPU support feature.</td></tr><tr><td>SMX/TXT</td><td>Info-only.</td><td>It shows what CPU support feature.</td></tr><tr><td>Intel (VMX) Virtualization Technology</td><td>EnabledDisabled</td><td>When enabled, a VMM can utilize the additional hardware capabilities provided by Vanderpool Technology.</td></tr><tr><td>Active Processor Cores</td><td>All / 1 / 2 / 3 / 4 / 5</td><td>Number of cores to enable in each processor package.</td></tr><tr><td>Hyper-Threading</td><td>EnabledDisabled</td><td>Enable or Disable Hyper-Threading Technology.</td></tr><tr><td>Intel Trusted Execution Technology</td><td>EnabledDisabled</td><td>Enables utilization of additional hardware capabilities provided by Intel (R) Trusted Execution Technology.Changes require a full power cycle to take effect.</td></tr></table>

# 3.2 Power & Performance

Aptio Setup – AMI
Advanced

<table><tr><td rowspan="2">&gt;CPU – Power Management Control&gt;GT – Power Management Control</td><td>CPU – Power Management Control Options</td></tr><tr><td>&gt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; ExitESC: Exit</td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>CPU – Power Management Control</td><td>Submenu</td><td>CPU – Power Management Control Options</td></tr><tr><td>GT – Power Management Control</td><td>Submenu</td><td>GT – Power Management Control Options</td></tr></table>

# 3.2.1 CPU – Power Management Control

Aptio Setup – AMI
Advanced

<table><tr><td colspan="2">CPU – Power Management Control</td><td>CPU – Power Management Control Options</td></tr><tr><td>Boot performance mode</td><td>[Turbo Performance]</td><td></td></tr><tr><td>Intel(R) SpeedStep(tm)</td><td>[Disabled]</td><td></td></tr><tr><td>Race To Halt (RTH)</td><td>[Enabled]</td><td></td></tr><tr><td>Intel(R) Speed Shift Technology</td><td>[Enabled]</td><td></td></tr><tr><td>Per Core P State OS control mode</td><td>[Enabled]</td><td></td></tr><tr><td>HwP Autonomous Per Core P State</td><td>[Enabled]</td><td></td></tr><tr><td>HwP Autonomous EPP Grouping</td><td>[Enabled]</td><td></td></tr><tr><td>EPB override over PECI</td><td>[Disabled]</td><td></td></tr><tr><td>HwP Fast MSR Support</td><td>[Enabled]</td><td></td></tr><tr><td>HDC Control</td><td>[Enabled]</td><td></td></tr><tr><td colspan="2">&gt; Config TDP Configurations</td><td></td></tr></table>

<table><tr><td colspan="2">&gt;CPU VR Settings</td></tr><tr><td>Platform PL1 Enable</td><td>[Disabled]</td></tr><tr><td>Platform PL2 Enable</td><td>[Disabled]</td></tr><tr><td>Power Limit 4 Override</td><td>[Disabled]</td></tr><tr><td>C states</td><td>[Disabled]</td></tr><tr><td>Thermal Monitor</td><td>[Enabled]</td></tr><tr><td>Interrupt Redirection Mode Selection</td><td>[Fixed Priority]</td></tr><tr><td>Timed MWAIT</td><td>[Disabled]</td></tr><tr><td colspan="2">&gt;Custom P-state Table</td></tr><tr><td>Energy Performance Gain</td><td>[Disabled]</td></tr><tr><td colspan="2">EPG DIMM ldd3N</td></tr><tr><td colspan="2">EPG DIMM ldd3P</td></tr><tr><td colspan="2">&gt;Power Limit 3 Settings</td></tr><tr><td colspan="2">&gt;CPU Lock Configuration</td></tr></table>

^v: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F8: Previous Values

F9: Optimized Default

F10: Save & Exit

ESC: Exit

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>Boot performance mode</td><td>Max BatteryMax Non-TurboPerformanceTurbo Performance</td><td>Select the performance state that the BIOS will set starting from reset vector.</td></tr><tr><td>Intel(R) SpeedStep(tm)</td><td>EnabledDisabled</td><td>Allows more than two frequency ranges to be supported.</td></tr><tr><td>Race To Halt (RTH)</td><td>EnabledDisabled</td><td>Enable/Disable Race To Halt feature. RTH will dynamically increase CPU frequency in order to enter pkg C-State faster to reduce overall power. (RTH is controlled through MSR 1FC bit 20)</td></tr><tr><td>Intel(R) Speed Shift Technology</td><td>EnabledDisabled</td><td>Enable/Disable Intel(R) Speed Shift Technology support. Enabling will expose the CPPC v2 interface to allow for hardware controlled P-states.</td></tr><tr><td>Per Core P State OS control mode</td><td>EnabledDisabled</td><td>Enable/Disable Per Core P state OS control mode. Disabling will set Bit 31 = 1 command 0x06. When set, the highest core request is used for all other core requests.</td></tr><tr><td>HwP Autonomous Per Core P State</td><td>EnabledDisabled</td><td>Disable Autonomous PCPS (Bit 30 = 1, command 0x11) Autonomous will request the same value for all cores all the time. Enable PCPS (default Bit 30 = 0, command 0x11)</td></tr><tr><td>HwP Autonomous EPP Grouping</td><td>EnabledDisabled</td><td>Enable EPP grouping (default Bit 29 =0, command 0x11) Autonomous will request the same values for all cores with same EPP. Disable EPP grouping (Bit 29 =1 , command 0x11) autonomous will not necessarily request same values for all cores with same EPP.</td></tr><tr><td>EPB override over PECI</td><td>EnabledDisabled</td><td>Enable/Disable EPB override over PECI. Enable by sending pcode command 0x2b , subcommand 0x3 to 1. This will allow OOB EPB PECI override control</td></tr><tr><td>HwP Fast MSR Support</td><td>EnabledDisabled</td><td>Enable/Disable HwP Fast MSR Support for IA32_HWP_REQUEST MSR.</td></tr><tr><td>HDC Control</td><td>EnabledDisabled</td><td>This option allows HDC configuration.</td></tr><tr><td>Config TDP Configurations</td><td>Submenu</td><td></td></tr><tr><td>CPU VR Settings</td><td>Submenu</td><td></td></tr><tr><td>Platform PL1 Enable</td><td>EnabledDisabled</td><td>Enable/Disable Platform Power Limit 1 programming. If this option is enabled, it activates the PL1 value to be used by the processor to limit the average power of given time window.</td></tr><tr><td>Platform PL2 Enable</td><td>EnabledDisabled</td><td>Enable/Disable Platform Power Limit 2 programming. If this option is disabled, BIOS will program the default values for Platform Power Limit 2.</td></tr><tr><td>Power Limit 4 Override</td><td>EnabledDisabled</td><td>Enable/Disable Power Limit 4 override. If this option is disabled, BIOS will leave the default values for Power Limit 4.</td></tr><tr><td>C states</td><td>EnabledDisabled</td><td>Enable/Disable CPU Power Management. Allows CPU to go to C states when it's not 100% utilized.</td></tr><tr><td>Thermal Monitor</td><td>EnabledDisabled</td><td>Enable/Disable Thermal Monitor</td></tr><tr><td>Interrupt Redirection Mode Selection</td><td>Fixed PriorityRound robinHash VectorNo Change</td><td>Interrupt Redirection Mode Select for Logical Interrupts</td></tr><tr><td>Timed MWAIT</td><td>EnabledDisabled</td><td>Enable/Disable Timed MWAIT Support</td></tr><tr><td>Custom P-state Table</td><td>Submenu</td><td></td></tr><tr><td>Energy Performance Gain</td><td>EnabledDisabled</td><td>Enable/disable Energy Performance Gain.</td></tr><tr><td>EPG DIMM ldd3N</td><td>26</td><td>Active standby current (Idd3N) in milliamps from datasheet. Must be calculated on a per DIMM basis.</td></tr><tr><td>EPG DIMM ldd3P</td><td>11</td><td>Active power-down current (Idd3P) in milliamps from datasheet. Must be calculated on a per DIMM basis.</td></tr><tr><td>Power Limit 3 Settings</td><td>Submenu</td><td></td></tr><tr><td>CPU Lock Configuration</td><td>Submenu</td><td></td></tr></table>

# CPU – Power Management Control  Config TDP Configurations

Aptio Setup – AMI

Advanced

Config TDP Configurations

Enable Configurable TDP

Configurable TDP Boot Mode

Configurable TDP Lock

Applies to cTDP

Nominal

Disabled

<table><tr><td>CTDP BIOS control</td><td>Disabled</td><td></td></tr><tr><td>ConfigTDP Levels</td><td>2</td><td></td></tr><tr><td>ConfigTDP Turbo Activation Ratio</td><td>25 (Unlocked)</td><td></td></tr><tr><td>Power Limit 1</td><td>25.0W (MSR:35.0)</td><td></td></tr><tr><td>Power Limit 2</td><td>56.250W (MSR:56.250)</td><td></td></tr><tr><td>Custom Settings Nominal</td><td></td><td></td></tr><tr><td>ConfigTDP Nominal</td><td>Ratio:26 TAR:25</td><td></td></tr><tr><td></td><td>PL1:45.0W</td><td rowspan="7">&gt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; Exit</td></tr><tr><td>Power Limit 1</td><td>25000</td></tr><tr><td>Power Limit 2</td><td>0</td></tr><tr><td>Power Limit 1 Time Window*</td><td>[1]</td></tr><tr><td>ConfigTDP Turbo Activation Ratio</td><td>0</td></tr><tr><td>Custom Settings Down</td><td></td></tr><tr><td>ConfigTDP Level1</td><td>Ratio:21 TAR:20PL1:35.0W</td></tr><tr><td>Power Limit 1</td><td>0</td><td rowspan="4">ESC: Exit</td></tr><tr><td>Power Limit 2</td><td>0</td></tr><tr><td>Power Limit 1 Time Window*</td><td>[0]</td></tr><tr><td>ConfigTDP Turbo Activation Ratio</td><td>0</td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>Enable Configurable TDP</td><td>Applies to non-cTDPApplies to cTDP</td><td>Applies TDP initialization settings based on non-cTDP or cTDP. Default is 1: Applies to cTDP; if 0 then applies non-cTDP and BIOS will bypass cTDP initialization flow</td></tr><tr><td>Configurable TDP Boot Mode</td><td>NominalDownUpDeactivate</td><td>Configurable TDP Mode as Nominal/Up/Down/Deactivate TDP selection. Deactivate option will set MSR to Nominal and MMIO to Zero.</td></tr><tr><td>Configurable TDP Lock</td><td>EnabledDisabled</td><td>Configurable TDP Mode Lock sets the Lock bits on TURBO_ACTIVATION_RATIO and CONFIG_TDP_CONTROL.Note: When CTDP Lock is enabled Custom ConfigTDP Count will be forced to 1 and Custom ConfigTDP Boot Index will be forced to 0.</td></tr><tr><td>CTDP BIOS control</td><td>EnabledDisabled</td><td>Enables CTDP control via runtime ACPI BIOS methods. This "BIOS only" feature does not require EC or driver support.</td></tr><tr><td>ConfigTDP Levels</td><td>Info-only.</td><td></td></tr><tr><td>ConfigTDP Turbo Activation Ratio</td><td>Info-only.</td><td></td></tr><tr><td>Power Limit 1</td><td>Info-only.</td><td></td></tr><tr><td>Power Limit 2</td><td>Info-only.</td><td></td></tr><tr><td>ConfigTDP Nominal</td><td>Info-only.</td><td></td></tr><tr><td>Power Limit 1</td><td>25000</td><td>Power Limit 1 in Milli Watts. BIOS will round to the nearest 1/8W when programming. 0 = no custom override. For 12.50W, enter 12500. Overclocking SKU:Value must be between Max and Min Power Limits (specified by PACKAGE_POWER_SKU_MSR). Other SKUs: This value must be between Min Power Limit and TDP</td></tr><tr><td>Power Limit 2</td><td>0</td><td>Power Limit 2 value in Milli Watts. BIOS will round to the nearest 1/8W when programming. 0 = no custom override. For 12.50W, enter 12500. Processor applies control policies such that the package power does not exceed this limit.</td></tr><tr><td>Power Limit 1 Time Window*</td><td>[0]</td><td>Power Limit 1 Time Window value in seconds. The value may vary from 0 to 128. 0 = default value (28 sec for Mobile and 8 sec for Desktop). Defines time window which TDP value should be maintained.</td></tr><tr><td>ConfigTDP Turbo Activation Ratio</td><td>0</td><td>Custom value for Turbo Activation Ratio. Needs to be configured with valid values from LFM to Max Turbo. 0 means don't use custom value.</td></tr><tr><td>ConfigTDP Level1</td><td>Info-only.</td><td></td></tr><tr><td>Power Limit 1</td><td>0</td><td>Power Limit 1 in Milli Watts. BIOS will round to the nearest 1/8W when programming. 0 = no custom override. For 12.50W, enter 12500. Overclocking SKU: Value must be between Max and Min Power Limits (specified by PACKAGE_POWER_SKU_MSR). Other SKUs: This value must be between Min Power Limit and TDP</td></tr><tr><td>Power Limit 2</td><td>0</td><td>Power Limit 2 value in Milli Watts. BIOS will round to the nearest 1/8W when programming. 0 = no custom override. For 12.50W, enter 12500. Processor applies control policies such that the packagepower does not exceed this limit.</td></tr><tr><td>Power Limit 1 Time Window*</td><td>[0]</td><td>Power Limit 1 Time Window value in seconds. The value may vary from 0 to 128. 0 = default value (28 sec for Mobile and 8 sec for Desktop). Defines time window which TDP value should be maintained.</td></tr><tr><td>ConfigTDP Turbo Activation Ratio</td><td>0</td><td>Custom value for Turbo Activation Ratio. Needs to be configured with valid valuesfrom LFM to Max Turbo. 0 means don't use custom value.</td></tr></table>

# CPU – Power Management Control  CPU VR Settings

Aptio Setup – AMI
Advanced

<table><tr><td colspan="2">CPU VR Settings</td></tr><tr><td>PSYS Slope</td><td>0</td></tr><tr><td>PSYS Offset</td><td>0</td></tr><tr><td>PSYS Prefix</td><td>[+]</td></tr><tr><td>PSYS PMax Power</td><td>0</td></tr><tr><td>Min Voltage Override</td><td>[Disabled]</td></tr><tr><td>&gt; Acoustic Noise Settings</td><td></td></tr><tr><td>&gt; VccIn VR Settings</td><td></td></tr><tr><td>&gt; RFI Settings</td><td></td></tr><tr><td></td><td>&gt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; ExitESC: Exit</td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>PSYS Slope</td><td>0</td><td>PSYS Slope defined in 1/100 increments. Range is 0-200. For a 1.25 slope, enter 125. 0 = AUTO. Uses BIOS VR mailbox command 0x9.&quot;</td></tr><tr><td>PSYS Offset</td><td>0</td><td>PSYS Offset defined in 1/1000 increments. Range is 0-63999. For an offset of 25.348, enter 25348. PSYS Uses BIOS VR mailbox command 0x4.</td></tr><tr><td>PSYS Prefix</td><td>+ -</td><td>Sets the offset value as positive or negative.</td></tr><tr><td>PSYS PMax Power</td><td>0</td><td>PSYS PMax power, defined in 1/8 Watt increments. Range 0-8192. For a PMax of 125W, enter 1000. 0 = AUTO. Uses BIOS VR mailbox command 0xB.</td></tr><tr><td>Min Voltage Override</td><td>Enabled Disabled</td><td>Min Voltage Override. Enable to override minimum voltage for runtime and for C8.</td></tr><tr><td>Acoustic Noise Settings</td><td>Submenu</td><td></td></tr><tr><td>VccIn VR Settings</td><td>Submenu</td><td></td></tr><tr><td>RFI Settings</td><td>Submenu</td><td></td></tr></table>

CPU – Power Management Control  CPU VR Settings Acoustic Noise Settings
Aptio Setup – AMI
Advanced

<table><tr><td colspan="2">Acoustic Noise Settings</td></tr><tr><td>Acoustic Noise Mitigation</td><td>[Disabled]</td></tr><tr><td>Pre Wake Time</td><td>0</td></tr><tr><td>Ramp Up Time</td><td>0</td></tr><tr><td>Ramp Down Time</td><td>0</td></tr><tr><td>VccIn VR Domain</td><td></td></tr><tr><td>Disable Fast PKG C State Ramp for VccIn Domain</td><td>[FALSE]</td></tr><tr><td>Slow Slew Rate for VccIn Domain</td><td>[Fast/2]</td></tr><tr><td></td><td></td></tr><tr><td></td><td></td></tr><tr><td></td><td></td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>Acoustic Noise Mitigation</td><td>EnabledDisabled</td><td>Enabling this option will help mitigate acoustic noise on certain SKUs when the CPU is in deeper C state</td></tr><tr><td>Pre Wake Time</td><td>0</td><td>Set the maximum Pre Wake randomization time in micro ticks. Range is 0-255. This is for acoustic noise mitigation Dynamic Perodicity Alteration (DPA) tuning.</td></tr><tr><td>Ramp Up Time</td><td>0</td><td>Set the maximum Ramp Up randomization time in micro ticks. Range is 0-255. This is for acoustic noise mitigation Dynamic Perodicity Alteration (DPA) tuning.</td></tr><tr><td>Ramp Down Time</td><td>0</td><td>Set the maximum Ramp Down randomization time in micro ticks. Range is 0-255. This is for acoustic noise mitigation Dynamic Perodicity Alteration (DPA) tuning.</td></tr><tr><td>Disable Fast PKG C State Ramp for VccIn Domain</td><td>TRUEFALSE</td><td>This option needs to be configured to reduce acoustic noise during deeper C states. False: Don&#x27;t disable Fast ramp during deeper C states; True: Disable Fast ramp during deeper C state</td></tr><tr><td>Slow Slew Rate for VccIn Domain</td><td>Fast/2Fast/4Fast/8</td><td>Set VR VccIn Slow Slew Rate for Deep Package C State ramp time; Slow slew rate equals to Fast devided by number, the</td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td></td><td>Fast/16</td><td>number is 2, 4, 8, 16 to slow down the slew rate to help minimize acoustic noise</td></tr></table>

CPU – Power Management Control  CPU VR Settings VccIn VR Settings

Aptio Setup – AMI

<table><tr><td colspan="3">Advanced</td></tr><tr><td colspan="2">VccIn VR Domain</td><td rowspan="12"></td></tr><tr><td>VR Config Enable</td><td>[Enabled]</td></tr><tr><td>Current AC Loadline</td><td>170</td></tr><tr><td>Current DC Loadline</td><td>150</td></tr><tr><td>Current Psi1 Threshold</td><td>80</td></tr><tr><td>Current Psi2 Threshold</td><td>20</td></tr><tr><td>Current Psi3 Threshold</td><td>4</td></tr><tr><td>Current Imon Slope</td><td>100</td></tr><tr><td>Current Imon Offset</td><td>1</td></tr><tr><td>Current VR Current Limit</td><td>420</td></tr><tr><td>Current Tdc Current Limit</td><td>488</td></tr><tr><td>AC Loadline</td><td>0</td></tr><tr><td>DC Loadline</td><td>0</td><td rowspan="15">&gt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; ExitESC: Exit</td></tr><tr><td>PS Current Threshold1</td><td>80</td></tr><tr><td>PS Current Threshold2</td><td>20</td></tr><tr><td>PS Current Threshold3</td><td>4</td></tr><tr><td>PS3 Enable</td><td>[Enabled]</td></tr><tr><td>PS4 Enable</td><td>[Enabled]</td></tr><tr><td>IMON Slope</td><td>0</td></tr><tr><td>IMON Offset</td><td>0</td></tr><tr><td>IMON Prefix</td><td>[+]</td></tr><tr><td>VR Current Limit</td><td>0</td></tr><tr><td>TDC Enable</td><td>[Enabled]</td></tr><tr><td>TDC Current Limit</td><td>0</td></tr><tr><td>TDC Time Window</td><td>[1 ms]</td></tr><tr><td>TDC Lock</td><td>[Disabled]</td></tr><tr><td>VccIn Demotion Override Enable</td><td>[Disabled]</td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>VR Config Enable</td><td>EnabledDisabled</td><td>VR Config Enable</td></tr><tr><td>Current AC Loadline</td><td>170</td><td></td></tr><tr><td>Current DC Loadline</td><td>150</td><td></td></tr><tr><td>Current Psi1 Threshold</td><td>80</td><td></td></tr><tr><td>Current Psi2 Threshold</td><td>20</td><td></td></tr><tr><td>Current Psi3 Threshold</td><td>4</td><td></td></tr><tr><td>Current Imon Slope</td><td>100</td><td></td></tr><tr><td>Current Imon Offset</td><td>1</td><td></td></tr><tr><td>Current VR Current Limit</td><td>420</td><td></td></tr><tr><td>Current Tdc Current Limit</td><td>488</td><td></td></tr><tr><td>AC Loadline</td><td>0</td><td>AC Loadline defined in 1/100 mOhms. A value of 100 = 1.00 mOhm, and 1255 = 12.55 mOhm. Range is 0-6249 (0-62.49 mOhms). 0 = AUTO/HW default. Uses BIOS mailbox command 0x2.</td></tr><tr><td>DC Loadline</td><td>0</td><td>DC Loadline defined in 1/100 mOhms. A value of 100 = 1.00 mOhm, and 1255 = 12.55 mOhm. Range is 0-6249 (0-62.49 mOhms). 0 = AUTO/HW default. Uses BIOS mailbox command 0x2.</td></tr><tr><td>PS Current Threshold1</td><td>80</td><td>PS Current Threshold1, defined in 1/4 A increments. A value of 400 = 100A. Range 0-512, which translates to 0-128A. 0 = AUTO. Uses BIOS VR mailbox command 0x3.</td></tr><tr><td>PS Current Threshold2</td><td>20</td><td>PS Current Threshold2, defined in 1/4 A increments. A value of 400 = 100A. Range 0-512, which translates to 0-128A. 0 = AUTO. Uses BIOS VR mailbox command 0x3.</td></tr><tr><td>PS Current Threshold3</td><td>4</td><td>PS Current Threshold3, defined in 1/4 A increments. A value of 400 = 100A. Range 0-512, which translates to 0-128A. 0 = AUTO. Uses BIOS VR mailbox command 0x3.</td></tr><tr><td>PS3 Enable</td><td>EnabledDisabled</td><td>PS3 Enable/Disable. 0 - Disabled, 1 - Enabled. Uses BIOS VR mailbox command 0x3.</td></tr><tr><td>PS4 Enable</td><td>EnabledDisabled</td><td>PS4 Enable/Disable. 0 - Disabled, 1 - Enabled. Uses BIOS VR mailbox command 0x3</td></tr><tr><td>IMON Slope</td><td>0</td><td>IMON Slope defined in 1/100 increments. Range is 0-200. For a 1.25 slope, enter 125. 0 = AUTO. Uses BIOS VR mailbox command 0x4.</td></tr><tr><td>IMON Offset</td><td>0</td><td>IMON Offset defined in 1/1000 increments. Range is 0-63999. For an offset of 25.348, enter 25348. IMON Uses BIOS VR mailbox command 0x4.</td></tr><tr><td>IMON Prefix</td><td>[+]</td><td>Sets the offset value as positive or negative.</td></tr><tr><td>VR Current Limit</td><td>0</td><td>Voltage Regulator Current Limit (Icc Max). This value represents the Maximum instantaneous current allowed at any given time. The value is represented in 1/4 A increments. A value of 400 = 100A. 0 means AUTO. Uses BIOS VR mailbox command 0x6.</td></tr><tr><td>TDC Enable</td><td>EnabledDisabled</td><td>TDC Enable. 0- Disable, 1 - Enable</td></tr><tr><td>TDC Current Limit</td><td>0</td><td>TDC Current Limit, defined in 1/8A increments. Range 0-32767. For a TDC Current Limit of 125A, enter 1000. 0 = 0 Amps. Uses BIOS VR mailbox command 0x1A.</td></tr><tr><td>TDC Time Window</td><td>1 ms, 2 ms, 3 ms, 4 ms, 5 ms, 6 ms, 7 ms, 8 ms, 10 ms</td><td>TDC Time Window, value in milliseconds. 1ms is default. Range from 1ms to 10ms, except for 9ms. 9ms has no valid encoding in the MSR definition.</td></tr><tr><td>TDC Lock</td><td>EnabledDisabled</td><td>TDC Lock</td></tr><tr><td>VccIn Demotion Override Enable</td><td>EnabledDisabled</td><td>Enable VccIn Demotion Override Configuration.</td></tr></table>

# CPU – Power Management Control  CPU VR Settings RFI Settings

Aptio Setup – AMI

Advanced

<table><tr><td>RFI Domain</td><td rowspan="2"></td></tr><tr><td rowspan="2">RFI Current Frequency 140.400MHzRFI Frequency 0Spread Spectrum [Enabled]RFI Spread Spectrum [1.5%]RFI Mitigation [Disabled]</td></tr><tr><td>&gt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; ExitESC: Exit</td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>RFI Current Frequency</td><td>140.400MHz</td><td></td></tr><tr><td>RFI Frequency</td><td>0</td><td>Set desired RFI frequency, in increments of 100KHz. (For a frequency of 100.6MHz, enter 1006.)</td></tr><tr><td>Spread Spectrum</td><td>EnabledDisabled</td><td>Enable or Disable the Spread Spectrum</td></tr><tr><td>RFI Spread Spectrum</td><td>0.5%, 1%, 1.5%, 2%, 3%, 4%, 5%, 6%</td><td>Set the Spread Spectrum</td></tr><tr><td>RFI Mitigation</td><td>EnabledDisabled</td><td>Disable - DCM is the IO_N default; Enable - Enable IO_N DCM/CCM switching as RFI mitigation.</td></tr></table>

# CPU – Power Management Control  Custom P-state Table

Aptio Setup – AMI

<table><tr><td colspan="3">Advanced</td></tr><tr><td rowspan="2">Custom P-state TableNumber of P states</td><td rowspan="2">0</td><td></td></tr><tr><td>&gt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; ExitESC: Exit</td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>Number of P states</td><td>0</td><td>Sets the number of custom P-states. At least 2 states must be present.</td></tr></table>

# CPU – Power Management Control  Power Limit 3 Settings

Aptio Setup – AMI

<table><tr><td rowspan="2">Power Limit 3 Override</td><td rowspan="2">[Disabled]</td><td></td></tr><tr><td>&gt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; ExitESC: Exit</td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>Power Limit 3 Override</td><td>EnabledDisabled</td><td>Enable/Disable Power Limit 3 override. If this option is disabled, BIOS will leave the hardware default values for Power Limit 3 and Power Limit 3 Time Window.</td></tr></table>

CPU – Power Management Control  CPU Lock Configuration
Aptio Setup – AMI

<table><tr><td colspan="3">Advanced</td></tr><tr><td rowspan="2">CFG Lock Overclocking Lock</td><td rowspan="2">[Enabled] [Enabled]</td><td></td></tr><tr><td>&gt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; ExitESC: Exit</td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>CFG Lock</td><td>EnabledDisabled</td><td>Configure MSR 0xE2[15], CFG Lock bit</td></tr><tr><td>Overclocking Lock</td><td>EnabledDisabled</td><td>Enable/Disable Overclocking Lock (BIT 20) in FLEX_RATIO(194) MSR</td></tr></table>

# 3.2.2 GT – Power Management Control

Aptio Setup – AMI

<table><tr><td colspan="3">Advanced</td></tr><tr><td colspan="2">GT – Power Management Control</td><td rowspan="4"></td></tr><tr><td>RC6(Render Standby)</td><td>[Enabled]</td></tr><tr><td>Maximum GT frequency</td><td>[Default Max Frequency]</td></tr><tr><td>Disable Turbo GT frequency</td><td>[Enabled]</td></tr><tr><td></td><td></td><td>&gt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; ExitESC: Exit</td></tr><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>RC6(Render Standby)</td><td>EnabledDisabled</td><td>Check to enable render standby support.</td></tr><tr><td>Maximum GT frequency</td><td>Default MaxFrequency, 100Mhz, 150Mhz, 200Mhz, 250Mhz, 300Mhz, 350Mhz, 400Mhz, 450Mhz, 500Mhz, 550Mhz, 600Mhz, 650Mhz, 700Mhz, 750Mhz, 800Mhz, 850Mhz, 900Mhz, 950Mhz, 1000Mhz, 1050Mhz, 1100Mhz, 1150Mhz, 1200Mhz</td><td>Maximum GT frequency limited by the user. Choose between 350MHz (RPN) and 1350MHz (RP0). Value beyond the range will be clipped to min/max supported by SKU</td></tr><tr><td>Disable Turbo GT frequency</td><td>EnabledDisabled</td><td>Enabled: Disables Turbo GT frequency. Disabled: GT frequency is not limited</td></tr></table>

# 3.3 Power Management

Aptio Setup – AMI
Advanced

<table><tr><td rowspan="2">Power Management&gt; Voltage Monitor</td><td></td></tr><tr><td>&gt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; ExitESC: Exit</td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>Voltage Monitor</td><td>Submenu</td><td></td></tr></table>

# 3.3.1 Voltage Monitor

Aptio Setup – AMI
Advanced

<table><tr><td colspan="2">Voltage Monitor</td><td rowspan="8"></td></tr><tr><td>RTC</td><td>XXX V</td></tr><tr><td>5VSB</td><td>XXX V</td></tr><tr><td>VIN</td><td>XXX V</td></tr><tr><td>3.3V</td><td>XXX V</td></tr><tr><td>VMEM</td><td>XXX V</td></tr><tr><td>3.3VSB</td><td>XXX V</td></tr><tr><td>VCORE</td><td>XXX V</td></tr><tr><td></td><td></td><td>&gt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; ExitESC: Exit</td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>RTC</td><td>Info-only</td><td></td></tr><tr><td>5VSB</td><td>Info-only</td><td></td></tr><tr><td>VIN</td><td>Info-only</td><td></td></tr><tr><td>3.3V</td><td>Info-only</td><td></td></tr><tr><td>VMEM</td><td>Info-only</td><td></td></tr><tr><td>3.3VSB</td><td>Info-only</td><td></td></tr><tr><td>VCORE</td><td>Info-only</td><td></td></tr></table>

# 3.4 System Management

Aptio Setup – AMI
Advanced

<table><tr><td colspan="3">System Management</td></tr><tr><td>SEMA Firmware Version</td><td>ADLINK 001</td><td></td></tr><tr><td colspan="3">&gt; SEMA Flags</td></tr><tr><td colspan="3">SEMA Features:</td></tr><tr><td colspan="3">System Restart Event</td></tr><tr><td colspan="3">4096 Bytes User-Flash</td></tr><tr><td colspan="3">Runtime Watchdog</td></tr><tr><td colspan="3">Temperatures</td></tr><tr><td colspan="3">Voltage Monitor</td></tr><tr><td colspan="3">Power-up Watchdog</td></tr><tr><td colspan="2">Boot Counter</td><td rowspan="11">&gt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; ExitESC: Exit</td></tr><tr><td colspan="2">Dual-BIOS</td></tr><tr><td colspan="2">I2C Bus 2</td></tr><tr><td colspan="2">AT/ATX Mode</td></tr><tr><td colspan="2">ACPI Thermal Trigger</td></tr><tr><td colspan="2">Ext - GPIO</td></tr><tr><td colspan="2">I2C Bus 3</td></tr><tr><td colspan="2">Other BMC</td></tr><tr><td colspan="2">Error Log</td></tr><tr><td colspan="2">Parameter Memory</td></tr><tr><td colspan="2">Ext-GPIO Input Interrupt Support</td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>SEMA Firmware Version</td><td>Info-only</td><td></td></tr><tr><td>SEMA Flags</td><td>Submenu</td><td></td></tr><tr><td>SEMA Features</td><td>Info-only</td><td>If this item is shown below, it means SEMA supports it.</td></tr></table>

# 3.4.1 SEMA Flags

Aptio Setup – AMI
Advanced

<table><tr><td colspan="2">SEMA Flags</td><td rowspan="4"></td></tr><tr><td>SEMA Flags</td><td>0x00</td></tr><tr><td>BMC Select</td><td>Standard BIOS</td></tr><tr><td>ATX/AT-Mode</td><td>AT Mode</td></tr><tr><td></td><td></td><td>&gt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; ExitESC: Exit</td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>Flags</td><td>Info-only</td><td></td></tr><tr><td>SEMA Flags</td><td>Read only</td><td>Show current SEMA settings.</td></tr><tr><td>BMC Select</td><td>Read only</td><td>Display current boot BIOS ROM chip.</td></tr><tr><td>ATX/AT-Mode</td><td>Read only</td><td>Display current power mode setting, AT or ATX mode.</td></tr></table>

# 3.5 Thermal Management

Aptio Setup – AMI
Advanced

<table><tr><td rowspan="2">Thermal Management&gt;CPU Thermal Configuration&gt;Platform Thermal Configuration&gt;Temperatures</td><td></td></tr><tr><td>&gt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; ExitESC: Exit</td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>CPU Thermal Configuration</td><td>Submenu</td><td></td></tr><tr><td>Platform Thermal Configuration</td><td>Submenu</td><td></td></tr><tr><td>Temperatures</td><td>Submenu</td><td></td></tr></table>

# 3.5.1 CPU Thermal Configuration

Aptio Setup – AMI
Advanced

<table><tr><td colspan="2">Cpu Thermal Configuration</td></tr><tr><td>DTS SMM</td><td>[Enabled]</td></tr><tr><td>Tcc Activation Offset</td><td>0</td></tr><tr><td>Tcc Offset Time Window</td><td>[Disabled]</td></tr><tr><td>Tcc Offset Clamp Enable</td><td>[Disabled]</td></tr><tr><td>Tcc Offset Lock Enable</td><td>[Enabled]</td></tr><tr><td>Bi-directional PROCHOT#</td><td>[Enabled]</td></tr><tr><td>Disable PROCHOT# Output</td><td>[Enabled]</td></tr><tr><td>Disable VR Thermal Alert</td><td>[Disabled]</td></tr><tr><td>PROCHOT Response</td><td>[Disabled]</td></tr><tr><td>PROCHOT Lock</td><td>[Disabled]</td></tr><tr><td>ACPI T-States</td><td>[Disabled]</td></tr><tr><td></td><td></td></tr><tr><td></td><td></td></tr><tr><td></td><td></td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>DTS SMM</td><td>EnabledDisabled</td><td>Disabled: ACPI thermal management uses EC reported temperature values.</td></tr><tr><td>Tcc Activation Offset</td><td>0</td><td>Offset from factory set Tcc activation temprature at which the Thermal Control Circuit must be activated. Tcc will be activated at: Tcc Activation Temp - Tcc Activation Offset. Tcc Activation Offset range is 0 to 63.</td></tr><tr><td>Tcc Offset Time Window</td><td>Disabled, 5 ms, 10 ms, 55 ms, 156 ms, 375 ms, 500 ms, 750 ms, 1 sec, 2 sec, 3 sec, 4 sec, 5 sec, 6 sec, 7 sec, 8 sec, 10 sec, 12 sec, 14 sec, 16 sec, 20 sec, 24 sec, 28 sec, 32 sec, 40 sec, 48 sec, 56 sec, 64 sec, 80 sec, 96 sec, 112 sec, 128 sec, 160 sec, 192 sec, 224 sec, 256 sec, 320 sec, 384 sec, 448 sec</td><td>Tcc Offset Time Window for Running Average Temperature Limit(RATL) feature. The Tcc offset time window can range from 5ms to 448s.</td></tr><tr><td>Tcc Offset Clamp Enable</td><td>EnabledDisabled</td><td>Tcc Offset Clamp bit Enable for Running Average Temperature Limit(RATL) feature to allow CPU to throttle below P1.</td></tr><tr><td>Tcc Offset Lock Enable</td><td>EnabledDisabled</td><td>Lock Enable for Running Average Temperature Limit(RATL) feature to lock Temperature Target MSR.</td></tr><tr><td>Bi-directional PROCHOT#</td><td>EnabledDisabled</td><td>When a processor thermal sensor trips (either core), the PROCHOT# will be driven.</td></tr><tr><td>Disable PROCHOT# Output</td><td>EnabledDisabled</td><td>Enable/Disable PROCHOT# Output</td></tr><tr><td>Disable VR Thermal Alert</td><td>EnabledDisabled</td><td>Enable/Disable VR Thermal Alert</td></tr><tr><td>PROCHOT Response</td><td>EnabledDisabled</td><td>Enable/Disable PROCHOT Response</td></tr><tr><td>PROCHOT Lock</td><td>EnabledDisabled</td><td>Enable/Disable PROCHOT Lock</td></tr><tr><td>ACPI T-States</td><td>EnabledDisabled</td><td>Enable/Disable ACPI T-States.</td></tr></table>

# 3.5.2 Platform Thermal Configuration

Aptio Setup – AMI
Advanced

<table><tr><td colspan="2">Platform Thermal Configuration</td><td rowspan="8"></td></tr><tr><td>Critical Trip Point</td><td>[Disabled]</td></tr><tr><td>Passive Trip Point</td><td>[95 C]</td></tr><tr><td>Passive TC1 Value</td><td>1</td></tr><tr><td>Passive TC2 Value</td><td>5</td></tr><tr><td>Passive TSP Value</td><td>10</td></tr><tr><td>Passive Trip Points</td><td>[Enabled]</td></tr><tr><td>Critical Trip Points</td><td>[Disabled]</td></tr><tr><td>PCH Temp Read</td><td>[Enabled]</td><td rowspan="6">&gt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; ExitESC: Exit</td></tr><tr><td>CPU Energy Read</td><td>[Enabled]</td></tr><tr><td>CPU Temp Read</td><td>[Enabled]</td></tr><tr><td>Alert Enable Lock</td><td>[Disabled]</td></tr><tr><td>CPU Temp</td><td>72</td></tr><tr><td>Boot DTS Read</td><td>[Disabled]</td></tr><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>Critical Trip Point</td><td>Disabled, 80 C, 90 C, 95 C, 100 C</td><td>This value controls the temperature of the ACPI Critical Trip Point - the point in which the OS will shut the system off.</td></tr><tr><td>Passive Trip Point</td><td>Disabled, 15 C, 23 C, 31 C, 39 C, 47 C, 55 C, 63 C, 71 C, 79 C, 87 C, 95 C, 103 C, 111 C, 119 C (POR)</td><td>This value controls the temperature of the ACPI Passive Trip Point - the point in which the OS will begin throttling the processor.</td></tr><tr><td>Passive TC1 Value</td><td>1</td><td>This value sets the TC1 value for the ACPI Passive Cooling Formula. Range 1 - 16</td></tr><tr><td>Passive TC2 Value</td><td>5</td><td>This value sets the TC2 value for the ACPI Passive Cooling Formula. Range 1 - 16</td></tr><tr><td>Passive TSP Value</td><td>10</td><td>This item sets the TSP value for the ACPI Passive Cooling Formula. It represents in tenths of a second how often the OS will read the temperature when passive cooling is enabled. Range 2 - 32</td></tr><tr><td>Passive Trip Points</td><td>Enabled Disabled</td><td>Disable Passive Trip Points</td></tr><tr><td>Critical Trip Points</td><td>Enabled Disabled</td><td>Disable Critical Trip Points</td></tr><tr><td>PCH Temp Read</td><td>Enabled Disabled</td><td>PCH Temperature Read Enable</td></tr><tr><td>CPU Energy Read</td><td>Enabled Disabled</td><td>CPU Energy Read Enable</td></tr><tr><td>CPU Temp Read</td><td>Enabled Disabled</td><td>CPU Temperature Read Enable</td></tr><tr><td>Alert Enable Lock</td><td>Enabled Disabled</td><td>Lock all Alert Enable settings</td></tr><tr><td>CPU Temp</td><td>72</td><td>Fail Safe temp that EC will use if OS is hung</td></tr><tr><td>Boot DTS Read</td><td>Enabled Disabled</td><td>Read PCH, CPU DTS Temperature and publish via SMBIOS table</td></tr></table>

# 3.5.3 Temperatures

Aptio Setup – AMI
Advanced

<table><tr><td colspan="2">Temperatures and Fan Speed</td><td rowspan="11"></td></tr><tr><td colspan="2">CPU Temperature</td></tr><tr><td>Current</td><td>xx C</td></tr><tr><td>Startup</td><td>xx C</td></tr><tr><td>Min</td><td>xx C</td></tr><tr><td>Max</td><td>xx C</td></tr><tr><td colspan="2">At the Front Edge Temperatures</td></tr><tr><td>Current</td><td>xx C</td></tr><tr><td>Startup</td><td>xx C</td></tr><tr><td>Min</td><td>xx C</td></tr><tr><td>Max</td><td>xx C</td></tr><tr><td colspan="2">Close to 10G Temperatures</td><td rowspan="6">&lt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; ExitESC: Exit</td></tr><tr><td>Current</td><td>xx C</td></tr><tr><td>Startup</td><td>xx C</td></tr><tr><td colspan="2">Under M.2 Temperatures</td></tr><tr><td>Current</td><td>xx C</td></tr><tr><td>Startup</td><td>xx C</td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>CPU TemperatureCurrent/Startup/Min/Max</td><td>Info-only</td><td></td></tr><tr><td>At the Front EdgeTemperaturesCurrent/Startup/Min/Max</td><td>Info-only</td><td>.</td></tr><tr><td>Close to 10GTemperaturesCurrent/Startup</td><td>Info-only</td><td></td></tr><tr><td>Under M.2 TemperaturesCurrent/Startup</td><td>Info-only</td><td></td></tr></table>

# 3.6 Watchdog Timer

Aptio Setup – AMI
Advanced

<table><tr><td rowspan="2">Watchdog TimerPower-Up Watchdog [Disabled]ATTENTION: Pressing F12 during start up disables the Power Up Watchdog.RunTime Watchdog [Disabled]</td><td></td></tr><tr><td>&gt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; ExitESC: Exit</td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>Power-Up Watchdog</td><td>EnabledDisabled</td><td>The Power Up Watchdog resets the system after a certain amount of time after power up.</td></tr><tr><td>RunTime Watchdog</td><td>EnabledDisabled</td><td>The RunTime Watchdog resets the system after a certain amount of time after power up.</td></tr></table>

# 3.7 Super IO Configuration

Aptio Setup – AMI
Advanced

<table><tr><td rowspan="2">Super IO Configuration&gt; NCT5104DSEC Super IO Configuration</td><td></td></tr><tr><td>&gt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; ExitESC: Exit</td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>NCT5104DSEC Super IO Configuration</td><td>Submenu</td><td></td></tr></table>

# 3.7.1 NCT5104DSEC Super IO Configuration

Aptio Setup – AMI
Advanced

<table><tr><td rowspan="2">NCT5104DSEC Super IO ConfigurationSuper IO Chip NCT5104DSEC&gt; Serial Port 1 Configuration&gt; Serial Port 2 Configuration&gt; Serial Port 3 Configuration</td><td></td></tr><tr><td>&gt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; ExitESC: Exit</td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>Super IO Chip</td><td>Info-only</td><td></td></tr><tr><td>Serial Port x Configuration</td><td>Submenu</td><td></td></tr></table>

# NCT5104DSEC Super IO Configuration  Serial Port x Configuration

Aptio Setup – AMI.

Advanced

<table><tr><td colspan="2">Serial Port x Configuration</td><td rowspan="3"></td></tr><tr><td>Serial PortDevice Settings</td><td>[Enabled]IO=240; IRQ=4;</td></tr><tr><td>Change Settings</td><td>[Auto]</td></tr><tr><td></td><td></td><td>&gt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; ExitESC: Exit</td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>Serial Port</td><td>DisabledEnabled</td><td>Enable or disable serial port (COMx).</td></tr><tr><td>Device Setting</td><td>Info-only</td><td></td></tr><tr><td>Change Settings</td><td>AutoIO=248h;IRQ=7;IO=240h;IRQ=3,4,5,6,7,10,11,12IO=248h;IRQ=3,4,5,6,7,10,11,12IO=250h;IRQ=3,4,5,6,7,10,11,12IO=258h;IRQ=3,4,5,6,7,10,11,12</td><td>Select an optimal setting for Super IO device.</td></tr></table>

# 3.8 VPX Configuration

Aptio Setup – AMI
Advanced

<table><tr><td colspan="2">VPX Configuration</td><td rowspan="11"></td></tr><tr><td>Watchdog ACPI Event Shutdown</td><td>[Disabled]</td></tr><tr><td>COM1 port mode</td><td>[RS232]</td></tr><tr><td>COM2 port mode</td><td>[RS232]</td></tr><tr><td>CPU TDP Power Limit 1 Config</td><td>[25W]</td></tr><tr><td>PCIe Scan Delay</td><td>0</td></tr><tr><td colspan="2">EC GPIO Options</td></tr><tr><td>GPIO Pin Direction</td><td>[Input Mode]</td></tr><tr><td>GPIO Interrupt Setting</td><td>[No interrupt]</td></tr><tr><td>EC_GPIO</td><td>[Interrupt trigger]</td></tr><tr><td>EC_GPI1</td><td>[Interrupt trigger]</td></tr><tr><td>EC_GPI2</td><td>[Interrupt trigger]</td><td>&gt;&lt;: Select Screen</td></tr><tr><td>EC_GPI3</td><td>[Interrupt trigger]</td><td>^v: Select Item</td></tr><tr><td>EC_GPI4</td><td>[Interrupt trigger]</td><td>Enter: Select</td></tr><tr><td>EC_GPI5</td><td>[Interrupt trigger]</td><td>+/-: Change Opt.</td></tr><tr><td>EC_GPI6</td><td>[Interrupt trigger]</td><td>F1: General Help</td></tr><tr><td>EC_GPI7</td><td>[Interrupt trigger]</td><td>F8: Previous Values</td></tr><tr><td>EC_GPO0</td><td>[Low]</td><td>F9: Optimized Default</td></tr><tr><td>EC_GPO1</td><td>[Low]</td><td>F10: Save &amp; Exit</td></tr><tr><td>EC_GPO2</td><td>[Low]</td><td>ESC: Exit</td></tr><tr><td>EC_GPO3</td><td>[Low]</td><td></td></tr><tr><td>EC_GPO4</td><td>[Low]</td><td></td></tr><tr><td>EC_GPO5</td><td>[Low]</td><td></td></tr><tr><td>EC_GPO6</td><td>[Low]</td><td></td></tr><tr><td>EC_GPO7</td><td>[Low]</td><td></td></tr><tr><td>COM2 port mode</td><td>[RS232]</td><td></td></tr><tr><td>Maintenance port mode</td><td>[UART]</td><td></td></tr><tr><td>DP++ manual mode</td><td>[Displayport]</td><td></td></tr><tr><td>PCIe Scan Delay</td><td>0</td><td></td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>Watchdog ACPI Event Shutdown</td><td>DisabledEnabled</td><td>Watchdog ACPI Event ShutdownEnabled/Disabled</td></tr><tr><td>COM1 port mode</td><td>RS232RS422</td><td>COM1 port mode</td></tr><tr><td>COM2 port mode</td><td>RS232RS422</td><td>COM2 port mode</td></tr><tr><td>CPU TDP Power Limit 1 Config</td><td>25W, 35W, 45W</td><td>To config CPU TDP</td></tr><tr><td>PCIe Scan Delay</td><td>0-60</td><td>System delay before PCIe scan. Unit is second and maximum value is 60 seconds</td></tr><tr><td>EC GPIO Options</td><td></td><td></td></tr><tr><td>GPIO Pin Direction</td><td>Input ModeOutput Mode</td><td>Indicates whether the GPIO Pin is interrupted. Write 0x00 to clear the interrupt and EC_GPIO_INT will be changed to high level</td></tr><tr><td>GPIO Interrupt Setting</td><td>No interrupt,Interrupt for both edge trigger,Low level trigger,High level trigger</td><td>When GPIO Pin is input mode, it supports edge trigger and level trigger</td></tr><tr><td>EC_GPIx</td><td>No InterruptInterrupt trigger</td><td>Indicates whether the GPIO Pin is interrupted. Write 0x00 to clear the interrupt and EC_GPIO_INT will be changed to high level</td></tr><tr><td>EC_GPOx</td><td>LowHigh</td><td>Indicates whether the GPIO Pin is interrupted. Write 0x00 to clear the interrupt and EC_GPIO_INT will be changed to high level</td></tr></table>

# 3.9 USB Configuration

Aptio Setup – AMI
Advanced

<table><tr><td colspan="2">USB Configuration</td><td rowspan="7"></td></tr><tr><td>USB Module Version</td><td>26</td></tr><tr><td colspan="2">USB Controllers:1 XHCI</td></tr><tr><td colspan="2">USB Devices:1 Drive, 1 Keyboard, 1 Mouse, 1 Hub</td></tr><tr><td>Legacy USB Support</td><td>[Enabled]</td></tr><tr><td>XHCI Hand-off</td><td>[Enabled]</td></tr><tr><td>USB Mass Storage Driver Support</td><td>[Enabled]</td></tr><tr><td colspan="2">USB hardware delays and time-outs:</td><td rowspan="4">&gt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; ExitESC: Exit</td></tr><tr><td>USB transfer time-out</td><td>[20 sec]</td></tr><tr><td>Device reset time-out</td><td>[20 sec]</td></tr><tr><td>Device power-up delay</td><td>[Auto]</td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>USB Module Version</td><td>Info-only</td><td></td></tr><tr><td>USB Controllers</td><td>Info-only</td><td></td></tr><tr><td>USB Devices</td><td>Info-only</td><td></td></tr><tr><td>Legacy USB Support</td><td>EnabledDisabled</td><td>Enables Legacy USB support. AUTO option disables legacy support if no USB devices are connected. DISABLE option will keep USB devices available only for EFI applications.</td></tr><tr><td>XHCI Hand-off</td><td>EnabledDisabled</td><td>This is a workaround for OSes without XHCI hand-off support. The XHCI ownership change should be claimed by XHCI driver.</td></tr><tr><td>USB Mass Storage Driver Support</td><td>EnabledDisabled</td><td>Enable/Disable USB Mass Storage Driver Support.</td></tr><tr><td>USB transfer time-out</td><td>1 sec, 5 sec, 10 sec,20 sec</td><td>The time-out value for Control, Bulk, and Interrupt transfers.</td></tr><tr><td>Device reset time-out</td><td>10 sec, 20 sec, 30 sec,40 sec</td><td>USB mass storage device Start Unit command time-out.</td></tr><tr><td>Device power-up delay</td><td>Auto, Manual</td><td>Maximum time the device will take before it properly reports itself to the Host Controller. 'Auto' uses default value: for a Root port it is 100 ms, for a Hub port the delay is taken from Hub descriptor.</td></tr></table>

# 3.10 AMI Graphic Output Protocol Policy

Aptio Setup – AMI
Advanced

<table><tr><td rowspan="2">Intel(R) Graphics ControllerIntel(R) GOP Driver [17.0.1075]Output Select [HDMI3[ACTIVE]]</td><td></td></tr><tr><td>&gt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; ExitESC: Exit</td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>Intel(R) GOP Driver</td><td>Info-only</td><td></td></tr><tr><td>Output Select</td><td>HDMI3[ACTIVE]</td><td>Output Interface</td></tr></table>

# 3.11 Serial Port Console Redirection

Aptio Setup – AMI
Advanced

<table><tr><td>COM0Console Redirection [Disabled]&gt; Console Redirection Settings</td><td rowspan="4"></td></tr><tr><td>COM1Console Redirection [Disabled]&gt; Console Redirection Settings</td></tr><tr><td>COM2Console Redirection [Disabled]&gt; Console Redirection Settings</td></tr><tr><td rowspan="2">Serial Port for Out-of-Band Management/Windows Emergency Management Services (EMS)Console Redirection EMS [Disabled]&gt; Console Redirection Settings</td></tr><tr><td>&gt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; ExitESC: Exit</td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>Console Redirection</td><td>DisabledEnabled</td><td>To enable or disable console redirection of COMx.</td></tr><tr><td>Console Redirection Settings</td><td>Submenu</td><td>The settings specify how the host computer and the remote computer (which the user is using) will exchange data. Both computers should have the same or compatible settings.</td></tr></table>

# 3.12 Network Stack Configuration

Aptio Setup – AMI
Advanced

<table><tr><td>Network Stack</td><td>[Disabled]</td><td rowspan="7"></td></tr><tr><td>IPv4 PXE Support</td><td>[Disabled]</td></tr><tr><td>IPv4 HTTP Support</td><td>[Disabled]</td></tr><tr><td>IPv6 PXE Support</td><td>[Disabled]</td></tr><tr><td>IPv6 HTTP Support</td><td>[Disabled]</td></tr><tr><td>PXE boot wait time</td><td>0</td></tr><tr><td>Media detect count</td><td>1</td></tr><tr><td colspan="2"></td><td>&gt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; ExitESC: Exit</td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>Network Stack</td><td>DisabledEnabled</td><td>Enable/Disable UEFI Network Stack</td></tr><tr><td>IPv4 PXE Support</td><td>DisabledEnabled</td><td>Enable/Disable IPv4 PXE boot support. If disabled, IPv4 PXE boot support will not be available.</td></tr><tr><td>IPv4 HTTP Support</td><td>DisabledEnabled</td><td>Enable/Disable IPv4 HTTP boot support. If disabled, IPv4 HTTP boot support will not be available.</td></tr><tr><td>IPv6 PXE Support</td><td>DisabledEnabled</td><td>Enable/Disable IPv6 PXE boot support. If disabled, IPv6 PXE boot support will not be available.</td></tr><tr><td>IPv6 HTTP Support</td><td>DisabledEnabled</td><td>Enable/Disable IPv6 HTTP boot support. If disabled, IPv6 HTTP boot support will not be available.</td></tr><tr><td>PXE boot wait time</td><td>0</td><td>Wait time in seconds to press ESC key to abort the PXE boot. Use either +/- or numeric keys to set the value.</td></tr><tr><td>Media detect count</td><td>1</td><td>Number of times the presence of media will be checked. Use either +/- or numeric keys to set the value.</td></tr></table>

# 3.13 Trusted Computing

Aptio Setup – AMI
Advanced

<table><tr><td colspan="2">TPM 2.0 Device Found</td><td rowspan="10"></td></tr><tr><td>Firmware Version:</td><td>7.85</td></tr><tr><td>Vendor:</td><td>IFX</td></tr><tr><td>Security Device Support</td><td>[Enabled]</td></tr><tr><td>Active PCR banks</td><td>SHA256</td></tr><tr><td>Available PCR banks</td><td>SHA256</td></tr><tr><td>SHA256 PCR Bank</td><td>[Enabled]</td></tr><tr><td>Pending operation</td><td>[None]</td></tr><tr><td>Platform Hierarchy</td><td>[Enabled]</td></tr><tr><td>Storage Hierarchy</td><td>[Enabled]</td></tr><tr><td>Endorsement Hierarchy</td><td>[Enabled]</td><td rowspan="5">&gt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; ExitESC: Exit</td></tr><tr><td>Physical Presence Spec Version</td><td>[1.3]</td></tr><tr><td>TPM 2.0 InterfaceType</td><td>[TIS]</td></tr><tr><td>Device Select</td><td>[Auto]</td></tr><tr><td>Disable Block Sid</td><td>[Disabled]</td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>Firmware Version</td><td>Info-only</td><td></td></tr><tr><td>Vendor</td><td>Info-only</td><td></td></tr><tr><td>Security Device Support</td><td>Disable Enable</td><td>Enables or Disables BIOS support for security device. O.S. will not show Security Device. TCG EFI protocol and INT1A interface will not be available.</td></tr><tr><td>Active PCR banks</td><td>Info-only</td><td></td></tr><tr><td>Available PCR banks</td><td>Info-only</td><td></td></tr><tr><td>SHA256 PCR Bank</td><td>Disable Enable</td><td>Enable or Disable SHA256 PCR Bank</td></tr><tr><td>Pending operation</td><td>None TPM Clear</td><td>Schedule an Operation for the Security Device. NOTE: Your Computer will reboot during restart in order to change State of Security Device.</td></tr><tr><td>Platform Hierarchy</td><td>Disable Enable</td><td>Enable or Disable Platform Hierarchy</td></tr><tr><td>Storage Hierarchy</td><td>Disable Enable</td><td>Enable or Disable Storage Hierarchy</td></tr><tr><td>Endorsement Hierarchy</td><td>Disable Enable</td><td>Enable or Disable Endorsement Hierarchy</td></tr><tr><td>Physical Presence Spec</td><td>1.2</td><td>Select to Tell O.S. to support PPI Spec</td></tr><tr><td>Version</td><td>1.3</td><td>Version 1.2 or 1.3. Note some HCK tests might not support 1.3.</td></tr><tr><td>TPM 2.0 InterfaceType</td><td>CRBTIST</td><td>Select the Communication Interface to TPM 20 Device.</td></tr><tr><td>Device Select</td><td>TPM 1.2TPM 2.0Auto</td><td>TPM 1.2 will restrict support to TPM 1.2 devices, TPM 2.0 will restrict support to TPM 2.0 devices, Auto will support both with the default set to TPM 2.0 devices if not found, TPM 1.2 devices will be enumerated</td></tr><tr><td>Disable Block Sid</td><td>DisableEnable</td><td>Override to allow SID authentication in TCG Storage device.</td></tr></table>

# 4 Chipset Menu

This menu contains the settings for most of the chipset I/O in the system.

Aptio Setup – AMI

<table><tr><td colspan="6">Main Advanced Chipset Server Mgmt Security Boot Save &amp; Exit</td></tr><tr><td rowspan="2" colspan="4">&gt; System Agent (SA) Configuration&gt; PCH-IO Configuration</td><td colspan="2"></td></tr><tr><td colspan="2">&gt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; ExitESC: Exit</td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>System Agent (SA)Configuration</td><td>Submenu</td><td>System Agent (SA) Parameters</td></tr><tr><td>PCH-IO Configuration</td><td>Submenu</td><td>PCH Parameters</td></tr></table>

# 4.1 System Agent (SA) Configuration

Aptio Setup – AMI
Chipset

<table><tr><td colspan="2">System Agent (SA) Configuration</td><td rowspan="7"></td></tr><tr><td>VT-d</td><td>Supported</td></tr><tr><td colspan="2">&gt; Memory Configuration&gt; Graphics Configuration&gt; PEG Port Feature Configuration&gt; VMD setup menu</td></tr><tr><td>Stop Grant Configuration</td><td>[Auto]</td></tr><tr><td>VT-d</td><td>[Enabled]</td></tr><tr><td>X2APIC Opt Out</td><td>[Disabled]</td></tr><tr><td>DMA Control Guarantee</td><td>[Enabled]</td></tr><tr><td>Above 4GB MMIO BIOS assignment</td><td>[Enabled]</td><td>&gt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; ExitESC: Exit</td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>VT-d</td><td>Info-only</td><td></td></tr><tr><td>&gt; Memory Configuration</td><td>Submenu</td><td></td></tr><tr><td>&gt; PEG Port Feature Configuration</td><td>Submenu</td><td></td></tr><tr><td>&gt;VMD setup menu</td><td>Submenu</td><td></td></tr><tr><td>&gt; PCI Express Configuration</td><td>Submenu</td><td></td></tr><tr><td>Stop Grant Configuration</td><td>AutoManual</td><td>Automatic/Manual stop grant configuration</td></tr><tr><td>VT-d</td><td>DisabledEnabled</td><td>VT-d capability</td></tr><tr><td>X2APIC Opt Out</td><td>DisabledEnabled</td><td>Enable/Disable X2APIC_OPT_OUT bit</td></tr><tr><td>DMA Control Guarantee</td><td>DisabledEnabled</td><td>Enable/DisableDMA_CONTROL_GUARANTEE bit</td></tr><tr><td>Above 4GB MMIO BIOS assignment</td><td>DisabledEnabled</td><td>Enable/Disable above 4GBMemoryMappedIO BIOS assignment</td></tr></table>

# 4.1.1 Memory Configuration

Aptio Setup – AMI
Chipset

<table><tr><td colspan="2">Memory Configuration</td><td rowspan="9"></td></tr><tr><td>Memory RC Version</td><td>2.0.2.9</td></tr><tr><td>Memory Speed</td><td>3200 MT/s</td></tr><tr><td>Memory Timings (tCL-tRCD-tRP-tRAS)</td><td>22-22-22-52</td></tr><tr><td>Controller 0 Channel 0 Slot 0</td><td>Populated &amp; Enabled</td></tr><tr><td>Size</td><td>16384 MB (DDR4)</td></tr><tr><td>Number of Ranks</td><td>1</td></tr><tr><td>Manufacturer</td><td>Micron</td></tr><tr><td>Controller 1 Channel 0 Slot 0</td><td>Populated &amp; Enabled</td></tr><tr><td>Size</td><td>16384 MB (DDR4)</td><td>&lt;&lt;: Select Screen</td></tr><tr><td>Number of Ranks</td><td>1</td><td>^v: Select Item</td></tr><tr><td>Manufacturer</td><td>Micron</td><td>Enter: Select+/-: Change Opt.</td></tr><tr><td>Memory Test on Warm Boot</td><td>[Enabled]</td><td>F1: General Help</td></tr><tr><td>Maximum Memory Frequency</td><td>[Auto]</td><td>F8: Previous Values</td></tr><tr><td>ECC Support</td><td>[Enabled]</td><td>F9: Optimized Default</td></tr><tr><td>Max TOLUD</td><td>[Dynamic]</td><td>F10: Save &amp; Exit</td></tr><tr><td>In-Band ECC Support</td><td>[Disabled]</td><td>ESC: Exit</td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>Memory RC Version</td><td>Info-only</td><td></td></tr><tr><td>Memory Speed</td><td>Info-only</td><td></td></tr><tr><td>Memory Timings (tCL-tRCD-tRP-tRAS)</td><td>Info-only</td><td></td></tr><tr><td>Controller X Channel X Slot X</td><td>Info-only</td><td></td></tr><tr><td>Size</td><td>Info-only</td><td></td></tr><tr><td>Number of Ranks</td><td>Info-only</td><td></td></tr><tr><td>Manufacturer</td><td>Info-only</td><td></td></tr><tr><td>Memory Test on Warm Boot</td><td>DisabledEnabled</td><td>Enable Or Disable Base Memory Test Run on Warm Boot</td></tr><tr><td>Maximum Memory Frequency</td><td>Auto</td><td>Maximum Memory Frequency Selections in Mhz.</td></tr><tr><td>ECC Support</td><td>DisabledEnabled</td><td>Enable/disable DDR Ecc Support</td></tr><tr><td>Max TOLUD</td><td>Dynamic, 1 GB, 1.25 GB, 1.5 GB, 1.75 GB, 2 GB, 2.25 GB, 2.5 GB, 2.75 GB, 3 GB, 3.25 GB, 3.5 GB</td><td>Maximum Value of TOLUD. Dynamic assignment would adjust TOLUD automatically based on largest MMIO length of installed graphic controller</td></tr><tr><td>In-Band ECC Support</td><td>Disabled, Enabled</td><td>Enable/Disable In-Band ECC. Either the IBECC or the TME can be enabled.</td></tr></table>

# 4.1.2 PEG Port Feature Configuration

Aptio Setup – AMI
Chipset

<table><tr><td rowspan="2">PEG Port Feature ConfigurationDetect Non-Compliance Device [Disabled]</td><td></td></tr><tr><td>&gt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; ExitESC: Exit</td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>Detect Non-Compliance Device</td><td>DisabledEnabled</td><td>Detect Non-Compliance PCI Express Device in PEG</td></tr></table>

# 4.1.3 VMD Setup Menu

Aptio Setup – AMI
Chipset

<table><tr><td colspan="2">VMD Configuration</td><td rowspan="9"></td></tr><tr><td>Enable VMD controller</td><td>[Disabled]</td></tr><tr><td>Enabled VMD Global Mapping</td><td>[Enabled]</td></tr><tr><td>Map this Root Port under VMD</td><td>[Enabled]</td></tr><tr><td>Root Port BDF details</td><td>SATA Controller</td></tr><tr><td>RAID0</td><td>[Enabled]</td></tr><tr><td>RAID1</td><td>[Enabled]</td></tr><tr><td>RAID5</td><td>[Enabled]</td></tr><tr><td>Intel(R) OptaneTM Memory</td><td>[Enabled]</td></tr><tr><td></td><td></td><td>&gt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; Exit</td></tr></table>

ESC: Exit

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>Enable VMD controller</td><td>DisabledEnabled</td><td>Enable/Disable to VMD controller</td></tr><tr><td>Enabled VMD Global Mapping</td><td>DisabledEnabled</td><td>Enable/Disable to VMD Global Mapping</td></tr><tr><td>Map this Root Port under VMD</td><td>DisabledEnabled</td><td>Enable/Disable to Map this Root Port under VMD</td></tr><tr><td>Root Port BDF details</td><td>Info-only</td><td></td></tr><tr><td>RAID0</td><td>DisabledEnabled</td><td>Enable/Disable to RAID0</td></tr><tr><td>RAID1</td><td>DisabledEnabled</td><td>Enable/Disable to RAID1</td></tr><tr><td>RAID5</td><td>DisabledEnabled</td><td>Enable/Disable to RAID5</td></tr><tr><td>Intel(R) OptaneTM Memory</td><td>DisabledEnabled</td><td>Enable/Disable System Acceleration with Intel(R) OptaneTM Memory feature.</td></tr></table>

# 4.1.4 PCI Express Configuration

Aptio Setup – AMI

Chipset

PCI Express Configuration

PCI Express Clock Gating

PCI Express Power Gating

PCIe function swap

> PCI Express Root Port 1

> PCI Express Root Port 2

> PCI Express Root Port 3

> PCI Express Root Port 4

[Enabled]

[Enabled]

[Enabled]

>&lt;: Select Screen

^v: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F8: Previous Values

F9: Optimized Default

F10: Save & Exit

ESC: Exit

&lt;table&gt;<tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>PCI Express Clock Gating</td><td>DisabledEnabled</td><td>PCI Express Clock Gating Enable/Disablefor each root port.</td></tr><tr><td>PCI Express Power Gating</td><td>DisabledEnabled</td><td>PCI Express Power Gating Enable/Disable for each root port.</td></tr><tr><td>PCIe function swap</td><td>DisabledEnabled</td><td>When Disabled, prevents PCIE rootport function swap. If any function other than 0th is enabled, 0th will become visible.</td></tr><tr><td>&gt; PCI Express Root Port 1</td><td>Submenu</td><td></td></tr><tr><td>&gt; PCI Express Root Port 2</td><td>Submenu</td><td></td></tr><tr><td>&gt; PCI Express Root Port 3</td><td>Submenu</td><td></td></tr><tr><td>&gt; PCI Express Root Port 4</td><td>Submenu</td><td></td></tr></table>

# PCI Express Configuration  PCI Express Root Port X

Aptio Setup – AMI

Chipset

<table><tr><td>PCI Express Root Port 1</td><td>[Enabled]</td><td rowspan="34"></td></tr><tr><td>Connection Type</td><td>[Slot]</td></tr><tr><td>ASPM</td><td>[Disabled]</td></tr><tr><td>L1 Substates</td><td>[L1.1 &amp; L1.2]</td></tr><tr><td>Gen3 Eq Phase3 Method</td><td>[Hardware]</td></tr><tr><td>Gen4 Eq Phase3 Method</td><td>[Hardware]</td></tr><tr><td>ACS</td><td>[Enabled]</td></tr><tr><td>PTM*</td><td>[Enabled]</td></tr><tr><td>DPC</td><td>[Enabled]</td></tr><tr><td>FOM Scoreboard Control Policy</td><td>[Auto]</td></tr><tr><td>VC</td><td>[Enabled]</td></tr><tr><td>Multi-VC</td><td>[Disabled]</td></tr><tr><td>EDPC</td><td>[Enabled]</td></tr><tr><td>URR</td><td>[Disabled]</td></tr><tr><td>FER</td><td>[Disabled]</td></tr><tr><td>NFER</td><td>[Disabled]</td></tr><tr><td>CER</td><td>[Disabled]</td></tr><tr><td>CTO</td><td>[Disabled]</td></tr><tr><td>SEFE</td><td>[Disabled]</td></tr><tr><td>SENFE</td><td>[Disabled]</td></tr><tr><td>SECE</td><td>[Disabled]</td></tr><tr><td>PME SCI</td><td>[Disabled]</td></tr><tr><td>Hot Plug</td><td>[Disabled]</td></tr><tr><td>Advanced Error Reporting</td><td>[Enabled]</td></tr><tr><td>PCIe Speed</td><td>[Auto]</td></tr><tr><td>IOTG Mode</td><td>[Enabled]</td></tr><tr><td>Transmitter Half Swing</td><td>[Disabled]</td></tr><tr><td>Detect Timeout</td><td>0</td></tr><tr><td>P2P Support</td><td>[Disabled]</td></tr><tr><td colspan="2">SA PCIe LTR Configuration</td></tr><tr><td>LTR</td><td>[Enabled]</td></tr><tr><td>Snoop Latency Override</td><td>[Auto]</td></tr><tr><td>Non Snoop Latency Override</td><td>[Auto]</td></tr><tr><td>Force LTR Override</td><td>[Disabled]</td></tr><tr><td colspan="2"></td><td>&lt;: Select Screen</td></tr><tr><td>LTR Lock</td><td>[Disabled]</td><td>^v: Select ItemEnter: Select</td></tr><tr><td>CPU PCIe Gen3 HWEQ Config</td><td></td><td>+/-: Change Opt.</td></tr><tr><td>UPTP</td><td>7</td><td>F1: General Help</td></tr><tr><td>DPTP</td><td>7</td><td>F8: Previous ValuesF9: Optimized Default</td></tr><tr><td>CPU PCIe Gen4 HWEQ Config</td><td></td><td>F10: Save &amp; Exit</td></tr><tr><td>UPTP</td><td>8</td><td>ESC: Exit</td></tr><tr><td>DPTP</td><td>9</td><td></td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>PCI Express Root Port 1</td><td>Disabled, Enabled</td><td>Control the PCI Express Root Port.</td></tr><tr><td>Connection Type</td><td>Built-in, Slot</td><td>Built-In: a built-in device is connected to this root port. Slo tImplemented bit will be clear.Slot: this root port connects to user-accessible slot. Slot Implemented bit will be set.</td></tr><tr><td>ASPM</td><td>Disabled, L1</td><td>Set the ASPM Level:</td></tr><tr><td>L1 Substates</td><td>Disabled, L1.1, L1.1 &amp; L1.2</td><td>PCI Express L1 Substates settings. L1SS cannot be enabled when CLKREQMSG is disabled</td></tr><tr><td>Gen3 Eq Phase3 Method</td><td>Hardware, Static Coeff.</td><td>PCIe Gen3 Equalization Phase 3 Method</td></tr><tr><td>Gen4 Eq Phase3 Method</td><td>Hardware, Static Coeff.</td><td>PCIe Gen3 Equalization Phase 3 Method</td></tr><tr><td>ACS</td><td>Disabled, Enabled</td><td>Enable/Disable Access Control Services Extended Capability</td></tr><tr><td>PTM*</td><td>Disabled, Enabled</td><td>Enable/Disable Precision Time Measurement</td></tr><tr><td>DPC</td><td>Disabled, Enabled</td><td>Enable/Disable Downstream Port Containment</td></tr><tr><td>FOM Scoreboard Control Policy</td><td>Auto, Gen3, Gen4, Gen3/Gen4</td><td>Select the FOM Scoreboard Control Policy, when set to Auto, speed is based on TLS</td></tr><tr><td>VC</td><td>Disabled, Enabled</td><td>Enable/Disable Virtual Channel</td></tr><tr><td>Multi-VC</td><td>Disabled, Enabled</td><td>Enable/Disable Multi Virtual Channel</td></tr><tr><td>EDPC</td><td>Disabled, Enabled</td><td>Enable/Disable Rootport extensions for Downstream Port Containment</td></tr><tr><td>URR</td><td>Disabled, Enabled</td><td>PCI Express Unsupported Request Reporting Enable/Disable.</td></tr><tr><td>FER</td><td>Disabled, Enabled</td><td>PCI Express Device Fatal Error Reporting Enable/Disable.</td></tr><tr><td>NFER</td><td>Disabled, Enabled</td><td>PCI Express Device Non-Fatal Error Reporting Enable/Disable.</td></tr><tr><td>CER</td><td>Disabled, Enabled</td><td>PCI Express Device Correctable Error Reporting Enable/Disable.</td></tr><tr><td>CTO</td><td>Disabled, Enabled</td><td>PCI Express Completion Timer TO Enable/Disable.</td></tr><tr><td>SEFE</td><td>Disabled, Enabled</td><td>Root PCI Express System Error on Fatal Error Enable/Disable.</td></tr><tr><td>SENFE</td><td>Disabled, Enabled</td><td>Root PCI Express System Error on Non-Fatal Error Enable/Disable.</td></tr><tr><td>SECE</td><td>Disabled, Enabled</td><td>Root PCI Express System Error on CorrectableError Enable/Disable.</td></tr><tr><td>PME SCI</td><td>Disabled, Enabled</td><td>PCI Express PME SCI Enable/Disable.</td></tr><tr><td>Hot Plug</td><td>Disabled, Enabled</td><td>PCI Express Hot Plug Enable/Disable.</td></tr><tr><td>Advanced Error Reporting</td><td>Disabled, Enabled</td><td>Advanced Error Reporting Enable/Disable.</td></tr><tr><td>PCIe Speed</td><td>Auto, Gen1, Gen2, Gen3, Gen4</td><td>Configure PCIe Speed</td></tr><tr><td>IOTG Mode</td><td>Disabled, Enabled</td><td>IOTG Mode Enable/Disable</td></tr><tr><td>Transmitter Half Swing</td><td>Disabled, Enabled</td><td>Transmitter Half Swing Enable/Disable.</td></tr><tr><td>Detect Timeout</td><td>[ Max-Value, Min-Value, Step-Value] = [ 0xFFFF, 0x0000, 0x0001]</td><td>The number of milliseconds reference code will wait for link to exit Detect state for enabled ports before assuming there is no device and potentially disabling the port.</td></tr><tr><td>P2P Support</td><td>Disabled, Enabled</td><td>Program P2P Support Registers according to setup option</td></tr><tr><td>LTR</td><td>Disabled, Enabled</td><td>SA PCIE Latency Reporting Enable/Disable</td></tr><tr><td>Snoop Latency Override</td><td>Disabled, Manual, Auto</td><td>Snoop Latency Override for SA PCIE.</td></tr><tr><td>Non Snoop Latency Override</td><td>Disabled, Manual, Auto</td><td>Non Snoop Latency Override for SA PCIE.</td></tr><tr><td>Force LTR Override</td><td>Disabled, Enabled</td><td>Force LTR Override for SA PCIE.</td></tr><tr><td>LTR Lock</td><td>Disabled, Enabled</td><td>PCIE LTR Configuration Lock</td></tr><tr><td>UPTP</td><td>[ Max-Value, Min-Value, Step-Value] = [ 0x0A, 0x00, 0x01]</td><td>Upstream Port Transmitter Preset</td></tr><tr><td>DPTP</td><td>[ Max-Value, Min-Value, Step-Value] = [ 0x0A, 0x00, 0x01]</td><td>Downstream Port Transmitter Preset</td></tr></table>

# 4.2 PCH-IO Configuration

Aptio Setup – AMI

Chipset

PCH-IO Configuration

> SATA And RST Configuration
> USB Configuration
> Security Configuration
> HD Audio Configuration
> SerialIo Configuration
> Pch Thermal Throttling Control
> TSN GBE Configuration

Port 80h Redirection

Enhance Port 80h LPC Decoding

Enable TCO Timer

Enable Timed GPIO0

Enable Timed GPIO1

WOL From S5

[LPC Bus]

[Enabled]

[Enabled]

[Disabled]

[Disabled]

>&lt;: Select Screen

^v: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F8: Previous Values

F9: Optimized Default

F10: Save & Exit

ESC: Exit

&lt;table&gt;<tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>&gt;SATA And RST Configuration</td><td>Submenu</td><td></td></tr><tr><td>&gt;USB Configuration</td><td>Submenu</td><td></td></tr><tr><td>&gt;Security Configuration</td><td>Submenu</td><td></td></tr><tr><td>&gt;HD Audio Configuration</td><td>Submenu</td><td></td></tr><tr><td>&gt;Seriallo Configuration</td><td>Submenu</td><td></td></tr><tr><td>&gt;Pch Thermal Throttling Control</td><td>Submenu</td><td></td></tr><tr><td>&gt;TSN GBE Configuration</td><td>Submenu</td><td></td></tr><tr><td>Port 80h Redirection</td><td>LPC BusPCIE Bus</td><td>Control where the Port 80h cycles are sent.</td></tr><tr><td>Enhance Port 80h LPC Decoding</td><td>DisabledEnabled</td><td>Support the word/dword decoding of port 80h behind LPC</td></tr><tr><td>Enable TCO Timer</td><td>DisabledEnabled</td><td>Enable/Disable TCO timer. When disabled, it disables PCH ACPI timer, stops TCO timer, and ACPI WDAT table will not be published.</td></tr><tr><td>Enable Timed GPIO0</td><td>DisabledEnabled</td><td>Enable/Disable Timed GPIO0. When disabled, it disables cross time stamp time-synchronization as extension of Hammock Harbor time synchronization.</td></tr><tr><td>Enable Timed GPIO1</td><td>DisabledEnabled</td><td>Enable/Disable Timed GPIO1. When disabled, it disables cross time stamp time-synchronization as extension of Hammock Harbor time synchronization.</td></tr><tr><td>WOL From S5</td><td>OFFON</td><td>This Config to control power on/off LAN in S5 State by SEMA(EC).</td></tr></table>

# 4.2.1 SATA and RST Configuration

Aptio Setup – AMI

Chipset

<table><tr><td colspan="2">SATA And RST Configuration</td><td rowspan="11"></td></tr><tr><td>SATA Controller(s)</td><td>[Enabled]</td></tr><tr><td>SATA Mode Selection</td><td>[AHCI]</td></tr><tr><td>SATA Test Mode</td><td>[Disabled]</td></tr><tr><td colspan="2">&gt; Software Feature Mask Configuration</td></tr><tr><td>Aggressive LPM Support</td><td>[Enabled]</td></tr><tr><td>SATA Controller Speed</td><td>[Gen3]</td></tr><tr><td>Serial ATA Port X</td><td>XXXX</td></tr><tr><td>Software Preserve</td><td>Unknown</td></tr><tr><td>Port X</td><td>[Enabled]</td></tr><tr><td>Hot Plug</td><td>[Disabled]</td></tr><tr><td>Configured as eSATA</td><td>Hot Plug supported</td><td rowspan="9">&gt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; ExitESC: Exit</td></tr><tr><td>External</td><td>[Disabled]</td></tr><tr><td>Spin Up Device</td><td>[Disabled]</td></tr><tr><td>SATA Device Type</td><td>[Hard Disk Drive]</td></tr><tr><td>Topology</td><td>[Unknown]</td></tr><tr><td>SATA Port 0 DevSlp</td><td>[Enabled]</td></tr><tr><td>DITO Configuration</td><td>[Disabled]</td></tr><tr><td>DITO Value</td><td>625</td></tr><tr><td>DM Value</td><td>15</td></tr><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>SATA Controller(s)</td><td>DisabledEnabled</td><td>Enable/Disable SATA Device.</td></tr><tr><td>SATA Mode Selection</td><td>AHCIIntel RST PremiumWith Intel OptaneSystem Acceleration</td><td>Determines how SATA controller(s) operate.</td></tr><tr><td>SATA Test Mode</td><td>DisabledEnabled</td><td>Test Mode Enable/Disable (Loop Back).</td></tr><tr><td>&gt; Software Feature Mask Configuration</td><td>Submenu</td><td></td></tr><tr><td>Aggressive LPM Support</td><td>DisabledEnabled</td><td>Enable PCH to aggressively enter link power state.</td></tr><tr><td>SATA Controller Speed</td><td>Default, Gen1, Gen2, Gen3</td><td>Indicates the maximum speed the SATA controller can support.</td></tr><tr><td>Serial ATA Port X</td><td>Info-only</td><td></td></tr><tr><td>Software Preserve</td><td>Info-only</td><td></td></tr><tr><td>Port X</td><td>DisabledEnabled</td><td>Enable or Disable SATA Port</td></tr><tr><td>Hot Plug</td><td>DisabledEnabled</td><td>Designates this port as Hot Pluggable.</td></tr><tr><td>Configured as eSATA</td><td>Info-only</td><td></td></tr><tr><td>External</td><td>DisabledEnabled</td><td>Marks this port as external.</td></tr><tr><td>Spin Up Device</td><td>DisabledEnabled</td><td>If enabled for any of ports Staggerred Spin Up will be performed and only the drives which have this option enabled will spin up at boot. Otherwise all drives spin up at boot.</td></tr><tr><td>SATA Device Type</td><td>Hard Disk DriveSolid State Drive</td><td>Identify the SATA port is connected to Solid State Drive or Hard Disk Drive</td></tr><tr><td>Topology</td><td>UnknownISATADirect ConnectFlexM2</td><td>Identify the SATA Topology if it is Default or ISATA or Flex or DirectConnect or M2</td></tr><tr><td>SATA Port X DevSlp</td><td>DisabledEnabled</td><td>Enable/Disable SATA Port X DevSlp. For DevSlp to work, both hard drive and SATA port need to support DevSlp function, otherwise an unexpected behavior might happen. Please check board design before enabling it.</td></tr><tr><td>DITO Configuration</td><td>DisabledEnabled</td><td>Enable/Disable DITO Configuration</td></tr><tr><td>DITO Value</td><td>625</td><td>DITO Value</td></tr><tr><td>DM Value</td><td>15</td><td>DM Value</td></tr></table>

# 4.2.2 Software Feature Mask Configuration

Aptio Setup – AMI
Chipset

<table><tr><td colspan="2">Software Feature Mask Configuration</td></tr><tr><td rowspan="2">HDD Unlock [Enabled]LED Locate [Enabled]</td><td></td></tr><tr><td>&gt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; ExitESC: Exit</td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>HDD Unlock</td><td>DisabledEnabled</td><td>If enabled, indicates that the HDD password unlock in the OS is enabled.</td></tr><tr><td>LED Locate</td><td>DisabledEnabled</td><td>If enabled, indicates that the LED/SGPIO hardware is attached and ping to locate feature is enabled on the OS.</td></tr></table>

# 4.2.3 USB Configuration

Aptio Setup – AMI
Chipset

<table><tr><td>USB Configuration</td><td rowspan="3"></td></tr><tr><td>xDCI Support [Disabled]USB2 PHY Sus Well Power Gating [Enabled]USB3 Link Speed Selection [GEN1]</td></tr><tr><td>USB PDO Programming [Enabled]XHCI LTR Mode [Enabled]USB Overcurrent [Enabled]USB Overcurrent Lock [Enabled]</td></tr><tr><td></td><td>&gt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; ExitESC: Exit</td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>xDCI Support</td><td>DisabledEnabled</td><td>Enable/Disable xDCI (USB OTG Device).</td></tr><tr><td>USB2 PHY Sus Well Power Gating</td><td>DisabledEnabled</td><td>Select &#x27;Enabled&#x27; to enable SUS Well PG for USB2 PHY. This option has no effect on PCH-H</td></tr><tr><td>USB3 Link Speed Selection</td><td>GEN1GEN2</td><td>This option is to select USB3 Link Speed GEN1 or GEN2</td></tr><tr><td>USB PDO Programming</td><td>DisabledEnabled</td><td>Select &#x27;Enabled&#x27; if Port Disable Override functionality is used.</td></tr><tr><td>XHCI LTR Mode</td><td>DisabledEnabled</td><td>Enable/Disable XHCI LTR Mode</td></tr><tr><td>USB Overcurrent</td><td>DisabledEnabled</td><td>Select &#x27;Disabled&#x27; for pin-based debug. If pin-based debug is enabled but USB overcurrent is not disabled, USB DbC does not work.</td></tr><tr><td>USB Overcurrent Lock</td><td>DisabledEnabled</td><td>Select &#x27;Enabled&#x27; if Overcurrent functionality is used. Enabling this will make xHCI controller consume the Overcurrent mapping data</td></tr></table>

# 4.2.4 Security Configuration

Aptio Setup – AMI
Chipset

<table><tr><td colspan="2">Security Configuration</td><td rowspan="4"></td></tr><tr><td>RTC Memory Lock</td><td>[Enabled]</td></tr><tr><td>BIOS Lock</td><td>[Disabled]</td></tr><tr><td>Force unlock on all GPIO pads</td><td>[Disabled]</td></tr><tr><td></td><td></td><td>&gt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; ExitESC: Exit</td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>RTC Memory Lock</td><td>DisabledEnabled</td><td>Enable will lock bytes 38h-3Fh in the lower/upper 128-byte bank of RTC RAM</td></tr><tr><td>BIOS Lock</td><td>DisabledEnabled</td><td>Enable/Disable the PCH BIOS Lock Enable feature. Required to be enabled to ensure SMM protection of flash.</td></tr><tr><td>Force unlock on all GPIO pads</td><td>DisabledEnabled</td><td>If Enabled BIOS will force all GPIO pads to be in unlocked state</td></tr></table>

# 4.2.5 HD Audio Configuration

Aptio Setup – AMI
Chipset

<table><tr><td colspan="2">HD Audio Subsystem Configuration Settings</td></tr><tr><td>HD Audio</td><td>[Enabled]</td></tr><tr><td></td><td>&gt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; ExitESC: Exit</td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>HD Audio</td><td>DisabledEnabled</td><td>Control Detection of the HD-Audio device.</td></tr></table>

# 4.2.6 Serial IO Configuration

Aptio Setup – AMI
Chipset

<table><tr><td rowspan="2">Seriallo ConfigurationUART0 Controller [Disabled]</td><td></td></tr><tr><td>&gt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; ExitESC: Exit</td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>UARTO Controller</td><td>DisabledEnabledCommunication port (COM)</td><td>Enables/Disables Seriallo Controller</td></tr></table>

# 4.2.7 PCH Thermal Throttling Control

Aptio Setup – AMI
Chipset

<table><tr><td rowspan="2">Thermal Throttling Level [Suggested Setting]DMI Thermal Setting [Suggested Setting]SATA Thermal Setting [Suggested Setting]</td><td></td></tr><tr><td>&gt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; ExitESC: Exit</td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>Thermal Throttling Level</td><td>Suggested Setting Manual</td><td>Determine if use Intel suggested setting</td></tr><tr><td>DMI Thermal Setting</td><td>Suggested Setting Manual</td><td>Determine if use Intel suggested setting</td></tr><tr><td>SATA Thermal Setting</td><td>Suggested Setting Manual</td><td>Determine if use Intel suggested setting</td></tr></table>

# 5 Server Mgmt Menu

This menu contains the settings for IPMI BMC in the system.

Aptio Setup – AMI

<table><tr><td colspan="6">Main Advanced Chipset Server Mgmt Security Boot Save &amp; Exit</td></tr><tr><td>BMC Self Test Status</td><td></td><td>PASSED</td><td></td><td></td><td></td></tr><tr><td>BMC Device ID</td><td></td><td>18</td><td></td><td></td><td></td></tr><tr><td>BMC Device Revision</td><td></td><td>80</td><td></td><td></td><td></td></tr><tr><td>BMC Firmware Revision</td><td></td><td>0.04</td><td></td><td></td><td></td></tr><tr><td>IPMI Version</td><td></td><td>2.0</td><td></td><td></td><td></td></tr><tr><td>IPMI BMC Interface</td><td></td><td>KCS</td><td></td><td></td><td></td></tr><tr><td>BMC Support</td><td></td><td>[Enabled]</td><td></td><td></td><td></td></tr><tr><td>&gt;System Event Log</td><td></td><td></td><td></td><td></td><td></td></tr><tr><td>brid ARU information</td><td></td><td></td><td></td><td rowspan="5">&gt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; Exit</td><td></td></tr><tr><td>&gt;BMC network configuration</td><td></td><td></td><td></td><td></td></tr><tr><td>&gt;ADLINK IPMI configuration</td><td></td><td></td><td></td><td></td></tr><tr><td>&gt;View System Event Log</td><td></td><td></td><td></td><td></td></tr><tr><td>&gt;BMC User Setting</td><td></td><td></td><td></td><td></td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>BMC Self Test Status</td><td>Info-only</td><td></td></tr><tr><td>BMC Device ID</td><td>Info-only</td><td></td></tr><tr><td>BMC Device Revision</td><td>Info-only</td><td></td></tr><tr><td>BMC Firmware Revision</td><td>Info-only</td><td></td></tr><tr><td>IPMI Version</td><td>Info-only</td><td></td></tr><tr><td>IPMI BMC Interface</td><td>Info-only</td><td></td></tr><tr><td>BMC Support</td><td>DisabledEnabled</td><td>Enable/Disable interfaces to communicate with BMC</td></tr><tr><td>&gt;System Event Log</td><td>Submenu</td><td></td></tr><tr><td>implied by RFU information</td><td>Submenu</td><td></td></tr><tr><td>&gt;BMC network configuration</td><td>Submenu</td><td></td></tr><tr><td>&gt;ADLINK IPMI configuration</td><td>Submenu</td><td></td></tr><tr><td>&gt;View System Event Log</td><td>Submenu</td><td>Enter to check SEL.</td></tr><tr><td>&gt;BMC User Setting</td><td>Submenu</td><td>Enter to modify BMC user setting.</td></tr></table>

# 5.1 System Event Log

Aptio Setup – AMI

Server Mgmt

<table><tr><td>Enabling/Disabling OptionsSEL Components [Enabled]</td><td rowspan="4"></td></tr><tr><td>Erasing SettingsErase SEL [No]When SEL is Full [Do Nothing]</td></tr><tr><td>Custom EFI Logging OptionsLog EFI Status Codes [Error code]</td></tr><tr><td rowspan="2">NOTE: All values changed here do not take effect until computer is restarted.</td></tr><tr><td>&gt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; ExitESC: Exit</td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>SEL Components</td><td>DisabledEnabled</td><td>Change this to enable or disable event logging for error/progress codes during boot.</td></tr><tr><td>Erase SEL</td><td>NoYes, On next resetYes, On every reset</td><td>Choose options for erasing SEL.</td></tr><tr><td>When SEL is Full</td><td>Do NothingErase Immediately</td><td>Choose options for reactions to a full SEL.</td></tr><tr><td>Log EFI Status Codes</td><td>DisabledBothError codeProgress code</td><td>Disable the logging of EFI Status Codes or log only error code or only progress code or both.</td></tr></table>

# 5.2 View FRU Information

Aptio Setup – AMI

Server Mgmt

FRU information

<table><tr><td>Board Manufacturer</td><td>ADLINK</td></tr><tr><td>Board Product</td><td>VPX6200</td></tr><tr><td>Board Serial Number</td><td>PPS0000001</td></tr><tr><td>Board Part Number</td><td>55-31129</td></tr><tr><td>Product Manufacturer</td><td>ADLINK</td></tr><tr><td>Product Name</td><td>VPX6200</td></tr><tr><td>Product Part Number</td><td>91-31129</td></tr><tr><td>Product Version</td><td>Rev A2</td></tr><tr><td>Product Serial Number</td><td>0000001</td></tr></table>

NOTE: No FRU information for fields indicate information needs to be filled by O.E.M
>&lt;: Select Screen
^v: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F8: Previous Values
F9: Optimized Default
F10: Save & Exit
ESC: Exit

&lt;table&gt;<tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>Board Manufacturer</td><td>Info-only</td><td></td></tr><tr><td>Board Product</td><td>Info-only</td><td></td></tr><tr><td>Board Serial Number</td><td>Info-only</td><td></td></tr><tr><td>Board Part Number</td><td>Info-only</td><td></td></tr><tr><td>Product Manufacturer</td><td>Info-only</td><td></td></tr><tr><td>Product Name</td><td>Info-only</td><td></td></tr><tr><td>Product Part Number</td><td>Info-only</td><td></td></tr><tr><td>Product Version</td><td>Info-only</td><td></td></tr><tr><td>Product Serial Number</td><td>Info-only</td><td></td></tr></table>

# 5.3 BMC Network Configuration

Aptio Setup – AMI
Server Mgmt

<table><tr><td colspan="2">--BMC network configuration--**********Configure IPv4 support**********</td><td rowspan="2"></td></tr><tr><td>LAN channel 1Configuration Address sourceCurrent Configuration Address sourceStation IP addressSubnet maskStation MAC addressRouter IP address</td><td>[Unspecified]StaticAddressxxx.xxx.xxx.xxxxxx.xxx.xx-xx-xx-xx-xx-xxxxx.xxx.xxx.xxx</td></tr><tr><td>LAN channel 2Configuration Address sourceCurrent Configuration Address sourceStation IP addressSubnet maskStation MAC addressRouter IP address</td><td>[Unspecified]StaticAddressxxx.xxx.xxx.xxxxxx.xxx.xx-xx-xx-xx-xx-xxxxx.xxx.xxx.xxx.xxx</td><td>&gt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; ExitESC: Exit</td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>Configuration Address source</td><td>Unspecified Static</td><td>Select to configure LAN channel parameters statically or dynamically (by BIOS or BMC). Unspecified option will not modify any BMC network parameters during BIOS phase</td></tr><tr><td>Current Configuration Address source</td><td>Info-only</td><td></td></tr><tr><td>Station IP address</td><td>Info-only</td><td></td></tr><tr><td>Subnet mask</td><td>Info-only</td><td></td></tr><tr><td>Station MAC address</td><td>Info-only</td><td></td></tr><tr><td>Router IP address</td><td>Info-only</td><td></td></tr></table>

# 5.4 ADLINK IPMI Configuration

Aptio Setup – AMI
Server Mgmt

<table><tr><td>PCB Version</td><td>A1</td><td rowspan="9"></td></tr><tr><td>Geographical Address</td><td>0x1E</td></tr><tr><td>System Controller</td><td>Host</td></tr><tr><td>NVMRO Signal</td><td>Non Protect</td></tr><tr><td>NVMRO item Control</td><td>[Non-Protect]</td></tr><tr><td>SYS_RESET Support</td><td>[Enabled]</td></tr><tr><td>GA Status</td><td>It&#x27;s GA 17</td></tr><tr><td>SBC Control Status</td><td>3x SBC (GA17/18/19)</td></tr><tr><td>SBC Control</td><td>[3x SBC (GA17/18/19)]</td></tr><tr><td></td><td></td><td>&gt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; ExitESC: Exit</td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>PCB Version</td><td>Info-only</td><td></td></tr><tr><td>Geographical Address</td><td>Info-only</td><td></td></tr><tr><td>System Controller</td><td>Info-only</td><td></td></tr><tr><td>NVMRO Signal</td><td>Info-only</td><td></td></tr><tr><td>NVMRO item Control</td><td>Protect Non-Protect</td><td>Enable or disable NVMRO Control support.</td></tr><tr><td>SYS_RESET Support</td><td>Disabled Enabled</td><td>Enable or disable SYS_RESET support.</td></tr><tr><td>SBC Control Status</td><td>Info-only</td><td>Show the SBC control Status from IPMC</td></tr><tr><td>SBC Control</td><td>1x SBC (GA17)2x SBC (GA17/18)3x SBC (GA17/18/19)</td><td>Send SBC control Status to IPMC</td></tr></table>

# 5.5 View System Event Log

Aptio Setup – AMI Server Mgmt

<table><tr><td colspan="3">No. of log entries in SEL : xxx</td><td rowspan="2"></td></tr><tr><td>DATE</td><td>TIME</td><td>SENSOR TYPE</td></tr><tr><td></td><td></td><td></td><td>&gt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; ExitESC: Exit</td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>System Event Log</td><td>Info-only</td><td>To display System Event Logs (SEL).</td></tr></table>

# 5.6 BMC User Settings

Aptio Setup – AMI Server Mgmt

<table><tr><td>BMC User Settings</td><td></td></tr><tr><td>&gt; Add User</td><td rowspan="3">&gt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous Values</td></tr><tr><td>&gt; Delete User</td></tr><tr><td>&gt; Change User Settings</td></tr><tr><td></td><td>F9: Optimized DefaultF10: Save &amp; ExitESC: Exit</td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>BMC User Settings</td><td>Info-only</td><td>To config BMC user settings.</td></tr></table>

# 6 Security Menu

This menu contains the settings for security in the system.

Aptio Setup – AMI

<table><tr><td colspan="3">Main Advanced Chipset Boot Security Save &amp; Exit</td></tr><tr><td colspan="2">Password DescriptionIf ONLY the Administrator&#x27;s password is set,then this only limits access to Setup and isOnly asked for when entering Setup.If ONLY the User&#x27;s password is set, then thisis a power on password and must be entered toboot or enter Setup. In Setup the user willhave Administrator rights.The password length must bein the following range:Minimum length 3Maximum length 20</td><td></td></tr><tr><td colspan="2">Administrator PasswordUser Password</td><td rowspan="3">&lt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; ExitESC: Exit</td></tr><tr><td colspan="2">HDD Security Configuration</td></tr><tr><td colspan="2">&gt; Secure Boot menu</td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>Administrator Password</td><td>Enter to set password</td><td>Configure/Clear Administrator Password.When pressing enter, a menu will be popped up for creating new password. When password installed, press enter without inputting password, it will clear password.</td></tr><tr><td>User Password</td><td>Enter to set password</td><td>Configure/Clear User Password. When pressing enter, a menu will be popped up for creating new password. When password installed, press enter without inputting password, it will clear password.</td></tr><tr><td>HDD Security Configuration</td><td>Submenu</td><td>For HDD security, it will list all HDD detected on motherboard. Select the HDD and then press enter can figure/clear HDD password.</td></tr><tr><td>Secure Boot menu</td><td>Submenu</td><td></td></tr></table>

When selecting a HDD to configure passwords, BIOS will enter another new BIOS setup page like below. The method of configuring HDD password is the same as BIOS passwords. Once password is set, it will reflect the status on the screen, like ‘INSTALLED’ change on ‘HDD User Pwd Status’. When there is no HDD user password installed, you can always change master password without confirming the latest installed password. Once HDD user password is installed, HDD master password is not allowed changing.

Aptio Setup – AMI
Security

<table><tr><td>HDD Password Description</td><td></td></tr><tr><td>Allows Access to Set, Modify and ClearHardDisk User and Master Passwords.User Password need to be installed forEnabling Security. Master Password canbe Modified only when successfully unlockedwith Master Password in POST</td><td></td></tr><tr><td>HDD PASSWORD CONFIGURATION</td><td></td></tr><tr><td>Security Supported Yes</td><td></td></tr><tr><td>Security Enabled Yes</td><td></td></tr><tr><td>Security Locked No</td><td></td></tr><tr><td>Security Frozen No</td><td></td></tr><tr><td>HDD User Pwd Status INSTALLED</td><td rowspan="2">&lt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; ExitESC: Exit</td></tr><tr><td>HDD Master Pwd Status INSTALLED</td></tr><tr><td>Set User Password</td><td></td></tr><tr><td>Set Master Password</td><td></td></tr></table>

# 6.1 Secure Boot

Aptio Setup – AMI
Security

<table><tr><td>System Mode</td><td>User</td><td></td></tr><tr><td>Secure Boot</td><td>[Disabled]Not Active</td><td></td></tr><tr><td>Secure Boot Mode</td><td>[Standard]</td><td></td></tr><tr><td>&gt;Restore Factory Keys</td><td></td><td rowspan="2">&gt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General Help</td></tr><tr><td>&gt;Reset To Setup Mode</td><td></td></tr><tr><td>&gt;Key Management</td><td></td><td>F8: Previous ValuesF9: Optimized DefaultF10: Save &amp; ExitESC: Exit</td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>System Mode</td><td>Info-only</td><td></td></tr><tr><td>Secure Boot</td><td>DisabledEnabled</td><td>Secure Boot feature is Active if Secure Boot is Enabled,</td></tr><tr><td>Secure Boot Mode</td><td>StandardCustom</td><td>Secure Boot mode options</td></tr></table>

# 7 Boot Menu

This menu contains the settings for bootable devices in the system.

Aptio Setup – AMI.

<table><tr><td colspan="6">Boot Configuration</td></tr><tr><td colspan="2">Setup Prompt Timeout</td><td colspan="3">1</td><td rowspan="10"></td></tr><tr><td colspan="2">Bootup NumLock State</td><td colspan="3">[On]</td></tr><tr><td colspan="2">Quiet Boot</td><td colspan="3">[Enabled]</td></tr><tr><td colspan="2">Fast Boot</td><td colspan="3">[Disabled]</td></tr><tr><td colspan="2">Boot mode select</td><td colspan="3">[UEFI]</td></tr><tr><td colspan="5">Boot Configuration</td></tr><tr><td colspan="2">Boot Option #1</td><td colspan="3">[Hard Disk]</td></tr><tr><td colspan="2">Boot Option #2</td><td colspan="3">[NVMe]</td></tr><tr><td colspan="2">Boot Option #3</td><td colspan="3">[Built-in EFI Shell]</td></tr><tr><td colspan="2">Boot Option #4</td><td colspan="3">[CD/DVD]</td></tr><tr><td colspan="2">Boot Option #5</td><td colspan="3">[SD]</td><td rowspan="7">&lt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; ExitESC: Exit</td></tr><tr><td colspan="2">Boot Option #6</td><td colspan="3">[USB Hard Disk]</td></tr><tr><td colspan="2">Boot Option #7</td><td colspan="3">[USB CD/DVD]</td></tr><tr><td colspan="2">Boot Option #8</td><td colspan="3">[USB Key]</td></tr><tr><td colspan="2">Boot Option #9</td><td colspan="3">[USB Floppy]</td></tr><tr><td colspan="2">Boot Option #10</td><td colspan="3">[USB Lan]</td></tr><tr><td colspan="2">Boot Option #11</td><td colspan="3">[Network]</td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>Setup Prompt Timeout</td><td>1</td><td>Number of seconds to wait for setup activation key. 65535 (0xFFFF) means indefinite waiting.</td></tr><tr><td>Bootup NumLock State</td><td>On Off</td><td>Select the keyboard NumLock state after system boot.</td></tr><tr><td>Quiet Boot</td><td>Disabled Enabled</td><td>Enabled: will show splash screen during POST. Disabled: will show boot message during POST.</td></tr><tr><td>Fast Boot</td><td>Disabled Enabled</td><td>Enable or disabled Fast boot feature. Most probes are skipped to reduce time cost during boot.</td></tr><tr><td>Boot mode select</td><td>LEGADY UEFI</td><td>Select boot mode, LEGACY/UEFI.</td></tr><tr><td>Boot Option #1~#11</td><td>Hard DiskNVMECD/DVDSDUSB Hard DiskUSB CD/DVDUSB KeyUSB FloppyUSB LanNetworkDisabled</td><td>Set system boot order.</td></tr></table>

# 8 Save & Exit

Aptio Setup – AMI

<table><tr><td colspan="2">Main Advanced Chipset Server Mgmt Security Boot Save &amp; Exit</td></tr><tr><td rowspan="2">Save OptionsSave Changes and ExitDiscard Changes and ExitSave Changes and ResetDiscard Changes and ResetSave ChangesDiscard ChangesDefault OptionsRestore DefaultsSave as User DefaultsRestore User DefaultsBoot OverrideLaunch EFI Shell from filesystem device</td><td>Exit system setup after saving the changes.</td></tr><tr><td>&lt;&lt;: Select Screen^v: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF8: Previous ValuesF9: Optimized DefaultF10: Save &amp; ExitESC: Exit</td></tr></table>

<table><tr><td>BIOS Item</td><td>Options</td><td>Description</td></tr><tr><td>Save Changes and Exit</td><td>Enter</td><td>Save changed settings and exit BIOS setup utility.</td></tr><tr><td>Discard Changes and Exit</td><td>Enter</td><td>Skip changed setting and exit BIOS setup utility.</td></tr><tr><td>Save Changes and Reset</td><td>Enter</td><td>Save all changed settings and let system do reset to boot system.</td></tr><tr><td>Discard Changes and Reset</td><td>Enter</td><td>Discard all changed settings and let system do reset to boot system.</td></tr><tr><td>Save Changes</td><td>Enter</td><td>Save all changed settings.</td></tr><tr><td>Discard Changes</td><td>Enter</td><td>Discard changes done so far to any of the setup options.</td></tr><tr><td>Restore Default</td><td>Enter</td><td>Load the default made when BIOS was built.</td></tr><tr><td>Save as User Default</td><td>Enter</td><td>Save all changed done so far as User Defaults.</td></tr><tr><td>Restore User Default</td><td>Enter</td><td>Load the default that user save as user defaults.</td></tr><tr><td>Boot Override</td><td>Info-only</td><td></td></tr></table>

# Important Safety Instructions

For user safety, please read and follow all instructions, WARNINGS, CAUTIONS, and NOTES marked in this manual and on the associated equipment before handling/operating the equipment.

1. Read these safety instructions carefully.
2. Keep this user’s manual for future reference.
3. Read the specifications section of this manual for detailed information on the operating environment of this equipment.
4. The equipment can be operated at an ambient temperature of $40 ^ { \circ } \mathsf { C }$ .

5. When installing/mounting or uninstalling/removing equipment; or when removal of the chassis lid required for user servicing (Section 3.1-3.5):

• Turn off power and unplug any power cords/cables, and

6. To avoid electrical shock and/or damage to equipment:

• Keep equipment away from water or liquid sources;
• Keep equipment away from high heat or high humidity;
• Keep equipment properly ventilated (do not block or cover ventilation openings);
• Make sure to use recommended voltage and power source settings;
• Always install and operate equipment near an easily accessible electrical socketoutlet;
• Secure the power cord (do not place any object on/over the power cord);
Only install/attach and operate equipment on stable surfaces and/or recommended mountings;
If the equipment will not be used for long periods of time, turn off and unplug the equipment from its power source.
• The power cord must be connected to a socket or outlet with a ground connection.

7. Never attempt to fix the equipment. Equipment should only be serviced by qualified personnel.

8. This equipment is not suitable for use in locations where children are likely to be present.
9. Equipment must be serviced by authorized technicians when:

• The power cord or plug is damaged;
Liquid has penetrated the equipment;
It has been exposed to high humidity/moisture;
• It is not functioning or does not function according to the user’s manual;
• It has been dropped and/or damaged; and/or,
It has an obvious sign of breakage.

10.Please pay strict attention to all warnings and advisories appearing on the device, to avoid injury or damage.

11.It is recommended that equipment be installed only in a server room or computer room where access is:

Restricted to qualified service personnel or users familiar with restrictions applied to the location, reasons therefor, and any precautions required;
Only afforded by the use of a tool or lock and key, or other means of security, and is controlled by the authority responsible for the location.

12.Suitable for installation in Information Technology Rooms in accordance with Article 645 of the National Electrical Code and NFPA 75.

# Getting Service

Ask an Expert: https://www.adlinktech.com/en/Askanexpert

# ADLINK Technology, Inc.

Address: No. 66, Huaya 1st Rd., Guishan District

Taoyuan City 333411, Taiwan

333411 桃園市龜山區華亞一路 66 號

Tel: +886-3-216-5088

Fax: +886-3-328-5706

Email: service@adlinktech.com

# Ampro ADLINK Technology, Inc.

6450 Via Del Oro, San Jose, CA 95119-1208, USA

Tel: +1-408-360-0200

Toll Free: +1-800-966-5200 (USA only)

Fax: +1-408-600-1189

Email: info@adlinktech.com

# ADLINK Technology (China) Co., Ltd.

Address: 上海市浦东新区张江高科技园区芳春路 300 号 (201203)

300 Fang Chun Rd., Zhangjiang Hi-Tech Park, Pudong New Area

Shanghai, 201203 China

Tel: +86-21-5132-8988

Fax: +86-21-5132-3588

Email: market@adlinktech.com

# ADLINK Technology GmbH

Address: Hans-Thoma-Strasse 11, D-68163, Mannheim, Germany

Tel: +49-621-43214-0

Fax: +49-621 43214-30

Email: emea@adlinktech.com

Please visit the Contact page at www.adlinktech.com for information on how to contact the ADLINK regional office nearest you.
[🔗 Link to the original document](.vpx6200-bios-50m-31428-2000-10/vpx6200-bios-50m-31428-2000-10.pdf)